CH<sub>4</sub>/N<sub>2</sub> Adsorptive Separation on Zeolite X/AC Composites

Xue, Cai Long; Cheng, Wen Ping; Hao, Wen Ming; Ma, Jing Hong; Li, Rui Feng

doi:https://doi.org/10.1155/2019/2078360

Journal of Chemistry

On this page

Abstract Introduction Experimental Results and Discussion Conclusions Data Availability Conflicts of Interest Acknowledgments References Copyright Related Articles

Research Article | Open Access

Volume 2019 | Article ID 2078360 | https://doi.org/10.1155/2019/2078360

CH₄/N₂ Adsorptive Separation on Zeolite X/AC Composites

Cai Long Xue,¹Wen Ping Cheng,¹Wen Ming Hao,¹Jing Hong Ma,¹and Rui Feng Li¹

Academic Editor: Philippe Trens

Received26 Sept 2018

Accepted21 Nov 2018

Published02 Jan 2019

Abstract

A series of zeolite X/activated carbon (AC) composites were prepared from the same starting materials at various activation time. The corresponding modified samples were obtained by being treated with diluted NH₄Cl solution. The relationship between porosity development, surface properties, and CH₄/N₂ adsorption performance was investigated. The increase of micropore volume is beneficial to the improvement of CH₄ and N₂ adsorption capacity, but more sensitive for CH₄. In addition, the polar functional groups of zeolite X/AC composites may enhance CH₄ adsorption capacity. More importantly, both developing micropore structure and surface modification contributed to enhance the adsorption selectivity . As the optimum sample of these studies, HZAC(24) showed CH₄ adsorption capacity of 17.3 cm³/g and the highest adsorption selectivity of 3.4. The CH₄ and N₂ adsorption isotherms of all samples can be well fitted by the Langmuir–Freundlich model. HZAC(24) showed an excellent cyclability of adsorption/desorption of CH₄ with a neglectable capacity loss after subsequent cycles. Moreover, HZAC(24) displayed relatively rapid adsorption kinetics. These properties of zeolite X/AC composites are essential for the adsorptive separation of CH₄ from N₂ in the pressure swing adsorption (PSA) process.

1. Introduction

The coal bed methane (CBM) is an unconventional gas with a main composition of CH₄, N₂, and CO₂, which reserve is about two times higher than that known to natural gas [1]. Nowadays, due to the CH₄ content in the drainage gas of coal mine is only 20–45%, CBM is usually extracted into the atmosphere, which not only is a waste of energy source but also pollutes the environment as CH₄ is one of the major contributors to the global warming with 20 times higher global warming potential than that of CO₂ [2, 3]. So, it is of great significance to develop and utilize the CBM. The content of CH₄ higher than 80% is required for the application of chemical raw stock and 90% for merging into the civil gas system [4]. For pipeline quality natural gas, the impurities of N₂ and CO₂ content should not exceed 4% and 2%, respectively [5, 6]. So, CH₄ separation from N₂ and CO₂ is one of the important industrial separation processes [7, 8]. However, CH₄ and N₂ possess extremely similar physicochemical properties and kinetic diameter. Therefore, it is a really large challenge to enrich CH₄ from the mixture of CH₄ and N₂ such as CBM.

Generally, membrane [9], cryogenic [10, 11], and adsorption separation [12] are applied to separate the CH₄ and N₂ mixture. Membrane separation has the drawbacks of low selectivity and the strongly dependence of the membrane which is liable to damage and block; thus, it is not economical in scale separation [13, 14]. Cryogenic separation requires high-energy consumption and is helpless for low flow rates. In comparison with other methods, adsorption separation with easy operation, lower energy requirement, lower operational cost, running continuous at ambient temperature, and so on attracts increasingly attention. During the past three decades, there has been a rapid growth in the development of adsorption-based technologies for separation and purification of different gas mixtures, so that it can be applied to medium-scale CH₄/N₂ separation. However, it is still a big challenge as for the larger-scale CH₄/N₂ adsorption separation due to the lack of satisfactory adsorbent with high adsorption capacity and selectivity.

Many materials have been developed for gas selective separation. Zeolites, as one of the candidates for enriching CH₄ from gas mixture, have shown great prospect and can potentially be used in the pressure swing adsorption (PSA) process. In order to obtain an appropriate zeolite for gas adsorption separation, the effect factors, including the pore structure of zeolite and the strength of the electric fields caused by the presence of exchangeable cations in the frameworks, have been investigated [5, 14]. It has been found that zeolite X [15–21] is one of the most suitable zeolite adsorbents for adsorption and separation due to its large pore diameter of 0.74 nm which can accommodate large molecules and low Si/Al ratio with the presence of extra framework of cations that produces electric field which interacts strongly with the high polarizability CH₄ molecule or quadrupolar CO₂ molecules. Activated carbon [22–24], another promising candidate for gas separation, possesses lots of advantages such as tunable pore size, easy regeneration, and low cost. In general, activated carbons have higher equilibrium selectivity for CH₄ over N₂ but smaller adsorption capacities for CH₄ than zeolites. As a consequence, in order to integrate the advantages of both zeolite and activated carbon in industrial application, increasingly attentions have been concentrated on the synthesis of the novel porous material of zeolite/AC composites in recent years [25, 26]. Meanwhile, the environmental application such as wastewater treatment as well as gas separation using of zeolite/AC composites has been explored preliminarily [27, 28]. In our previous work, the zeolite X/AC composites from elutrilithe are prepared by adding pitch powder and precipitate silicon dioxide as an additional carbonaceous and silica source, respectively [25, 29, 30].

The main aim in this work is to introduce amine modifications in a series of zeolite X/AC composites with different activation time in order to increase the interactions with CH₄ without improving those with gases. This strategy will improve the potential of these materials to separate CH₄/N₂ mixtures, making these materials candidates for natural gas upgrading. The effect of pore texture and surface properties of the adsorbents on the adsorption performance of CH₄ and N₂ was investigated in detail.

2. Experimental

2.1. Preparation of Zeolite X/AC Composites

Zeolite X/AC composites were prepared by the following two steps. First, the locally available Elutrilithe chunk, with major chemical composition of 41.0 wt.% SiO₂, 35.5 wt.% Al₂O₃, and 7.0 wt.% C, was crashed and sieved in order to collect the grains with an average size below 200 meshes. The elutrilithe powder was then simply physically mixed with precipitated silica (ca.93% SiO₂) and pitch powder in order to get a constant molecular ratio SiO₂/Al₂O₃ = 4.5 and a final mass composition of 50 wt.% carbon. The obtained blend powder was kneaded with defined amount of deionized water and extruded into a cylinder shape with dimensions of φ2.0 mm × 6.0 mm by extruder. After drying overnight, the extrudates were calcined in a tubular furnace under a stream of N₂ with a flow rate of 150 ml/min at 723 K for 2 h and following 1123 K for 2 h. After that, the temperature of 1123 K was maintained for time t_a, and the atmosphere was switched from N₂ to CO₂ (200 ml/min) for activation. t_a is a variable activation parameter, ranging from 4 h to 32 h. A heating rate of 5 K/min was applied up to the appointed temperature in the above procedure. Subsequently, the activated samples were treated with a NaOH hydrothermal system in a flash (Al₂O₃ : SiO₂ : Na₂O : H₂O = 1 : 4.5 : 4.5 : 135), and then, the products were filtered, washed with deionized water at 323–343 K until the pH of the products reached around 7, and dried at 373 K for at least 6 h. ZAC(t_a) (t_a = 4, 16, 24, and 32, which represent the activation time of 4 h, 16 h, 24 h, and 32 h) is used to mark the composites, and the corresponding burn-off of ZAC(t_a) is 42, 29, 21, and 17%, respectively.

The surface modification of the composites was carried out by the conventional soaking method. A typical soaking method involved adding 250 mL of 0.3 mol/L NH₄Cl solution to about 10 g composite. The solution was heated to 340 K for 0.5 h. After that, the solution was decanted, and fresh solution was added. This procedure was repeated three times. After modification, the samples were filtered and washed with copious amount of deionized water until the effluent was free from chloride ions as tested with AgNO₃ solution. The resulting products were dried at 373 K for more than 6 h and calcined in a tube furnace at 623 K for 2 h under vacuum to dislodge the NH₃ in the products. The corresponding products after modification were denoted as HZAC(t_a) (t_a = 4, 16, 24, and 32, which represent the activation time of 4 h, 16 h, 24 h, and 32 h).

2.2. Characterization

X-ray powder diffraction (XRD) patterns of the materials were obtained using a Shimadzu LabX XRD-6000 system in the 2θ range of 5–35° using CuKα1 (λ = 1.54056 Å) radiation operated with 40 kV and 30 mA. The surface area and pore volume of the products were calculated from N₂ adsorption isotherms measured on a surface area and pore size analyzer, QUADRASORB SI, (Quantachrome Inc., USA) after degassing the samples at 623 K for at least 4 h under high vacuum. The surface areas (S_BET) were calculated by using the Brunauer–Emmett–Teller (BET) equation at the relative pressure in the range of 0.01–0.2. The micropore volume (V_mic) and micropore surface (S_mic) area were determined by the t-plot method. The amount of N₂ absorbed at P/P₀ = 0.98 was employed to calculate the total pore volume (V_total). The total basicity of the samples was determined by temperature-programmed desorption of carbon dioxide (CO₂-TPD) using a type of TP-5076 TPR/TPD automatic temperature-programmed chemical adsorption apparatus. The surface properties of the samples were analyzed by employing a conventional Boehm titration procedure. Aqueous solutions of NaOH, HCl, Na₂CO₃, and NaHCO₃ (0.1 mol/L) with the volume of 25 mL were decanted into conical flasks with 1 g sample each, respectively, and after shaking for 1 h, the conical flasks were kept standing for 48 h, and then filtered. The filtrates were diluted and employed back titration with standard solution to calculate the amount of surface function groups on the samples.

2.3. Adsorption Measurements

The presence of water in the composites significantly affects the adsorption isotherm; therefore, all the samples were calcined at 573 K for 4 h under N₂-flow in a tubular furnace. Prior to adsorption measurements, the samples were degassed under vacuum by heating up to 623 K for at least 4 h. The CH₄ and N₂ adsorption isotherms were measured at 273 K using a static volumetric apparatus of NOVE1200e instrument (Quantachrome Inc., USA). The adsorption kinetics curve was measured by releasing a small amount of CO₂ with the type NOVE1000e instrument (Quantachrome Inc., USA). During the adsorption, measurement temperature was maintained by circulating ethanediol-water from a constant temperature bath. The adsorption capacity was determined from the adsorption isotherm measured at 273 K, and the pure component selectivity of CH₄ and N₂ () was calculated by using the following equation:where and are the adsorption amount (at 273 K, 100 kPa) of CH₄ and N₂, respectively.

3. Results and Discussion

3.1. Zeolite X/AC Composites

The XRD patterns of zeolite X/AC composites before and after modification are shown in Figure 1. It can be seen that all samples are highly crystalline materials giving the reflections in the range of 5–35° and exhibit characteristic peaks of zeolite X without other impurity phases. The crystallinity of zeolite X decreases after surface modification as evidenced from the decrease of the intensity of the major characteristic peaks of zeolite X. This is due to the partially collapse of the crystalline structure, which is consistent with the conclusion from others [31, 32].

(a)

(b)

Figure 2 displays N₂ adsorption-desorption isotherms at 77 K on a series of samples. All isotherms exhibit the characteristic combination of the type-I and type-IV morphology, indicating the coexistence of micropores and mesopores in the composites [33]. Table 1 summarizes their pore structure parameters calculated from the isotherms. It can be seen that, as far as t_a ≤ 24 h, the S_BET, S_mic, V_total, and V_mic of ZAC(t_a) samples presented a significant rising trend, and it occurred sharply decrease thereafter, while the S_ext was increasing with lengthening the activated time. This means that extending the activation time when t_a ≤ 24 h mainly induces the creation of new pores, while widening of pores becomes the main mechanism of porosity development with longer activation time [25]. In addition, the treatment of NH₄Cl solution has a significant effect on the textual properties. In comparison with ZAC(t_a), the pore structure parameters of HZAC(t_a) decrease except S_ext, due to the partially collapse of the crystalline structure in the composites during surface modification [32].

(a)

(b)

The CO₂-TPD results of ZAC(t_a) and HZAC(t_a) are shown in Figure 3. For ZAC(t_a) samples, a larger desorption peak at 573–673 K and a little shoulder peak take place at around 383 K, corresponding to the surface basic site; however, there is only one desorption peak of HZAC(t_a) samples at about 473–573 K. From Figure 3, it can be seen that CO₂ desorption peak areas increase and CO₂ desorption peak moves to higher temperature for ZAC(t_a) samples when increasing activation time, indicating that the amount and strength of surface basic groups rising, respectively. The variation tendency of the surface basic properties of HZAC(t_a) is similar with ZAC(t_a). However, both the amount of the surface basic groups and basic strength decline for HZAC(t_a) compared with ZAC(t_a), which resulted from the treatment by NH₄Cl solution. In addition, Figure 4 shows the representative Boehm titration results of ZAC(24) and HZAC(24), which shows that the basic groups decrease almost half, and phenolic, carboxylic, and the total acidic groups sharply increase. These results are similar to the reports from references [34–36].

3.2. CH₄ and N₂ Adsorption Isotherms

The pure component CH₄ and N₂ adsorption isotherms at 273 K on the samples of ZAC(t_a) and HZAC(t_a) have been generated and are given in Figure 5. All curves are found to be type-I as per the IUPAC classification, and the low-pressure adsorption isotherms behave linearly [14, 33], which is ideal for sorbent regeneration, since most of the working capacity is recovered at moderate pressure ranges. A summary of adsorption and separation parameters extracted from adsorption isotherms is presented in Table 1. It can be seen that the CH₄ adsorption capacity is higher than that of N₂ on all of the samples. The CH₄ and N₂ adsorption capacity and CH₄/N₂ adsorption selectivity increased with the increase of V_mic. After the composites being treated by NH₄Cl, both of the CH₄ and N₂ adsorption capacity on the composites decreased; however, the CH₄/N₂ adsorption selectivity increased significantly.

(a)

(b)

(c)

(d)

Equilibrium adsorption isotherms in adsorbents are required for the available modeling or simulation of the various PSA separation processes of CH₄ and N₂ in practical application. Hence, in order to extend its utility, the collected experimental adsorption isotherm data should be fitted to an isotherm model [37]. In the present work, the adsorption isotherms of CH₄ and N₂ on all samples are fitted using the conventional Langmuir–Freundlich (L-F) (equation (2)) adsorption model [38, 39]:where is the pressure, is the corresponding amount of the adsorbate adsorbed, is the saturation capacity of the adsorbent, is the adsorption affinity defined by the van’t Hoff equation for a heterogeneous solid, and is the reciprocal of the Freundlich heterogeneity factor (the larger the value, the more the deviation from the Langmuir isotherm). Both and are empirical constants to be obtained by the data fitting method. Fitted parameters of the CH₄ and N₂ adsorption isotherms for all samples with L-F models are listed in Table 2. It can be seen that the Langmuir–Freundlich model is well correlated with the experimental adsorption data over the entire pressure range studied. Obviously, the values of of CH₄ adsorption are higher than that of N₂ for ZAC(t_a), suggesting the stronger interaction between CH₄ and the samples than that between N₂ and the composites. After NH₄Cl treatment, the value of decreases for N₂ adsorption, due to a decrease in the interaction between N₂ and modified composites. However, increases for CH₄ adsorption, and the higher value of for HZAC(t_a) is due to an increase in the interaction between CH₄ and HZAC(t_a). The changes in the values of both CH₄ and N₂ adsorptions explain well the increase of the CH₄/N₂ selectivity on HZAC(t_a).

3.3. Effect of Pore Structure and Surface Properties on the Adsorption Performance

In order to improve the CH₄/N₂ adsorption selectivity and maintain the adsorption capacity of CH₄, the relationship between CH₄ and N₂ adsorption properties and the pore texture were studied in detail. ZAC(32) possesses a lower V_mic and a larger S_ext than ZAC(24), and the adsorption capacity and selectivity of CH₄ and N₂ showed the lower values on ZAC(32), indicating that the high adsorption capacity and selectivity of CH₄ and N₂ results from the large micropore volume rather than S_ext [40–45]. In Figure 6, the adsorption capacity of CH₄ and N₂ and adsorption selectivity are plotted versus V_mic. For ZAC(t_a), as the V_mic increased from 0.275 cm³/g to 0.357 cm³/g, the adsorption capacity of CH₄ and N₂ increased from 16.1 cm³/g to 22.6 cm³/g and 7.52 cm³/g to 9.39 cm³/g, respectively. When the V_mic increases from 0.196 cm³/g to 0.273 cm³/g for HZAC(t_a), the CH₄ adsorption capacity increases from 14.4 cm³/g to 17.3 cm³/g. The adsorption selectivity for ZAC(t_a) and HZAC(t_a) presents a slight rise tendency. As a summary, with the increase of V_mic, CH₄ and N₂ adsorption capacity increased, and adsorption selectivity enhances slightly at the same time. However, the CH₄ and N₂ adsorption properties of ZAC(4) are different from HZAC(24) although the values of V_mic for the two samples are similar, which suggests that the pore structure is not the only factor affecting the gases adsorption performance on the samples.

(a)

(b)

Besides pore structure, the surface properties are also considered to be a significant factor on the gas adsorption process of the studied samples. After the treatment by NH₄Cl, the basic groups decreased severely and the acidic groups including phenolic and carboxylic groups sharply increased. Although CH₄ is a nonpolar molecule, it has a higher polarizability of 26 × 10⁻²⁵ cm³ [46]. Such polarizability causes a momentary shift in the time when the neutral electrostatic field of CH₄ is in close proximity to the larger polar function groups such as phenolic and carboxylic groups within the composites. The polarizability of N₂ (17.6 × 10⁻²⁵ cm³) is much lower than that of CH₄. Hence, the increasing of polar functional groups is more conducive to enhance the interaction between CH₄ molecule and the adsorbents [32, 39, 40, 47]. The reduction of the CH₄ adsorption capacity resulted from the decrease of V_mic in HZAC(t_a) was offset partially by the increase in interaction strongly between CH₄ molecule and HZAC(t_a). These characteristics lead to a moderate decrease in CH₄ adsorption capacity and a drastic decrease in N₂ adsorption capacity after NH₄Cl treatment; therefore, the adsorption selectivity on the HZAC(t_a) is extremely higher than that on the ZAC(t_a). In conclusion, there is a positive correlation between CH₄ adsorption capacity and adsorption selectivity and the V_mic. When the V_mic of samples is similar, the CH₄ adsorption capacity and the adsorption selectivity depended on the surface properties of the samples. HZAC(24) with a considerable V_mic and a higher amount of acidic groups has satisfactory CH₄ adsorption capacity and the maximum adsorption selectivity among the studied samples.

3.4. Cycle Adsorption and Time-Dependent Adsorption Capacity of CH₄

As adsorption-driven gas separation processes depend on the cyclic regeneration of the adsorbent, it is important to study the cyclic adsorption performance of the adsorbents during long-term cyclical operation [48]. The successive adsorption/desorption cycles on HZAC(24) were carried out for nine times, and the results are shown in Figure 7. Within each cycle, the HZAC(24) was regenerated by reducing the pressure of CH₄ along the desorption branch and finally reached the conditions of a dynamic vacuum. The maximum CH₄ adsorbed amount was almost constant in nine cycles of adsorption and desorption, indicating that the CH₄ adsorption performance of HZAC(24) is stable. The results suggest that the zeolite X/AC composite can be easily regenerated by vacuum in the CH₄ adsorption system and be reused for many circles without any decay for the adsorption capacity.

For potential applications of zeolite X/AC composite in adsorption-driven separation of CH₄ from CH₄/N₂ mixture, it is also crucial that the adsorption of CH₄ is rapid. Typically, the industrial adsorption process is shorter than 1 min [49]. Here, we studied the time-dependent adsorption of CH₄ on HZAC(24) by releasing a small amount of CH₄ and studying the adsorbed amount as a function of time as shown in Figure 8. HZAC(24) displayed a relatively rapid adsorption kinetics, reaching 96% of the CH₄ capacity within 40 s. The rapid uptake indicates that zeolite X/AC composite can meet the requirements for an adsorbent used in the PSA process for the separation of CH₄.

4. Conclusions

Zeolite X/AC composites with different pore textures were prepared and then treated by diluted NH₄Cl solution. With the increase of activation time, the micropore volume increased, which reaches the maximum at the activation time of 24 hours. Furthermore, the increase of the micropore volume is beneficial to enhance the adsorption capacity of CH₄ and the adsorption selectivity . The increase of acidic oxygen-containing functional groups on sample surface significantly contributed to enhancing the adsorption selectivity , but leading to the decrease of the adsorption capacity of CH₄. The HZAC(24) sample showed the highest adsorption selectivity of 3.4 among the studied samples and a high CH₄ adsorption capacity of 17.3 cm³/g. The isotherms of CH₄ and N₂ on the composites before and after NH₄Cl treatment can be well fitted by the Langmuir–Freundlich model. Moreover, the HZAC(24) showed excellent cyclability of adsorption/desorption of CH₄ and relatively rapid adsorption kinetics. The present work provides a promising sight of applying zeolite X/AC composites from an economic and simple synthesis route as CH₄ adsorbent with high adsorption selectivity .

Data Availability

The data used to support the findings of this study are included within the article.

Conflicts of Interest

The authors declare that they have no conflicts of interest.

Acknowledgments

We gratefully appreciate the financial support from the National Natural Science Foundation of China (No. 51204120), Natural Science Foundation of Shanxi (No. 2014021014-1), and Key Scientific and Technological Project of Coal Fund of Shanxi province (No. FT201402-03).

References

Q. Jiang, Report on China Coal Bed Methane Industry for 2010–2015, 2010, http://www.ocn.com.cn/reports/2006131meiceng.htm.
C. A. Grande, F. V. S. Lopes, A. M. Ribeiro, J. M. Loureiro, and A. E. Rodrigues, “Adsorption of off-gases from steam methane reforming (H₂, CO₂, CH₄, CO and N₂) on activated carbon,” Separation Science and Technology, vol. 43, no. 6, pp. 1338–1364, 2008.
View at: Publisher Site | Google Scholar
F. V. S. Lopes, C. A. Grande, A. M. Ribeiro, V. J. P. Vilar, J. M. Loureiro, and A. E. Rodrigues, “Effect of ion exchange on the adsorption of steam methane reforming off-gases on zeolite 13X,” Journal of Chemical & Engineering Data, vol. 55, no. 1, pp. 184–195, 2010.
View at: Publisher Site | Google Scholar
Engelhard Corporation, Adsorption Processes for Natural Gas Treatment, A Technology Update, Engelhard Corporation, Newark, NY, USA, 2005, http://www.engelhard.com.
R. S. Pillai, G. Sethia, and R. V. Jasra, “Sorption of CO, CH₄, and N₂ in alkali metal ion exchanged zeolite-X: grand canonical Monte Carlo simulation and volumetric measurements,” Industrial & Engineering Chemistry Research, vol. 49, no. 12, pp. 5816–5825, 2010.
View at: Publisher Site | Google Scholar
R. T. Yang, “Gas Separation by Adsorption Processes,” in Chemical Engineering Science, vol. 43, Butterworth-Heinemann, Oxford, UK, 1997.
View at: Google Scholar
A. Jayaraman, A. J. Hernandez-Maldonado, R. T. Yang, D. Chinn, C. L. Munson, and D. H. Mohr, “Clinoptilolites for nitrogen/methane separation,” Chemical Engineering Science, vol. 59, no. 12, pp. 2407–2417, 2004.
View at: Publisher Site | Google Scholar
D. M. Ruthven, “Sorption of oxygen, nitrogen, carbon monoxide, methane, and binary mixtures of these gases in 5A molecular sieve,” AIChE Journal, vol. 22, no. 4, pp. 753–759, 2010.
View at: Publisher Site | Google Scholar
P. Tremblay, M. Savard, J. Vermette, and R. Paquin, “Gas permeability, diffusivity and solubility of nitrogen, helium, methane, carbon dioxide and formaldehyde in dense polymeric membranes using a new on-line permeation apparatus,” Journal of Membrane Science, vol. 282, no. 1-2, pp. 245–256, 2006.
View at: Publisher Site | Google Scholar
T. Gao, W. Lin, A. Gu, and M. Gu, “Coalbed methane liquefaction adopting a nitrogen expansion process with propane pre-cooling,” Applied Energy, vol. 87, no. 7, pp. 2142–2147, 2010.
View at: Publisher Site | Google Scholar
W. S. Gao, X. S. Lu, W. S. Lin, and A. Z. Gu, “Parameter comparison of two small-scale natural gas liquefaction processes in skid-mounted packages,” Applied Thermal Engineering, vol. 26, no. 8-9, pp. 898–904, 2005.
View at: Publisher Site | Google Scholar
R. T. Yang, Adsorbents: Fundamentals and Applications, John Wiley & Sons, Hoboken, NJ, USA, 2003.
K. S. Knaebel and H. E. Reinhold, “Landfill gas: from rubbish to resource,” Adsorption, vol. 9, no. 1, pp. 87–94, 2003.
View at: Publisher Site | Google Scholar
G. Sethia, R. S. Somani, and H. C. Bajaj, “Sorption of methane and nitrogen on cesium exchanged zeolite-X: structure, cation position and adsorption relationship,” Industrial & Engineering Chemistry Research, vol. 53, no. 16, pp. 6807–6814, 2014.
View at: Publisher Site | Google Scholar
A. Arefi Pour, S. Sharifnia, R. NeishaboriSalehi, and M. Ghodrati, “Performance evaluation of clinoptilolite and 13X zeolites in CO₂ separation from CO₂/CH₄ mixture,” Journal of Natural Gas Science and Engineering, vol. 26, pp. 1246–1253, 2015.
View at: Publisher Site | Google Scholar
F. Bandarchian and M. Anbia, “Conventional hydrothermal synthesis of nanoporous molecular sieve 13X for selective adsorption of trace amount of hydrogen sulfide from mixture with propane,” Journal of Natural Gas Science and Engineering, vol. 26, pp. 1380–1387, 2015.
View at: Publisher Site | Google Scholar
V. Garshasbi, M. Jahangiri, and M. Anbia, “Equilibrium CO₂ adsorption on zeolite 13X prepared from natural clays,” Applied Surface Science, vol. 393, pp. 225–233, 2017.
View at: Publisher Site | Google Scholar
P. Gómez-Álvarez, S. Hamad, M. Haranczyk, A. R. Ruiz-Salvador, and S. Calero, “Comparing gas separation performance between all known zeolites and their zeolitic imidazolate framework counterparts,” Dalton Transactions, vol. 45, no. 1, pp. 216–225, 2016.
View at: Publisher Site | Google Scholar
Y. Qin, Z. Mo, W. Yu et al., “Adsorption behaviors of thiophene, benzene, and cyclohexene on FAU zeolites: comparison of CeY obtained by liquid-, and solid-state ion exchange,” Applied Surface Science, vol. 292, no. 1, pp. 5–15, 2014.
View at: Publisher Site | Google Scholar
S. Salehi and M. Anbia, “Adsorption selectivity of CO₂ and CH₄ on novel PANI/Alkali-Exchanged FAU zeolite nanocomposites,” Journal of Inorganic and Organometallic Polymers and Materials, vol. 27, no. 5, pp. 1281–1291, 2017.
View at: Publisher Site | Google Scholar
A. Villarreal, G. Garbarino, P. Riani et al., “Adsorption and separation of CO₂ from N₂-rich gas on zeolites: Na-X faujasite vs Na-mordenite,” Journal of CO₂ Utilization, vol. 19, pp. 266–275, 2017.
View at: Publisher Site | Google Scholar
C. Liu, Y. Dang, Y. Zhou et al., “Effect of carbon pore structure on the CH₄/N₂ separation,” Adsorption, vol. 18, no. 3-4, pp. 321–325, 2012.
View at: Publisher Site | Google Scholar
S. Y. Sawant, K. Munusamy, R. S. Somani, M. John, B. L. Newalkar, and H. C. Bajaj, “Precursor suitability and pilot scale production of super activated carbon for greenhouse gas adsorption and fuel gas storage,” Chemical Engineering Journal, vol. 315, pp. 415–425, 2017.
View at: Publisher Site | Google Scholar
K. X. Yao, Y. Chen, Y. Lu, Y. Zhao, and Y. Ding, “Ultramicroporous carbon with extremely narrow pore distribution and very high nitrogen doping for efficient methane mixture gases upgrading,” Carbon, vol. 122, pp. 258–265, 2017.
View at: Publisher Site | Google Scholar
J. Ma, J. Tan, X. Du, and R. Li, “Effects of preparation parameters on the textural features of a granular zeolite/activated carbon composite material synthesized from elutrilithe and pitch,” Microporous and Mesoporous Materials, vol. 132, no. 3, pp. 458–463, 2010.
View at: Publisher Site | Google Scholar
M. Miyake, Y. Kimura, T. Ohashi, and M. Matsuda, “Preparation of activated carbon-zeolite composite materials from coal fly ash,” Microporous and Mesoporous Materials, vol. 112, no. 1–3, pp. 170–177, 2008.
View at: Publisher Site | Google Scholar
K. Y. Foo and B. H. Hameed, “The environmental applications of activated carbon/zeolite composite materials,” Advances in Colloid and Interface Science, vol. 162, no. 1-2, pp. 22–28, 2011.
View at: Publisher Site | Google Scholar
V. K. Jha, M. Matsuda, and M. Miyake, “Sorption properties of the activated carbon-zeolite composite prepared from coal fly ash for Ni²⁺, Cu²⁺, Cd²⁺, and Pb²⁺,” Journal of Hazardous Materials, vol. 160, no. 1, pp. 148–153, 2008.
View at: Publisher Site | Google Scholar
Z. Li, X. Cui, J. Ma, W. Chen, W. Gao, and R. Li, “Preparation of granular X-type zeolite/activated carbon composite from elutrilithe by adding pitch and solid SiO₂,” Materials Chemistry and Physics, vol. 147, no. 3, pp. 1003–1008, 2014.
View at: Publisher Site | Google Scholar
J. Ma, H. Sun, S. Su, W. Cheng, and R. Li, “A novel double-function porous material: zeolite-activated carbon extrudates from elutrilithe,” Journal of Porous Materials, vol. 15, no. 3, pp. 289–294, 2007.
View at: Publisher Site | Google Scholar
S. Lee, H. Kim, and M. Choi, “Controlled decationization of X zeolite: mesopore generation within zeolite crystallites for bulky molecular adsorption and transformation,” Journal of Materials Chemistry A, vol. 1, no. 39, p. 12096, 2013.
View at: Publisher Site | Google Scholar
D. Zhang, W. Cheng, J. Ma, and R. Li, “Influence of activated carbon in zeolite X/activated carbon composites on CH₄/N₂ adsorption separation ability,” Adsorption, vol. 22, no. 8, pp. 1129–1135, 2016.
View at: Publisher Site | Google Scholar
S. Brunauer, P. H. Emmett, and E. Teller, “Adsorption of gases in multimolecular layers,” Journal of the American Chemical Society, vol. 60, no. 2, pp. 309–319, 1938.
View at: Publisher Site | Google Scholar
X. Lu, D. Jin, S. Wei et al., “Competitive adsorption of a binary CO₂-CH₄ mixture in nanoporous carbons: effects of edge-functionalization,” Nanoscale, vol. 7, no. 3, pp. 1002–1012, 2015.
View at: Publisher Site | Google Scholar
S. K. Wirawan and D. Creaser, “CO₂ adsorption on silicalite-1 and cation exchanged ZSM-5 zeolites using a step change response method,” Microporous and Mesoporous Materials, vol. 91, no. 1–3, pp. 196–205, 2006.
View at: Publisher Site | Google Scholar
X. Xu, X. Zhao, L. Sun, and X. Liu, “Adsorption separation of carbon dioxide, methane, and nitrogen on Hβ and Na-exchanged β-zeolite,” Journal of Natural Gas Chemistry, vol. 17, no. 4, pp. 391–396, 2008.
View at: Publisher Site | Google Scholar
J. Ma, C. Si, Y. Li, and R. Li, “CO₂ adsorption on zeolite X/activated carbon composites,” Adsorption, vol. 18, no. 5-6, pp. 503–510, 2012.
View at: Publisher Site | Google Scholar
T. F. d. Oliveira, E. S. Ribeiro, M. G. Segatelli, and C. R. T. Tarley, “Enhanced sorption of Mn²⁺ ions from aqueous medium by inserting protoporphyrin as a pendant group in poly(vinylpyridine) network,” Chemical Engineering Journal, vol. 221, no. 2, pp. 275–282, 2013.
View at: Publisher Site | Google Scholar
Z. Zhao, X. Cui, J. Ma, and R. Li, “Adsorption of carbon dioxide on alkali-modified zeolite 13X adsorbents,” International Journal of Greenhouse Gas Control, vol. 1, no. 3, pp. 355–359, 2007.
View at: Publisher Site | Google Scholar
X. Cui, R. M. Bustin, and G. Dipple, “Selective transport of CO₂, CH₄, and N₂ in coals: insights from modeling of experimental gas adsorption data,” Fuel, vol. 83, no. 3, pp. 293–303, 2004.
View at: Publisher Site | Google Scholar
A. Perrin, A. Celzard, A. Albiniak, J. Kaczmarczyk, J. F. Marêché, and G. Furdin, “NaOH activation of anthracites: effect of temperature on pore textures and methane storage ability,” Carbon, vol. 42, no. 14, pp. 2855–2866, 2004.
View at: Publisher Site | Google Scholar
M. M. Maroto-Valer, Y. Zhang, E. J. Granite, Z. Tang, and H. W. Pennline, “Effect of porous structure and surface functionality on the mercury capacity of a fly ash carbon and its activated sample,” Fuel, vol. 84, no. 1, pp. 105–108, 2005.
View at: Publisher Site | Google Scholar
M. Gu, B. Zhang, Z. Qi et al., “Effects of pore structure of granular activated carbons on CH₄ enrichment from CH₄/N₂ by vacuum pressure swing adsorption,” Separation and Purification Technology, vol. 146, pp. 213–218, 2015.
View at: Publisher Site | Google Scholar
S. Wang, L. Lu, D. Wu et al., “Molecular simulation study of the adsorption and diffusion of a mixture of CO₂/CH₄ in activated carbon: effect of textural properties and surface chemistry,” Journal of Chemical & Engineering Data, vol. 61, pp. 4139–4147, 2016.
View at: Publisher Site | Google Scholar
J. Pokrzywinski, J. K. Keum, R. E. Ruther et al., “Unrivaled combination of surface area and pore volume in micelle-templated carbon for supercapacitor energy storage,” Journal of Materials Chemistry A, vol. 5, no. 26, pp. 13511–13525, 2017.
View at: Publisher Site | Google Scholar
K. Munusamy, G. Sethia, D. V. Patil, P. B. Somayajulu Rallapalli, R. S. Somani, and H. C. Bajaj, “Sorption of carbon dioxide, methane, nitrogen and carbon monoxide on MIL-101(Cr): volumetric measurements and dynamic adsorption studies,” Chemical Engineering Journal, vol. 195-196, no. 7, pp. 359–368, 2012.
View at: Publisher Site | Google Scholar
Y. Dang, L. Zhao, X. Lu et al., “Molecular simulation of CO₂/CH₄ adsorption in brown coal: effect of oxygen-, nitrogen-, and sulfur-containing functional groups,” Applied Surface Science, vol. 423, pp. 33–42, 2017.
View at: Publisher Site | Google Scholar
W. Hao, F. Björnerbäck, Y. Trushkina et al., “WITHDRAWN: high-performance magnetic activated carbon from solid waste from lignin conversion processes. Part I: their use as adsorbents for CO₂,” Energy Procedia, vol. 114, no. 12, pp. 6272–6296, 2017.
View at: Publisher Site | Google Scholar
W. Hao, E. Björkman, M. Lilliestråle, and N. Hedin, “Activated carbons prepared from hydrothermally carbonized waste biomass used as adsorbents for CO₂,” Applied Energy, vol. 112, no. 3, pp. 526–532, 2013.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2019 Cai Long Xue et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

2325

Downloads

1336

Citations

Journal of Chemistry

CH4/N2 Adsorptive Separation on Zeolite X/AC Composites

Abstract

1. Introduction

2. Experimental

2.1. Preparation of Zeolite X/AC Composites

2.2. Characterization

2.3. Adsorption Measurements

3. Results and Discussion

3.1. Zeolite X/AC Composites

3.2. CH4 and N2 Adsorption Isotherms

3.3. Effect of Pore Structure and Surface Properties on the Adsorption Performance

3.4. Cycle Adsorption and Time-Dependent Adsorption Capacity of CH4

4. Conclusions

Data Availability

Conflicts of Interest

Acknowledgments

References

Copyright

CH₄/N₂ Adsorptive Separation on Zeolite X/AC Composites

3.2. CH₄ and N₂ Adsorption Isotherms

3.4. Cycle Adsorption and Time-Dependent Adsorption Capacity of CH₄