Table of Contents
International Scholarly Research Notices
Volume 2014 (2014), Article ID 607272, 11 pages
http://dx.doi.org/10.1155/2014/607272
Research Article

Fatigue Life Assessment of 65Si7 Leaf Springs: A Comparative Study

1Department of Engineering, NIFTEM, HSIIDC, Kundli, Haryana 131028, India
2Department of Mechanical Engineering, National Institute of Technology, Kurukshetra, Haryana 136019, India
3Department of Mechanical Engineering, YMCA University of Science & Technology, Faridabad, Haryana 121006, India

Received 1 July 2014; Revised 28 August 2014; Accepted 28 August 2014; Published 29 October 2014

Academic Editor: T. Y. Kam

Copyright © 2014 Vinkel Kumar Arora et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. S. Saelem, S. Chantranuwathana, K. Panichanun, P. Preedanood, P. Wichienprakarn, and P. Kruo-ongarjnukool, “Experimental verification of leaf spring model by using a leaf spring test rig,” in Proceedings of the 23rd Conference of the Mechanical Engineering Network of Thailand, Chiang Mai, Thailand, November 2009.
  2. F. N. A. Refngah, S. Abdullah, A. Jalar, and L. B. Chua, “Fatigue life evaluation of two types of steel leaf springs,” International Journal of Mechanical and Materials Engineering, vol. 4, no. 2, pp. 136–140, 2009. View at Google Scholar · View at Scopus
  3. J. J. Fuentes, H. J. Aguilar, J. A. Rodríguez, and E. J. Herrera, “Premature fracture in automobile leaf springs,” Engineering Failure Analysis, vol. 16, no. 2, pp. 648–655, 2009. View at Publisher · View at Google Scholar · View at Scopus
  4. M. L. Aggarwal, R. A. Khan, and V. P. Aggarwal, “Optimization of micro welds used in the leaf springs,” International Journal of Engineering Material and Science, vol. 28, pp. 217–220, 2006. View at Google Scholar
  5. M. L. Aggarwal, V. P. Agrawal, and R. A. Khan, “A stress approach model for predictions of fatigue life by shot peening of EN45A spring steel,” International Journal of Fatigue, vol. 28, no. 12, pp. 1845–1853, 2006. View at Publisher · View at Google Scholar · View at Scopus
  6. M. M. Patunkar and D. R. Dolas, “Modelling and analysis of composite leaf spring under the static load condition by using FEA,” International Journal of Mechanical & Industrial Engineering, vol. 1, no. 1, pp. 1–4, 2011. View at Google Scholar
  7. M. S. Kumar and S. Vijayarangan, “Analytical and experimental studies on fatigue life prediction of steel and composite multi-leaf spring for light passenger vehicles using life data analysis,” Materials Science, vol. 13, no. 2, pp. 141–146, 2007. View at Google Scholar
  8. P. Sanjurjo, C. Rodríguez, I. F. Pariente, F. J. Belzunce, and A. F. Canteli, “The influence of shot peening on the fatigue behaviour of duplex stainless steels,” Procedia Engineering, vol. 2, no. 1, pp. 1539–1546, 2010. View at Publisher · View at Google Scholar
  9. W. Z. Zhuang and G. R. Halford, “Investigation of residual stress relaxation under cyclic load,” International Journal of Fatigue, vol. 23, supplement 1, pp. S31–S37, 2001. View at Publisher · View at Google Scholar · View at Scopus
  10. G. Savaidis, M. Malikoutsakis, and A. Savaidis, “FE simulation of vehicle leaf spring behavior under driving manoeuvres,” International Journal of Structural Integrity, vol. 4, no. 1, Article ID 17082873, pp. 23–32, 2013. View at Publisher · View at Google Scholar · View at Scopus
  11. IS 1135, Springs—Leaf Springs Assembly for Automobiles, 1995.
  12. SAE, Spring Design Manual—Design and Application of Leaf Springs, HS-744, AE-11, 1990.
  13. R. L. Norton, Machine Design—An Integrated Approach, Pearson Education, Asia, 2nd edition, 2001.
  14. “Ansys Workbench training manual on fatigue tool,” 2014.