A Platoon Dispersion Model Based on a Truncated Normal Distribution of Speed

Abstract

Understanding platoon dispersion is critical for the coordination of traffic signal control in an urban traffic network. Assuming that platoon speed follows a truncated normal distribution, ranging from minimum speed to maximum speed, this paper develops a piecewise density function that describes platoon dispersion characteristics as the platoon moves from an upstream to a downstream intersection. Based on this density function, the expected number of cars in the platoon that pass the downstream intersection, and the expected number of cars in the platoon that do not pass the downstream point are calculated. To facilitate coordination in a traffic signal control system, dispersion models for the front and the rear of the platoon are also derived. Finally, a numeric computation for the coordination of successive signals is presented to illustrate the validity of the proposed model.

1. Introduction

At an intersection, lights change from red to green permitting drivers to proceed straight through the intersection. On urban roads these cars will be traveling at different speeds. While moving downstream, the platoon spreads out in a long segment and cars do not uniformly arrive at the next intersection; this is called platoon dispersion. As a platoon moves downstream from an upstream intersection at green phase end time, the cars in the platoon become segmented due to compression and splitting at the downstream intersection’s signal lights. It is obvious that using platoon dispersion theory to optimize signal timing plans for traffic signal control could effectively reduce the number of stops and thereby lead to a sharp decline in pollution emissions and fuel consumption.

However, platoon dispersion makes signal coordination more complicated [1–17]. Previous studies on the diffusion of traffic platoons have adopted one of three standard approaches: the wave theory of Lighthill and Whitham [1–3], Pacey’s diffusion theory [4–9], and Robertson’s recursive platoon dispersion model [10–12]. The first model, also called the LWR model in the literature of traffic flow theory, needs to have an accurate representation of the equilibrium flow-density relationship, which makes it unsuitable for practical applications [13]. The second approach firstly proposes a purely kinematical model to describe the diffusion of traffic platoons by assuming that the speed of traffic follows a normal distribution [4]. Its invalid input parameters (viz. the average speed of vehicles and standard deviation of speed) to calibrate the model make it suitable only for the study of small changes in traffic cycles [6]. The final model uses field data to derive an empirical method for predicting platoon behavior and has been widely used in the well-known TRANSYT software model, because of its simplicity and good explanatory power for understanding the qualitative behavior of road traffic [12]. Both Pacey’s and Robertson’s models are probability-based models with different probability density functions. Seddon [14, 15] concluded in his series of studies on different models of platoon dispersion that there is little difference between the Pacey and Robertson methods with regards to accuracy or efficiency. However, a study by Wang et al. [16] concluded that the recursive model gives good results for short distances, while models using lognormal and normal distributions are better for longer distances.

As mentioned previously, Pacey’s model is the most successful combination of theoretical and experimental work on traffic platoons. Most current research based on this model assumes that platoon speed follows a normal distribution, spreading from negative infinity to positive infinity. This does not properly reflect the field situation. Grace and Potts [5] further investigated the density aspect of Pacey’s model. Liu and Yang [6–8] proposed a method to correct the vehicle startup time loss of Grace’s model. Wang et al. [9] also further refined Pacey’s model by considering travel time following a nontransformed normal distribution.

To address the defects of Pacey’s model, the authors of this paper propose a more realistic platoon dispersion model, which assumes that the velocity of cars follows a truncated normal distribution, ranging from a minimum speed to a maximum speed [17]. On the basis of the authors’ previous research, this paper analyzes platoon dispersion characteristics as the platoon moves down from an upstream intersection at green phase end time. Finally, numeric computation applying the model to signal coordination is presented to confirm the model’s validity.

2. Platoon Dispersion Model

2.1. Assumptions of the Speed Density Function

In Pacey’s model, the cars in a platoon are assumed to move with unchanged speeds (i.e., it is ideally treated as the average speed of vehicles measured between adjacent intersections). It is assumed that (a) all the vehicles behind the stop lines uniformly start up after the signal turns from red to green, (b) a car’s speed is independent of its position in a platoon, and (c) there is no interaction between cars and a faster car can pass a slower one without hindrance.

A definite value is assigned to the probability that certain cars will have positive speed. Pacey’s research has proven that car speeds in a platoon are normally distributed with mean 𝜇 and variance 𝜎², which accounts for the spread of platoons. However, the proportion of cars with 𝑣<𝑣_𝑚 and 𝑣>𝑣_𝑓 is zero in reality (𝑣_𝑚 and 𝑣_𝑓 denote minimum speed and maximum speed, resp.). Hence, a speed range in a truncated normal distribution extending from 𝑣_𝑚 to 𝑣_𝑓 is a much more reasonable assumption. In this case, the speed density function is as follows:𝑓^(𝑣)=⎧⎪⎨⎪⎩𝑐√21𝜋𝜎𝑒^{−0.5((𝑣−𝜇)/𝜎)2}0,,𝑣ot_𝑚he≤rs𝑣.≤𝑣_𝑓,(2.1)

Its calculation formula can be expressed as follows:(a)for 𝑣<𝑣_𝑚∶𝐹^′(𝑣)=∫^𝑣𝑚_−∞𝑓^(𝑣)𝑑𝑥=0;(b)for 𝑣_𝑚≤𝑣≤𝑣_𝑓∶𝐹^(𝑣)=∫^𝑣−∞𝑓^(𝑣)𝑑𝑥=∫^𝑣𝑣_𝑚𝑓^(𝑣)𝑑𝑥=𝑐[∫^𝑣−∞(1/(√2𝜋𝜎))𝑒^{−0.5((𝑣−𝜇)/𝜎)2}𝑑𝑥− ∫^𝑣𝑚_−∞(1/(√2𝜋𝜎))𝑒^{−0.5((𝑣−𝜇)/𝜎)2}𝑑𝑥]=𝑐[𝐹(𝑣)−𝐹(𝑣_𝑚)];(c)for 𝑣>𝑣_𝑓∶𝐹^(𝑣)=∫^𝑣𝑣_𝑚𝑓^(𝑣)𝑑𝑥=∫^𝑣𝑓_𝑣𝑚𝑓^(𝑣)𝑑𝑥=𝑐[𝐹(𝑣_𝑓)−𝐹(𝑣_𝑚)]=1.

As the constant 𝑐 ensures that the accumulated probability of 𝑓^(𝑣) in the range [𝑣_𝑚,𝑣_𝑓] equals 1, then 1/𝑐=𝐹(𝑣_𝑚≤𝑣≤𝑣_𝑓)=𝜙(𝑣_𝑓/𝜎−𝜇/𝜎)−𝜙(𝑣_𝑚/𝜎−𝜇/𝜎).

2.2. Development of the Platoon Dispersion Model

Assuming that the start time of the upstream signal green phase 𝑡 equals 0, and the stop bar location 𝑥 is 0, then the initial density distribution function 𝑘(𝑥,0) of the queuing vehicles behind the stop bar at time 𝑡=0 is𝑘(𝑥,0)=⎧⎪⎨⎪⎩0𝑘0,,,−𝑥𝑥𝑎≥<≤−0,_𝑗𝑥𝑎,≤0,(2.2) where 𝑎 is the queue length and 𝑘_𝑗 is the jam density within the queue length.

This paper studies the movement of a platoon from the beginning of a green phase, until it passes a downstream intersection. As illustrated in Figure 1, the queuing vehicles at the upstream intersection start traveling at constant speed 𝑣 from their stop position 𝑥−𝑣𝑡∈[−𝑎,0] at the start time of the green phase 𝑡=0. After time 𝑡, the number of vehicles having passed the downstream intersection (real or virtual) and the number that have not past the downstream intersection are 𝐴(𝑥,𝑡) and 𝐵(𝑥,𝑡), respectively. The computation formula is derived according to the aforementioned physical definition and presented as follows:𝐵(𝑥,𝑡)=𝐴𝑘(_𝑗𝑥,𝑡)=^{𝑡⋅𝑣𝑓}_𝑥𝑘(𝑦,𝑡)𝑑𝑦,𝑎−𝐴(𝑥,𝑡)=^𝑥𝑡𝑣_𝑚−𝑎𝑘(𝑦,𝑡)𝑑𝑦,(2.3) where 𝑘(𝑦,𝑡) is the density of the platoon past 𝑦 at time 𝑡. The density distribution function 𝑘(𝑥,𝑡), at downstream location 𝑥 at time 𝑡, is calculated using the following piecewise function:𝑘(𝑥,𝑡)=^𝑣𝑓_𝑣𝑚𝑓^(𝑣)𝑘(𝑥−𝑣𝑡,0)𝑑𝑣=⎧⎪⎪⎪⎪⎪⎨⎪⎪⎪⎪⎪⎩0,𝑥>𝑡𝑣^𝑓𝑘∨𝑥<𝑡𝑣_𝑚−𝑎,_𝑗^{𝑣𝑥/𝑡+𝑎/𝑡}_𝑚𝑘_𝑗𝑓^(𝑣)𝑑𝑣,𝑡𝑣_𝑚−𝑎≤𝑥<𝑡𝑣_𝑚,^{𝑥/𝑡+𝑎/𝑡𝑥/𝑡}𝑘𝑓^(𝑣)𝑑𝑣,𝑡𝑣_𝑚≤𝑥≤𝑡𝑣_𝑓−𝑎,_𝑗^𝑣𝑓_𝑥/𝑡𝑓^(𝑣)𝑑𝑣,𝑡𝑣_𝑓−𝑎<𝑥≤𝑡𝑣_𝑓.(2.4)

Figure 1 

Spreading of platoon.

Let 𝑢=(𝑣−𝜇)/𝜎, and the variation coefficient 𝛼=𝜎/𝜇, as follows:^𝑣2_𝑣1𝑓^(𝑣)𝑑𝑣=𝑐^{(𝑣2−𝜇)/𝜎(𝑣}_{1−𝜇)/𝜎}1√2𝜋𝑒^−0.5𝑢2𝑑𝑢=𝑐^{(𝑡𝑣2/𝜇−𝑡)/𝛼𝑡(𝑡𝑣}_{1/𝜇−𝑡)/𝛼𝑡}1√2𝜋𝑒^−0.5𝑢2𝑑𝑢=𝑐2[𝐹(𝑧)]^𝑧2𝑧1,(2.5) where 𝑧₂=(𝑡𝑣₂/𝜇−𝑡)/√2𝛼𝑡, 𝑧₁=(𝑡𝑣₁/𝜇−𝑡)/√2𝛼𝑡, 𝑣₁ and 𝑣₂ are constants, and 𝐹(𝑧)=2∫^√02𝑧(1/√2𝜋)𝑒^−0.5𝑢2𝑑𝑢=(2/√𝜋)∫^𝑧0𝑒^−𝑢2𝑑𝑢 is the standard normal distribution.

Following (2.4) and (2.5), the calculation formula of 𝑘(𝑥,𝑡) is as follows:𝑘(𝑥,𝑡)=⎧⎪⎪⎪⎪⎨⎪⎪⎪⎪⎩0,𝑥>𝑡𝑣^𝑓𝑐𝑘_𝑗∨𝑥<𝑡𝑣_𝑚−𝑎,2[𝐹(𝑧)]^{√(𝑥/𝜇+𝑎/𝜇−𝑡)/2𝛼𝑡(𝑡𝑣}_𝑚^{√/𝜇−𝑡)/2𝛼𝑡}𝑐𝑘_𝑗,𝑡𝑣_𝑚−𝑎≤𝑥<𝑡𝑣_𝑚,2[𝐹(𝑧)]^{√(𝑥/𝜇+𝑎/𝜇−𝑡)/√2𝛼𝑡(𝑥/𝜇−𝑡)/2𝛼𝑡}𝑐𝑘_𝑗,𝑡𝑣_𝑚≤𝑥≤𝑡𝑣_𝑓−𝑎,2[𝐹(𝑧)]^{(𝑡𝑣𝑓√/𝜇−𝑡)/√2𝛼𝑡(𝑥/𝜇−𝑡)/2𝛼𝑡},𝑡𝑣_𝑓−𝑎<𝑥≤𝑡𝑣_𝑓.(2.6)

Let 𝐺(𝑧)=∫𝐹(𝑧)𝑑𝑧=𝑧𝐹(𝑧)+(1/√𝜋)exp(−𝑧²); then, based on (2.6), the number of vehicles ∫^𝑥2_𝑥1𝑘(𝑦,𝑡)𝑑𝑦 distributed along the road segment [𝑥₁,𝑥₂] can be calculated as follows: ^𝑥2_𝑥1𝑘(𝑦,𝑡)𝑑𝑦=𝑐⋅𝑘^𝑗2^𝑥2_𝑥1𝐹𝑧₂=𝑐𝑘_𝑗(𝑦)−𝐹𝑧₁(𝑦)𝑑𝑦𝜇√2𝛼𝑡2^{𝑧2(𝑥2)𝑧}_2𝑥1=𝑐𝑘_𝑗𝐹(𝑦)𝑑𝑦−^{𝑧1(𝑥2)𝑧}_1𝑥1𝐹(𝑦)𝑑𝑦𝜇√2𝛼𝑡2[𝐺(𝑧)]^{𝑧2(𝑥2)𝑧2𝑥1}−[𝐺(𝑧)]^{𝑧1(𝑥2)𝑧}_1𝑥1.(2.7)

Using (2.6) and (2.7), 𝐴(𝑥,𝑡) and 𝐵(𝑥,𝑡) can be calculated under the following five scenarios:(a)for 𝑥>𝑡𝑣_𝑓∶𝐴(𝑥,𝑡)=0 and 𝐵(𝑥,𝑡)=∫^{𝑡⋅𝑣𝑚}_{𝑡⋅𝑣𝑚−𝑎}𝑘(𝑦,𝑡)𝑑𝑦+∫^{𝑡⋅𝑣𝑓−𝑎𝑡⋅𝑣}_𝑚𝑘(𝑦,𝑡)𝑑𝑦+∫^{𝑡⋅𝑣𝑓}_{𝑡⋅𝑣𝑓−𝑎}𝑘(𝑦,𝑡)𝑑𝑦;(b)for 𝑡𝑣_𝑓−𝑎<𝑥≤𝑡𝑣_𝑓∶𝐴(𝑥,𝑡)=∫^{𝑡⋅𝑣𝑓}_𝑥𝑘(𝑦,𝑡)𝑑𝑦 and 𝐵(𝑥,𝑡)=∫^{𝑡⋅𝑣𝑚}_{𝑡⋅𝑣𝑚−𝑎}𝑘(𝑦,𝑡)𝑑𝑦+∫^{𝑡⋅𝑣𝑓−𝑎𝑡⋅𝑣}_𝑚𝑘(𝑦,𝑡)𝑑𝑦+ ∫^{𝑥𝑡⋅𝑣}_𝑓−𝑎𝑘(𝑦,𝑡)𝑑𝑦;(c)for 𝑡𝑣_𝑚≤𝑥≤𝑡𝑣_𝑓−𝑎∶𝐴(𝑥,𝑡)=∫^{𝑡⋅𝑣𝑓𝑥−𝑎}𝑘(𝑦,𝑡)𝑑𝑦+∫^{𝑡⋅𝑣𝑓}_{𝑡⋅𝑣𝑓−𝑎}𝑘(𝑦,𝑡)𝑑𝑦 and 𝐵(𝑥,𝑡)=∫^{𝑡⋅𝑣𝑚}_{𝑡⋅𝑣𝑚−𝑎}𝑘(𝑦,𝑡)𝑑𝑦+ ∫^{𝑥𝑡⋅𝑣}_𝑚𝑘(𝑦,𝑡)𝑑𝑦;(d)for 𝑡𝑣_𝑚−𝑎≤𝑥<𝑡𝑣_𝑚∶𝐴(𝑥,𝑡)=∫^{𝑡⋅𝑣𝑓−𝑎𝑡⋅𝑣}_𝑚𝑘(𝑦,𝑡)𝑑𝑦+∫^{𝑡⋅𝑣𝑚}_𝑥𝑘(𝑦,𝑡)𝑑𝑦+∫^{𝑡⋅𝑣𝑓}_{𝑡⋅𝑣𝑓−𝑎}𝑘(𝑦,𝑡)𝑑𝑦 and 𝐵(𝑥,𝑡)=∫^{𝑥𝑡⋅𝑣}_𝑚−𝑎𝑘(𝑦,𝑡)𝑑𝑦;(e)for𝑥<𝑡𝑣_𝑚−𝑎∶𝐴(𝑥,𝑡)=∫^{𝑡⋅𝑣𝑚}_{𝑡⋅𝑣𝑚−𝑎}𝑘(𝑦,𝑡)𝑑𝑦+∫^{𝑡⋅𝑣𝑓−𝑎𝑡⋅𝑣}_𝑚𝑘(𝑦,𝑡)𝑑𝑦+∫^{𝑡⋅𝑣𝑓}_{𝑡⋅𝑣𝑓−𝑎}𝑘(𝑦,𝑡)𝑑𝑦 and 𝐵(𝑥,𝑡)=0.

The platoon dispersion model proposed in this paper is described in the previous section. If 𝑥 is set as the upstream and downstream signal location, then how dispersion characteristics of the queuing vehicles at the upstream intersection influence the downstream green phase start time setup can be quantitatively analyzed, as the platoon moves down from an upstream intersection at green phase end time to downstream intersection. The results can be used to calculate the traffic flow parameters used in signal coordination, such as delay stop and queue length.

3. The Front and Rear of a Platoon in the Dispersion Model

In general, only dispersion behavior at the front and rear of the platoon is important in traffic signal coordination. When adjacent intersections are not too far apart, fast cars at the rear of the platoon are unable to get to the front and the slower cars at the front do not have time to filter back to the rear. Hence, the front and rear of the platoons may be treated separately.

3.1. Front of the Platoon

A good design of coordinated lights aims at reducing the number of platoon leaders stopped at the second intersection before its light turns green. The rear does not significantly affect the front, which helps in the mathematical analysis of the behavior of the front of the platoon. Using Pacey’s assumptions, the initial density function 𝑘(𝑥,0) of the front of the platoon is defined by𝑘(𝑥,0)=𝑘0,𝑥>0,_𝑗,𝑥≤0.(3.1)

The density of the front of the platoon past 𝑥 at time 𝑡, as obtained from (2.4) and (2.5), is𝑘(𝑥,𝑡)=𝑐𝑘_𝑗^{(𝑡𝑣𝑓/𝜇−𝑡)/𝛼𝑡(𝑥/𝜇−𝑡)/𝛼𝑡}1√2𝜋𝑒^−0.5𝑦2=𝑐𝑘_𝑗𝑑𝑣2𝐹𝑧²=𝑡𝑣^𝑓/𝜇−𝑡√2𝛼𝑡−𝐹𝑧¹=𝑥/𝜇−𝑡=𝑐𝑘_𝑗√2𝛼𝑡2[𝐹(𝑧)]^𝑧2𝑧1.(3.2)

As mentioned previously, cars at the front travel at a range of speeds [𝜇,𝑣_𝑓], leading to the spread of cars along the section [𝑡𝜇,𝑡𝑣_𝑓]. Hence, the number of cars 𝐴(𝑥,𝑡) from the front of the platoon that have passed the downstream location 𝑥 at time 𝑡 can be calculated under the following three scenarios:(a)for 𝑥≤𝑡𝜇∶𝐴(𝑥,𝑡)=((𝑐𝑘_𝑗𝜇√2𝛼𝑡)/2)[𝑧𝐹((𝑡𝑣_𝑓/𝜇−𝑡)/√2𝛼𝑡)−𝐺(𝑧)]^{(𝑡𝑣𝑓√/𝜇−𝑡)/02𝛼𝑡)};(b)for 𝑡𝜇<𝑥≤𝑡𝑣_𝑓∶𝐴(𝑥,𝑡)=(𝑐𝑘_𝑗/2)𝐹((𝑡𝑣_𝑓/𝜇−𝑡)/√2𝛼𝑡)(𝑡𝑣_𝑓−𝑥)−((𝑐𝑘_𝑗𝜇√2𝛼𝑡)/2)[𝐺(𝑧)]^{(𝑡𝑣𝑓√/𝜇−𝑡)/√2𝛼𝑡)(𝑥/𝜇−𝑡)/}_2𝛼𝑡);(c)for 𝑥>𝑡𝑣_𝑓∶𝐴(𝑥,𝑡)=0.

3.2. Rear of the Platoon

Another goal of signal coordination is to reduce the number of stragglers at the rear who miss the green phase. Assuming the upstream signal green time ends at time 0, the initial density function 𝑘(𝑥,0) of the rear of the platoon, according to Pacey’s assumptions, is defined by𝑘(𝑥,0)=𝑘0,𝑥<0,₂,𝑥≥0,(3.3) where 𝑘₂≤𝑘_𝑗 is the density near the rear of the platoon.

Applying a similar limit process to (3.2) to calculate the proportion of the rear of platoon that has past 𝑥 at time 𝑡, we obtain𝑘(𝑥,𝑡)=𝑐𝑘₂^{(𝑥/𝜇−𝑡)/𝛼𝑡(𝑡𝑣}_{𝑚/𝜇−𝑡)/𝛼𝑡}1√2𝜋𝑒^−0.5𝑦2=𝑐𝑘₂𝑑𝑣2𝐹𝑧²=𝑥/𝜇−𝑡√2𝛼𝑡−𝐹𝑧¹=𝑡𝑣^𝑚/𝜇−𝑡√2𝛼𝑡=𝑐𝑘2²[𝐹(𝑧)]^𝑧2𝑧1.(3.4)

The previous calculations show that the speed of vehicles in the rear of the platoon is less than 𝜇, which means that these vehicles are spread out along the section [𝑡𝑣_𝑚,𝑡𝜇]. Hence, the number of cars 𝐵(𝑥,𝑡) from the rear that have not passed the downstream location 𝑥 at time 𝑡 can be calculated under the following three scenarios:(a)for 𝑥≤𝑡𝑣_𝑚∶𝐵(𝑥,𝑡)=0;(b)for 𝑡𝑣_𝑚<𝑥≤𝑡𝜇∶𝐵(𝑥,𝑡)=((𝑐𝑘₂𝜇√2𝛼𝑡)/2)[𝐺(𝑧)]^{√(𝑥/𝜇−𝑡)/2𝛼𝑡(𝑡𝑣}_{𝑚√/𝜇−𝑡)/2𝛼𝑡}−(𝑐𝑘₂/2)(𝑥−𝑡𝑣_𝑚)𝐹((𝑡𝑣_𝑚/𝜇−𝑡)/√2𝛼𝑡);(c)for 𝑥>𝑡𝜇∶𝐵(𝑥,𝑡)=((𝑐𝑘₂𝜇√2𝛼𝑡)/2)[−𝑧𝐹((𝑡𝑣_𝑚/𝜇−𝑡)/√2𝛼𝑡)+𝐺(𝑧)]^0(𝑡𝑣_{𝑚√/𝜇−𝑡)/2𝛼𝑡}.

4. Numerical Calculation

Form proposed model, 𝑘_𝑗 and 𝑘₂ are not related with diffusion of platoons, which arises only from the differences in speed between vehicles (𝑘_𝑗 and 𝑘₂ only decide how many cars are spreading along road). Wei et al.’s study shows that the initial flow is approximately a rectangular pulse with maximum flow 𝑄=𝑘_𝑗𝜇=𝑘₂𝜇 [17]. Hence, 𝑘(𝑥,𝑡), 𝐴(𝑥,𝑡), and 𝐵(𝑥,𝑡) could be replaced by 𝑘(𝑥,𝑡)/𝑄, 𝐴(𝑥,𝑡)/𝑄, and 𝐵(𝑥,𝑡)/𝑄 to calibrate the model. Using test data in Grace and Potts’s paper [5], upstream intersection 𝑥=0 and downstream intersection 𝑥=𝑥_𝑑 have the following parameters: 𝑣_𝑚=10.1m/s, 𝑣_𝑓=33.5m/s, 𝜇=13.4m/s, and 𝜎=2m/s. Generally, if the offset of the downstream intersection is set as 𝑡₀=𝑥_𝑑/𝜇, then the queuing vehicles at the upstream intersection, travelling at an average speed, can pass downstream intersection at the time.

To verify the validity of the proposed model, this paper compares the difference between the front and rear platoon dispersion characteristics in the proposed model and in Pacey’s model. Furthermore, the effect of changing parameter 𝛼 is examined hereinafter, to quantify how it affects the spreading of the platoon.

4.1. Platoon Density Distribution Function

The difference in the density distribution function between proposed model and Pacey’s model decides that our model is more realistic than Pacey’s model. In order to prove that, 𝑘(𝑥,𝑡)/𝑄, which denotes the ratio to the maximum initial flow of density of platoon past 𝑥 at time 𝑡, is calculated for both the proposed model and Pacey’s model at three time points 𝑡=𝑡_𝑜𝜇/𝑣_𝑓, 𝑡_𝑜, (𝑡_𝑜𝜇+𝑎)/𝑣_𝑚 under 𝑥_𝑑=45 μ, and the results are shown in Figure 2.

Figure 2 

Comparison of the proposed model’s and Pacey’s density distribution function 𝑘(𝑥,𝑡) under 𝑥𝑑=45 μ.

The following can be concluded based on Figure 2. (a)The speed density of both Pacey’s model and proposed model follows a normal distribution, which lead to a situation that there are more vehicles traveling around the mean speed, and fewer vehicles at higher or lower speeds. The speed distribution determines the platoon density distribution function. Therefore, the density in the middle of the platoon is higher than that in the front or rear of the platoon. As time passes, the platoon becomes more dispersed along the road, and the hump of the platoon density distribution function becomes less significant.(b)In the proposed model, the queuing vehicles traveling at different speed 𝑣 depart from their stop positions at time 0, and these cars are spreading along the section 𝑥∈[𝑡𝑣_𝑚−𝑎,𝑡𝑣_𝑓] at time 𝑡. There are the following three stages: if time is 𝑡∈[0,𝑡₀𝜇/𝑣_𝑓], the front of platoon has not arrived at the downstream intersection 𝑥=𝑥_𝑑, then 𝑡𝑣_𝑓<𝑥_𝑑, and 𝑘(𝑥_𝑑,𝑡)=0; if time is 𝑡∈[𝑡₀𝜇/𝑣_𝑓,(𝑡₀𝜇+𝑎)/𝑣_𝑚], some vehicles are starting to pass the downstream intersection 𝑥=𝑥_𝑑, and 𝑡𝑣_𝑚−𝑎≤𝑥_𝑑≤𝑡𝑣_𝑓 and 𝑘(𝑥_𝑑,𝑡)≠0; if time is 𝑡∈[(𝑡₀𝜇+𝑎)/𝑣_𝑚,+∞], the rear of the platoon has passed the downstream intersection location 𝑥=𝑥_𝑑, and 𝑡𝑣_𝑚−𝑎>𝑥_𝑑 and 𝑘(𝑥_𝑑,𝑡)=0.(c)In Pacey’s model, the spread of vehicles in the speed range [𝑣_𝑚,𝑣_𝑓] during time period 𝑡∈[𝑡₀𝜇/𝑣_𝑓,(𝑡₀𝜇+𝑎)/𝑣_𝑚] is same as proposed model. However, Pacey’s model assumes that speed is extending within the range [−∞,+∞]. It is impossible for a vehicle to have a positive infinity speed to travel to downstream infinity or a negative infinity speed to travel backwards to upstream infinity, which obviously does not match the field observations. Therefore, the application of Pacey’s model is limited.(d)The difference in the speed density between proposed model and Pacey’s model decides that there are also more cars in the middle of the platoon and fewer cars in the two tails in the former, compared to the latter.

4.2. Number of Cars at the Front That Have Passed the Downstream Intersection

If the green phase of the downstream intersection is started at 𝑡₀=𝑥_𝑑/𝜇, as cars in the front of the platoon travel at a speed greater than 𝜇, then the downstream signal needs to turn green 𝑡_ℎ in advance of 𝑡₀ to allow more vehicles to pass during the green phase. That is to say, the number of cars stopped at the front of platoon is 𝐴(𝑥_𝑑,𝑡_𝑜−𝑡_ℎ). For 𝑡₀=30,60,90,120 and 𝑡_ℎ=0,1,2,10, 𝐴(𝑥_𝑑,𝑡_𝑜−𝑡_ℎ)/𝑄, which denotes the ratio to the maximum initial flow of the average number of cars stopped at the front of the platoon, is calculated for both the proposed model and Pacey’s model, and the results are presented in Table 1.

Table 1 

The ratio to the maximum initial flow of the average number of cars having passed the downstream point at the front of platoon under 𝛼=0.15.

Table 1 shows that as the distance between the successive intersections increases, the speed range of the front of the platoon [𝜇+𝑎/𝑡₀,𝑣_𝑓] increases and 𝐴(𝑥_𝑑,𝑡_𝑜) also increases. Therefore, a higher preset 𝑡_ℎ is needed to allow more cars at the front of platoon to pass the downstream intersection. The difference in 𝐴(𝑥_𝑑,𝑡_𝑜−𝑡_ℎ) between the proposed model and Pacey’s model is 4.78%, that is, ((𝑐−1)/𝑐)100%. The difference is a result of the assumption in Pacey’s model that the speed spreads from negative infinity to positive infinity, which results in an accumulated probability in the area of [𝑣_𝑚,𝑣_𝑓] less than 1.

4.3. Number of Cars at the Rear That Have Not Passed the Downstream Intersection

It is assumed that the downstream signal green time ends at time 𝑡₀=(𝑥_𝑑+𝑎)/𝜇. According to the platoon dispersion model, the cars at the rear of the platoon are traveling at a speed lower than 𝜇. Therefore, the green phase needs to be postponed to time 𝑡_𝑡 to allow more vehicles at the rear of platoon to pass, which means that the number of vehicles not having passed the downstream signal location is 𝐵(𝑥_𝑑,𝑡_𝑡+𝑡₀). For 𝑡₀=30,60,90,120 and 𝑡_𝑡=0,1,2,10, 𝐵(𝑥_𝑑,𝑡_𝑡+𝑡₀)/𝑄, which denotes the ratio to the maximum initial flow of the average number of cars stopped at the rear of the platoon, is calculated for both the proposed model and Pacey’s model, and the results are presented in Table 2.

Table 2 

The ratio to the maximum initial flow of the average number of cars not having passed the downstream point at the rear of platoon under 𝛼=0.15.

The data in Table 2 show that as the distance between the successive intersections increases, the speed range of the rear of the platoon, [𝑣_𝑚,𝜇−𝑎/𝑡₀,], increases, and 𝐵(𝑥_𝑑,𝑡_𝑜) also increases. Therefore, a higher preset 𝑡_𝑡 is needed to allow more cars at the rear of platoon to pass the downstream intersection. As in the analysis of the front of the platoon, the difference in 𝐵(𝑥_𝑑,𝑡_𝑡+𝑡₀) between the proposed model and Pacey’s model is 4.78%, that is, ((𝑐−1)/𝑐)100%.

4.4. Impact Analysis for Variation Coefficient 𝛼

It can be concluded from the previous results that 𝑐 also determines the deviation of Pacey’s model from the real situation. 𝑓^′(𝑣) of 𝑣 is affected by 𝜎. As mentioned previously, 𝜎, relative to 𝑐, is affected by 𝛼. Hence, 𝛼 has some influence on the accumulated probability for speed range [𝑣_𝑚,𝑣_𝑓]. As 𝛼 increases, the speed range becomes smaller. This is why the deviation of Pacey’s model increases with larger values of 𝛼.

In addition, 𝛼 influences the platoon dispersion. A larger 𝛼 leads to a flatter shape, and a smaller probability around the average speed area; at the same time, the probability for both tails becomes larger. As shown in the derivation process of 𝑘(𝑥,𝑡), this is determined by the speed distribution. Thus, the same phenomenon can be seen in the platoon density distribution. To assess the impact of 𝛼 on 𝑘(𝑥,𝑡), 𝐴(𝑥,𝑡)/𝑄 of the front and 𝐵(𝑥,𝑡)/𝑄 of the rear are calculated separately for 𝛼=0.15 and 𝛼=0.20 under 𝑥_𝑑=30 μ and the results are shown in Figures 3 and 4. From these figures, we can conclude that as 𝛼 increases, longer preset and extension times are separately required to allow the cars at the front and the rear of the platoon to pass the downstream intersection. These results are consistent with visual analysis.

Figure 3 

Influence of 𝛼 on 𝐴(𝑥,𝑡) for the front of the platoon.

Figure 4 

Influence of 𝛼 on 𝐵(𝑥,𝑡) for the rear of the platoon.

5. Conclusion

Platoon dispersion is the foundation of coordinating traffic signal control in an urban traffic network. This paper proposes a new platoon dispersion model which assumes that speed density follows a truncated normal distribution. This addresses the main defect of Pacey’s model and matches the field situation. To calibrate proposed model, values of four parameters, namely, the average speed of vehicles, the standard deviation of speed, minimum speed, and maximum speed, are quantified. Using test data in Grace and Potts’s paper [5] in the numerical example, there are 4.78% fewer cars travelling in the front and the rear of the platoon between the proposed model and Pacey’s model, and we interpret the results for application of coordination of two traffic lights distance 𝑥_𝑑 apart to prove the validity of the proposed model. Future work needs to focus on proposed model with nonsynchronous start-up of all vehicles, validating the model using field data, and on simulation program development for the application of the proposed model in the timing of signal coordination.

Acknowledgments

This work was supported by the High-Technology Research and Development Program of China (863 program) under contract no. 2007AA11Z201 and the National Science Foundation of China under contract no. 61174188. This support is gratefully acknowledged. However, all facts, conclusions, and opinions expressed here are solely the responsibility of the authors. The authors thank the anonymous referee for her/his helpful comments.