Assessment of Pseudoaffinity Chromatography Using Textile Dyes for Isolation of Buffalo Pituitary Luteinizing Hormone

Arora, Taruna; Patel, Pankaj; Muralidhar, K.

doi:https://doi.org/10.5402/2012/639514

International Scholarly Research Notices

On this page

Abstract Introduction Materials and Methods Results and Discussion Conclusions Acknowledgments References Copyright Related Articles

Research Article | Open Access

Volume 2012 | Article ID 639514 | https://doi.org/10.5402/2012/639514

Assessment of Pseudoaffinity Chromatography Using Textile Dyes for Isolation of Buffalo Pituitary Luteinizing Hormone

Taruna Arora,¹Pankaj Patel,²and K. Muralidhar¹

Academic Editor: L. Membrado, T. Oi, H. M. Rawel, L. Chen

Received29 Sept 2012

Accepted11 Nov 2012

Published16 Dec 2012

Abstract

Extensive investigation has been carried out to elucidate the mechanisms involved in pseudoligand affinity chromatography using textile dyes, and, empirically, it has been attributed to the chemical and steric structures of dye and protein. Possibly, a variety of interactions especially ionic and/or hydrophobic influence with a varying share in the binding and differ from protein to protein and from dye to dye. In this study, we have attempted to understand the effect of various biophysical parameters like the nature of the eluant, pH, and ionic strength on the binding of crude luteinizing hormone (LH) with various triazine-based dyes and thus predict their nature. Based on the elution patterns, cibacron and reactive brown suggested a dual electrostatic and hydrophobic nature. Reactive blue and reactive yellow reflected a major electrostatic/ionic nature with yellow offering 50-fold purification in a single step, while reactive red and reactive green had a predominant hydrophobic nature. Appreciably, reactive red was binding LH very tightly unlike other dyes, and addition of the arginine in the elution buffer substantially weakened the protein-dye interactions. pH was observed to be a principal factor assisting the protein-dye binding as well as hydrophobicity of the dye and the proteins.

1. Introduction

Dye ligand chromatography is rapidly arising as a suitable substitute to specific affinity chromatographies owing to their easy accessibility and economical and effortless immobilization. Despite being synthetic in nature, the triazine-based dyes have a high affinity for many proteins and enzymes [1–7]. In the immobilized form, the dye has rapidly been identified and used as an affinity ligand in chromatographic isolation of a variety of proteins including dehydrogenases, kinases, serum albumin, interferon, several plasma proteins, and a host of other proteins owing to their ability to mimic the configuration of substrates, cofactors, or binding agents, thereby leading to high recovery and many a time purity in tandem, both achieved in a single chromatographic step [8–11].

Most of the dye and protein interaction studies have been performed on the blue sepharose (cibacron blue linked to beaded agarose) involving different dehydrogenase [12, 13].

The affinity ligands both synthetic as well as biological are being designed using a variety of procedures; however, an interesting alternative is presently being offered in the form of biomimetic dyes or chimaeric dye-ligands involving a chloro-triazinlyl scaffold which is often replaced with various amino acids, carbocyclic, and heterocyclic groups, thereby producing ligand libraries. The design of these dyes is performed on the basis of either complementarity by studying a natural ligand-protein complex or mimicking a natural biological recognition interaction [14, 15].

As a prelude to realizing the full potential of these textile dyes, an understanding of the interactions of the dye with its cognate protein must be gained. It has been recognized that these dyes are capable of varying hydrophobic and/or ionic interactions with numerous proteins, but such information on all of the dyes is incomplete [16–18]. Also, a detailed study of available dyes for application to isolate a given protein is necessary.

Gonadotropins are regulatory hormones which control the reproductive processes in all vertebrates [19]. There is still a huge demand for native gonadotropins and thyrotropins, but homologous, for therapeutic purposes for use in buffaloes. A systematic study of the use of dyes for one-step isolation is necessary.

The present study involves the interactions of these dyes with buffalo luteinizing hormone (LH), a gonadotropin to enable development of a single-step procedure for the purification of this hormone. Normally, the conventional protocol involves the use of several chromatographic separations to attain a homogenous preparation [20, 21]. It is also an effort to elucidate the basic nature of these dyes by analyzing them under various conditions. Cibacron blue has already been used for the purification of buLH [22].

2. Materials and Methods

2.1. Materials

Buffalo pituitary, freshly frozen in liquid nitrogen, was procured from local abattoir. Reactive dye-ligand test kit (RDL-6) was purchased from Sigma (St. Louis, MO, USA), consisting of six dyes: reactive blue 4-agarose, reactive brown 10-agarose, reactive green 19-agarose, reactive red 120-agarose, reactive yellow 86-agarose, and cibacron blue 3GA-agarose. Anti-beta bovine LH antibody was a kind gift from Dr. J. G. Pierce. Goat anti-rabbit HRP conjugate antibody was procured from Bangalore Genie Ltd. 96-well ELISA plates were bought from Greiner, Germany. OPD (orthophenylenediamine) was purchased from Sigma Chemicals. All other reagents used were of analytical grade and were procured locally.

2.2. Method

2.2.1. Preparation of Crude LH (50% Pellet)

Whole pituitary glands of buffaloes of mixed age and sex were procured from the slaughterhouse within 30 minutes of slaughter and kept frozen at −20°C until further processing. The modified protocol of Papkoff as described by Chaudhary and Muralidhar [20] was used for the purification of buLH. The entire extraction process was performed at 4°C, unless otherwise mentioned. The glands were thawed in 0.15 M ammonium sulfate solution containing 1 mM of PMSF (phenyl methyl sulphonyl fluoride). Glands were cut into small pieces and minced followed by homogenization into a thick paste. The pH of homogenate was adjusted to 4.0, using 1 N HCl and then stirred in cold for 1-2 hours. Later, the homogenate was centrifuged at 10,000 g for 20 minutes at 4°C. The pH of the supernatant was adjusted to 3.0 using 0.5 M meta phosphoric acid, stirred for 1-2 hours and centrifuged at 10,000 g for 20 minutes. The pH of the supernatant was finally adjusted to 6.7 using 1 N NaOH. This supernatant was gradually saturated with ammonium sulfate to 50% using a standard nomogram [23], stirred for 2-3 hrs, and ultimately centrifuged at 3000 g for 20 minutes. The entire pellet obtained was dissolved in minimum quantity of distilled water and dialyzed against the same for 40 hrs with frequent changes. Dialyzed material was later lyophilized and stored at −20°C. The 50% ammonium sulfate pellet thereby obtained was used as the starting material for the purification of LH.

2.2.2. Dye-Ligand Affinity Chromatography

The dye-linked agarose gels were allowed to swell in 50 mM phosphate buffer for 48 hours. Two mL columns of immobilized dyes were prepared separately for each dye. Columns were washed extensively with large volumes of equilibrating buffer in order to remove any unbound dye. A flow rate of 20–25 mL/hr was maintained. An amount of 100 μL of a solution of crude buffalo LH (buLH) (50% pellet) of 20 mg/mL in the first buffer was loaded onto each of the columns and incubated for half an hour. All the collected fractions were measured for their absorbance at 280 nm and immunoreactivity using LH specific antiserum. The dye-LH interaction was studied by changing parameters as follows.

2.2.3. Buffer Composition

The columns were washed and equilibrated with 8–10 bed volumes of 50 mM phosphate buffer pH 7.0, and unbound proteins were removed using the same buffer. This was followed by subsequent elution with 80% ethylene glycol and finally 1 M NaCl.

2.2.4. Buffer pH

The columns were washed and equilibrated with 50 mM citrate buffer pH 5.0, and unbound proteins were removed. Elution of the bound protein was executed by varying the pH, that is, by using 50 mM phosphate buffer pH 7.0 and 50 mM sodium glycinate buffer pH 9.0, respectively. Later, 80% ethylene glycol and 1 M NaCl were used.

2.2.5. Buffer Strength

The columns were equilibrated with 25 mM citrate buffer pH 5.0, and unbound proteins were removed. Later, the elution of the bound proteins was done using 50 mM and 100 mM citrate buffer pH 5.0. Subsequent elutions were carried out by increasing the buffer strength of the phosphate buffer pH 7.0 and sodium glycinate buffer pH 9.0 as well to 50 and 100 mM. This was followed by 80% ethylene glycol and 1 M NaCl. In addition, in reactive red dye, 50 mM arginine as a background was introduced in all the steps as an improvement.

2.2.6. Protein Estimation

Proteins were essentially estimated according to the Lowry’s method [24].

2.2.7. ELISA

Direct binding ELISA was used to detect and estimate the quantity of buLH. All the fractions, unbound and bound, were analyzed for their specific LH immunoreactivity using antibeta bovine LH (a kind gift from Dr. J. G. Pierce). The ELISA was essentially performed as described by Arora et al. [21].

All the experiments performed have an average of two results.

3. Results and Discussion

Reactive dyes are known to bind proteins with high affinity but with varying binding capacity and specificity. The chemical composition of most of these reactive dyes is comprised of azo dyes, anthraquinone, or phthalocyanine, linked to a reactive group, often a mono- or dichlorotriazine ring. This unique binding of various proteins to the dyes is still enigmatic and is a multifarious display of electrostatic, hydrophobic hydrogen bonding. [5–7, 25]. To achieve an efficient isolation of desired protein, buLH in our case, it is recommended that the adsorption as well as the elution procedures should carefully be optimized and designed [26]. Hence, elution was performed by addition of competing substance, changing pH or ionic strength, and addition of NaCl [8, 9]. Addition of organic solvents, for example, ethylene glycol, was also used to weaken hydrophobic interactions.

Each dye reflected a distinctive inimitable profile and thus indicated a unique or a predominant character (Figures 1, 2, and 3). The individual results of all the six dyes have been discussed separately keeping into consideration the three figures.

3.1. Cibacron Blue 3GA

3.1.1. Cibacron Exhibited Both Electrostatic, Which Was Predominant, and Hydrophobic Interactions

On changing the nature of the buffers, two isoforms of buLH were eluted using ethylene glycol and NaCl, respectively. About 35% of the bound LH was eluted using 80% ethylene glycol, while 49.5% of it was eluted using 1 M NaCl. This shows that buLH interacts both hydrophobically as well as electrostatically (predominantly) with cibacron [27]. An increase in the pH to 9.0 of the eluting buffer led to the removal of as much as 40% of contaminant nonimmunoreactive proteins. Further, at alkaline pH, there is a weakening of the hydrophobic interactions of the bound LH, thus leading to the release of LH prior to the addition of ethylene glycol. The form of LH, which is eluted subsequently using NaCl, is comparatively the purest form of buLH. Apparently, there is a significant role of electrostatic forces in cibacron-LH binding, which seems to be pH regulated, assisting in making the hydrophobic forces stronger. Changes in ionic strength at varying pH did not have a major impact on the buLH-cibacron interactions; however, it was observed that it played a major role in the binding/removal of nonspecific contaminant proteins.

As per the structure of cibacron, while the presence of three SO₃H groups per molecule is leading to the presence of negative charge thereby promoting electrostatic interactions, the presence of the anthraquinone, diaminobenzene sulphonate, and triazine rings encourages hydrophobic interactions.

3.2. Reactive Blue

3.2.1. Reactive Blue Reflected a Major Electrostatic/Ionic Nature

Reactive blue did not bind buLH as tightly as cibacron. Twenty-four percent of LH was found in the unbound fraction along with the contaminant proteins. Thirty-six percent of bound LH eluted with ethylene glycol and 41% with NaCl. Elution of isoforms with pH and ionic strength were observed with an increase in pH. The interactions of buLH with reactive blue were mainly electrostatic, and any hydrophobic interactions observed are possibly pH dependent and decrease as soon as the pH is increased. Therefore, a change in the ionic strength (25 mM to 100 mM) as well as pH (pH 5 to pH 9) played a crucial role during the elution and resulted in the subsequent emergence of isoforms of buLH.

The structure of reactive blue also contained the anthraquinone ring, the bridging diaminobenzene ring, and the triazine ring; however, unlike cibacron, it was observed that the terminal aminobenzene ring with a sulphonic acid residue was missing thereby leading to a lesser hydrophobic structure as well as more exposure of the charged residue. This increased exposure of the charged residue possibly makes the dye more vulnerable to ionic as well as pH changes.

3.3. Reactive Brown

3.3.1. Reactive Brown, Was Found to Interact with Both Electrostatic and Hydrophobic Groups

With reactive brown, also, like reactive blue, the interactions were found to be mainly electrostatic in nature where the ionic strength and pH played a crucial role in determining the strength of the binding of buLH with the dye. buLH binds to the column quite tightly, and very little was found in the unbound fraction (<20%).While at pH 7.0, 53% of the bound LH was eluted using ethylene glycol and 26% using NaCl, alkaline pH (pH 9.0) conditions led to the weakening of electrostatic interactions, and as much as 44% of the bound LH was eluted out at this pH. However, the change in ionic strength of the buffer had a noteworthy effect, and even at pH 7.0, there was a significant elution of the bound LH with increased ionic strength of 100 mM (35%). Consequently, it is indicative that the hydrophobic character of the dye does not play a pivotal role in the binding of buLH, and most of the major interactions of the hormone with the dye are electrostatic.

The structure of reactive brown reflects that it contained benzoic acid, azo sulphonyl derivative of naphthol, and the triazine ring, besides containing several negatively charged residues like hydroxyl group, chloride group, and the sulphonyl and a keto group. Therefore, there is a prominent negatively charged character and a less strong hydrophobic character. Hence, a change in the pH values can modulate the behavior of the dye.

3.4. Reactive Yellow

3.4.1. Reactive Yellow Indicated a Predominant Ionic Nature

The dye binds to buLH very weakly even at low pH (pH 5.0) and low ionic concentration (25 mM), and consequently a little increase in ionic concentration as well as pH of the buffer leads to the elution of the hormone. Hydrophobic interactions between LH and reactive yellow were found to be very weak in nature. The dye shows a great promise as a buLH single-step purification column because we could achieve more than 50% pure buLH even when the nature of solvent system was altered (Figure 4, Table 2).

The structure of reactive yellow includes disulphonyl naphthalene, acetamide derivative of azo benzene, and triazine ring making an extended conjugated system as evident providing yellow color to the dye.

3.5. Reactive Red

3.5.1. Reactive Red Displayed Hydrophobic Nature

Crude LH bound very tightly to the column at acidic and neutral pH; however, when the pH was made alkaline, elution of buLH was observed. Introduction of salt as well as increase in alkalinity led to the elution of a relatively pure buLH. The structural property of the red dye indicates the presence of six groups and several aromatic ring structures. The presence of bulky ring structure is overshadowing any ionic character it might be possessing.

3.5.2. Use of Arginine

Arginine as a molecule is known to weaken hydrophobic interactions and facilitate elution of bound proteins. Inclusion of arginine in the loading sample has been recognized to increase the recovery of the total protein and decrease the aggregation during ion exchange chromatography [28]. Since arginine solubilizes certain proteins from insoluble pellets in the active, folded structure [29], hydrophobic interaction chromatography in the presence of arginine could be a useful technique for purification of the proteins without potential denaturation [30]. Arginine is an effective additive for the gel permeation columns (GPCs) mobile phase [31–33] as it improves separation of the proteins and their soluble aggregates from the GPC.

Because of the inability to use organic solvents (organic solvents led to the leaching of the dye from the gel) with this dye to weaken the hydrophobic interactions, arginine was used which facilitated the elution of bound proteins, thereby increasing the recovery of the total protein [33, 34]. Addition of arginine (200 mM) at pH 5.0 led to the release of only contaminant proteins, while buLH remained bound to the column. Thereafter, increase in pH and 1 M NaCl led to release of bound hormone. Red dye bound LH very tightly, and this feature was not seen in any other dye.

3.6. Reactive Green

3.6.1. Reactive Green Has a Predominant Hydrophobic Nature

When the nature of the buffers was changed, ethylene glycol leads to the maximum release of the bound LH (55%) compared to the unbound (12.5%) and the NaCl (20%) fractions, thereby suggesting the presence of a strong hydrophobic character on the dye matrix. Alkaline pH of the eluting buffer led to a drastic decrease in the hydrophobic peak (30%), and a considerable amount of LH was eluted using pH 9.0 buffer. A significant effect of the increased pH on the hydrophobicity of the protein as well as the dye has been observed.

The structure of the reactive green shows a large, bulky structure with six groups and several ring structures, which are introducing a large hydrophobic character to the dye. The presence of this bulky ring structure is overcoming any ionic character it might be possessing. The dye matrix is predominantly behaving like a hydrophobic matrix.

3.7. Quantitative Analysis of the Various Eluted “LH” Fractions

Quantitative elution of the loaded protein was observed to decrease in the following order: reactive yellow > cibacron blue 3GA > reactive blue > reactive brown > reactive green. Reactive red and reactive green were found to be strongly hydrophobic, and even strong eluants like ethylene glycol and sodium chloride could not elute out the bound proteins completely (Table 1). Reactive red is an unusual dye in many ways as initially on changing the nature of buffers, no elution was observed, and the dye even leached out following the use of ethylene glycol. Thereby, 1 M urea was subsequently used for the elution of hydrophobic forms. The change in the pH and ionic strength improved the overall elution of the bound proteins except in the case of reactive red dyes. Subsequently, addition of arginine radically improved the elution of the bound protein from the reactive red dye (Table 1).

Purified buLH was used as the reference standard to estimate the immunoreactive buLH content in various dye purified fractions. The ratio of the approximate amount of buLH, as well as various dye purified fractions which are required to achieve an A₄₉₀ of one using antibeta bovine LH, was used as the criteria to estimate the buLH content in them. Subsequently, the fold purification was calculated using the following formula:

Hence, reactive yellow was able to provide us 50-fold purification in a single step (reactive yellow NaCl fraction (Y3)) followed by reactive yellow unbound fraction (Y1) which was 24-fold purified. Besides this, cibacron blue 3GA and reactive blue NaCl fractions are the ones which are promising in nature and can further be exploited for single-step purification (Figure 4, Table 2).

3.8. Optimization of pH for the Loading of the Sample

For determining the optimum pH at which LH binds efficiently to the agarose-bound dye columns, unbound fractions of each of them were assessed for immunoreactivity against buLH. The LH immunoreactivity (A₄₉₀) and the absorbance at 280 nm in various unbound fractions of different dyes at varying pH conditions were plotted (Figure 5). In all the dyes, minimum LH immunoreactivity in the unbound fractions was found at pH 4-5 using citrate buffer, thereby indicating that maximum binding of 50% pellet (crude LH) occurred at the acidic pH.

3.9. Effect of pH on Hydrophobicity

Reaction conditions, such as pH, ionic strength, temperature, and solution components, are known to influence the surface characteristics of the cells like Giardia cysts and Cryptosporidium oocysts [35, 36], especially the surface charge and hydrophobicity. The structure of proteins is primarily affected by hydrophobic, steric, and electrical parameters. Among these factors, hydrophobicity is known to be significantly related to the functional properties of proteins [37].

pH is a predominant factor assisting the hydrophobicity of the dye as well as the proteins [38]. In all of the dye-protein interactions, there is a significant decrease in hydrophobicity observed with a concomitant rise in pH. Therefore, there is an appreciable reduction in all the ethylene glycol fractions when the pH of the buffer is increased from 7.0 to 9.0 (Figure 6). Low pH assists in the binding of proteins. Ionic strength plays a crucial role in isolation of isoforms especially in reactive blue, cibacron blue, reactive red in the presence of arginine, and reactive yellow especially at low pH.

4. Conclusions

The study illustrates that the triazine dyes are not only excellent group-specific ligands but exhibit a wide range of interactions, thereby making the binding of these dyes to proteins highly structure dependent [39]. Strongly coordinating and specific, interactions like hydrogen bonding, van der Waals force, electrostatic force and hydrophobic interaction [40–43] are responsible for the molecular recognition [5, 13, 44] and occur at the natural ligand-binding site of the protein. The dyes offered different characteristics depending upon the cumulative effect of the number of benzene rings (predominant), sulphonate groups, and other ionic groups attached to them despite the fact that all of them have a basic triazine nucleus. An increase in the number of benzene rings beyond five led to the introduction of hydrophobic character to the dye. In fact, a higher number of benzene rings even masked the electrostatic effect of the various ionic groups. Arginine as a molecule was found to be useful in loosening the hydrophobic interactions especially with the red dye. Many of these dyes exhibited a potential of development of single-step purification for the buLH hormone.

Acknowledgments

This paper was supported by grants from UGC Postdoctoral Fellowship for women and DST Women Scientist Scheme, Government of India, New Delhi to T. Arora. Funds and facilities provided by University of Delhi are also gratefully acknowledged.

References

C. R. Lowe, “An introduction to affinity chromatography,” in Laboratory Techniques in Bio-Chemistry and Molecular Biology, T. S. Work and E. Work, Eds., chapter 7, pp. 269–522, North-Holland Biomedical Press, Amsterdam, The Netherlands, 1979.
View at: Google Scholar
C. R. Lowe, D. A. P. Small, and A. Atkinson, “Some preparative and analytical applications of triazine dyes,” International Journal of Biochemistry, vol. 13, no. 1, pp. 33–40, 1981.
View at: Google Scholar
P. D. G. Dean and D. H. Watson, “Protein purification using immobilised triazine dyes,” Journal of Chromatography A, vol. 165, no. 3, pp. 301–319, 1979.
View at: Google Scholar
G. Raya-Tonetti and N. I. Perotti, “Rapid screening of textile dyes employed as affinity ligands to purify enzymes from yeast,” Biotechnology and Applied Biochemistry, vol. 29, no. 2, pp. 151–156, 1999.
View at: Google Scholar
R. K. Scopes, “Dye-ligands and multifunctional adsorbents: an empirical approach to affinity chromatography,” Analytical Biochemistry, vol. 165, no. 2, pp. 235–246, 1987.
View at: Google Scholar
Y. Kroviarski, S. Cochet, C. Vadon, A. Truskolaski, P. Boivin, and O. Bertrand, “Purification of human 6-phosphogluconate dehydrogenase from human haemolysate with chromatography on an immobilized dye as the essential step and use of automation. Simultaneous purification of lactate dehydrogenase,” Journal of Chromatography, vol. 449, no. 2, pp. 413–422, 1988.
View at: Google Scholar
H. Mottl and W. Keck, “Rapid screening of a large number of immobilized textile dyes for the purification of proteins: use of penicillin-binding protein 4 of Escherichia coli as a model enzyme,” Protein Expression and Purification, vol. 3, no. 5, pp. 403–409, 1992.
View at: Google Scholar
M. J. Dunn, “Electroelution of proteins from polyacrylamide gels,” in Methods in Molecular Biology: Protein Purification Protocols, S. Doonan, Ed., pp. 357–362, Humana Press, Totowa, NJ, USA, 1996.
View at: Google Scholar
F. Qadri and P. D. G. Dean, “The use of various immobilized-triazine affinity dyes for the purification of 6-phosphogluconate dehydrogenase from Bacillus stearothermophilus,” Biochemical Journal, vol. 191, no. 1, pp. 53–62, 1980.
View at: Google Scholar
I. Roy and M. N. Gupta, “Purification of alkaline phosphatase from chicken intestine by expanded-bed affinity chromatography on dye-linked cellulose,” Biotechnology and Applied Biochemistry, vol. 32, no. 2, pp. 81–87, 2000.
View at: Google Scholar
P. Bailon, G. K. Ehrlich, W. J. Fung, and W. Berthold, Eds., Affinity Chromatography: Methods and Protocols, vol. 147, Humana Press, Totowa, NJ, USA, 2000.
R. Haeckel, B. Hess, W. Lauterborn, and K. H. Wüster, “Purification and allosteric properties of yeast pyruvate kinase,” Biological Chemistry, vol. 349, no. 5, pp. 699–714, 1968.
View at: Google Scholar
G. Kopperschläger, R. Freyer, W. Diezel, and E. Hofmann, “Some kinetic and molecular properties of yeast phosphofructokinase,” FEBS Letters, vol. 1, no. 3, pp. 137–141, 1968.
View at: Google Scholar
Y. D. Clonis, “Affinity chromatography matures as bioinformatic and combinatorial tools develop,” Journal of Chromatography A, vol. 1101, no. 1-2, pp. 1–24, 2006.
View at: Publisher Site | Google Scholar
K. Mondal and M. N. Gupta, “The affinity concept in bioseparation: evolving paradigms and expanding range of applications,” Biomolecular Engineering, vol. 23, no. 2-3, pp. 59–76, 2006.
View at: Publisher Site | Google Scholar
I. Y. Galaev and B. Mattiasson, “Shielding affinity chromatography,” Nature Biotechnology, vol. 12, no. 11, p. 1086, 1994.
View at: Google Scholar
I. Y. Galaev, C. Warrol, and B. Mattiasson, “Temperature-induced displacement of proteins from dye-affinity columns using an immobilized polymeric displacer,” Journal of Chromatography A, vol. 684, no. 1, pp. 37–43, 1994.
View at: Publisher Site | Google Scholar
B. Champluvier and M. R. Kula, “Dye-ligand membranes as selective adsorbents for rapid purification of enzymes: a case study,” Biotechnology and Bioengineering, vol. 40, no. 1, pp. 33–40, 1992.
View at: Publisher Site | Google Scholar
J. G. Pierce and T. F. Parsons, “Glycoprotein hormones: structure and function,” Annual Review of Biochemistry, vol. 50, pp. 465–495, 1981.
View at: Google Scholar
R. Chaudhary and K. Muralidhar, “Use of SP-sephadexto fractionate and obtain semi-pure preparation from whole pituitaries of Indian water buffaloes (Bubalus bubalis),” Preparative Biochemistry and Biotechnology, vol. 34, no. 4, pp. 315–329, 2004.
View at: Publisher Site | Google Scholar
T. Arora, N. Vashistha, and K. Muralidhar, “Chromatographic separation of thyroid stimulating hormone from luteinizing hormone,” Journal of Liquid Chromatography and Related Technologies, vol. 33, no. 5, pp. 680–692, 2010.
View at: Publisher Site | Google Scholar
R. Chaudhary, S. Jain, K. Muralidhar, and M. N. Gupta, “Purification of bubaline luteinizing hormone by gel filtration chromatography in the presence of blue dextran,” Process Biochemistry, vol. 41, no. 3, pp. 562–566, 2006.
View at: Publisher Site | Google Scholar
M. Dixon, “A nomogram for ammonium sulphate solutions,” The Biochemical Journal, vol. 54, no. 3, pp. 457–458, 1953.
View at: Google Scholar
O. H. Lowry, N. J. Rosebrough, A. L. Farr, and R. J. Randall, “Protein measurement with the Folin phenol reagent,” The Journal of Biological Chemistry, vol. 193, no. 1, pp. 265–275, 1951.
View at: Google Scholar
R. K. Scopes, “Strategies for enzyme isolation using dye-ligand and related adsorbents,” Journal of Chromatography—Biomedical Applications, vol. 376, pp. 131–140, 1986.
View at: Google Scholar
A. Denizli and E. Pişkin, “Dye-ligand affinity systems,” Journal of Biochemical and Biophysical Methods, vol. 49, no. 1–3, pp. 391–416, 2001.
View at: Publisher Site | Google Scholar
T. Arora, N. Vashistha, R. Chaudhary, and K. Muralidhar, “Pseudo-affinity chromatographic approach to probe heterogeneity in buffalo pituitary luteinizing hormone: probable pseudolectin-like behavior of immobilized Cibacron Blue 3GA,” Journal of Chromatography B, vol. 878, no. 28, pp. 2679–2684, 2010.
View at: Publisher Site | Google Scholar
T. Arakawa, K. Tsumoto, K. Nagase, and D. Ejima, “The effects of arginine on protein binding and elution in hydrophobic interaction and ion-exchange chromatography,” Protein Expression and Purification, vol. 54, no. 1, pp. 110–116, 2007.
View at: Publisher Site | Google Scholar
M. Umetsu, K. Tsumoto, S. Nitta et al., “Nondenaturing solubilization of β2 microglobulin from inclusion bodies by L-arginine,” Biochemical and Biophysical Research Communications, vol. 328, no. 1, pp. 189–197, 2005.
View at: Publisher Site | Google Scholar
T. Arakawa, D. Ejima, K. Tsumoto, M. Ishibashi, and M. Tokunaga, “Improved performance of column chromatography by arginine: dye-affinity chromatography,” Protein Expression and Purification, vol. 52, no. 2, pp. 410–414, 2007.
View at: Publisher Site | Google Scholar
D. Ejima, R. Yumioka, T. Arakawa, and K. Tsumoto, “Arginine as an effective additive in gel permeation chromatography,” Journal of Chromatography A, vol. 1094, no. 1-2, pp. 49–55, 2005.
View at: Publisher Site | Google Scholar
G. K. Ackers and T. E. Thompson, “Determination of stoichiometry and equilibrium constants for reversibly associating systems by molecular sieve chromatography,” Proceedings of the National Academy of Sciences of the United States of, vol. 53, pp. 342–349, 1965.
View at: Google Scholar
M. Li, Z. G. Su, and J. C. Janson, “In vitro protein refolding by chromatographic procedures,” Protein Expression and Purification, vol. 33, no. 1, pp. 1–10, 2004.
View at: Publisher Site | Google Scholar
T. S. Work and E. Work, Eds., Techniques in Biochemistry and Molecular Biology, North-Holland, Amsterdam, The Netherlands.
K. Ohmori and C. E. Glatz, “Effects of pH and ionic strength on microfiltration of C. glutamicum,” Journal of Membrane Science, vol. 153, no. 1, pp. 23–32, 1999.
View at: Publisher Site | Google Scholar
B. M. Hsu and C. Huang, “Influence of ionic strength and pH on hydrophobicity and zeta potential of Giardia and Cryptosporidium,” Colloids and Surfaces A, vol. 201, no. 1-3, pp. 201–206, 2002.
View at: Publisher Site | Google Scholar
S. Nakai, E. Li-Chan, and G. E. Arteaga, “Measurement of surface hydrophobicity,” in Methods of Testing Protein Functionality, G. M. Hall, London, UK, 1996.
View at: Google Scholar
N. Alizadeh-Pasdar and E. C. Y. Li-Chan, “Comparison of protein surface hydrophobicity measured at various pH values using three different fluorescent probes,” Journal of Agricultural and Food Chemistry, vol. 48, no. 2, pp. 328–334, 2000.
View at: Publisher Site | Google Scholar
F. Qadri, “The reactive triazine dyes: their usefulness and limitations in protein purifications,” Trends in Biotechnology, vol. 3, no. 1, pp. 7–12, 1985.
View at: Google Scholar
Y. Yue, X. Chen, J. Qin, and X. Yao, “A study of the binding of C.I. Direct Yellow 9 to human serum albumin using optical spectroscopy and molecular modeling,” Dyes and Pigments, vol. 79, no. 2, pp. 176–182, 2008.
View at: Publisher Site | Google Scholar
S. Y. Suen, S. Y. Lin, and H. C. Chiu, “Effects of spacer arms on Cibacron Blue 3GA immobilization and lysozyme adsorption using regenerated cellulose membrane discs,” Industrial and Engineering Chemistry Research, vol. 39, no. 2, pp. 478–487, 2000.
View at: Google Scholar
C. H. Chen and W. C. Lee, “Affinity chromatography of proteins on non-porous copolymerized particles of styrene, methyl methacrylate and glycidyl methacrylate,” Journal of Chromatography A, vol. 921, no. 1, pp. 31–37, 2001.
View at: Publisher Site | Google Scholar
S. Y. I. Suen and Y. I. D. A. Tsai, “Comparison of ligand density and protein adsorption on dye-affinity membranes using different spacer arms,” Separation Science and Technology, vol. 35, no. 1, pp. 69–87, 1999.
View at: Google Scholar
S. Y. Bi, D. Q. Song, Y. Tian, X. Zhou, Z. Y. Liu, and H. Zhang, “Molecular spectroscopic study on the interaction of tetracyclines with serum albumins,” Spectrochimica Acta A, vol. 61, no. 4, pp. 629–636, 2005.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2012 Taruna Arora et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

2711

Downloads

1225

Citations