Electrochemical Oxidation Using BDD Anodes Combined with Biological Aerated Filter for Biotreated Coking Wastewater Treatment

Wang, C. R.; Hou, Z. F.; Zhang, M. R.; Qi, J.; Wang, J.

doi:https://doi.org/10.1155/2015/201350

Journal of Chemistry

On this page

Abstract Introduction Materials and Methods Results and Discussion Conclusions Acknowledgments References Copyright Related Articles

Research Article | Open Access

Volume 2015 | Article ID 201350 | https://doi.org/10.1155/2015/201350

Electrochemical Oxidation Using BDD Anodes Combined with Biological Aerated Filter for Biotreated Coking Wastewater Treatment

C. R. Wang,¹Z. F. Hou,¹M. R. Zhang,¹J. Qi,¹and J. Wang¹

Academic Editor: Carlos A. Martínez-Huitle

Received26 Mar 2015

Revised01 Jun 2015

Accepted08 Jun 2015

Published29 Jun 2015

Abstract

Coking wastewater is characterized by poor biodegradability and high microorganism toxicity. Thus, it is difficult to meet Grade I of Integrated Wastewater Discharge Standard of China by biological treatment technology; specifically, COD cannot meet above standard due to containing refractory organics. A novel coupling reactor, electrochemical oxidation using BDD anodes and biological aerated filter (BAF), has been developed for carbon and nitrogen removal from biotreated coking wastewater, focusing on COD, BOD₅, -N, and -N removal on operation over 90 days with average effluent value of 91.3, 9.73, 0.62, and 13.34 mgL⁻¹, respectively. Average value of BOD₅/COD and BOD₅/-N was enhanced from 0.05 to 0.27 and from 0.45 to 1.21 by electrochemical oxidation, respectively, with average energy consumption of 67.9 kWh kg⁻¹ COD. In addition, the refractory organics also were evidently mineralized in the unit based on the data of the three-dimensional fluorescence spectra. Meanwhile, its effluent provided excellent substrate for biological denitrification in BAF. At hydraulic retention time (HRT) of 13.08 h, about 12 mgL⁻¹ -N was depleted through denitrification, and it mainly occurred at top of 0.25 m height of BAF. Therefore, it is feasible to apply the coupling reactor for biotreated coking wastewater treatment and achieve desirable effluent quality.

1. Introduction

The biologically treated coking wastewater usually cannot meet the stringent effluent standard in China, namely, Grade I of Integrated Wastewater Discharge Standard of China [1–6], especially, for COD less than 100 mg L⁻¹. And the effluent of biotreated coking wastewater showed the characteristics of poor biodegradability and lower carbon-nitrogen ratio. Therefore, upgrading of biotreated coking wastewater is first imperative.

At present, advanced oxidation processes (AOPs), such as ozone oxidation [7], wet air oxidation [8], Fenton oxidation [9], and electrochemical oxidation [4, 10, 11], are good alternative technologies for coking wastewater treatment, in which electrochemical oxidation technology using BDD anodes has been proposed due to its advantages regarding extremely wide potential window, very low background current, and robust oxidation capacity [12–15]. Zhu et al. [4] investigated the electrochemical oxidation using BDD anodes for advanced treatment of coking wastewater and under the condition of current density of 20–60 mA cm⁻², pH of 3–11, and temperature of 20–60°C, the complete mineralization of organic pollutants was almost achieved with energy consumption of 64 kWh kg⁻¹ COD. Haidar et al. [16] studied degradation of antibiotic sulfachloropyridazine using an electrochemical oxidation system with BDD anode, and the results showed that the system could efficiently remove the antibiotic from water and the higher mineralization rate can be obtained at increasing applied current. Urtiaga et al. [17] studied the remediation of wastewater containing tetrahydrofuran by electrochemical oxidation using BDD anodes, and the results showed that tetrahydrofuran can be totally mineralized by BDD anodes.

What is more, our group found that during the oxidation process for biotreated coking wastewater by BDD anodes in different electrolysis time [10] the ratio of BOD₅ to COD increased from an initial value of 0.05 to 0.65 at electrolysis time of 90 min and the BOD₅/-N ratio increased from an initial value of 0.48 to 1.25 at 45 min and then gradually dropped to 0.69 at 90 min. Moreover, the -N concentration in electrochemical oxidation effluent was evidently increased at electrolysis time of 90 min with energy consumption of 116.0 kWh kg⁻¹ COD. Therefore, based on the consideration of energy consumption and effluent characteristics in different electrolysis time, it is strongly suggested that electrochemical technology using BDD anodes should be combined with biological denitrification technology for the advanced treatment of biotreated coking wastewater to better remove organics and nitrogenous compounds.

Nowadays, tertiary biological technology for wastewater treatment and reclamation mainly was biological aerated filter (BAF). For examples, Chen et al. [18] adopted anaerobic/anoxic/aerobic and BAF system for wastewater treatment and mainly discussed the effects of COD/TN ratio and nitrate recycling ratio on nitrogen and phosphorus removal. Cui et al. [19] combined ozone oxidation and BAF processes for treatment of cyanide containing electroplating wastewater, and the results showed that BAF can tolerate higher cyanide toxicity than some other bioreactor and obtain high removal efficiency with low influent BOD₅/TN in BAF. Moreover, the cyanide compounds could be used as the nitrogen source for the microbes. In addition, regarding BAF’s features of simultaneously nitrification and denitrification, without settling tank and excellent effluent quality [20–22], it was selected as biological denitrification technology for advanced biotreated coking wastewater.

Accordingly, based on the effluent characteristics of electrochemical oxidation, combining the advantages of electrochemical oxidation using BDD anodes with BAF, the object of this study is to develop a novel coupling system for simultaneous removal of carbon and nitrogen from biotreated coking wastewater, and its performances for COD, BOD₅, -N, and -N removal in different periods were focused on. Meanwhile, improvement of biodegradability and carbon-nitrogen ratio, its energy consumption in EO unit, and removal characteristics of COD, -N, and -N as special distribution in BAF unit were also investigated.

2. Materials and Methods

2.1. Experimental Equipment

The experiment was carried out in a coupling reactor, consisting of electrochemical oxidation (EO) unit and BAF unit (in Figure 1), in which EO unit was made of Plexiglas with wok volume of 3 L. The electrodes constituted of 3 pieces of BDD anodes and 2 pieces of stainless steel cathodes at spacing of 1 cm. The anodes were purchased from CONDIAS GmbH (Germany) with size of 195 mm × 26 mm × 2 mm (length × width × thickness) [10]. The dimension of BAF was diameter of 10 cm, work height of 1.0 m, mainly packed with lava (diameter of 0.5 cm) as media.

2.2. Biotreated Coking Wastewater Quality and Effluent Standard

The biotreated coking wastewater in this paper was derived from a coking plant of the Capital Iron and Steel Group in Beijing, China; its main parameters of influent quality were shown in Table 1, with poor biodegradability (BOD₅/COD of 0.054–0.06) and low carbon-nitrogen ratio (BOD₅/-N of 0.48–0.52), while effluent quality was required to meet Grade I of Integrated Wastewater Discharge Standard of China (GB 8978-1996), in which several main parameters were listed in Table 1.

In addition, conductivity in biotreated coking wastewater was in range of 1850–1920 μS cm⁻¹.

2.3. Operating Conditions

Based on previous results from our group [10], conditions of EO were selected. It lasted for 90 days; three different long-term steady-state experimental runs () were carried out with HRT of 45 min and current density of 75 mA cm⁻² for EO unit. Meanwhile, HRT of BAF was kept at 13.08 h, 8.72 h, and 6.54 h with the same air/water ratio of 1 : 1 throughout the whole experimental period (see Table 2), in which, EO unit was intermittently operated and run 3.75 to 6.75 hours every day with treatment capacity of 4 L h⁻¹. BAF was continuously operated with treatment capacity of 14.4 L d⁻¹ to 28.8 L d⁻¹.

2.4. Analytical Instruments and Methods

COD, BOD₅, -N, and -N in influent and effluent of each reactor were analyzed daily, and COD was measured by a COD meter (ET99722, Hanna Corporation, Italy). BOD₅ was determined by dilution inoculation method. Ammonia (-N) concentration was obtained via Nessler’s reaction using UV2100 spectrophotometer (Shanghai Unico Instruments Co., Ltd., China). Nitrate (-N) concentration was detected by disulfonic acid phenol reaction using UV2100 spectrophotometer (Shanghai Unico Instruments Co., Ltd., China). Conductivity was tested by conductivity meter (CDC40103) (HACH, USA).

The fluorescence spectra were recorded using a spectrophotometer (F7000 fluorescence spectrophotometer, Hitachi, Japan) equipped with a 700-W xenon arc-lamp. Excitation scans were performed in the range 200–450 nm at fixed intervals of 10 nm, and the emission was recorded at wavelengths ranging from 260 to 550 nm in 10 nm steps with integration time of 0.1 s. The results file of each three-dimensional spectrum was saved in CSV format and then they were output by origin 8.0.

Energy consumption (EC) was calculated using the following equation [4, 23]: where EC is energy consumption (in kWh kgCOD⁻¹), is voltage (in V), is current (in A), is electrolysis time (in h), is initial COD concentration of influent (in mg L⁻¹), is COD concentration of effluent (in mg L⁻¹), and is volume of treated wastewater (in L).

3. Results and Discussion

3.1. Overall Performance of EO + BAF Coupling Reactor

Figures 2(a) and 2(b) show profiles of COD and BOD₅ concentration in influent and effluent of EO and BAF unit during experimental periods, respectively. As shown in Figures 2(a) and 2(b), COD and BOD₅ concentration in final effluent from the coupling system was maintained below 100 mg L⁻¹ and 20 mg L⁻¹ with the average value of 91.3 mg L⁻¹ and 9.73 mg L⁻¹, respectively, which met Grade I of Integrated Wastewater Discharge Standard of China (GB 8978-1996). And average value of BOD₅/COD ratio and BOD₅/-N ratio was enhanced by electrochemical oxidation from 0.05 to 0.27 and from 0.45 to 1.21, respectively, which was helpful for microorganism denitrification in BAF because of enough carbon resource, which also could be confirmed by data of nitrate removal (Figure 2(c)).

(a)

(b)

(c)

(d)

Figures 2(c) and 2(d) show profiles of -N and -N concentration in influent and effluent of EO and BAF unit during experimental periods, respectively. As shown in Figures 2(c) and 2(d), -N and -N concentration in final effluent from the coupling system was maintained below 15 mg L⁻¹ and 20 mg L⁻¹ with the average value of 0.62 mg L⁻¹ and 13.34 mg L⁻¹, respectively, which met Grade I of Integrated Wastewater Discharge Standard of China (GB 8978-1996) and -N concentration below 20 mg L⁻¹. It also can be found that nitrogen removal mainly occurred at BAF unit, and the impact of HRT of BAF on nitrate removal was much more evident than on ammonia and organics removal. Generally, nitrate removal efficiency increased with the increase of HRT. As influent ammonia concentration was lower, its variation tendency as HRT also was not obvious. In addition, due to the fact that BAF was run at air to water ratio of 1 : 1, the simultaneous nitrification and denitrification took place in BAF unit; thus organics may be partly removed by heterotrophic bacteria and partly removed by denitrifiers, which led to the fact that organics removal was not much more evident with the increase of HRT.

3.2. Pollutants Removal Efficiency and Energy Consumption in EO Unit

To clearly identify the performance in EO unit, COD, BOD₅, -N, and -N, removal efficiencies during different operating periods are presented in Figure 3. Average COD, BOD₅, -N, and -N removal efficiency by EO was 48.74%, −63.82%, 21.15%, and −2.57%, respectively.

Notably, the reason for BOD₅ concentration increase instead of decrease was that the biodegradability of biotreated coking wastewater was poor and the organics mainly were refractory organics, which can be confirmed from the three-dimensional fluorescence spectra (Figure 4(a)); there were two fluorescence peaks detected at and , respectively, from raw biotreated coking wastewater. The former peak was confirmed as aromatic-protein-like substance II and can be referred to as refractory biodegraded dissolved organic matter [24]. The latter peak represents humic acid-like substance. After the EO unit, the refractory organics were partly mineralized into CO₂ and H₂O and partly transferred into biodegradable organics, which can be found from the three-dimensional fluorescence spectra of effluent (Figure 4(b)). Compared with Figures 4(a) and 4(b), it can be found that the fluorescence intensity of aromatic-protein-like substance II has been greatly reduced from about 6100 to less than 150.

(a)

(b)

In addition, the increase of nitrate concentration after EO unit was mainly attributed to the nitrogen heterocyclic organic compounds and -N being oxidized by oxidant into -N [10], thus resulting in the increase in the -N concentration.

Based on (1), at the current density of 75 mA cm⁻² and HRT of 45 min, the mean voltage and current was 2.6 V and 15 A in EO unit, respectively, so when mean COD was removed from 221.2 mg L⁻¹ to 113.5 mg L⁻¹, the mean energy consumption was calculated as 67.9 kWh kg⁻¹ COD. Compared with the results from Zhu et al. [4], who studied advanced treatment of biologically pretreated coking wastewater by electrochemical oxidation using BDD electrodes with energy consumption of 64 kWh kg⁻¹ COD, Serikawa et al. [25] treated a wastewater with an initial COD concentration of 14000 mg L⁻¹ at a BDD pilot plant with energy consumption of 30 kWh kg⁻¹ COD and Anglada et al. [26] carried on a study on the electrochemical oxidation of landfill leachate by BDD anode with energy consumption of 53–94 kWh kg⁻¹ COD at different current density. The energy consumption of kg COD removal in this BDD anode was inexpensive.

3.3. Pollutants Removal Efficiency and Its Concentration Profile in BAF Unit

In BAF unit, COD, BOD₅, -N, and -N removal efficiencies during different operating periods also are presented in Figure 5. As HRT was decreased from 13.08 h to 8.72 h and 6.54 h, average COD removal efficiency by BAF was reduced from 24.45% to 18.40% and 14.55%, BOD₅ removal efficiency was reduced from 70.50% to 66.71% and 66.79%, and -N and -N removal efficiency was reduced from 87.69% to 86.88% and 85.55% and from 61.80% to 46.29% and 32.13%, respectively. It can be found that as HRT decreased, above pollutants removal efficiencies all were decreased in BAF unit, but all pollutants’ removal by BAF during different operating period was relatively stable.

Figure 6 shows profiles of COD, -N, and -N along the height of BAF at HRT of 13.08 h. It is evident that sudden drops in both COD and -N concentration occurred at top 0.25 m height of BAF due to denitrification quickly performed at the top of the BAF in the presence of abundant -N and biodegradable organics, while their concentrations were slowly varied at height of 0.5 m, 0.75 m, and 1.0 m. About 12 mg L⁻¹ -N was depleted through denitrification. Comparatively, -N concentration was slowly changed at different height of BAF with total 4.1 mg L⁻¹ ammonia removed.

4. Conclusions

A coupling system, electrochemical oxidation using BDD anodes and BAF, for biotreated coking wastewater treatment was investigated to study feasibility of simultaneous removal of carbon and nitrogen. Long-term operating results over 90 days showed desirable effluent quality and steady process performance with the average effluent concentration of COD, BOD₅, -N, and -N of 91.3, 9.73, 0.62, and 13.34 mg L⁻¹, respectively, reaching the Grade I of Integrated Wastewater Discharge Standard of China. Average value of BOD₅/COD and BOD₅/-N was improved from 0.05 to 0.27 and from 0.45 to 1.21, respectively, in electrochemical oxidation unit. Meanwhile, the data of three-dimensional fluorescence spectra in the unit confirmed that the refractory organics were evidently mineralized. At current density of 75 mA cm⁻² and HRT of 45 min, the mean energy consumption of EO unit was calculated as 67.9 kWh kg⁻¹COD and the corresponding COD, BOD₅, -N, and -N removal efficiency was 48.74%, −63.82%, 21.15%, and −2.57%, respectively. In addition, its effluent provided excellent substrate for biological denitrification in BAF. As its HRT was decreased from 13.08 h to 8.72 h and 6.54 h, all pollutants removal efficiencies were decreased. Based on the data at HRT of 13.08 h, the biological denitrification mainly occurred at top 0.25 m height of BAF, and about 12 mg L⁻¹ -N was depleted through denitrification in BAF unit. Therefore, it is feasible to apply the coupling system for biotreated coking wastewater treatment.

Conflict of Interests

The authors declare that there is no conflict of interests regarding the publication of this paper.

Acknowledgments

This research was funded by the Fundamental Research Funds for the Central Universities (no. 2009QH01) and the National High Technology Research and Development Program of China (863 Program) (no. 2015AA050501). The anonymous reviewers are also gratefully acknowledged for their very helpful comments and suggestions.

References

X. W. He, Z. Chai, F. P. Li et al., “Advanced treatment of biologically pretreated coking wastewater by electrochemical oxidation using Ti/RuO₂-IrO₂ electrodes,” Journal of Chemical Technology and Biotechnology, vol. 88, no. 8, pp. 1568–1575, 2013.
View at: Publisher Site | Google Scholar
X. Zhou, Y. X. Li, Y. Zhao, and X. P. Yue, “Pilot-scale anaerobic/anoxic/oxic/oxic biofilm process treating coking wastewater,” Journal of Chemical Technology and Biotechnology, vol. 88, no. 2, pp. 305–310, 2013.
View at: Publisher Site | Google Scholar
M. H. Zhang, Q. L. Zhao, X. Bai, and Z. F. Ye, “Adsorption of organic pollutants from coking wastewater by activated coke,” Colloids and Surfaces A: Physicochemical and Engineering Aspects, vol. 362, no. 1–3, pp. 140–146, 2010.
View at: Publisher Site | Google Scholar
X. Zhu, J. Ni, and P. Lai, “Advanced treatment of biologically pretreated coking wastewater by electrochemical oxidation using boron-doped diamond electrodes,” Water Research, vol. 43, no. 17, pp. 4347–4355, 2009.
View at: Publisher Site | Google Scholar
P. Lai, H.-Z. Zhao, M. Zeng, and J.-R. Ni, “Study on treatment of coking wastewater by biofilm reactors combined with zero-valent iron process,” Journal of Hazardous Materials, vol. 162, no. 2-3, pp. 1423–1429, 2009.
View at: Publisher Site | Google Scholar
P. Lai, H.-Z. Zhao, C. Wang, and J.-R. Ni, “Advanced treatment of coking wastewater by coagulation and zero-valent iron processes,” Journal of Hazardous Materials, vol. 147, no. 1-2, pp. 232–239, 2007.
View at: Publisher Site | Google Scholar
S. H. Zhang, J. Zheng, and Z. Q. Chen, “Combination of ozonation and biological aerated filter (BAF) for bio-treated coking wastewater,” Separation and Purification Technology, vol. 132, pp. 610–615, 2014.
View at: Publisher Site | Google Scholar
H. L. Chen, G. Yang, Y. J. Feng et al., “Biodegradability enhancement of coking wastewater by catalytic wet air oxidation using aminated activated carbon as catalyst,” Chemical Engineering Journal, vol. 198-199, pp. 45–51, 2012.
View at: Publisher Site | Google Scholar
L. B. Chu, J. L. Wang, J. Dong, H. Y. Liu, and X. L. Sun, “Treatment of coking wastewater by an advanced Fenton oxidation process using iron powder and hydrogen peroxide,” Chemosphere, vol. 86, no. 4, pp. 409–414, 2012.
View at: Publisher Site | Google Scholar
C. R. Wang, M. R. Zhang, W. Liu, M. Ye, and F. J. Su, “Effluent characteristics of advanced treatment for biotreated coking wastewater by electrochemical technology using BDD anodes,” Environmental Science and Pollution Research, vol. 22, no. 9, pp. 6827–6834, 2015.
View at: Publisher Site | Google Scholar
C. H. Zhang, H. Lin, J. Chen, and W. W. Zhang, “Advanced treatment of biologically pretreated coking wastewater by a bipolar three-dimensional electrode reactor,” Environmental Pollution, vol. 34, p. 2371, 2013.
View at: Google Scholar
M. Panizza and G. Cerisola, “Electro-fenton degradation of synthetic dyes,” Water Research, vol. 43, no. 2, pp. 339–344, 2009.
View at: Publisher Site | Google Scholar
J. Jeong, C. Kim, and J. Yoon, “The effect of electrode material on the generation of oxidants and microbial inactivation in the electrochemical disinfection processes,” Water Research, vol. 43, no. 4, pp. 895–901, 2009.
View at: Publisher Site | Google Scholar
C. A. Martínez-Huitle and E. Brillas, “Electrochemical alternatives for drinking water disinfection,” Angewandte Chemie—International Edition, vol. 47, no. 11, pp. 1998–2005, 2008.
View at: Publisher Site | Google Scholar
M. Panizza and G. Cerisola, “Application of diamond electrodes to electrochemical processes,” Electrochimica Acta, vol. 51, no. 2, pp. 191–199, 2005.
View at: Publisher Site | Google Scholar
M. Haidar, A. Dirany, I. Sirés, N. Oturan, and M. A. Oturan, “Electrochemical degradation of the antibiotic sulfachloropyridazine by hydroxyl radicals generated at a BDD anode,” Chemosphere, vol. 91, no. 9, pp. 1304–1309, 2013.
View at: Publisher Site | Google Scholar
A. Urtiaga, P. Fernandez-Castro, P. Gómez, and I. Ortiz, “Remediation of wastewaters containing tetrahydrofuran. Study of the electrochemical mineralization on BDD electrodes,” Chemical Engineering Journal, vol. 239, pp. 341–350, 2014.
View at: Publisher Site | Google Scholar
Y. Z. Chen, B. K. Li, L. Ye, and Y. Z. Peng, “The combined effects of COD/N ratio and nitrate recycling ratio on nitrogen and phosphorus removal in anaerobic/anoxic/aerobic (A²/O)-biological aerated filter (BAF) systems,” Biochemical Engineering Journal, vol. 93, pp. 235–242, 2015.
View at: Publisher Site | Google Scholar
J. Q. Cui, X. J. Wang, Y. L. Yuan, X. W. Guo, X. Y. Gu, and L. Jian, “Combined ozone oxidation and biological aerated filter processes for treatment of cyanide containing electroplating wastewater,” Chemical Engineering Journal, vol. 241, pp. 184–189, 2014.
View at: Publisher Site | Google Scholar
Q. Li, S. F. Sun, T. F. Guo et al., “Short-cut nitrification in biological aerated filters with modified zeolite and nitrifying sludge,” Bioresource Technology, vol. 136, pp. 148–154, 2013.
View at: Publisher Site | Google Scholar
G. Ji, J. Tong, and Y. Tan, “Wastewater treatment efficiency of a multi-media biological aerated filter (MBAF) containing clinoptilolite and bioceramsite in a brick-wall embedded design,” Bioresource Technology, vol. 102, no. 2, pp. 550–557, 2011.
View at: Publisher Site | Google Scholar
S.-H. Joo, D.-J. Kim, I.-K. Yoo, K. Park, and G.-C. Cha, “Partial nitrification in an upflow biological aerated filter by O2 limitation,” Biotechnology Letters, vol. 22, no. 11, pp. 937–940, 2000.
View at: Publisher Site | Google Scholar
C. R. Wang, M. R. Zhang, M. Ye, J. Wang, and G. W. Li, “Pilot-scale electrochemical oxidation combined with constructed wetland system for unconventional surface water treatment,” Journal of Chemical Technology and Biotechnology, vol. 89, no. 10, pp. 1599–1606, 2014.
View at: Publisher Site | Google Scholar
T. Liu, Z. L. Chen, W. Z. Yu, and S. J. You, “Characterization of organic membrane foulants in a submerged membrane bioreactor with pre-ozonation using three-dimensional excitation—emission matrix fluorescence spectroscopy,” Water Research, vol. 45, no. 5, pp. 2111–2121, 2011.
View at: Google Scholar
R. M. Serikawa, Y. Senda, and K. Sasaki, “Industrial E-AOP application using boron doped diamond electrodes,” in Proceedings of the 5th IWA Specialist Conference, Berlin, Germany, March 2009.
View at: Google Scholar
Á. Anglada, A. M. Urtiaga, and I. Ortiz, “Laboratory and pilot plant scale study on the electrochemical oxidation of landfill leachate,” Journal of Hazardous Materials, vol. 181, no. 1–3, pp. 729–735, 2010.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2015 C. R. Wang et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

2213

Downloads

1252

Citations