Table of Contents Author Guidelines Submit a Manuscript
International Journal of Rotating Machinery
Volume 2014, Article ID 704315, 11 pages
http://dx.doi.org/10.1155/2014/704315
Research Article

Effect of Chamfer Angle on the Calibration Curves of Five Hole Probes

Thermal Turbomachines Laboratory, Department of Mechanical Engineering, IIT Madras, Chennai 600 036, India

Received 30 May 2014; Accepted 28 August 2014; Published 15 September 2014

Academic Editor: Takayuki Matsunuma

Copyright © 2014 Nekkanti Sitaram and Kancherla Srikanth. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. A. L. Treaster and A. M. Yocum, “The calibration and application of five-hole probes,” ISA Transactions, vol. 18, no. 3, pp. 23–34, 1979. View at Google Scholar · View at Scopus
  2. V. Malviya, R. Mishra, and E. Palmer, “CFD investigation on 3-dimensional interference of a five-hole probe in an automotive wheel arch,” Advances in Mechanical Engineering, vol. 2010, Article ID 763718, 19 pages, 2010. View at Publisher · View at Google Scholar · View at Scopus
  3. J. W. Naughton, L. N. Cattafesta III, and G. S. Settles, “Miniature, fast-response five-hole conical probe for supersonic flowfield measurements,” AIAA Journal, vol. 31, no. 3, pp. 453–458, 1993. View at Publisher · View at Google Scholar · View at Scopus
  4. I. M. Milanovic and I. M. Kalkhoran, “Numerical calibration of a conical five-hole probe for supersonic measurements,” Measurement Science and Technology, vol. 11, no. 12, pp. 1812–1818, 2000. View at Publisher · View at Google Scholar · View at Scopus
  5. S. J. Lien and N. A. Ahmed, “An examination of suitability of multi-hole pressure probe technique for skin friction measurement in turbulent flow,” Flow Measurement and Instrumentation, vol. 22, no. 3, pp. 215–224, 2011. View at Publisher · View at Google Scholar · View at Scopus
  6. D. Telionis, Y. Yang, and O. Rediniotis, “Recent developments in multi-hole probe technology,” in Proceedings of the 20th International Congress of Mechanical Engineering (COBEM '09), Gramado, Brazil, November 2009.
  7. P. M. Ligrani, B. A. Singer, and L. R. Baun, “Miniature five-hole pressure probe for measurement of three mean velocity components in low-speed flows,” Journal of Physics E: Scientific Instruments, vol. 22, no. 10, pp. 868–876, 1989. View at Publisher · View at Google Scholar · View at Scopus
  8. A. J. Pisasale and N. A. Ahmed, “A novel method for extending the calibration range of five-hole probe for highly three-dimensional flows,” Flow Measurement and Instrumentation, vol. 13, no. 1-2, pp. 23–30, 2002. View at Publisher · View at Google Scholar · View at Scopus
  9. K. M. A. Díaz, J. M. F. Oro, and E. B. Marigorta, “Direct calibration framework of triple-hole pressure probes for incompressible flow,” Measurement Science and Technology, vol. 19, no. 7, Article ID 075401, 2008. View at Publisher · View at Google Scholar · View at Scopus
  10. R. G. Dominy and H. P. Hodson, “An investigation of factors influencing the calibration of five-hole probes for three-dimensional flow measurements,” Journal of Turbomachinery, vol. 115, no. 3, pp. 513–519, 1993. View at Publisher · View at Google Scholar · View at Scopus
  11. N. Sitaram and M. Govardhan, “Large angle calibration of five hole probes,” Journal of the Aeronautical Society of India, vol. 54, no. 3, pp. 265–272, 2002. View at Google Scholar
  12. C. Venkateswara Babu, M. Govardhan, and N. Sitaram, “A method of calibration of a seven-hole pressure probe for measuring highly three-dimensional flows,” Measurement Science and Technology, vol. 9, no. 3, pp. 468–476, 1998. View at Publisher · View at Google Scholar · View at Scopus
  13. K. N. Everett, A. A. Gerner, and D. A. Durston, “Seven-hole probe for high angle flow measurement: theory and calibration,” AIAA Journal, vol. 21, no. 7, pp. 992–998, 1983. View at Publisher · View at Google Scholar · View at Scopus
  14. A. Pissasale and N. A. Ahmed, “Theoretical calibration of a five hole probe for highly three dimensional flow,” Measurement Science and Technology, vol. 13, pp. 1100–1107, 2002. View at Google Scholar
  15. A. J. Pisasale and N. A. Ahmed, “Development of a functional relationship between port pressures and flow properties for the calibration and application of multihole probes to highly three-dimensional flows,” Experiments in Fluids, vol. 36, no. 3, pp. 422–436, 2004. View at Publisher · View at Google Scholar · View at Scopus