Table of Contents Author Guidelines Submit a Manuscript
Journal of Engineering
Volume 2013, Article ID 470241, 10 pages
http://dx.doi.org/10.1155/2013/470241
Research Article

Numerical Investigation of Corrugated Wire Mesh Laminate

1Light Metal Division, Materials Deformation Department, Korea Institute of Materials Science, Changwon 642-831, Republic of Korea
2School of Engineering and Information Technology, University of New South Wales, Australian Defence Force Academy, Canberra, ACT 2600, Australia

Received 4 October 2012; Accepted 11 January 2013

Academic Editor: İlker B. Topçu

Copyright © 2013 Jeongho Choi et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. J. Choi, K. Shankar, A. J. Neely, and A. Fien, “Methods for manufacture of corrugated wire mesh laminates,” in Proceedings of the International Conference on Mechanical Engineering, PWASET, Tokyo, Japan, May 2009.
  2. J. Tian, T. J. Lu, H. P. Hodson, D. T. Queheillalt, and H. N. G. Wadley, “Cross flow heat exchange of textile cellular metal core sandwich panels,” International Journal of Heat and Mass Transfer, vol. 50, no. 13-14, pp. 2521–2536, 2007. View at Publisher · View at Google Scholar · View at Scopus
  3. D. J. Sypeck, “Cellular truss core sandwich structures,” Applied Composite Materials, vol. 12, no. 3-4, pp. 229–246, 2005. View at Publisher · View at Google Scholar · View at Scopus
  4. J. Caulfield, A. M. Karlsson, and D. J. Sypeck, “Crushing of a textile core sandwich panel,” AIAA Journal, vol. 44, no. 6, pp. 1339–1344, 2006. View at Publisher · View at Google Scholar · View at Scopus
  5. I. Özbek, B. A. Konduk, C. Bindal, and A. H. Ucisik, “Characterization of borided AISI 316L stainless steel implant,” Vacuum, vol. 65, no. 3-4, pp. 521–525, 2002. View at Publisher · View at Google Scholar · View at Scopus
  6. D. T. Queheillalt, Y. Katsumura, and H. N. G. Wadley, “Synthesis of stochastic open cell Ni-based foams,” Scripta Materialia, vol. 50, no. 3, pp. 313–317, 2004. View at Publisher · View at Google Scholar · View at Scopus
  7. E. Smethurst, “A new stainless steel alloy for surgical implants compared to 316 S12,” Biomaterials, vol. 2, no. 2, pp. 116–119, 1981. View at Publisher · View at Google Scholar · View at Scopus
  8. D. G. Poitout, Biomechanics and Biomaterials in Orthopedics, Springer, 1st edition, 2004.
  9. G. He and M. Hagiwara, “Ti-Cu-Ni(Fe,Cr,Co)-Sn-Ta(Nb) alloys with potential for biomedical applications,” Materials Transactions, vol. 45, no. 4, pp. 1120–1123, 2004. View at Publisher · View at Google Scholar · View at Scopus
  10. M. Zupan, V. S. Deshpande, and N. A. Fleck, “The out-of-plane compressive behaviour of woven-core sandwich plates,” European Journal of Mechanics, A/Solids, vol. 23, no. 3, pp. 411–421, 2004. View at Publisher · View at Google Scholar · View at Scopus
  11. G. W. Kooistra, V. S. Deshpande, and H. N. G. Wadley, “Compressive behavior of age hardenable tetrahedral lattice truss structures made from aluminium,” Acta Materialia, vol. 52, no. 14, pp. 4229–4237, 2004. View at Publisher · View at Google Scholar · View at Scopus
  12. H. N. G. Wadley, N. A. Fleck, and A. G. Evans, “Fabrication and structural performance of periodic cellular metal sandwich structures,” Composites Science and Technology, vol. 63, no. 16, pp. 2331–2343, 2003. View at Publisher · View at Google Scholar · View at Scopus
  13. ASTM-D-4255/D-4255M-01, Standard Test Method for in-Plane Shear Properties of Polymer Matrix Composite Materials by the Rail Shear Method, ASTM International, 2007.
  14. Laser Extensometers, EIR, (Electronic Instrument Research), Irwin, Pa, USA, 2007.
  15. “Universityof Alberta. ANSYS Tutorials,” 2001, http://www.mece.ualberta.ca/tutorials/ansys/IT/Buckling/Buckling.html.