Table of Contents
International Journal of Vehicular Technology
Volume 2009 (2009), Article ID 105363, 11 pages
http://dx.doi.org/10.1155/2009/105363
Research Article

The Effect of Different Injection Strategies and Intake Conditions on the Emissions Characteristics in a Diesel Engine

Department of Mechanical Engineering, University of Mazandaran, P. O. Box 484, Babol, Iran

Received 21 October 2008; Revised 16 January 2009; Accepted 11 March 2009

Academic Editor: Chonggang Wang

Copyright © 2009 M. Gorji-Bandpy et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. J. M. Desantes, R. Payri, F. J. Salvador, and A. Gil, “Development and validation of a theoretical model for diesel spray penetration,” Fuel, vol. 85, no. 7-8, pp. 910–917, 2006. View at Publisher · View at Google Scholar
  2. S. W. Park, S. Kim, and C. S. Lee, “Breakup and atomization characteristics of mono-dispersed diesel droplets in a cross-flow air stream,” International Journal of Multiphase Flow, vol. 32, no. 7, pp. 807–822, 2006. View at Publisher · View at Google Scholar
  3. S. S. Sazhin, “Advanced models of fuel droplet heating and evaporation,” Progress in Energy and Combustion Science, vol. 32, no. 2, pp. 162–214, 2006. View at Publisher · View at Google Scholar
  4. M. Zheng, G. T. Reader, and J. G. Hawley, “Diesel engine exhaust gas recirculation—a review on advanced and novel concepts,” Energy Conversion and Management, vol. 45, no. 6, pp. 883–900, 2004. View at Publisher · View at Google Scholar
  5. L. Wei, W. Ying, Z. Longbao, and S. Ling, “Study on improvement of fuel economy and reduction in emissions for stoichiometric gasoline engines,” Applied Thermal Engineering, vol. 27, no. 17-18, pp. 2919–2923, 2007. View at Publisher · View at Google Scholar
  6. T. C. Zannis, E. G. Pariotis, D. T. Hountalas, D. C. Rakopoulos, and Y. A. Levendis, “Theoretical study of DI diesel engine performance and pollutant emissions using comparable air-side and fuel-side oxygen addition,” Energy Conversion and Management, vol. 48, no. 11, pp. 2962–2970, 2007. View at Publisher · View at Google Scholar
  7. L. Andreassi, S. Ubertini, and L. Allocca, “Experimental and numerical analysis of high pressure diesel spray-wall interaction,” International Journal of Multiphase Flow, vol. 33, no. 7, pp. 742–765, 2007. View at Publisher · View at Google Scholar
  8. S. Finger, D. Gelman, A. Fay, M. Szczerban, A. Smailagic, and D. P. Siewiorek, “Supporting collaborative learning in engineering design,” Expert Systems with Applications, vol. 31, no. 4, pp. 734–741, 2006. View at Publisher · View at Google Scholar
  9. D. J. Torres and M. F. Trujillo, “KIVA-4: an unstructured ALE code for compressible gas flow with sprays,” Journal of Computational Physics, vol. 219, no. 2, pp. 943–975, 2006. View at Publisher · View at Google Scholar
  10. V. Hamosfakidis and R. D. Reitz, “Optimization of a hydrocarbon fuel ignition model for two single component surrogates of diesel fuel,” Combustion and Flame, vol. 132, no. 3, pp. 433–450, 2003. View at Publisher · View at Google Scholar
  11. J. K. Dukowicz, “A particle-fluid numerical model for liquid sprays,” Journal of Computational Physics, vol. 35, no. 2, pp. 229–253, 1980. View at Publisher · View at Google Scholar
  12. J. Senda and M. Kobayashi, “Modeling of diesel spray impingement on a flat wall,” SAE paper, SAE International, Warrendale, Pa, USA, 1984. View at Google Scholar
  13. J. K. Dukowicz, “Quasi-steady droplet phase change in the presence of convection,” Los Alamos Scientific Laboratory, New Mexico, NM, USA, August 1979. View at Google Scholar
  14. A. B. Liu and R. D. Reitz, “Modeling the effects of drop drag and break-up on fuel sprays,” SAE paper, SAE International, Warrendale, Pa, USA, March 1993. View at Google Scholar
  15. Y. B. Zel'dovich, P. Y. Sadovnikov, and D. A. Frank-Kamenetskii, “Oxidation of nitrogen in combustion,” Academy of Sciences of USSR, p. 209, 1947, translation by M. Shelef. View at Google Scholar
  16. W. Polifke, “Fundamental and practical limitations of NOx, reduction in lean-premixed combustion,” in Euroconference “Premixed Turbulent Combustion: Introduction to the State of the Art”, pp. 1–17, RWTH, Aachen, Germany, 1995. View at Google Scholar
  17. B. F. Magnussen and B. H. Hjertager, “On mathematical modeling of turbulent combustion with special emphasis on soot formation and combustion,” in Proceedings of the 16th International Symposium on Combustion, Pittsburgh, Pa, USA, 1977.
  18. A. D. Gosman and E. Loannides, “Aspects of computer simulation of liquid-fueled combustors,” Journal of Energy, vol. 7, no. 32, pp. 482–490, 1983. View at Google Scholar
  19. N. N. Mansour, J. Kim, and P. Moin, “Near-wall K-ε turbulence modeling,” AIAA Journal, vol. 27, no. 8, pp. 1068–1073, 1989. View at Google Scholar
  20. C. J. Rutland, N. Ayoub, Z. Han et al., “Diesel engine model and development and experiments,” SAE paper, SAE International, Warrendale, Pa, USA, 1995. View at Google Scholar
  21. G. P. Merker, C. Schwarz, G. Stiesch, and F. Otto, Simulating Combustion: Simulation of Combustion and Pollutant Formation for Engine-Development, Springer, Heidelberg, Germany, 2006.
  22. L. Dahlen, On applied CFD and model development in combustion systems development for DI diesel engines: prediction of soot mediated oil thickening, Doctoral thesis, Royal Institute of Technology, Stockholm, Sweden, 2002.
  23. J. B. Heywood, Internal Combustion Engine Fundamentals, McGraw-Hill, New York, NY, USA, 1988.
  24. R. Payri, F. J. Salvador, J. Gimeno, and J. de la Morena, “Effects of nozzle geometry on direct injection diesel engine combustion process,” Applied Thermal Engineering, vol. 29, no. 10, pp. 2051–2060, 2009. View at Publisher · View at Google Scholar