Effects of Microwave Power on Extraction Kinetic of Anthocyanin from Blueberry Powder considering Absorption of Microwave Energy

Xue, Hongkun; Xu, Hao; Wang, Xiaorui; Shen, Liuyang; Liu, Han; Liu, Chai; Qin, Qingyu; Zheng, Xianzhe; Li, Qingyan

doi:https://doi.org/10.1155/2018/9680184

Journal of Food Quality

On this page

Abstract Introduction Materials and Methods Results and Discussion Conclusions Conflicts of Interest Acknowledgments References Copyright Related Articles

Research Article | Open Access

Volume 2018 | Article ID 9680184 | https://doi.org/10.1155/2018/9680184

Effects of Microwave Power on Extraction Kinetic of Anthocyanin from Blueberry Powder considering Absorption of Microwave Energy

Hongkun Xue,¹Hao Xu,¹Xiaorui Wang,¹Liuyang Shen,¹Han Liu,¹Chai Liu,¹Qingyu Qin,¹Xianzhe Zheng,¹and Qingyan Li¹

Academic Editor: Hong-Wei Xiao

Received05 Nov 2017

Accepted14 Jan 2018

Published28 Feb 2018

Abstract

Microwave power as directly controlled parameter determines the absorption of microwave energy inside extraction vial and the yield of objective component in microwave-assisted extraction (MAE). The aim of this study was to elucidate the effects of microwave powers on the yield of anthocyanin from blueberry (Vaccinium spp.) powder based on the absorption of microwave energy in extracts under MAE. Rising microwave powers have little effect on the distribution of microwave energy in extraction vial, but increase its temperature. The simulation results indicated that strength of electrical field tends to decay trend along with microwave irradiation; however, temperatures have the highest level in center location in an extraction vial. High microwave power strongly breaks cell wall of blueberry to open diffusion route of interior anthocyanin toward extraction solvent. A critical extraction temperature of °C is obtained with the highest anthocyanin yield under MAE. Three monomers of anthocyanin including pelargonidin, cyanidin, and delphinidin are, respectively, of the highest content of 1.02 μg/mL, 0.66 μg/mL, and 0.31 μg/mL. The research results contribute to the improvement of efficiency of microwave energy and yield of anthocyanin.

1. Introduction

Blueberry (Vaccinium spp.) fruit contains abundant anthocyanin [1], which has great medical and nutritional value in antioxidation, antiaging, and protecting cardiovascular and cerebrovascular diseases [2]. Microwave-assisted extraction (MAE) is a promising extraction method to extract compounds from plant-based materials, for example, flavonoids [3], pectin [4], phenolic compounds [5], and oil [6]. MAE is suitable for the extraction of anthocyanin from blueberry fruits [7]. Already, studies about microwave extraction of bioactive components mostly focus on the extraction properties, parameter optimization, and the yield of objective components. Zheng et al. [8] found that the solid-to-liquid ratio has the most important effect on the anthocyanin extraction kinetic from blueberry powder, followed by the ethanol concentration and extraction temperature, and the extraction time of anthocyanin from blueberry powder in MAE has the least effect. The coupling transfer of mass and heat at the same direction speeds up the extraction process at higher extraction yield [9]. The absorption of microwave energy of material tends to variable trend inside material along microwave incident direction [10], which determines the distribution and change of temperature in extraction vial. The nonuniform distribution of microwave energy results from the changes of dielectric properties and the decay of electric field strength in extraction solution. In MAE, microwave irradiation into extraction vial forms complex interaction of absorption of microwave energy. Existing studies considered the microwave power as the uniform distribution in extraction vial, however, producing localized hot and cold points to cause the nonuniform distribution of heating and degradation of components extracted. Microwave power dominates the absorption and conversion behaviors of microwave energy inside extraction vial, which obviously depended on its dielectric properties [11]. Some researches were done to reveal the relevance of microwave power and the absorption of microwave energy in extraction vial. Han et al. [12] and Chan et al. [13] defined microwave absorption coefficient to characterize effects of the dielectric properties on the absorption amount of microwave energy in extraction vial. Chan et al. [14] explained the absorption of the microwave energy in nature considering the changes of dielectric properties of the extraction vial in MAE process. Therefore, the investigation of microwave power contributes to improving the utilization of microwave energy and the yield of anthocyanin. The model of absorption of the microwave energy as the function of microwave power may be built based on the changes of dielectric properties as the function of temperature in the extraction vial.

In microwave heating, electromagnetic field causes the rapid rotation of polar molecules and rapid movement of ionic in polar material to form the violent frication [15]. Absorption of microwave energy in extraction vial generates the volumetric heating to determine the temperature distribution, which influences the extraction and degradation of components extracted in MAE [16]. Microwave volumetric heating instantaneously raises the temperature to accelerate the pressure build-up inside cell of plant-based materials. This pressure causes the rupture of the cell wall to release the component into the extraction solution to accelerate the diffusion of component out of the source material [17]. Computer simulation is an effective method to analyze the process of extraction and degradation of components extracted in MAE. Navarrete et al. [18] simulated the changes of yield and evaporation of essential oils from Lavandin super under different temperatures in MAE. Chan et al. [14] studied the diffusion of antioxidant compounds from cocoa leaves considering absorbed microwave energy in MAE. In addition, regression models from response surface methodology and artificial neural network are applied to optimize the process parameters in MAE [19].

The absorption of microwave energy inside extraction vial was evenly considered as the uniform distribution. However, both the microwave propagation at conversion between electric field and magnetic field and the dissipation of microwave energy at exponential attenuation in extraction vial result in nonuniform distribution of microwave energy, which give rise to the “hot” and “cold” point of temperature in vial. This nonuniform distribution of microwave energy causes the uncertainty of effect of microwave power on the extraction process of objective components. To explore the distribution of microwave energy and temperature inside extraction vial may conduce to explaining the microwave extraction process.

To the authors’ best effort, however, little information was published about the effects of microwave powers on the absorption of microwave energy inside extraction vial and yield of anthocyanin from blueberry powder in MAE. Based on the above-mentioned studies, to elucidate microwave power on the extraction of anthocyanin from blueberry powder, the objectives of this study are as follows:

(1) To elucidate the distribution of temperature in extraction vial under different microwave powers

(2) To analyze the effects of microwave power on the yield and degradation rate of anthocyanin from blueberry powder.

2. Mathematical Model Development

In working microwave equipment, there exists complex interaction between the microwave irradiation and material processed. The electric field strength of prorogation of microwave in cavity obeys Maxwell’s law aswhere is wave number of free space, is electric field strength, V/m, is permeability of dielectric constant, is relative dielectric constant, is angular velocity, rad/s, is vacuum dielectric constant, is thermal conductivity, W/m·K, is imaginary unit, and is electric conductivity, S/m.

According to the law of energy conservation, the absorption of microwave energy in the extraction vial is consumed by the thermal accumulation and thermal diffusion as shown inwhere is material density, kg/m³, is specific heat capacity, J/kg·K, k is coefficient of thermal diffusion, W/m·K, is extraction temperature, °C, is heat source, W/m³, is extraction time, s, and is current velocity, m/s. Convection was ignored in the energy and species balance equations. Mass diffusion was not considered in the species balance equation.

In microwave field, the intensity frication of polar molecule in dielectric material generates the volumetric heating, which depends on the electric loss factor of material and electric field strength as shown inwhere is dielectric loss factor, is microwave frequency of 2450 MHz, is vacuum dielectric constant, and is electric field intensity, V/m.

For (2), initial conditions were set at and , where is initial concentration and is room temperature, 20°C. Initial temperature and anthocyanin content were uniform in the extraction vial. Boundary conditions were set as no mass transfer and heat convection at the interface between solvent and glass as (4) and (5), respectively.where is the ambient temperature, 25°C, and is the coefficient of convective heat transfer, 40 W/m²·K.

From (3), the absorption amount of microwave energy depends on the dielectric properties and electrical field strength in extraction vial. The dielectric properties of extraction liquid as the function of temperature are shown as follows [20]:

To estimate the degradation kinetic of anthocyanin monomers, the changes of delphinidin, cyanidin, and pelargonidin follow Lorenz’s function, inwhere is content of anthocyanin monomer including delphinidin cyanidin and pelargonidin, μg/mL, is microwave power when reaches maximum value, is initial anthocyanin monomer content, μg/mL, is constant, and is constant of extraction yield.

3. Materials and Methods

3.1. Preparations of Blueberry Powder

Fresh wild blueberries were collected from the Xiangfang farm of Harbin in China. Blueberries were selected, cleaned, and then placed into a cool storage room of refrigerator at 4°C. The cooling stored blueberries were taken out from refrigerator and smashed by using fruit pulping machine (Philips-30, Zhuhai, China) to acquire the blueberries purees. Then, the blueberries purees were frozen in a TD-50 freezing-vacuum dryer (Shanghai Pudong Freeze Drying Equipment Co., Ltd., Shanghai, China) at temperature of −18°C. Freeze-vacuum drying operation was continuously run until the moisture content of the blueberry slices was below 0.5% (w.b.) in about 24 h. The blueberry powders were prepared by using a plant grinder with a screen through 40 meshes. The dehydration blueberry powders were packed in a sealed dark plastic bag and stored in the refrigerator in −20°C for the further experiments. The standard substances of delphinidin chloride, cyanidin chloride, and pelargonidin chloride were provided by Sigma Corporation.

According to research objectives mentioned above, the research route was developed as shown in Figure 1 to investigate the effects of microwave powers on extraction and degradation of anthocyanin from blueberry powder considering absorption of microwave energy. A step-by-step research mode to be constructed as simulation-analysis-elucidation in Figure 1 reveals the mechanism of microwave powers on extraction kinetic of anthocyanin from blueberry powder.

3.2. Experimental Methods

In MAE, ethanol solvent was selected as the extraction solvent due to its high dielectric properties to absorb much more microwave energy and high solubility for the anthocyanin. According to the preliminary experimental results [8], lyophilized blueberry powder of g was weighted to put into extraction vessel at ethanol concentration of 60% and ratio of solid to liquid of 1 : 30 (g/mL). The mixture of ethanol and blueberry powder was placed in the extraction vessel. Then the extraction vessel was placed in the center of the microwave workstation (MWS, FISO Technologies Inc., Quebec, Canada) and connected with the temperature sensor. In MAE, the microwave input power was set from 100 W to 400 W with 100 W intervals, and the total extraction time was 80 s at sampling interval of 10 s. Extraction vial refers to the blueberry powder dissolved in extraction liquid in MAE.

Microwave intensity is introduced to clarify the relationship between the microwave power and sample mass, which is defined as the ratio of microwave power to sample mass, W/g. Microwave intensities were set to 50~250 W/g with the interval of 50 W/g. To compare the effects of different microwave intensities on the content of anthocyanin in blueberry, the extraction conditions were set as extraction time of 80 s and weight of blueberry powder of g. According to optimal conditions at preliminary experiment, the ethanol concentration and the ratio of solid to liquid were selected as 60% and 1 : 30, respectively. The extracts were taken for the further measurements.

3.2.1. Temperature Measurement

An optical fiber sensor of temperature (FOT-L-SD-C1-F1-M2-R1-ST, FISO Co., Quebec, Canada) was used to measure temperature of extraction vial in MAE.

A glass vessel loading extraction vial was placed in a microwave workstation (MWS, FISO Technologies Inc., Quebec, Canada). The connection tips of optical fiber sensors were interconnected with the ports of a signal decoder fixed on the top of the microwave station. Then the tip of optical fiber sensor of temperature was plugged into extraction liquid to collect temperature at 0.03 s acquirement interval. The temperature of extraction in MAE was recorded using a computer.

3.2.2. Determination of Anthocyanin Extraction Yield and Degradation Rate

An UV/Vis spectrometer (Lambda 35, Perkin Elmer, Singapore) with a variable wavelength detector was employed to measure the anthocyanin content. The highest absorbance of blueberry extract was achieved at 500 nm wavelength according to the results from preliminary experiments. The plotting curve was obtained by fitting the absorption and the anthocyanin concentration. Thus, a standard curvilinear equation was fitted as shown in

The anthocyanin concentration was calculated by using (8); then the anthocyanin yield can be calculated by taking the calculated anthocyanin concentration intowhere is anthocyanin yield, %, is concentration of anthocyanin, mg/mL, is the constant volume, mL, is the multiple factor of dilution, and is the total content of anthocyanin in 1 g raw material, mg/g.

Anthocyanin residue rate was calculated by determining the absorbance of the residue solution. Anthocyanin degradation rate was calculated by usingwhere is anthocyanin yield, %, is anthocyanin degradation rate, %, and is anthocyanin residue rate, %.

3.2.3. HPLC-MS Analysis Method

Liquid chromatograph mass spectrometer (HPLC-MS) consisted of an HPLC (Agilent 1200) coupled to a diode array detector and mass spectrometer (MSD, SL mode, Agilent, Palo Alto, CA). A reversed-phase C₁₈ column (250 mm × 94.6 mm, 5 μm, Kromasil), preceded by a guard column (4 mm × 3.0 mm, Kromasil) of the same stationary phase, was used at a flow rate of 1.0 mL/min. A binary solvent system was employed: 5% methane acid was used as solvent A and a mixture of 96% ethanol and 5% methane acid was used as solvent B. The diode array UV detector (DAD) was set at 520 nm to record the peak intensity. The gradient elution was carried out as the following procedure: in 0~30 min, flowing mobile phase A from 90% to 10%; in 30~32 min, elution operation using 10% mobile phase A; in 33~38 min, elution operation using 90% mobile phase A. Flow rate was set at 1.0 mL/min at room temperature with injection volume of 20 μL for samples. A split joint was connected with detector at a flow of 0.3 mL/min to the mass spectrometer.

The mass spectrometer was operated in both positive and negative ion modes. The capillary voltage was set to 4.0 kV, the cone voltage to 22.0 V, and the extractor voltage to 3.0 V. HPLC-ESI-MS system was operated by using Bruker Daltonics software. The mass scan scope is from to . Mixed solution of three chemical compounds standards mentioned (each compound with 0.1 mg/mL dissolved in 60% ethanol) in part of the sample preparation and 60% methanol extract were tested, respectively, by using HPLC-MS under the above condition.

3.2.4. Quantitative Analysis of Monomer Compounds of Anthocyanin

HPLC-DAD consisting of a Prominence LC-2030C was used to measure monomer compounds of anthocyanin extracted from blueberry powder. A reversed-phase C₁₈ column (250.0 mm × 94.6 mm, 5.0 μm, Kromasil), preceded by a guard column (4.0 mm × 3.0 mm, Kromasil) of the same stationary phase, was operated at a flow rate of 1.0 mL/min. The determination of anthocyanin (delphinidin, cyanidin, and pelargonidin) was performed at 520 nm. Standard samples were injected for identification and quantitative analysis. Three species of standard solution including delphinidin, cyanidin, and pelargonidin were prepared in six different concentrations. HPLC spectra of three anthocyanin standards were presented by using peak area. The regression equations were fitted to describe the relationships between the content of anthocyanin monomer and the peak area of HPLC spectra as follows:where , , are, respectively, the content of the anthocyanin standard of delphinidin, cyanidin, and pelargonidin and , , are, respectively, the corresponding standard sample of peak area of the HPLC spectra.

3.3. Observation of the Microstructure of Blueberry Powder Cell

To observe the cell wall broken by microwave power, a scanning electron microscopy (SEM) (Hitachi High Technologies Inc., IL, USA) was employed to observe the microstructure of kernel of blueberry powder. The lyophilized blueberry powders of 2.0000 ± 0.0005 g from step 3.1 were dissolved with 60 mL of 60% ethanol. The mixtures were incubated at room temperature for 80 s; then they were centrifuged at 4000 rpm for 15 min in a microliter centrifuge (International Equipment, MA, USA). The supernatant was collected for the determination of anthocyanin yield. The residual residue was washed with 60% ethanol until the residue was colorless, and the residue from washing liquid was collected to calculate anthocyanin residue rate. The residue sample was fixed on a holder using an aluminum tape and sputtered with a thin layer of gold, and then the sample was placed into vacuum cavity with an acceleration voltage of 12.5 kV, followed by observation operation. Blueberry powder samples by MAE were prepared as follows. Lyophilized blueberry powders of 2.0000 ± 0.0005 g were dissolved with 60 mL of 60% ethanol. The mixtures were placed into a microwave station at microwave power of 100 W, 200 W, 300 W, and 400 W, respectively, for 80 s. The rest of the operation is the same as the raw sample. The residues of blueberry powder were used as blueberry powder samples by MAE, which were used to observe the operation.

3.4. Statistical Analysis

All experiments were conducted in triplicate. The experimental data were presented as mean values with standard deviations. Differences between mean values were established using Duncan’s new multiple range tests at a confidence level of 95%. All statistical calculations were performed using SAS software (8.0, SAS Institute Inc., NC, USA). SigmaPlot software (12.5, Systat Software Inc., USA) was used to fit regression equations according to highest correlation coefficient () and the lowest standard mean deviation (SMD) value. COMSOL Multiphysics (V5.3a COMSOL Multiphysics, Burlington, MA, USA) software was employed to simulate the absorption of microwave energy in extracts’ electric field, temperature, and yield of anthocyanin in extraction vial under different microwave powers. Schematic diagram of microwave workstation and extraction vial placement and the model structure of vial in simulation of COMSOL software were shown in Figures 2 and 3, respectively. The cylindrical vial was of 100 mm height and 20 mm diameter and was marked with five positions at equal distance of 20 mm.

(a)

(b)

4. Results and Discussion

4.1. Absorption of Microwave Energy inside Extraction Vial under Different Microwave Powers

Microwave powers have obviously positive effects on the absorption of microwave energy inside extraction vial. In MAE, the dielectric constant and dielectric loss factor of extraction vial increased with the microwave power. Higher power caused much more extraction yield of anthocyanin with its degradation into charged ions and polar molecules [7]. There are different side groups on the flavylium ion in anthocyanin, which can be a hydrogen atom, a hydroxide, or a methoxy-group [21]. The static dielectric constant increases with the decrease of molecular weights, mainly as a result of increased polarity with the small molecules [10]. Therefore, anthocyanin contains a large number of polar hydroxyl molecules dissolved into extracts to raise the dielectric constant and dielectric loss factor of the extraction vial. In addition, high temperature causes the degradation of anthocyanin to form a chalcone structure to increase the amount of charged ions and polar molecules in extraction vial [22], in which smaller molecules have higher mobility and less relaxation time than those of larger molecules in MAE [23].

The absorption of microwave energy characterizes the utilization of microwave input power, which depends on the changes of dielectric properties of material and electrical field strength. The distributions of microwave energy inside extraction vial under different microwave powers are presented in Figures 4(a)–4(d). The electric strength under different microwave powers had the same distribution trends with high and low area, but increased with the increase of microwave power. These results were attributed to the unchanged distance and position between the extraction vial and port of waveguide of microwave magnetron.

(a) 100 W

(b) 200 W

(c) 300 W

(d) 400 W

As shown in Figure 4, absorption of microwave energy had obvious nonuniform distribution inside extraction vial at extraction time of 80 s. The absorption amount was at the highest level at the position close to the output of waveguide of magnetron in the microwave workstation. Microwave energy tended to decay trends along the radial of extraction vial from the microwave irradiation direction. The absorption of microwave energy in extraction vial as the function of microwave power is shown as follows [24]:where is rated power of microwave applicator, W, is cross-sectional area of wave guide, 0.6235 m², is light speed of 3 10⁸ m/s, is the radium of extraction vessel, mm, is position from vessel center along the radium, mm, is penetration depth of microwave energy along microwave propagation, mm, and is attenuation factor as follows:

In MAE, microwave penetration tended to exponential decay trend along microwave irradiation direction from surface of vessel to center. However, the absorption of microwave energy showed a rising trend from the surface to the center of extraction vessel. The result was attributed to the electrical field distribution under different microwave power. The electrical field had high strength at center location and declined toward surface of extraction vessel in MAE. The changes of dielectric properties inside extraction vial influence substantially electric field strength. The wavelength and penetration may present microwave transmit within the material along its incident direction as shown in [25]where is wavelength, mm, is penetration depth, mm, is attenuation factor, and is phase transfer factor as follows:

The higher microwave power caused the larger dielectric properties of extraction vial in MAE. The attenuation factor and phase transfer factor increased with the elevation of dielectric constant and dielectric loss factor to decline wavelength and penetration depth . For the curved surface of cylinder shape of extraction vessel, transmitted microwaves converge toward center location inside the extraction vial due to large radium under a smaller wavelength and larger penetration depth [26]. This resulted in strong focusing occurrence of electric field strength in extraction vial as shown in Figure 4. The distribution and changes of absorption of microwave energy depend on uneven strength of electric field and rising dielectric properties inside extraction vial. Microwave irradiation has focused effect along the direction of propagation to achieve the strongest strength of electric field at the center [10].

4.2. Effects of Microwave Power on the Profiles of Temperature in the Extraction Vial

The profiles of temperature depend on absorption of microwave energy and the microwave power inside extraction vial. As shown in Figure 5, the temperature of the extraction vial increased with microwave power. The absorption of microwave energy was consumed in thermal accumulation and diffusion inside extraction vial to increase its temperature [27].

(a) 100 W

(b) 200 W

(c) 300 W

(d) 400 W

As shown in Figure 5, the temperature distribution presented uneven distribution with increasing trends along the radial of the extraction vial. The temperature was the highest at the center of the extraction vital and the top temperature of vial was the lowest under different microwave powers. This was attributed to the highest value of the electric field and the absorption of microwave energy at center location of the extraction vital. Due to the exponential decay of microwave absorption inside extraction vial [28], the distance of propagation had negative effects on the microwave energy flux toward center of vessel along radius. The greater distance of propagation caused less microwave energy absorption, which resulted in the lowest temperature of the extraction vessel bottom [29]. The rotation of glass disc loading extraction vial resulted in the uniformity of heating chance, which smoothes the temperature difference caused by the uneven absorption of microwave energy inside the extraction vial. As shown in Figure 5, the rate of rising temperature in extraction vial was 0.25, 0.31, and 0.1°C/s with the 100 W increment of microwave power in 100~400 W at extraction time of 80 s. Low rising rate of temperature from 76°C to 84°C in 80 s at 0.1°C/s was due to boiling state of temperature of extraction vial at 84°C. The higher microwave power caused the rapider rate of rising temperature. The results provided a theoretical basis for selection of microwave power to improve the efficiency of microwave energy and reduce the degradation of anthocyanin due to local high temperature.

Coefficient of uniform of temperature distribution is as shown inwhere COU is coefficient of uniform of temperature distribution, AV is average temperature, and SE is the standard error of temperature. COU indicates the discrete degree of temperature data. Higher COU presents more uniform distribution of temperature. As shown in Figure 6, the distribution of temperature had higher COU near the bottom of −34 mm and top location of 26 mm at extraction vial than that of middle location of extraction. The center of outport of microwave guidance is as high as 40 mm, in which microwave power directly irradiated the location other than convection to generate high temperature with uniform distribution. The measurements of temperature at top, middle, and bottom location of extraction vial shown in Figure 7 were consistent with the simulation in Figure 5 (400 W).

4.3. The Effects of Microwave Power on the Anthocyanin Yield and Degradation Rate

Microwave power is the most important factor in the microwave extraction process, which determines anthocyanin yield and degradation rate. The results are shown in Figure 8.

(a)

(b)

As shown in Figure 8(a), the anthocyanin yield increased from 63.54% ± 0.57% to 72.33% ± 0.89% and 64.17% ± 0.87% to 74.52% ± 0.55% in microwave powers of 100 W and 200 W, respectively. This phenomenon was attributed to the increase in the temperature of the extract. Rising temperatures contributed to building up intracellular pressure to rupture cell walls and reduce the diffusion resistance of anthocyanin. On the other hand, the increase of temperature resulted in the increase of the solubility of anthocyanin and the decrease of the extracts viscosity [13]. Therefore, anthocyanin in the blueberry cells was more easily diffused from the cells into solvents, which increased anthocyanin yield. The anthocyanin yield tended to obviously increasing trends till 76.58% ± 0.38% in 50 s at the temperature of 50.75 ± 0.88°C () and then dropped dramatically in the microwave power of 300 W (). The anthocyanin yield initially increased to reach the highest value of 77.51% ± 0.55% in 30 s at the temperature of 50.75 ± 0.88°C and then significantly decreased till the extraction end in the microwave power of 400 W (). Based on these results, we deduced that the critical temperature of anthocyanin extraction () was °C. The critical temperature indicates that the acquirement of anthocyanins dominates the extraction process in temperatures lower than and the degradation of anthocyanin dominates the process in temperatures higher than . This result is similar to the results of Chumnanpaisont et al. [30] and Sun et al. [7]. As shown in Figure 8(b), the anthocyanin degradation rate significantly increased with the extraction time under different microwave powers (). This was because the thermal accumulation caused the local high temperature in the later stage in MAE, which destroyed the anthocyanin structure to increase rate of anthocyanin degradation [31].

4.4. Effects of Microwave Power on the Microstructure of Cell of Blueberry Powders in MAE

Blueberry cell wall is composed of cellulose, hemicellulose, and pectin. Anthocyanin exists in blueberry cells, and the cell wall is a barrier for the diffusion of anthocyanin from the cell. The permeability of cell wall of blueberry powder plays a key role in smooth anthocyanin extraction. The structural changes of blueberry cells of raw and extracted sample were observed by using a SME to understand the extraction effect of the MAE of anthocyanin from blueberry powder. The SME results are shown in Figures 9(a)–9(e). Figure 9(a) showed that the intact blueberry cells were present on the surface of tissues of raw blueberry granules. The microstructure of blueberry granule underwent MAE as shown in Figures 9(b), 9(c), 9(d), and 9(e) at microwave input power of 100 W, 200 W, 300 W, and 400 W, respectively, which presented intense damage within blueberry powder. The higher microwave power caused more obvious rupture of cell wall of blueberry powder. The absorption of microwave energy within extraction vial had positive correlation with the microwave power. High absorption of microwave energy caused rapid temperature increase of extraction vial, which resulted in internal pressure build-up and accumulation in blueberry cells [32]. When the internal pressure inside cell of blueberry powder exceeded the yield of cell wall, cell wall was ruptured to release anthocyanin into solvents. Blueberry cell structure might also be thermally damaged due to the thermal degradation of pectin in cellular middle lamella [33]. This result weakened the adhesion between cells and integrity of the cell membrane [34]. This destruction improved the permeability of cell wall to release the anthocyanin existing in cell toward solution, which obviously increased the yield of anthocyanin [35].

(a) Raw sample

(b) 100 W

(c) 200 W

(d) 300 W

(e) 400 W

4.5. Extraction Kinetic of Anthocyanin under Different Microwave Powers

In MAE, the absorption of microwave energy in extraction vial caused rapid increase of its temperature. However, excessively high extraction temperature may cause the degradation of extracted components [7]. According to the yield of three species of anthocyanin monomers of the experimental data in MAE shown in Figure 10, regression coefficients of (7) were fitted as shown in Table 1. The highest yield of pelargonidin, cyaniding, and delphinidin was, respectively, 1.02, 0.54, and 0.30 μg/mL at microwave intensity of 109, 108, and 120 W/g. It was observed that blueberry powder settled at the bottom of the vial along axis of −40~−60 mm shown in Figure 6 in MAE. The distribution of temperature tended to center high and edge low trends. The temperature domain of blueberry powder dissolved in vial was, respectively, in range of 40~45°C, 53~58°C, 61~70°C, and 71~78°C at microwave powers of 100 W, 200 W, 300 W, and 400 W. The improvement of high microwave power on the yield of anthocyanin was attributed to the cell wall broken to release the anthocyanin existing in cell toward solution and the decrease of solvent viscosity to effectively speed up the diffusivity of solvent and solute within extraction vial, which increased the solubility of anthocyanin in solution [36]. But high microwave power induced anthocyanin degradation in the later stage of extraction due to local high temperature [37].

(a)

(b)

(c)

Anthocyanin of blueberry contains three monomers including delphinidin, cyanidin, and pelargonidin which were detected by using LC-MS. As shown in Figure 10, the changes of the extraction and degradation of the three anthocyanin monomers were obtained under different microwave intensities. The results from Figure 10 indicated that pelargonidin content was the highest, followed by cyaniding content, and delphinidin content was the lowest. Under the microwave power of 50 W/g, the temperature of extraction vial achieved 40~45°C. The extraction temperature is too low to produce sufficient energy to extract the anthocyanin from blueberry powder. When the microwave power was at 100 W/g, the temperature of the extracts was 53~58°C and the content of each component reached the maximum value. This temperature was close to the critical temperature of anthocyanin extraction of 50.75 ± 0.88°C. When the microwave power was higher than 100 W/g, the temperature of the extracts was greater than 61~70°C, which induced the degradation of anthocyanin [38].

5. Conclusions

There exists obviously nonuniform distribution of absorption of microwave power and temperature in extraction vial. The uniform temperature distribution is higher near bottom and top location than that of middle location of extraction vial; however, microwave power presents nonsignificant effect on uniform temperature distribution. Microstructure of cell wall of blueberry powders indicates that high microwave power intensively ruptures the cell wall of blueberry to weaken obvious diffusion resistance of interior anthocyanin toward extraction solvent. Pelargonidin content was the highest, followed by cyaniding content, and delphinidin content was the lowest for the anthocyanin extracted from blueberry powders in MAE. The research results suggested that the controlling microwave power contributes to the improvement of anthocyanin yield and efficiency of microwave energy.

Conflicts of Interest

The authors declare that they have no conflicts of interest.

Acknowledgments

The authors gratefully acknowledge the financial support provided by the National Natural Science Foundation of China (31571848) for this research project.

References

M. Zielinska and A. Michalska, “Microwave-assisted drying of blueberry (Vaccinium corymbosum L.) fruits: drying kinetics, polyphenols, anthocyanins, antioxidant capacity, colour and texture,” Food Chemistry, vol. 212, pp. 671–680, 2016.
View at: Publisher Site | Google Scholar
I. E. Garofulić, V. Dragović-Uzelac, A. R. Jambrak, and M. Jukić, “The effect of microwave assisted extraction on the isolation of anthocyanins and phenolic acids from sour cherry Marasca (Prunus cerasus var. Marasca),” Journal of Food Engineering, vol. 117, no. 4, pp. 437–442, 2013.
View at: Publisher Site | Google Scholar
R. Y. Krishnan and K. S. Rajan, “Microwave assisted extraction of flavonoids from Terminalia bellerica: study of kinetics and thermodynamics,” Separation and Purification Technology, vol. 157, pp. 169–178, 2016.
View at: Publisher Site | Google Scholar
S. S. Hosseini, F. Khodaiyan, and M. S. Yarmand, “Optimization of microwave assisted extraction of pectin from sour orange peel and its physicochemical properties,” Carbohydrate Polymers, vol. 140, pp. 59–65, 2016.
View at: Publisher Site | Google Scholar
E. Durmaz, G. Sumnu, and S. Sahin, “Microwave-assisted extraction of phenolic compounds from caper,” Separation Science and Technology, vol. 50, no. 13, pp. 1986–1992, 2015.
View at: Publisher Site | Google Scholar
M. Taghvaei, S. M. Jafari, S. Nowrouzieh, and O. Alishah, “The influence of cooking process on the microwave-assisted extraction of cottonseed oil,” Journal of Food Science and Technology, vol. 52, no. 2, pp. 1138–1144, 2013.
View at: Publisher Site | Google Scholar
Y. Sun, H. K. Xue, C. H. Liu, C. Liu, X. L. Su, and X. Z. Zheng, “Comparison of microwave assisted extraction with hot reflux extraction in acquirement and degradation of anthocyanin from powdered blueberry,” International Journal of Agricultural and Biological Engineering, vol. 9, no. 6, pp. 186–199, 2016.
View at: Publisher Site | Google Scholar
X. Zheng, X. Xu, C. Liu, Y. Sun, Z. Lin, and H. Liu, “Extraction characteristics and optimal parameters of anthocyanin from blueberry powder under microwave-assisted extraction conditions,” Separation and Purification Technology, vol. 104, no. 5, pp. 17–25, 2013.
View at: Publisher Site | Google Scholar
M. Golmakani and M. Moayyedi, “Comparison of heat and mass transfer of different microwave-assisted extraction methods of essential oil from,” Food Science & Nutrition, vol. 3, no. 6, pp. 506–518, 2015.
View at: Publisher Site | Google Scholar
C. Liu, C. Liu, H. Xue et al., “Effect of microwave energy dissipation on drying process of berry puree under microwave foam drying conditions,” Drying Technology, vol. 35, no. 11, pp. 1388–1397, 2017.
View at: Publisher Site | Google Scholar
T. Santos, M. A. Valente, J. Monteiro, J. Sousa, and L. C. Costa, “Electromagnetic and thermal history during microwave heating,” Applied Thermal Engineering, vol. 31, no. 16, pp. 3255–3261, 2011.
View at: Publisher Site | Google Scholar
G. Z. Han, M. D. Chen, P. S. Guo, and S. X. Li, “Absorption coefficient and absorption density of microwave energy of microwave in microwave assisted extraction,” Journal of South China University of Technology, vol. 35, pp. 52–57, 2007.
View at: Google Scholar
C.-H. Chan, J.-J. Lim, R. Yusoff, and G.-C. Ngoh, “A generalized energy-based kinetic model for microwave-assisted extraction of bioactive compounds from plants,” Separation and Purification Technology, vol. 143, pp. 152–160, 2015.
View at: Publisher Site | Google Scholar
C.-H. Chan, R. Yusoff, and G.-C. Ngoh, “Modeling and prediction of extraction profile for microwave-assisted extraction based on absorbed microwave energy,” Food Chemistry, vol. 140, no. 1-2, pp. 147–153, 2013.
View at: Publisher Site | Google Scholar
K. Pitchai, S. L. Birla, J. Subbiah, D. Jones, and H. Thippareddi, “Coupled electromagnetic and heat transfer model for microwave heating in domestic ovens,” Journal of Food Engineering, vol. 112, no. 1-2, pp. 100–111, 2012.
View at: Publisher Site | Google Scholar
J. I. Lombraña, R. Rodríguez, and U. Ruiz, “Microwave-drying of sliced mushroom. Analysis of temperature control and pressure,” Innovative Food Science and Emerging Technologies, vol. 11, no. 4, pp. 652–660, 2010.
View at: Publisher Site | Google Scholar
A. Patil and A. K. Singh, “Effect of enzyme and microwave pretreatment on oil recovery from canola,” Journal of Food Process Engineering, vol. 40, no. 1, Article ID e12340, 2016.
View at: Publisher Site | Google Scholar
A. Navarrete, R. B. Mato, and M. J. Cocero, “A predictive approach in modeling and simulation of heat and mass transfer during microwave heating. Application to SFME of essential oil of Lavandin Super,” Chemical Engineering Science, vol. 68, no. 1, pp. 192–201, 2012.
View at: Publisher Site | Google Scholar
K. Sinha, P. D. Saha, and S. Datta, “Response surface optimization and artificial neural network modeling of microwave assisted natural dye extraction from pomegranate rind,” Industrial Crops and Products, vol. 37, no. 1, pp. 408–414, 2012.
View at: Publisher Site | Google Scholar
L. Zhen, Dielectric properties of berry fruit under microwave processing [Ph.D. thesis], Northeast Agricultural University, Harbin, China, 2013.
A. Martynenko and Y. Chen, “Degradation kinetics of total anthocyanins and formation of polymeric color in blueberry hydrothermodynamic (HTD) processing,” Journal of Food Engineering, vol. 171, pp. 44–51, 2016.
View at: Publisher Site | Google Scholar
A. Patras, N. P. Brunton, C. O'Donnell, and B. K. Tiwari, “Effect of thermal processing on anthocyanin stability in foods; mechanisms and kinetics of degradation,” Trends in Food Science & Technology, vol. 21, no. 1, pp. 3–11, 2010.
View at: Publisher Site | Google Scholar
The Microwave Processing of Foods, Woodhead Publishing, Duxford, UK, 2nd edition, 2017.
X. Zheng, Y. Wang, C. Liu et al., “Microwave energy absorption behavior of foamed berry puree under microwave drying conditions,” Drying Technology, vol. 31, no. 7, pp. 785–794, 2013.
View at: Publisher Site | Google Scholar
H. Zhang and A. K. Datta, “Heating concentrations of microwaves in spherical and cylindrical foods,” Food and Bioproducts Processing, vol. 83, no. 1, pp. 14–24, 2005.
View at: Publisher Site | Google Scholar
H. Zhang and A. K. Datta, “Heating concentrations of microwaves in spherical and cylindrical foods,” Food and Bioproducts Processing, vol. 83, no. 1, pp. 6–13, 2005.
View at: Google Scholar
W. Sookjitsumran, S. Devahastin, A. S. Mujumdar, and N. Chiewchan, “Comparative evaluation of microwave-assisted extraction and preheated solvent extraction of bioactive compounds from a plant material: a case study with cabbages,” International Journal of Food Science & Technology, vol. 51, no. 11, pp. 2440–2449, 2016.
View at: Publisher Site | Google Scholar
C.-H. Chan, H. K. Yeoh, R. Yusoff, and G. C. Ngoh, “A first-principles model for plant cell rupture in microwave-assisted extraction of bioactive compounds,” Journal of Food Engineering, vol. 188, pp. 98–107, 2016.
View at: Publisher Site | Google Scholar
D. M. Patil and K. G. Akamanchi, “Microwave assisted process intensification and kinetic modelling: extraction of camptothecin from Nothapodytes nimmoniana plant,” Industrial Crops and Products, vol. 98, pp. 60–67, 2017.
View at: Publisher Site | Google Scholar
N. Chumnanpaisont, C. Niamnuy, and S. Devahastin, “Mathematical model for continuous and intermittent microwave-assisted extraction of bioactive compound from plant material: Extraction of β-carotene from carrot peels,” Chemical Engineering Science, vol. 116, pp. 442–451, 2014.
View at: Publisher Site | Google Scholar
X. Zheng, X. Wang, Y. Lan, J. Shi, S. J. Xue, and C. Liu, “Application of response surface methodology to optimize microwave-assisted extraction of silymarin from milk thistle seeds,” Separation and Purification Technology, vol. 70, no. 1, pp. 34–40, 2009.
View at: Publisher Site | Google Scholar
P. Pongmalai, S. Devahastin, N. Chiewchan, and S. Soponronnarit, “Enhancement of microwave-assisted extraction of bioactive compounds from cabbage outer leaves via the application of ultrasonic pretreatment,” Separation and Purification Technology, vol. 144, pp. 37–45, 2015.
View at: Publisher Site | Google Scholar
Y. Ando, S. Hagiwara, and H. Nabetani, “Thermal inactivation kinetics of pectin methylesterase and the impact of thermal treatment on the texture, electrical impedance characteristics and cell wall structure of Japanese radish (Raphanus sativus L.),” Journal of Food Engineering, vol. 199, pp. 9–18, 2017.
View at: Publisher Site | Google Scholar
Y. Xin, M. Zhang, B. Xu, B. Adhikari, and J. Sun, “Research trends in selected blanching pretreatments and quick freezing technologies as applied in fruits and vegetables: a review,” International Journal of Refrigeration, vol. 57, article no. 3030, pp. 11–25, 2015.
View at: Publisher Site | Google Scholar
X. Sun, W. Li, J. Li et al., “Process optimisation of microwave-assisted extraction of peony (Paeonia suffruticosa Andr.) seed oil using hexane-ethanol mixture and its characterisation,” International Journal of Food Science and Technology, vol. 51, no. 12, pp. 2663–2673, 2016.
View at: Publisher Site | Google Scholar
X. Zheng, F. Yin, C. Liu, and X. Xu, “Effect of process parameters of microwave assisted extraction (MAE) on polysaccharides yield from pumpkin,” Journal of Northeast Agricultural University (English edition), vol. 18, no. 2, pp. 79–86, 2011.
View at: Publisher Site | Google Scholar
J. R. Sarkis, D. P. Jaeschke, I. C. Tessaro, and L. D. F. Marczak, “Effects of ohmic and conventional heating on anthocyanin degradation during the processing of blueberry pulp,” LWT- Food Science and Technology, vol. 51, no. 1, pp. 79–85, 2013.
View at: Publisher Site | Google Scholar
W. J. Liu, X. Wang, and J. H. Du, “Review on isolation, purification and qualitative and quantitative analysis method of anthocyanin,” China Food Additives, vol. 6, pp. 178–182, 2010.
View at: Google Scholar

Copyright

Copyright © 2018 Hongkun Xue et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

3467

Downloads

1504

Citations