Table of Contents
ISRN Tribology
Volume 2013 (2013), Article ID 386861, 9 pages
http://dx.doi.org/10.5402/2013/386861
Research Article

Friction Performance of Al-10%SiCp Reinforced Metal Matrix Composites Using Taguchi Method

Department of Mechanical Engineering, Jadavpur University, Kolkata 700032, India

Received 27 April 2012; Accepted 25 June 2012

Academic Editors: J. Antunes and J. Wang

Copyright © 2013 Shouvik Ghosh et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. M. Bai, Q. Xue, X. Wang, Y. Wan, and W. Liu, “Wear mechanism of SiC whisker-reinforced 2024 aluminum alloy matrix composites in oscillating sliding wear tests,” Wear, vol. 185, no. 1-2, pp. 197–202, 1995. View at Google Scholar · View at Scopus
  2. A. Onat, “Mechanical and dry sliding wear properties of silicon carbide particulate reinforced aluminium-copper alloy matrix composites produced by direct squeeze casting method,” Journal of Alloys and Compounds, vol. 489, no. 1, pp. 119–124, 2010. View at Publisher · View at Google Scholar · View at Scopus
  3. R. Chen, A. Iwabuchi, and T. Shimizu, “The effect of a T6 heat treatment on the fretting wear of a SiC particle-reinforced A356 aluminum alloy matrix composite,” Wear, vol. 238, no. 2, pp. 110–119, 2000. View at Publisher · View at Google Scholar · View at Scopus
  4. H. Ahlatci, E. Candan, and H. Cimenoglu, “Abrasive wear behavior and mechanical properties of Al-Si/SiC composites,” Wear, vol. 257, no. 5-6, pp. 625–632, 2004. View at Publisher · View at Google Scholar · View at Scopus
  5. R. Chen, A. Iwabuchi, T. Shimizu, H. S. Shin, and H. Mifune, “The sliding wear resistance behavior of NiAl and SiC particles reinforced aluminum alloy matrix composites,” Wear, vol. 213, no. 1-2, pp. 175–184, 1997. View at Google Scholar · View at Scopus
  6. Y. Iwai, H. Yoneda, and T. Honda, “Sliding wear behavior of SiC whisker-reinforced aluminum composite,” Wear, vol. 181–183, no. 2, pp. 594–602, 1995. View at Google Scholar · View at Scopus
  7. A. M. Hassan, A. Alrashdan, M. T. Hayajneh, and A. T. Mayyas, “Wear behavior of Al-Mg-Cu-based composites containing SiC particles,” Tribology International, vol. 42, no. 8, pp. 1230–1238, 2009. View at Publisher · View at Google Scholar · View at Scopus
  8. F. Akhlaghi and A. Zare-Bidaki, “Influence of graphite content on the dry sliding and oil impregnated sliding wear behavior of Al 2024-graphite composites produced by in situ powder metallurgy method,” Wear, vol. 266, no. 1-2, pp. 37–45, 2009. View at Publisher · View at Google Scholar · View at Scopus
  9. A. Martín, M. A. Martínez, and J. Llorca, “Wear of SiC-reinforced Al-matrix composites in the temperature range 20–2000°C,” Wear, vol. 193, no. 2, pp. 169–179, 1996. View at Publisher · View at Google Scholar · View at Scopus
  10. M. Bai, Q. Xue, and Q. Ge, “Wear of 2024 Al-Mo-SiC composites under lubrication,” Wear, vol. 195, no. 1-2, pp. 100–105, 1996. View at Google Scholar · View at Scopus
  11. V. S. R. Murthy, K. Srikanth, and C. B. Raju, “Abrasive wear behaviour of SiC whisker-reinforced silicate matrix composites,” Wear, vol. 223, no. 1-2, pp. 79–92, 1998. View at Publisher · View at Google Scholar · View at Scopus
  12. J. Rodríguez, P. Poza, M. A. Garrido, and A. Rico, “Dry sliding wear behaviour of aluminium-lithium alloys reinforced with SiC particles,” Wear, vol. 262, no. 3-4, pp. 292–300, 2007. View at Publisher · View at Google Scholar · View at Scopus
  13. T. Ma, H. Yamaura, D. A. Koss, and R. C. Voigt, “Dry sliding wear behavior of cast SiC-reinforced Al MMCs,” Materials Science and Engineering A, vol. 360, no. 1-2, pp. 116–125, 2003. View at Publisher · View at Google Scholar · View at Scopus
  14. Y. Yalcin and H. Akbulut, “Dry wear properties of A356-SiC particle reinforced MMCs produced by two melting routes,” Materials and Design, vol. 27, no. 10, pp. 872–881, 2006. View at Publisher · View at Google Scholar · View at Scopus
  15. H. Tang, X. Zeng, X. Xiong, L. Li, and J. Zou, “Mechanical and tribological properties of short-fiber-reinforced SiC composites,” Tribology International, vol. 42, no. 6, pp. 823–827, 2009. View at Publisher · View at Google Scholar · View at Scopus
  16. G. Taguchi, Introduction to Quality Engineering, Asian Productivity Organization, 1990.
  17. P. J. Ross, Taguchi Technique for Quality Engineering, McGraw-Hill, New York, NY, USA, 2nd edition, 1996.
  18. R. K. Roy, A Primer on Taguchi Method, Van Nostraid Reinhold, New York, NY, USA, 1990.
  19. R. A. Fisher, Design of Experiments, Oliver & Boyd, Edinburgh, UK, 1951.
  20. Minitab User Manual (Release 13.2), Making Data Analysis Easier, MINITAB, State College, Pa, USA, 2001.