Table of Contents Author Guidelines Submit a Manuscript
Journal of Engineering
Volume 2013 (2013), Article ID 148362, 11 pages
http://dx.doi.org/10.1155/2013/148362
Research Article

Thermomechanical Impact of Polyurethane Potting on Gun Launched Electronics

US Army RDECOM ARDEC, Picatinny Arsenal Building 94, Morris County, NJ 07806, USA

Received 21 August 2012; Accepted 27 September 2012

Academic Editor: Sadhan C. Jana

Copyright © 2013 A. S. Haynes et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. M. Berman, “Electronic components for high-g hardened packaging,” Tech. Rep. ARL-TR-3705, Army Research Laboratory, 2006. View at Google Scholar
  2. R. E. Keith, “Potting electronic modules,” NASA Technical Report SP-5077, 1969. View at Google Scholar
  3. N.-H. Chao, J. A. Cordes, D. E. Carlucci et al., “The use of potting materials for electronic-packaging survivability in smart munitions,” in Proceedings of the International Mechanical Engineering Conference and Exposition, 2010.
  4. A. R. Jeerfferie, M. Y. Yuhazri, O. Nooririnah et al., “Thermomechanical and morphological interelationship of polypropylene-mulitwalled carbon nanotubes (PP/MWCNTS) nanocomposites,” Internatioanl Journal of Basic and Applied Sciences, vol. 10, no. 4, pp. 29–35, 2010. View at Google Scholar
  5. I. Baylakoglu, C. Hillman, and M. Pecht, “Characterization of some commercial thermally-cured potting materials,” in Proceedings of the International IEEE Conference on the Business of Electronic Product Reliability and Liability, 2003.
  6. N. H. Chao, D. Carlucci, J. A. Cordes, M. E. DeAngelis, and J. Lee, “Implications of a fully-coupled thermal-stresses transient simulation in gun launch applications,” Tech. Rep. ARMET-TR-10030, U.S. Army Armament Research Development and Engineering Center, 2010. View at Google Scholar
  7. A. S. Haynes and J. A. Cordes, “Characterization of a potting material for gun launch,” in Proceedings of the 26th International Symposium on Ballistics, Miami, Fla, USA, September 2011.
  8. ABAQUS Users's Manual V. 6. 10. 1.
  9. J. A. Cordes, P. Vo, J. Lee, and D. Geissler, “Comparison of shock response spectrum for different gun tests,” in Proceedings of the 82nd Shock and Vibration Symposium (SAVIAC '11), Baltimore, Md, USA, October 2011.
  10. D. Carlucci, J. Cordes, S. Morris, and R. Gast, “Muzzle exit (set forward) effects on projectile dynamics,” Tech. Rep. ARAET-TR-06003, U.S. Army Armament Research Development and Engineering Center, Dover, NJ, USA, 2006. View at Google Scholar
  11. N. Blattau, D. Barker, and C. Hillman, “Lead free solder and flex cracking failures in ceramic capacitors,” in Proceedings of the 24th Capacitor and Resistor Technology Symposium, San Antonio, Tex, USA, March 2004.
  12. T. E. Wong, L. Suastegui, H. M. Cohen, and A. H. MAtsunaga, “Experimentally validated thermal fatigue life prediction model for leadleess chip carrier solder joint,” in Proceedings of the 10th Symposium on Mechanics of Surface Mount Assemblies, ASME Winter Annual Meeting, Anaheim, Calif, USA, 1998.
  13. N. Blattau, P. Gormally, V. Iannaccone, L. Harvilchuck, and C. Hillman, “Robustness of surface mount multilayer ceramic capacitors assembled with pb-free solder,” in Proceedings of the CARTS Conference, pp. 25–41, Orlando, FL, April 2006.
  14. G. F. Engel, G. Schlauer, V. Wischnat, and M. Pechloff, “Effective reduction of leakage failure mode after flex cracking events in X7R-type multilayer ceramic capacitors (MLCCS) by using internal series connection,” in Proceedings of theCARTS Europe, Bad Homburg, Germany, September 2006.
  15. J. Prymak, M. Prevallet, P. Blais, and B. Long, “New improvements in flex capabilities for MLC chip capacitors,” in Proceedings of the CARTS Conference, pp. 251–255, Orlando, FL, April 2006.
  16. N. H. Chao, D. Carlucci, J. A. Cordes, M. E. DeAngelis, and J. Lee, “The use of potting materials for electronic-package survivability in smart munitions,” Journal of Electronic Packaging, vol. 133, no. 4, Article ID 041003, 2011. View at Google Scholar
  17. J. A. Cordes, D. E. Carlucci, J. Kalinowski, and L. Reinhardt, “Design and development of reliability gun-fired structures,” Tech. Rep. ARAET-TR-06009, U.S. Army Armament Research Development and Engineering Center, Dover, NJ, USA, 2006. View at Google Scholar
  18. P. Carlucci, J. A. Cordes, N. Payne, L. Reinhardt, and D. Troast, “Dynamic analysis of electronic components for precision munitions, a case study,” Tech. Rep. ARMET-TR-09022, U.S. Army Armament Research, Development and Engineering Center, 2009. View at Google Scholar