Table of Contents
ISRN Mechanical Engineering
Volume 2013, Article ID 640958, 11 pages
http://dx.doi.org/10.1155/2013/640958
Research Article

Springback Analysis in Sheet Metal Forming Using Modified Ludwik Stress-Strain Relation

Department of Mechanical Engineering, Indian Institute of Technology, Banaras Hindu University, Varanasi 221005, India

Received 18 June 2013; Accepted 17 July 2013

Academic Editors: C. C. Huang and A. Z. Sahin

Copyright © 2013 Sanjay Kumar Patel et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. G. Sachs, Principles and Methods of Sheet Metal Fabricating, Reinhold, New York, NY, USA, 1951.
  2. W. Schroeder, “Mechanics of sheet metal bending,” Transactions of the ASME, vol. 36, pp. 138–145, 1943. View at Google Scholar
  3. F. J. Gardiner, “The springback of metals,” Transactions of the ASEME, vol. 49, pp. 1–9, 1958. View at Google Scholar
  4. A. N. Singh and W. Johnson, “Springback after cylindrically bending metal strips,” in Proceedings of the Dr Karunesh Memorial International Conference, New Delhi, India, December 1979.
  5. J. H. Huth, “A note on plastic torsion,” Journal of Applied Mechanics, vol. 22, pp. 432–434, 1955. View at Google Scholar
  6. A. Nadai, Theory of Flow and Fracture of Solids, vol. 1, McGraw-Hill, 1950.
  7. P. C. Upadhyay, Elasto-plastic torsion [M.Tech. thesis], Mechanical Engineering Department, I.I.T. Kanpur, 1970.
  8. J. P. Dwivedi, A. N. Singh, S. Ram, and N. K. Das Talukder, “Springback analysis in torsion of rectangular strips,” International Journal of Mechanical Sciences, vol. 28, no. 8, pp. 505–515, 1986. View at Google Scholar · View at Scopus
  9. J. P. Dwivedi, P. K. Sarkar, R. S. Ram. S., N. K. D. Talukder, and A. N. Singh, “Experimental aspects of torsional springback in rectangular strips,” Journal of the Institution of Engineers, vol. 67, no. 4, pp. 70–73, 1987. View at Google Scholar · View at Scopus
  10. J. P. Dwivedi, A. K. Shukla, and P. C. Upadhyay, “Torsional springback of square section bars of linear wor hardening materials,” Computers and Structures, vol. 45, no. 3, pp. 421–429, 1972. View at Google Scholar · View at Scopus
  11. J. P. Dwivedi, P. C. Upadhyay, and N. K. Das Talukder, “Torsional springback in square section bars of nonlinear work-hardening materials,” International Journal of Mechanical Sciences, vol. 32, no. 10, pp. 863–876, 1990. View at Google Scholar · View at Scopus
  12. J. P. Dwivedi, P. C. Upadhyay, and N. K. D. Talukder, “Springback analysis of torsion of L-sectioned bars of work-hardening materials,” Computers and Structures, vol. 43, no. 5, pp. 815–822, 1992. View at Google Scholar · View at Scopus
  13. Z. T. Zhang and S. J. Hu, “Stress and residual stress distributions in plane strain bending,” International Journal of Mechanical Sciences, vol. 40, no. 6, pp. 533–543, 1998. View at Google Scholar · View at Scopus
  14. T. Kuwabara, “Advances in experiments on metal sheets and tubes in support of constitutive modeling and forming simulations,” International Journal of Plasticity, vol. 23, no. 3, pp. 385–419, 2007. View at Publisher · View at Google Scholar · View at Scopus
  15. H. K. Yi, D. W. Kim, C. J. van Tyne, and Y. H. Moon, “Analytical prediction of springback based on residual differential strain during sheet metal bending,” Journal of Mechanical Engineering Science, vol. 222, no. 2, pp. 117–129, 2008. View at Publisher · View at Google Scholar · View at Scopus
  16. A. El Megharbel, G. A. El Nasser, and A. El Domiaty, “Bending of tube and section made of strain-hardening materials,” Journal of Materials Processing Technology, vol. 203, no. 1–3, pp. 372–380, 2008. View at Publisher · View at Google Scholar · View at Scopus
  17. E. Da-xin, H. Hau-hui, L. Xiao-yi, and N. Ru-xin, “Spring-back deformation in tube bending,” International Journal of Minerals, Metallurgy and Materials, vol. 16, no. 2, pp. 177–183, 2009. View at Publisher · View at Google Scholar · View at Scopus
  18. D. E. Daxin E and Y. Liu, “Springback and time-dependent springback of 1Cr18Ni9Ti stainless steel tubes under bending,” Materials and Design, vol. 31, no. 3, pp. 1256–1261, 2010. View at Publisher · View at Google Scholar · View at Scopus
  19. V. K. Choubey, M. Gangwar, and J. P. Dwivedi, “Torsional springback analysis in thin tubes with non-linear work hardening,” Journal of Mechanical Engineering, vol. 7, no. 1, pp. 15–34, 2011. View at Google Scholar
  20. V. K. Choubey, M. Gangwar, and J. P. Dwivedi, “Springback analysis of thin tubes,” Journal of Mechanical Engineering, vol. 7, no. 2, 2011. View at Google Scholar
  21. V. K. Choubey, M. Gangwar, J. P. Dwivedi, and N. K. das Talukder, “Springback analysis of thin tubes with arbitrary stress-strain curves,” Journal of Mechanical Engineering, vol. 8, no. 1, 2011. View at Google Scholar