Table of Contents Author Guidelines Submit a Manuscript
International Journal of Rotating Machinery
Volume 2006, Article ID 56420, 11 pages
http://dx.doi.org/10.1155/IJRM/2006/56420

Two-Dimensional Rotating Stall Analysis in a Wide Vaneless Diffuser

1Section of Energy Technology, Division Thermo Fluids Engineering, Department of Mechanical Engineering, Eindhoven University of Technology, Den Dolech 2, Eindhoven, MB 5600, The Netherlands
2Department of Flow and Structural Dynamics, TNO Science and Industry, P.O. Box 155, Delft, AD 2600, The Netherlands

Received 26 August 2005; Accepted 7 September 2005

Copyright © 2006 S. Ljevar et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. F. P. T. Willems, Modeling and bounded feedback stabilization of centrifugal compressor surge, M.S. thesis, Technische Universiteit Eindhoven, Eindhoven, The Netherlands, 2000, printed by University Press Facilities.
  2. A. N. Abdelhamid and J. Bertrand, “Distinctions between two types of self-excited gas oscillations in vaneless radial diffusers,” Canadian Aeronautics and Space Journal, vol. 26, pp. 105–117, 1980, ASME Paper 79-GT-58. View at Google Scholar
  3. H.-S. Dou, “Investigation of the Prediction of Losses in Radial Vaneless Diffusers,” 1991, ASME Paper 91-GT-323. View at Google Scholar
  4. Y. H. Shin, K. H. Kim, and B. J. Son, “An experimental study on the development of a reverse flow zone in a vaneless diffuser,” JSME International Journal Series B, vol. 41, no. 3, pp. 546–555, 1998. View at Google Scholar
  5. W. Jansen, “Rotating stall in a radial vaneless diffuser,” ASME Journal of Basic Engineering, vol. 86, pp. 750–758, 1964. View at Google Scholar
  6. Y. Senoo and Y. Kinoshita, “Influence of inlet flow conditions and geometries of centrifugal vaneless diffusers on critical flow angle for reverse flow,” ASME Journal of Fluids Engineering, vol. 99, pp. 98–103, 1977. View at Google Scholar
  7. P. Frigne and R. Van den Braembussche, “Distinction between different types of impeller and diffuser rotating stall in a centrifugal compressor with vaneless diffuser,” ASME Journal of Engineering for Gas Turbines and Power, vol. 106, no. 2, pp. 468–474, 1984. View at Google Scholar
  8. H.-S. Dou and S. Mizuki, “Analysis of the flow in vaneless diffusers with large width-to-radius ratios,” ASME Journal of Turbomachinery, vol. 120, pp. 193–201, 1998. View at Google Scholar
  9. A. N. Abdelhamid, “Analysis of Rotating Stall in Vaneless Diffusers of Centrifugal Compressors,” 1980, ASME Paper 80-GT-184; New Orleans, La, USA. View at Google Scholar
  10. Y. Tsujimoto, Y. Yoshida, and Y. Mori, “Study of vaneless diffuser rotating stall based on two-dimensional inviscid flow analysis,” ASME Journal of Fluids Engineering, vol. 118, pp. 123–127, 1996. View at Google Scholar
  11. A. N. Abdelhamid, “Effects of vaneless diffuser geometry on flow instability in centrifugal compression systems,” Canadian Aeronautics and Space Journal, vol. 29, pp. 259–266, 1983. View at Google Scholar
  12. G. Ferrara, L. Ferrari, C. P. Mengoni, M. De Lucia, and L. Baldassarre, “Experimental investigation and characterization of the rotating stall in a high pressure centrifugal compressor. Part I: Influence of diffuser geometry on stall inception,” in Proceedings of ASME Turbo Expo, Amsterdam, The Netherlands, June 2002.
  13. G. Ferrara, L. Ferrari, C. P. Mengoni, M. De Lucia, and L. Baldassarre, “Experimental investigation and characterization of the rotating stall in a high pressure centrifugal compressor. Part II: Influence of diffuser geometry on stage performance,” in Proceedings of ASME Turbo Expo, Amsterdam, The Netherlands, June 2002.
  14. A. Cellai, G. Ferrara, L. Ferrari, C. P. Mengoni, and L. Baldassarre, “Experimental investigation and characterization of the rotating stall in a high pressure centrifugal compressor. Part III: Influence of diffuser geometry on stall inception and performance (II impeller) ,” in Proceedings of ASME Turbo Expo, Atlanta, Ga, USA, June 2003.
  15. A. Cellai, G. Ferrara, L. Ferrari, C. P. Mengoni, and L. Baldassarre, “Experimental investigation and characterization of the rotating stall in a high pressure centrifugal compressor. Part IV: Impeller influence on diffuser stability,” in Proceedings of ASME Turbo Expo, Atlanta, Ga, USA, June 2003.
  16. S. Ljevar, H. C. de Lange, and A. A. van Steenhoven, “Rotating stall characteristics in a wide vaneless diffuser,” in Proceedings of ASME Turbo Expo, Reno-Tahoe, Nev, USA, June 2005.
  17. H. Cohen, G. F. C. Rogers, and H. I. H. Saravanamuttoo, Gas Turbine Theory, Addison-Wesley Longman, Harlow, UK, 4th edition, 1996.
  18. B. P. Leonard, “A stable and accurate convective modelling procedure based on quadratic upstream interpolation,” Computer Methods in Applied Mechanics and Engineering, vol. 19, no. 1, pp. 59–98, 1979. View at Google Scholar
  19. H. Tsurusaki and T. Kinoshita, “Flow control of rotating stall in a radial vaneless diffuser,” ASME Journal of Basic Engineering, vol. 123, pp. 281–286, 2001. View at Google Scholar