Photocatalytic Efficiency of TiO<sub>2</sub>-Biomass Loaded Mixture for Wastewater Treatment

Kanakaraju, Devagi; Wong, Soon Pang

doi:https://doi.org/10.1155/2018/4314969

Journal of Chemistry

On this page

Abstract Introduction Materials and Methods Results and Discussion Conclusion Conflicts of Interest Acknowledgments References Copyright Related Articles

Research Article | Open Access

Volume 2018 | Article ID 4314969 | https://doi.org/10.1155/2018/4314969

Photocatalytic Efficiency of TiO₂-Biomass Loaded Mixture for Wastewater Treatment

Devagi Kanakaraju¹and Soon Pang Wong¹

Academic Editor: Davide Vione

Received15 Sept 2017

Revised15 Dec 2017

Accepted21 Jan 2018

Published20 Mar 2018

Abstract

The objective of this study was to assess the efficiency of a novel TiO₂/modified sago bark (TiO₂/MSB) mixture for the degradation of sago wastewater effluent by employing response surface methodology (RSM) using chemical oxygen demand (COD) removal as the target parameter. The highest COD removal of 64.92% was obtained using TiO₂/MSB mixture sample prepared by combining 0.2 g/L TiO₂ and 1 w/w% MSB. Given that the highest removal was produced using this mixture sample, further optimisation of sago wastewater treatment was conducted by varying the independent variables, namely, dosage and contact time. Under this optimum condition, 0.10 g of 0.2 g/L TiO₂/1% MSB had successfully reduced 52.83% COD in 120 min. Surface morphology, functional groups, and elemental analysis supported observations of the ability of TiO₂/MSB mixture to remove COD. Additionally, aeration had further improved COD removal by 11%. The regression value () of the model indicated a high degree of correlation between the evaluated parameters. These results proved the feasibility of TiO₂ photocatalysis as an appealing alternative protocol for sago wastewater treatment and solid waste from the industry can be utilised for wastewater degradation.

1. Introduction

Solid or liquid wastes derived from a series of postprocessing steps in the agricultural industry could impose significant environmental impacts if not properly treated or managed. Agro-based industries contribute significantly to the economic growth and development of countries around the globe. Nevertheless, from the environmental point of view, this industry also inevitably tends to increase the accumulation of wastes, which demand considerable attention. The Advanced Oxidation Processes (AOPs) are nonbiological methods that could become the most suitable alternative to degrade organic compounds present in agricultural effluents.

AOPs, which are chemical oxidation processes, have been highly effective in the oxidation of wastewater containing toxic and organic materials [1]. AOPs involve in situ generation of reactive oxygen species (ROS), such as hydroxyl radicals (HO•), O₃, H₂O₂, and superoxide anion radical (). These ROS act as strong oxidants to oxidise organic compounds into biodegradable forms and simpler end-products, such as CO₂ and H₂O [2, 3]. Among the various AOPs, titanium dioxide (TiO₂) photocatalysis has been known for its potential to effectively treat wastewater. TiO₂ appears to be one of the most widely used photocatalysts because it is biologically and chemically inert, cheap, photostable, and noncorrosive [4]. Nonetheless, the application of TiO₂ in large-scale wastewater treatments is restricted by its limitations. TiO₂ has two major constraints that limit its photocatalytic activity: (i) the large bandgap (3.2 eV for anatase phase) limits its absorption to the UV region, in which only 3 to 5% of the solar spectrum can be utilised for its activation, and (ii) the fast recombination of photogenerated electron-hole pairs occurs during TiO₂ photocatalysis [5]. In addition, nanosized TiO₂ is in the form of slurry (suspension) during treatment, which makes recovery and recycling particularly difficult. Hence, to increase the photocatalytic activity of TiO₂, several methods have been proposed, such as doping with nonmetals and transition metals [6, 7], noble metal or metal ion incorporation [5, 8], fabrication of TiO₂ mixture with other materials [9], surface sensitisation [10], and the inclusion of inert support [11].

TiO₂ was combined with modified sago bark (MSB) to prepare a novel mixture material (TiO₂/MSB), which was then further assessed for the degradation of sago effluent which is known to be acidic in nature and typically characterised by high COD, biochemical oxygen demand (BOD), and total suspended solids (TSS). The sago residues from sago starch processing mills are abundant and readily available [12]. Sago bark (SB) is a type of solid waste generated during the debarking step of starch extraction process. Deposition or dumping of SB on land is the most common practice among most mill operators to address the disposal problem of this solid waste. Although such practice provides a short-term solution, potential environmental problems could, however, emerge in the long term. To the best of our knowledge, no studies have been performed on sago effluent by means of TiO₂ photocatalysis. SB, the solid waste, was also assessed as a potential support or adsorbent for the preparation of TiO₂-based mixtures. As RSM is known for its superiority in optimising chemical reactions [13], this study applied this statistical tool to determine the optimal conditions for the degradation of sago wastewater effluent, primarily focusing on COD as the target parameter.

Thus, the overall aim of this work was to investigate the effectiveness of the novel material TiO₂/MSB mixture on the degradation of sago wastewater effluent by optimising the process variables, namely, the dosage of TiO₂/MSB mixtures and contact time via RSM.

2. Materials and Methods

2.1. Materials

Ammonium iron(II) sulfate (Fe(NH₂)₂(SO₄)·6H₂O) and potassium dichromate (K₂Cr₂O₇) were purchased from R&M Chemical. Silver sulfate (Ag₂SO₄) and mercury(II) sulfate (HgSO₄) were obtained from Bendosen. Sulfuric acid (H₂SO₄, 95–97%) and titanium dioxide (TiO₂) (Degussa P25) with a particle size of 20–30 nm were supplied by Merck (Germany). Hydrochloric acid (HCl) and ferroin indicator solution were purchased from J. T. Baker and Sigma-Aldrich, respectively.

2.2. Sago Wastewater

Sago wastewater was collected from Herdsen Sago Industries in Pusa, Sarawak. Sampling was carried out twice. The effluent samples were filled into polyethylene bottles. The bottles were transported to the laboratory and kept refrigerated at 4°C until further analysis. Meanwhile, SB samples were randomly collected from piles of SB, which were produced by the debarking process, and stored in sack bags. The sack bags were also transported to the laboratory for further use. The raw wastewater samples were characterised for water quality parameters, namely, pH, BOD, COD, and TSS. Characteristics of sago wastewater were analysed based on the Standard Methods for Water and Wastewater Examination [14].

2.3. Analytical Determinations

COD, BOD, TSS, and total organic carbon (TOC) analyses were performed based on the Standard Methods for Water and Wastewater Examination [14]. TOC was measured using the OI Analytical (model Aurora 1030) TOC analyser.

2.4. Synthesis of TiO₂ Mixtures (TiO₂/MSB)

The sampled SB was washed using distilled water to remove dirt and unwanted materials. The washed SB was dried under sunlight before being cut and ground into a powdered form. The powdered form of SB was sieved to remove unwanted fibre and to obtain particles with similar sizes (500 μm). Subsequently, the powdered form of SB was soaked in 1 M HCl for 1 day. The SB was mainly comprised of cellulose, hemicelluloses, and lignin components [15], which can be dissolved or broken down during a pretreatment process [16]. Mosier et al. [17] and Zheng et al. [18] stated that diluted acid pretreatment process could dissolve almost all hemicelluloses and break down the bonds of cellulose and lignin. Due to the release of soluble organic compounds contained in the plant wastes, the application of untreated plant wastes as adsorbents could lead to several problems, such as low adsorption capacity, and high BOD, COD, and TOC values [19]. The acid-modified SB (MSB) was repeatedly washed using distilled water until the pH became neutral. Then, the neutralised MSB was dried in an oven at 100°C for 2 h. The dried MSB was then mixed with various concentrations of TiO₂ to prepare the TiO₂/MSB mixtures under mechanical stirring.

TiO₂ concentration was varied from 0.2 to 0.8 g/L, while the weight percentage of MSB was fixed as either 1 w/w% or 3 w/w%. A total of six TiO₂/MSB mixtures were prepared: (i) 0.2 g/L TiO₂/1% MSB, (ii) 0.2 g/L TiO₂/3% MSB, (iii) 0.4 g/L TiO₂/1% MSB, (iv) 0.4 g/L TiO₂/3% MSB, (v) 0.8 g/L TiO₂/1% MSB, and (vi) 0.8 g/L TiO₂/3% MSB. In this study, a fixed concentration of TiO₂ was added to a fixed weight percentage of MSB in a beaker, followed by 100 mL of ultrapure water. The mixture was then stirred at 750 rpm for 1 to 2 h to attain a homogeneous suspension. Next, the suspension was filtered and dried in an oven at 100°C for 2 h. The dried TiO₂/MSB mixture was pounded into a powdered form for further analysis. Figure 1 shows the prepared TiO₂/MSB mixture.

2.5. Material Characterisations

The raw SB, MSB, and TiO₂ mixtures were characterised for their surface morphology using a scanning electron microscope (SEM) (model: JOEL JSM-6390LA). The functional groups of TiO₂, MSB, and TiO₂/MSB were identified using Fourier transform infrared spectroscopy (model: Thermo Nicolet iS10). Elemental analysis of TiO₂/MSB was conducted using energy-dispersive X-ray spectroscopy (EDX) (model: JOEL JSM-6390LA). The crystalline structures of the mixture were observed using X-ray diffraction (XRD, PANalytical X’pert Pro) method with Cu Kα radiation (λ = 0.154 nm) in the scanning range of between 10° and 80°, at a rate of 0.04° per second. For phase identification, an automatic JCPDS library search and match was used.

2.6. Photocatalytic Experiment

For the photocatalytic experiment, the dosage of TiO₂/MSB mixture and contact time were optimised by employing the RSM. Different dosages of TiO₂/MSB mixture were added to a beaker containing 200 mL of filtered sago wastewater sample. Sago wastewater sample was filtered prior to treatment to ensure that the roughage, being the major portion of the wastewater, does not interfere with the final COD reading and block the penetration of UV light during the photocatalytic experiment. The solution mixture was subsequently stirred at 750 rpm in the dark for 30 min to establish absorption and equilibrium by the TiO₂/MSB mixture. The mixture was then irradiated using a UVC lamp (λ = 254 nm, Phillips TUV 8 W) for 2 h under continuous stirring (Figure 2). The distance of the vertically placed UV lamp from the solution beaker was fixed at 9 cm. Temperature and light intensity were measured during all photocatalytic experiments. A light meter (Sunche, HS1010) was used to measure the amount of light emitted by the UV lamp. Temperature of the solution mixture in the beaker ranged from 32°C to 34°C while the light intensity varied between 128 and 135 lux. Samples were withdrawn using a syringe prior to irradiation (after 30 min equilibrium) and at fixed time intervals throughout the 2 h irradiation period. The collected samples were centrifuged and the supernatant was subjected to COD analysis.

2.7. Experimental Design

The present study also used the central composite design (CCD). CCD consists of 2^k factorial points, augmented with axial points and a centre point, where represents the number of variables involved [2]. In the present work, the independent variables were TiO₂/MSB mixture dosage and contact time, while COD removal was the dependent variable (response). A total of 13 experiments were conducted with 4 factorial points, 4 axial points, and 1 centre point. The centre point was repeated five times to obtain an accurate result. Table 1 shows the ranges and levels of the independent variables in coded units.

The initial design included 13 tests, based on a CCD, as shown in [20]where represents the percentage of COD removal, while COD₀ and COD_f represent the measured COD values, before and after the TiO₂ photocatalytic experiment, respectively. Table 2 lists the 13 experiments conducted in this study, with the ranges and levels in coded units.

The Design-Expert 7.1.6 software was used to analyse the experimental data that were fitted to a second-order polynomial equation. The interaction between the dependent and independent variables was attained through the following equation [21]:where represents the predicted response (dependent variable); is the number of patterns; and are the index numbers for the patterns; is the offset or free term, known as the intercept term; are the coded independent variables; is the first-order (linear) main effect; is the quadratic (square) effect; is the interaction effect; and is the random error between the experimental and predicted values.

By representing (2) with two independent variables, it could be simplified as shown in Due to the regression and mean square residual error, analysis of variance (ANOVA) was used to test the statistical significance of the ratio of mean square variation [22]. The coefficient of determination () was used to express the quality of the fit of the polynomial model. Meanwhile, the probability values ( values) with 95% confidence level can act as a tool to evaluate the significance of the model terms [23]. Generally, if the significant probability value () is small (<0.05) and the value is less than 0.01, the model is considered to be statistically significant and acceptable [24]. The main indicators, which included the probability value (Prob. > ), model -value (Fisher’s variation ratio), and adequate precision, showed the adequacy and significance of the employed model. To find an optimum condition, response plots, namely, contour and 3D plots, were used. Fischer’s -test was utilised to determine the statistical significance and to optimise the desired target fixed for maximum removal of COD. For process optimisation, the desired target for the response (COD removal) was selected as “target,” while the independent variables (dosage and contact time) were chosen to be “within the range.” To determine the best and optimised local maximum, these individual targets were combined into an overall desirability function by the software [25].

3. Results and Discussion

3.1. Characterisation of TiO₂/MSB Mixture

Surface morphologies of raw SB and MSB acquired by SEM are shown in Figures 3(a) and 3(b), respectively. SEM micrographs revealed that the chemical modification by HCl has afforded a rougher surface morphology for the MSB (Figure 3(b)) compared to the unmodified SB (Figure 3(a)). Figure 3(a) shows the presence of fibre or starch granules (white arrow) on the surface of SB, which appeared to decrease or almost disappeared in the SEM micrograph of MSB (Figure 3(b)). The average pore sizes of raw SB and MSB were 0.08 μm and 0.10 μm, respectively. As the pore size difference between the raw SB and MSB was marginal, this could imply that the HCl treatment did not alter the pore size of SB.

(a)

(b)

SEM images of 0.2 g/L TiO₂/1% MSB mixture, before and after photocatalytic treatments, are shown in Figures 4(a) and 4(b), respectively. Figure 4(a) clearly shows that TiO₂ particles (white circle) have been successfully attached on the surface of the MSB (white arrow). The average pore size of TiO₂/MSB was recorded as 0.16 μm. However, in Figure 4(b), the amount of TiO₂ particles attached on the MSB surface was observed to be reduced after undergoing photocatalytic treatment. This could be due to the fall of TiO₂ from the MSB during the photoinduced degradation of organic pollutants present in sago effluent, as TiO₂/MSB mixture was synthesised via mechanical stirring [26]. As such, TiO₂/MSB could not potentially be recycled. Furthermore, no pores were detected after the treatment (Figure 4(b)). A possible explanation is that this might be due to the adsorption of organic pollutants on the adsorbent’s pores.

(a)

(b)

The EDX spectrum of the optimum TiO₂/MSB mixture that consisted of 0.2 g/L TiO₂/1% MSB is shown in Figure 5. The presence of three main elements, namely, C, Ti, and O, in the mixture was detected and their mass percentages are summarised in Table 3. As shown in the table, the mass percentages of C, Ti, and O were found to be 14.59%, 26.53%, and 58.88%, respectively. The presence of Ti and O indicated that the TiO₂/MSB mixture has been successfully prepared in this study.

The FTIR spectra of commercial TiO₂, MSB, and 0.2 g/L TiO₂/1% MSB mixture in the range of 4000 to 400 cm⁻¹ wavenumber are shown in Figure 6. The region between 400 and 700 cm⁻¹ in Figure 6(a) was assigned to Ti-O stretching and Ti-O-Ti bridging stretching modes [27]. The presence of TiO₂ was confirmed by the peaks at 526.97 cm⁻¹ and 666.97 cm⁻¹ (Figure 6(a)). The peaks located at 3352.77 cm⁻¹ and 3326.24 cm⁻¹ in Figures 6(b) and 6(c), respectively, corresponded to the stretching vibrations of hydroxyl groups (OH) present in the cellulose, hemicelluloses, and lignin of SB [28]. The peak around 2928 cm⁻¹ in both Figures 6(b) and 6(c) corresponded to the C−H stretching vibrations in the methyl, methoxyl, and methylene groups, which were present in the saccharide and aromatic structures of the hydrolysed products [29]. The strong stretching vibration peak observed around 1643 cm⁻¹ (Figures 6(b) and 6(c)) can be attributed to a carbonyl group (C=O), which provides evidence of the high carbon content in SB [30]. As shown in Figure 6(c), the peaks at 1425.97 cm⁻¹ and 1368.15 cm⁻¹ represent the CH₂ and OH bending, respectively [28]. The peaks around 1155 cm⁻¹ and 1020 cm⁻¹ confirmed the presence of arabinosyl residues and -glucan of hemicellulose, respectively [30]. The peak at 672.29 cm⁻¹ indicated the presence of TiO₂ in the TiO₂/MSB mixture (Figure 6(c)), which was found to be absent in the MSB spectrum (Figure 6(b)). Furthermore, the appearance of absorption peaks around 575 cm⁻¹ in both Figures 6(b) and 6(c) can be associated with the accumulation of oxide particles in SB [30].

(a)

(b)

(c)

Figure 7 shows the XRD pattern of 0.2 g/L TiO₂/1% MSB mixture. Five of the diffraction peaks centered at 2θ = 15.03° (101), 17.01° (101), 22.82° (002), 25.33° (101), and 47.92° (200) corresponded to 0.2 g/L TiO₂/1% MSB mixture. As shown in Figure 7, the diffraction peaks located at 2θ values of 25.33° and 47.92° corresponded to the (101) and (200) anatase TiO₂ crystal planes, respectively [31]. The peaks at 15.03° (101), 17.01° (101), and 22.82° (002) in Figure 7 corresponded to cellulose. Abou-Sekkina et al. [32] reported the XRD pattern of cellulose for an untreated fibre with the crystalline peaks at values of 15.0° (101), 16.5° (101), and 22.8° (002), respectively. The obtained XRD pattern indicated that HCl pretreatment did not completely remove the cellulose or hemicelluloses in MSB.

3.2. Photodegradation of Wastewater

The supernatant of sago effluent appeared as pale brownish in colour, with a pungent smell. The sago wastewater had also demonstrated an acidic value ranging from 5.12 to 6.06. The TSS, BOD, and COD of the wastewater ranged from 4,000 to 8,200 mg/L, 800 to 3,300 mg/L, and 6,192 to 34,048 mg/L, respectively. Several preliminary experiments were conducted in the presence of UV irradiation using (i) sago wastewater only, (ii) a mixture of SB and sago wastewater, (iii) a mixture of MSB and sago wastewater, and (iii) a mixture of sago wastewater and TiO₂. Sago wastewater was treated under UV irradiation to investigate the effect of photolysis, while the degradation of sago wastewater in the presence of commercial TiO₂, SB, and MSB was performed to assess their individual effects on the degradation of organic pollutants. The photolysis of sago wastewater under UV irradiation exhibited poor COD removal of less than 10% after 120 min of treatment (Figure 8). This thus confirmed the poor photolysis effect on the degradation of sago wastewater. On the other hand, the photocatalytic treatment of sago wastewater in the presence of 0.50 g/L TiO₂ yielded much better COD removal. The highest COD removal of 45.00% was attained after 90 min of UV irradiation using 0.50 g/L TiO₂. This value was slightly higher compared to the value obtained in the presence of SB and MSB, with 24.24% and 37.90%, respectively, after 120 min of treatment. The higher removal percentage of COD by the MSB could be due to the adsorption effect demonstrated by the modified material. TiO₂ photocatalysis has thus ascertained its contribution in removing organic pollutants from sago wastewater, despite the slight fluctuation observed during treatment (Figure 7). This could be due to the solution’s opacity, which could have increased the light scattering effect of the TiO₂ nanoparticles used in the treatment [33]. The solution’s opacity, caused in part by TiO₂ nanoparticles [34], would lead to a reduction of light penetration in the wastewater solution [35]. Moreover, interactions between the pollutants and the intermediates or degradants formed during the course of treatment could have plausibly caused the TiO₂ particles to coagulate, leading to a reduction of TiO₂ surface area and consequently its photocatalytic efficiency [36].

Six different TiO₂/MSB mixtures, which were prepared under different conditions, were applied in the sago wastewater degradation (Figure 9). The concentration of TiO₂ was varied from 0.20 g/L to 0.80 g/L, while the amount of MSB was fixed as either 1 w/w% or 3 w/w%. Among these samples, both 1 w/w% and 3 w/w% of MSB, when combined with 0.2 g/L TiO₂, had yielded relatively high COD removal of 64.29% and 61.54%, respectively, after 120 min of treatment. The obtained percentages of COD removal by the four other mixtures under similar treatment time had varied from 7.69% to 56.52%. The higher COD lowering capacity exhibited by TiO₂/MSB mixtures compared to the results obtained using only the commercial TiO₂ and MSB (Figure 9) could be attributed to the synergistic effect between TiO₂ and MSB. The presence of the synergistic effect in the TiO₂/MSB mixtures could probably be linked to its dual effects, namely, adsorption and degradation. TiO₂ has been reported to be highly favourable in photocatalytic treatments [37]. Meanwhile, the MSB could have acted as an adsorbent in the fabricated TiO₂/MSB mixtures to improve the affinity of TiO₂ towards the organic pollutants [38]. Ngamsopasiriskun et al. [11] reported that TiO₂/commercial activated carbon (AC) showed a synergistic effect between TiO₂ and AC in achieving 68.03% of phenol degradation after 4 h of treatment. As the 0.2 g/L TiO₂/1% MSB mixture was considered as an optimum mixture based on the obtained percentage of COD removal, this mixture was chosen to further investigate sago wastewater degradation by varying two other parameters, namely, dosage and contact time via RSM study.

3.3. Model Fitting

Based on the CCD, 13 sets of experiments with different operating conditions were conducted to investigate the effects of the independent variables (dosage of TiO₂/MSB mixture and contact time) in the photocatalytic treatment of sago wastewater (Table 2). The experimental response (), which is the percentage of COD removal, was chosen to determine the optimal conditions for the independent variables, which may affect the efficiency of the photocatalytic treatment. The complete 13 sets of experimental design matrices and responses based on the experimental results and predicted values of COD removal proposed by CCD are tabulated in Table 4. The resulting second-order polynomial equation was generated and the equation, in terms of the coded factors, is shown as

As shown in Table 4, the obtained percentage of COD removal efficiencies varied from 14.90% to 55.78% and the predicted values from the model matched these experimental results satisfactorily, as seen in Figure 10. The figure also depicts a regression coefficient () value of 0.99, which confirmed the reasonably good agreement between the experimental and predicted values. The slope for Figure 10 was 0.9997. Therefore, the developed model is suitable to predict COD removal in sago wastewater treatment.

3.4. Statistical Analysis

ANOVA is defined as a statistical technique that subdivides the total variation in a set of data into component parts related to specific variation sources to test the hypotheses on the parameters of the model [39]. Due to the regression and mean square residual error, ANOVA was used to determine the statistical significance of the ratio of mean square variation. Table 5 shows the ANOVA results for the second-order equation used to fit the COD removal from sago wastewater. As shown in the table, the -values were high for all regressions. The large -values indicated that most of the variations in the responses can be interpreted by the regression equation.

The ANOVA results for COD removal from sago wastewater using TiO₂/MSB mixture produced an -value of 1,019.22 for the quadratic model, indicating that the model is significant. The “Prob. > ” (<0.0001) for the second-order polynomial fitting implied that the model terms were significant at 95% probability level. The adequacy of the model was tested via the “lack-of-fit -tests” [40]. The “lack of fit -value” of 0.33 implied that the lack of fit was not significant, relative to the pure error. There was an 80.76% chance that a “lack-of-fit -value” could occur due to noise. The insignificant “lack of fit” demonstrated that the model is adequate. The ANOVA results for the COD removal () showed a significant () response surface model with high value of 0.9986. The adjusted value of 0.9976 and predicted value of 0.9964 were found to be at the maximum, indicating that the quadratic model provided an excellent interpretation of the relationship between the independent variables and the corresponding response. Adequate (adeq.) precision measures the signal-to-noise ratio or, in other words, is a measure of the range in predicted response relative to its associated error. The desired ratio of adequate precision is >4 [41]. The adequate precision ratio of 91.919 showed an adequate signal (Table 5). Hence, based on the ANOVA results, this quadratic model (see (3)) could be used to navigate the design space. Low coefficient of variance (CV) value of 2.47% emphasised the good precision and reliability of the experiments. It is known that the greater the value of CV, the lower or poorer the reliability of the experiment [42].

3.4.1. Effect of Dosage and Contact Time on COD Removal Percentage

The three-dimensional (3D) response surface and the two-dimensional (2D) contour plots of the model-predicted responses were obtained using the Design-Expert software. From these plots, two variables that vary within the experimental ranges were plotted and utilised to assess the interactive relationships between the variables and the response for TiO₂ photocatalysis of sago wastewater.

Figures 11(a) and 11(b) illustrate the 3D surface and 2D plot of the polynomial model, respectively, for COD removal, with respect to the dosage of TiO₂/MSB mixture and contact time during the photocatalytic treatment. The obtained 3D surface plot depicts that the highest COD removal of 52.63% would be achieved in 120 min using 0.10 g of TiO₂/MSB mixture (Figure 11(a)). It is evident that COD removal increased with increasing contact time for each TiO₂/MSB mixture dosage investigated (0.10 g to 0.30 g). A low dosage of 0.10 g demonstrated a significant increase in the COD removal as the contact time increased, which was different from the trend observed for the high dosage of 0.30 g (Figure 11(a)). In the case of photoreaction over high dosage of TiO₂/MSB mixture, the intermediates or degradation products that remained in the suspension could still be structurally similar to the initial organic compounds. Their concentrations and photostability might also differ depending on the applied dosage. The applied contact time might be too short to achieve complete oxidation [43].

(a)

(b)

On the other hand, the percentage of COD removal declined at the tested contact times (30–120 min) when the dosage of TiO₂/MSB mixture was increased from 0.10 g to 0.30 g (Figure 11(a)). The lowest COD removal of 15.14% was attained at 30 min using the highest dosage of TiO₂/MSB mixture, 0.30 g. COD removal, however, remained almost constant despite an increase in the contact time from 30 min to 120 min. The reduction of COD removal at a higher dosage of TiO₂/MSB mixture could be explained by several facts. An increased level of suspension turbidity as a result of excessive photocatalyst dosage could block the UV irradiation required for the catalyst activation [44]. Hence, it is crucial to optimise the dosage of TiO₂/MSB mixture and contact time to maximise COD removal in sago wastewater.

3.5. The Proposed Mechanism of TiO₂/MSB Photocatalytic Degradation

Typically, the photocatalytic degradation process involves three steps: adsorption of organic pollutant on the TiO₂ surface, surface photodegradation of organic pollutant, and final product desorption from the TiO₂ surface [9, 45]. In the TiO₂/MSB photocatalytic oxidation process, the reaction was activated by the absorption of photons with sufficient energy corresponding to the bandgap energy of the photocatalyst, TiO₂. Upon UV irradiation, TiO₂ particles on the MSB surface will interact with UV light to promote an electron () from the valence band to the conduction band, thus generating a positive hole () in the valence band (see (5)). The pertaining reactions at the TiO₂ surface, which govern the degradation of organic pollutants, are expressed by the following equations [44]:where is the pollutant molecule and hv is the photon energy required to excite the electron from the valence band (VB) to the conduction band (CB). Since MSB acts as an adsorbent, it is anticipated that the accumulated pollutants and intermediates on its surface will be oxidised by the photoactivated TiO₂ into simpler products, such as CO₂, H₂O, and other degradation products (see (10)). Figure 12 illustrates the proposed photoinduced mineralisation of organic pollutants using TiO₂/MSB mixture. The synergistic effects, adsorption, and photocatalysis exhibited by TiO₂/MSB mixture would aid the degradation of organic pollutants in sago effluent.

3.6. Kinetic Evaluation

The kinetics of COD degradation for sago wastewater were analysed using the first-order model as expressed in [46]where represents the apparent rate constant of the first-order reaction (min⁻¹), is the equilibrium COD of sago wastewater after adsorption in the dark, and represents the remaining COD of sago wastewater at fixed irradiation time interval. Table 6 shows the kinetics of COD degradation for sago wastewater during different treatments performed. The highest rate constants produced by 0.2 g/L TiO₂/1% MSB mixture confirmed the synergistic effects of adsorption and photocatalysis compared to the individual effects of SB, MSB, and TiO₂.

3.7. Optimisation Analysis and Verification of the Results

The optimisation process was performed using RSM, with the objective of identifying the optimum conditions for TiO₂/MSB photocatalysis, which were to minimise the usage of TiO₂/MSB and to reduce the contact time. The optimisation process was conducted by verifying the desired target for each of the variables and responses. Thus, the process variables, namely, the dosage of TiO₂/MSB and the contact time, were chosen to be “in range,” while a “target” was declared as the desired target for the COD removal to achieve the highest performance. Table 7 lists the optimum conditions derived from the statistical software.

As shown in Table 7, it has been predicted that 52.34% of COD can be removed by means of photocatalytic treatment under optimum TiO₂/MSB dosage and contact time of 0.10 g and 120 min, respectively. A series of experiments were conducted to validate the predicted response from the optimisation process. Average percentage removal of COD of 52.83% was achieved from the duplicate experiments. The effective stirring of the treatment solution may have maintained sufficient oxygen level and also contributed to the obtained COD removal. Table 8 compares the efficiency of the experimental and predicted COD removal under the established optimum conditions. The actual experimental values of COD removal were only marginally different from the predicted values. The validity of the developed polynomial model was thus verified for the photocatalytic removal of COD using the fabricated mixture material.

Under the optimum conditions, the COD of the treated sago wastewater was reduced from the initial value of 2,956.80 mg/L to 1,056.00 mg/L after 120 min of treatment (Figure 13). The COD result revealed that the TiO₂/MSB mixture was effective in reducing the COD level in sago wastewater. However, the TOC level of the treated sago wastewater had demonstrated an increase from 850.00 mg/L to 1,050.00 mg/L during the first 60 min and was reduced to 900.00 mg/L after 120 min (Figure 13). The presence of soluble organic compounds, such as hemicelluloses and lignin, in the SB, which were not fully removed during the acid pretreatment, could have contributed to the increase of TOC level [19]. Thus, the increase of TOC might be due to the leaching of organic materials from the MSB. It was also notable that the initial TOC and the final TOC levels showed no significant difference despite the changes observed, as previously explained (Figure 13). This thus implies that a more stringent oxidising condition and a longer reaction time might be needed to significantly reduce the TOC level due to the presence of intermediates and degradation products with differing nature [47]. Generally, the COD value can be considered to be more accurate in the determination of wastewater treatment efficiency compared to the TOC level [48]. COD measures the oxygen required to oxidise the organic compounds in wastewater, while TOC measures the amount of carbon in wastewater, including dissolved CO₂ and carbon compounds, such as amine and aromatic compounds [47]. The final COD obtained revealed that the sago wastewater was less suitable to be discharged into the river as the law requirement for COD is 200 mg/L [49]. Future studies will be performed to improve the applied treatment to produce an effluent that fits the required value.

3.8. Comparison of TiO₂ Photocatalysis under Different Conditions

The presence of O₂ is known to enhance the degradation of wastewater in the TiO₂ photocatalytic treatment as it can inhibit the recombination of electron-hole pairs and produces more HO∙ radicals during photocatalysis [50]. Experiments were performed to investigate the effect of O₂ on the degradation of sago wastewater using the optimised TiO₂/MSB mixture. An air diffuser was used to continuously supply aeration during the photocatalytic treatment. Raw SB (without chemical modification) was also used to prepare TiO₂/SB mixture, in the same way as the optimised 0.2 g/L TiO₂/1% MSB mixture. Figure 14 shows the percentage of COD removal achieved under different conditions. Under the aerated condition, COD removal was observed to positively increase to 63.89% compared to the 52.83% under nonaerated condition using the same TiO₂/MSB mixture. Aljuboury et al. [44] reported that the presence of air bubbling as a source of oxygen had markedly increased the degradation rate of COD in petroleum wastewater by 12%. A maximum 76% of COD removal was also achieved using TiO₂/ZnO/air system [44].

The role of O₂ in photocatalysis includes being an electron acceptor, getting involved in the formation of other oxidative species (e.g., hydroxyl radical, superoxide radical, and hydrogen peroxide), and preventing reduction reactions [51]. O₂ can also act as electron scavenger to prevent the recombination of photogenerated electron-hole pairs, which could reduce the photocatalytic activity of TiO₂/MSB [3, 34]. The photogenerated electrons () scavenged by the adsorbed molecular oxygen on the TiO₂/MSB surfaces produce ∙OH radicals as shown in (12) and (13) [52] The ∙O₂H radical can further generate H₂O₂ (see (14)) and, subsequently, HO∙ radicals (see (14)–(17)), thus preventing the recombination of electron-hole pairs, which are known to cause low TiO₂ photocatalytic quantum yield.

When the recombination rate of photogenerated electron-hole pairs is reduced, positive holes can either directly oxidise the organic pollutants or react with OH^- anions to form powerful HO∙ radicals. This would aid and promote the reduction of COD because more organic material in the sago effluent can be oxidised to its simpler form. Hence, COD level in sago effluent can be reduced by supplying O₂ via aeration, which is an economical way for continuously supplying O₂ to enhance the TiO₂ photocatalytic treatment of sago effluent. Additionally, operating costs can be reduced if air is used instead of pure oxygen in pilot scale treatments [34].

Another TiO₂ mixture, which was prepared using raw SB as an adsorbent, had yielded only 43.75% COD removal. This finding appeared consistent with those obtained by Acar and Eren [53], whereby acid-treated poplar sawdust (a plant waste) had produced appreciably better removal of Cu²⁺ at 92.38%, compared to the untreated sample, which had only removed 47.05% of Cu²⁺. It was reported that the improved adsorption efficiency exhibited by the acid-treated poplar sawdust had contributed to the increased percentage of Cu²⁺ removal. Limitations arising from the usage of untreated plant wastes as adsorbents have been reported in the literature, for instance, low adsorption capacity and high BOD, COD, and TOC values due to the release of soluble organic compounds from the untreated plant materials [19].

4. Conclusion

TiO₂/MSB mixture was prepared by mixing TiO₂ with the MSB. Six different TiO₂/MSB mixture samples were prepared to treat sago wastewater by varying the concentrations of TiO₂ and MSB. Maximum removal of 64.92% was achieved with an optimum loading of 0.2 g/L TiO₂/1% MSB after 120 min of irradiation. The dosage and contact time were fixed as the independent variables, while COD removal percentage was chosen as the dependent variable or response. Under the optimised RSM condition, 52.83% COD removal was attained using 0.10 g TiO₂/MSB mixture and contact time of 120 min. The efficiency of the optimised TiO₂/MSB mixture was found to be appreciably enhanced in the presence of aeration, which increased the COD removal of sago wastewater to 63.89%. Thus, based on the proposed mechanism, the efficiency of the TiO₂/MSB mixture was attributed to its dual functions, namely, the adsorption capacity of the MSB and the photocatalytic activity of TiO₂. The value of the model () depicted a high degree of correlation between the parameters. Thus, TiO₂ photocatalytic treatment can be a potential method for sago wastewater degradation using TiO₂/MSB.

Conflicts of Interest

The authors declare that there are no conflicts of interest regarding the publication of this article.

Acknowledgments

This study was supported by research grants from the Ministry of Higher Education, Malaysia, under the Research Acculturation Collaboration Effort (RACE) with Grant no. RACE/b/1245/201(01) and the Fundamental Research Grant Scheme [FRGS/SG01 (01)/1204/2014(05)]. The authors wish to thank UNIMAS for sponsoring the Zamalah Postgraduate Scholarship and the financial support, Mybrain 15 Scholarship, by the Malaysian government.

References

A. R. Yazdanbakhsh, A. S. Mohammadi, M. Sardar, H. Godini, and M. Almasian, “Cod removal from synthetic wastewater containing azithromycin using combined coagulation and a fenton-like process,” Environmental Engineering and Management Journal, vol. 13, no. 12, pp. 2929–2936, 2014.
View at: Google Scholar
S. H. Y. S. Abdulah, M. A. A. Hassan, Z. Z. Noor, and A. Aris, “Optimization of photo-Fenton oxidation of sulfidic spent caustic by using response surface methodology,” in Proceedings of the 3rd National Postgraduate Conference - Energy and Sustainability: Exploring the Innovative Minds, NPC 2011, Malaysia, September 2011.
View at: Publisher Site | Google Scholar
D. Kanakaraju, B. D. Glass, and M. Oelgemöller, “Titanium dioxide photocatalysis for pharmaceutical wastewater treatment,” Environmental Chemistry Letters, vol. 12, no. 1, pp. 27–47, 2014.
View at: Publisher Site | Google Scholar
P. Kumar, S. Kumar, N. K. Bhardwaj, and S. Kumar, “Titanium dioxide photocatalysis for the pulp and paper industry wastewater treatment,” Indian Journal of Science and Technology, vol. 4, no. 3, pp. 327–332, 2011.
View at: Publisher Site | Google Scholar
H. Dong, G. Zeng, L. Tang et al., “An overview on limitations of TiO₂-based particles for photocatalytic degradation of organic pollutants and the corresponding countermeasures,” Water Research, vol. 79, pp. 128–146, 2015.
View at: Publisher Site | Google Scholar
A. Fujishima, X. Zhang, and D. A. Tryk, “TiO₂ photocatalysis and related surface phenomena,” Surface Science Reports, vol. 63, no. 12, pp. 515–582, 2008.
View at: Publisher Site | Google Scholar
M. N. Chong, B. Jin, C. W. K. Chow, and C. Saint, “Recent developments in photocatalytic water treatment technology: a review,” Water Research, vol. 44, no. 10, pp. 2997–3027, 2010.
View at: Publisher Site | Google Scholar
R. Fagan, D. E. McCormack, D. D. Dionysiou, and S. C. Pillai, “A review of solar and visible light active TiO2 photocatalysis for treating bacteria, cyanotoxins and contaminants of emerging concern,” Materials Science in Semiconductor Processing, vol. 42, pp. 2–14, 2016.
View at: Publisher Site | Google Scholar
L. Giraldo and J. C. Moreno-Pirajan, “Activated carbon prepared from orange peels coated with titanium oxide nanoparticles: Characterization and applications in the decomposition of NOx,” Oriental Journal of Chemistry, vol. 30, no. 2, pp. 451–461, 2014.
View at: Publisher Site | Google Scholar
S. M. Gupta and M. Tripathi, “A review of TiO₂ nanoparticles,” Chinese Science Bulletin, vol. 56, no. 16, pp. 1639–1657, 2011.
View at: Publisher Site | Google Scholar
C. Ngamsopasiriskun, S. Charnsethikul, S. Thachepan, and A. Songsasen, “Removal of phenol in aqueous solution by nanocrystalline TiO₂/activated carbon composite catalyst,” Kasetsart Journal: Natural Science, vol. 44, no. 6, pp. 1176–1182, 2010.
View at: Google Scholar
D. S. Awg-Adeni, S. Abd-Aziz, K. Bujang, and M. A. Hassan, “Bioconversion of sago residue into value added products,” African Journal of Biotechnology, vol. 9, no. 14, pp. 2016–2021, 2010.
View at: Google Scholar
A. Muthukumar and M. Muthuchamy, “Contribution of ozone, pH and temperature in the inactivation of a foodborne pathogen Listeria monocytogenes- A study using response surface methodology,” International Journal on Applied Bio-Engineering, vol. 8, no. 1, pp. 5–13, 2014.
View at: Publisher Site | Google Scholar
APHA, Standard Methods for the Examination of Water and Wastewater, 18th, Ed., America Public Health Association, Washington, Wash, USA, 1999.
S. Ethaib, R. Omar, M. K. S. Mazlina, A. B. D. Radiah, and S. Syafiie, “Microwave-assisted dilute acid pretreatment and enzymatic hydrolysis of sago palm bark,” Bioresources, vol. 11, no. 3, pp. 5687–5702, 2016.
View at: Publisher Site | Google Scholar
A. Kristiani, H. Abimanyu, A. H. Setiawan, Sudiyarmanto, and F. Aulia, “Effect of pretreatment process by using diluted acid to characteristic of oil palm's frond,” in Proceedings of the International Conference on Sustainable Energy Engineering and Application, ICSEEA 2012, pp. 183–189, Indonesia, November 2012.
View at: Publisher Site | Google Scholar
N. Mosier, C. Wyman, B. Dale et al., “Features of promising technologies for pretreatment of lignocellulosic biomass,” Bioresource Technology, vol. 96, no. 6, pp. 673–686, 2005.
View at: Publisher Site | Google Scholar
Y. Zheng, Z. Pan, and R. Zhang, “Overview of biomass pretreatment for cellulosic ethanol production,” International Journal of Agricultural and Biological Engineering, vol. 2, no. 3, pp. 51–68, 2009.
View at: Publisher Site | Google Scholar
W. S. Wan Ngah and M. A. K. M. Hanafiah, “Removal of heavy metal ions from wastewater by chemically modified plant wastes as adsorbents: a review,” Bioresource Technology, vol. 99, no. 10, pp. 3935–3948, 2008.
View at: Publisher Site | Google Scholar
M. A. Tony and Z. Bedri, “Experimental Design of Photo-Fenton Reactions for the Treatment of Car Wash Wastewater Effluents by Response Surface Methodological Analysis,” Advances in Environmental Chemistry, vol. 2014, pp. 1–8, 2014.
View at: Publisher Site | Google Scholar
K. Yetilmezsoy, S. Demirel, and R. J. Vanderbei, “Response surface modeling of Pb(II) removal from aqueous solution by Pistacia vera L.: Box-Behnken experimental design,” Journal of Hazardous Materials, vol. 171, no. 1-3, pp. 551–562, 2009.
View at: Publisher Site | Google Scholar
V. Sangeetha, V. Sivakumar, A. Sudha, and K. S. Priyenka Devi, “Optimization of process parameters for COD removal by coagulation treatment using box-behnken design,” International Journal of Engineering and Technology, vol. 6, no. 2, pp. 1053–1058, 2014.
View at: Google Scholar
D. A. D. A. Aljuboury, P. Palaniandy, H. B. A. Aziz, and S. Feroz, “Evaluation of the solar photo-Fenton process to treat the petroleum wastewater by response surface methodology (RSM),” Environmental Earth Sciences, vol. 75, no. 4, article no. 333, pp. 1–12, 2016.
View at: Publisher Site | Google Scholar
A. Kumar, B. Prasad, and I. M. Mishra, “Process parametric study for ethene carboxylic acid removal onto powder activated carbon using Box-Behnken design,” Chemical Engineering & Technology, vol. 30, no. 7, pp. 932–937, 2007.
View at: Publisher Site | Google Scholar
I. Arslan-Alaton, G. Tureli, and T. Olmez-Hanci, “Treatment of azo dye production wastewaters using Photo-Fenton-like advanced oxidation processes: Optimization by response surface methodology,” Journal of Photochemistry and Photobiology A: Chemistry, vol. 202, no. 2-3, pp. 142–153, 2009.
View at: Publisher Site | Google Scholar
F.-S. Zhang and H. Itoh, “Photocatalytic oxidation and removal of arsenite from water using slag-iron oxide-TiO2 adsorbent,” Chemosphere, vol. 65, no. 1, pp. 125–131, 2006.
View at: Publisher Site | Google Scholar
G. Wang, L. Xu, J. Zhang, T. Yin, and D. Han, “Enhanced photocatalytic activity of TiO₂ powders (P25) via calcination treatment,” International Journal of Photoenergy, vol. 2012, Article ID 265760, 2012.
View at: Publisher Site | Google Scholar
K. Sathasivam and M. R. H. Mas Haris, “Adsorption kinetics and capacity of fatty acid-modified banana trunk fibers for oil in water,” Water, Air, & Soil Pollution, vol. 213, no. 1-4, pp. 413–423, 2010.
View at: Publisher Site | Google Scholar
S. Vitolina, G. Shulga, B. Neiberte et al., “The efficiency of biomass removal from model woodworking wastewater with polyethylenimine,” in Proceedings of the The 9th International Conference "Environmental Engineering 2014", Vilnius, Lithuania, May 2014.
View at: Publisher Site | Google Scholar
G. Hegde, S. A. Abdul Manaf, A. Kumar et al., “Biowaste Sago Bark Based Catalyst Free Carbon Nanospheres: Waste to Wealth Approach,” ACS Sustainable Chemistry & Engineering, vol. 3, no. 9, pp. 2247–2253, 2015.
View at: Publisher Site | Google Scholar
D. Kanakaraju, S. Ravichandar, and Y. C. Lim, “Combined effects of adsorption and photocatalysis by hybrid TiO2/ZnO-calcium alginate beads for the removal of copper,” Journal of Environmental Sciences, vol. 55, pp. 214–223, 2017.
View at: Publisher Site | Google Scholar
M. M. Abou-Sekkina, M. A. Sakran, and A. A. Saafan, “Development of correlations among the spectral, structural, and electrical properties and chemical treatment of Egyptian cotton fabric strips,” Industrial & Engineering Chemistry Product Research and Development, vol. 25, no. 4, pp. 676–680, 1986.
View at: Publisher Site | Google Scholar
O. Carp, C. L. Huisman, and A. Reller, “Photoinduced reactivity of titanium dioxide,” Progress in Solid State Chemistry, vol. 32, no. 1-2, pp. 33–177, 2004.
View at: Publisher Site | Google Scholar
P. R. Gogate and A. B. Pandit, “A review of imperative technologies for wastewater treatment I: oxidation technologies at ambient conditions,” Advances in Environmental Research, vol. 8, no. 3-4, pp. 501–551, 2004.
View at: Publisher Site | Google Scholar
U. I. Gaya and A. H. Abdullah, “Heterogeneous photocatalytic degradation of organic contaminants over titanium dioxide: a review of fundamentals, progress and problems,” Journal of Photochemistry and Photobiology C: Photochemistry Reviews, vol. 9, no. 1, pp. 1–12, 2008.
View at: Publisher Site | Google Scholar
G. Li Puma, A. Bono, and J. G. Collin, “Preparation of titanium dioxide photocatalyst loaded onto activated carbon support using chemical vapor deposition: A review paper,” Journal of Hazardous Materials, vol. 157, no. 2-3, pp. 209–219, 2008.
View at: Publisher Site | Google Scholar
Y. Liu, S. Yang, J. Hong, and C. Sun, “Low-temperature preparation and microwave photocatalytic activity study of TiO₂-mounted activated carbon,” Journal of Hazardous Materials, vol. 142, no. 1-2, pp. 208–215, 2007.
View at: Publisher Site | Google Scholar
F. Xu, G. Cheng, S. Song, Y. Wei, and R. Chen, “Insights into Promoted Adsorption Capability of Layered BiOCl Nanostructures Decorated with TiO₂ Nanoparticles,” ACS Sustainable Chemistry & Engineering, vol. 4, no. 12, pp. 7013–7022, 2016.
View at: Publisher Site | Google Scholar
M. Kumar, F. I. A. Ponselvan, J. R. Malviya, V. C. Srivastava, and I. D. Mall, “Treatment of bio-digester effluent by electrocoagulation using iron electrodes,” Journal of Hazardous Materials, vol. 165, no. 1-3, pp. 345–352, 2009.
View at: Publisher Site | Google Scholar
M. Hadavifar, A. A. Zinatizadeh, H. Younesi, and M. Galehdar, “Fenton and photo-Fenton treatment of distillery effluent and optimization of treatment conditions with response surface methodology,” Asia-Pacific Journal of Chemical Engineering, vol. 5, no. 3, pp. 454–464, 2010.
View at: Publisher Site | Google Scholar
R. L. Mason, R. F. Gunst, and J. L. Hess, Statistical design and analysis of experiments, Wiley Series in Probability and Statistics, Wiley-Interscience [John Wiley & Sons], USA, Hoboken, NJ, USA, 2nd edition, 2003.
View at: MathSciNet
B. Sadler, Light metals 2013, John Wiley Sons, Hoboken, NJ, USA, 2013.
J. C. Costa and M. M. Alves, “Posttreatment of olive mill wastewater by immobilized TiO₂ photocatalysis,” Photochemistry and Photobiology, vol. 89, no. 3, pp. 545–551, 2013.
View at: Publisher Site | Google Scholar
D. A. D. A. Aljuboury, P. Palaniandy, H. B. A. Aziz, S. Feroz, and S. S. A. Amr, “Evaluating photo-degradation of COD and TOC in petroleum refinery wastewater by using TiO₂/ZnO photo-catalyst,” Water Science and Technology, vol. 74, no. 6, pp. 1312–1325, 2016.
View at: Publisher Site | Google Scholar
S. Yao, J. Li, and Z. Shi, “Immobilization of TiO₂ nanoparticles on activated carbon fiber and its photodegradation performance for organic pollutants,” Particuology, vol. 8, no. 3, pp. 272–278, 2010.
View at: Publisher Site | Google Scholar
A. Omri and M. Benzina, “Almond shell activated carbon: adsorbent and catalytic support in the phenol degradation,” Environmental Modeling & Assessment, vol. 186, no. 6, pp. 3875–3890, 2014.
View at: Publisher Site | Google Scholar
D. a. Aljuboury, P. Palaniandy, H. B. Abdul Aziz, and S. Feroz, “Evaluating the TiO₂ as a solar photocatalyst process by response surface methodology to treat the petroleum waste water,” Karbala International Journal of Modern Science, vol. 1, no. 2, pp. 78–85, 2015.
View at: Publisher Site | Google Scholar
D. Kanakaraju, C. A. Motti, B. D. Glass, and M. Oelgemöller, “Solar photolysis versus TiO₂-mediated solar photocatalysis: a kinetic study of the degradation of naproxen and diclofenac in various water matrices,” Environmental Science and Pollution Research, vol. 23, no. 17, pp. 17437–17448, 2016.
View at: Publisher Site | Google Scholar
Department of Environment (DOE), Environmental Requirements: A Guide for Investor, Environmental Requirements: A Guide for Investor, Putrajaya, Malaysia, 11th edition, 2010.
M. Yasmina, K. Mourad, S. H. Mohammed, and C. Khaoula, “Treatment heterogeneous photocatalysis; Factors influencing the photocatalytic degradation by TiO₂,” in Proceedings of the International Conference on Technologies and Materials for Renewable Energy, Environment and Sustainability, TMREES 2014 - EUMISD, pp. 559–566, Lebanon, April 2014.
View at: Publisher Site | Google Scholar
S. Malato, P. Fernández-Ibáñez, M. I. Maldonado, J. Blanco, and W. Gernjak, “Decontamination and disinfection of water by solar photocatalysis: recent overview and trends,” Catalysis Today, vol. 147, no. 1, pp. 1–59, 2009.
View at: Publisher Site | Google Scholar
P. A. Pekakis, N. P. Xekoukoulotakis, and D. Mantzavinos, “Treatment of textile dyehouse wastewater by TiO₂ photocatalysis,” Water Research, vol. 40, no. 6, pp. 1276–1286, 2006.
View at: Publisher Site | Google Scholar
F. N. Acar and Z. Eren, “Removal of Cu(II) ions by activated poplar sawdust (Samsun Clone) from aqueous solutions,” Journal of Hazardous Materials, vol. 137, no. 2, pp. 909–914, 2006.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2018 Devagi Kanakaraju and Soon Pang Wong. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

3294

Downloads

1411

Citations

Journal of Chemistry

Photocatalytic Efficiency of TiO2-Biomass Loaded Mixture for Wastewater Treatment

Abstract

1. Introduction

2. Materials and Methods

2.1. Materials

2.2. Sago Wastewater

2.3. Analytical Determinations

2.4. Synthesis of TiO2 Mixtures (TiO2/MSB)

2.5. Material Characterisations

2.6. Photocatalytic Experiment

2.7. Experimental Design

3. Results and Discussion

3.1. Characterisation of TiO2/MSB Mixture

3.2. Photodegradation of Wastewater

3.3. Model Fitting

3.4. Statistical Analysis

3.4.1. Effect of Dosage and Contact Time on COD Removal Percentage

3.5. The Proposed Mechanism of TiO2/MSB Photocatalytic Degradation

3.6. Kinetic Evaluation

3.7. Optimisation Analysis and Verification of the Results

3.8. Comparison of TiO2 Photocatalysis under Different Conditions

4. Conclusion

Conflicts of Interest

Acknowledgments

References

Copyright

Photocatalytic Efficiency of TiO₂-Biomass Loaded Mixture for Wastewater Treatment

2.4. Synthesis of TiO₂ Mixtures (TiO₂/MSB)

3.1. Characterisation of TiO₂/MSB Mixture

3.5. The Proposed Mechanism of TiO₂/MSB Photocatalytic Degradation

3.8. Comparison of TiO₂ Photocatalysis under Different Conditions