Abstract
Numerical prediction is performed on the reduction of wüstite under simulated blast furnace conditions using factorial design approach. Wüstite sinter samples with different basicity (0.5, 1.0, and 2.0) are reduced with a gas mixture consisting of 30% CO, 10% H2, 5% CO2, and 55% N2 at 950–1100°C. In all cases, the reduction degree of wüstite increased with basicity and temperature. A 23 factorial design is applied to derive a regression model based on the experimental data of acidic (CaO/SiO2 = 0.5) and basic (CaO/SiO2 = 2.0) wüstite which is reduced at 950°C and 1100°C for 5 and 35 min. The developed mathematical model is applied to predict the reduction degree of wüstite at different basicity (0.5, 1.0, and 2.0), interval of time (5–35 min), and temperatures (950, 1000, 1050°C, and 1100°C). In general, the results of the driven models are found to be in good agreement with the experimental data of reduction of wüstite in many cases. The MATLAB program is used to carry out the required calculations.
1. Introduction
The use of mathematical models in the experimental analysis has increased over the years due to its efficiency in explaining, predicting, and controlling the processes [1]. Recently, the factorial design offers an efficient method that can be used to estimate not only the effect of each individual parameter but also the interaction combination of different operational parameters on the overall process [2]. In the blast furnace, the reduction step from wüstite to metallic iron is considered the rate controlling step which has a great influence on the coke consumption and the blast furnace efficiency. Therefore, many studies have been carried out to estimate the reduction kinetics and mechanism of wüstite to metallic iron. The effect of basicity on the reduction behavior of wüstite sinter was studied [3]. The reduction rate was the highest in basic wüstite sinter due to the formation of highly reducible calcium ferrites while the acidic wüstite exhibited the lowest reduction due to the formation of hardly reducible fayalite and ferrobustamite phases. The reduction of basic sinter and acidic pellets under simulated blast furnace condition has been studied [4–6]. The acidic sinter showed higher reduction rate compared to that of basic sinter at the initial stages due to the higher porosity. As the reduction proceeded, the formation of fayalite phase adversely affected the reduction of pellets. The influence of fluxing oxides (CaO and/or MgO) on the reduction of wüstite was examined [7]. The reduction of wüstite to metallic iron was promoted in presence of fluxing oxides at the early stages of reduction, while a slowdown was observed at the latter stages due to the formation of magnesiowüstite. Another study which was carried on pure and wüstite doped with CaO/SiO2 (basicity ratio: 0.2, 0.5, and 0.8) indicated that the reduction decreased as the basicity increased [8]. The effect of SiO2 and/or Al2O3 on the reduction of wüstite was investigated [9]. The Al2O3 was found to decrease the reduction rate in the whole range of applied temperature, 670–930°C. On the other hand, the simultaneous dissolution of SiO2 and Al2O3 in wüstite resulted in acceleration of the reduction process. The influence of temperature and gas composition on the reduction of wüstite was studied [10]. It was reported that the effect of temperature on increasing the reduction rate of wüstite was significant as the reduction proceeded while the effect of gas composition was not clear all over the reduction process. The reduction of wüstite by H2 gas at 450–600°C was investigated [11]. The reduction mechanism was found to be dependent on the eutectoid decomposition temperature at 530°C. At temperature higher than 530°C, wüstite was reduced directly to metallic iron while at lower temperature the reduction was accomplished through two sequential steps: (i) decomposition of wüstite to magnetite and metallic iron (4FeO = Fe3O4 + Fe); (ii) reduction of magnetite with H2 to metallic iron (Fe3O4 + 4H2 = 3Fe + 4H2O). In the reduction of dense wüstite with H2 at 670–930°C, it was reported that a small addition of SiO2 (0.2%) promoted the reducibility of wüstite at >800°C, while it decreased the reduction at <730°C [9].
The previous survey summarized some studies that have been carried out experimentally to elucidate the effect of some factors on the reduction rate of wüstite. However, the effective magnitude of these factors either individually or collectively on the reduction rate of wüstite sinter is still not clear. This can be carried out by the application of statistical factorial design approach which has several advantages in highlighting the effect of individual variables and their relative importance on the reduction process [12, 13]. In the current study, a 23 factorial design is used to precisely estimate the individual and mutual interactions of three main parameters including basicity, interval of time, and temperature on the reduction rate of wüstite sinter. The effect of other parameters such as impurities (MgO, Al2O3, MnO2, TiO2, and BaO), sample size and shape, gas composition, and porosity will be considered in further investigations. The current factorial design is built on the experimental data of wüstite sinter which has different basicity (CaO/SiO2: 0.5, 1.0, and 2.0) and reduced with simulated blast furnace shaft gas (30% CO; 10% H2; 5% CO2; 55% N2) at 950–1100°C. The calculations have been carried out by MATLAB program.
2. Materials and Methods
In the current study, pure chemical Fe2O3, CaO, and SiO2 were used to eliminate the effect of other impurities which normally exist in the iron ore and affect the reduction process. Pure sinter mixtures with different basicity (CaO/SiO2: 0.5, 1.0, and 2.0) are prepared. The acidic mixture with basicity equal to 0.5 consisted of 85% Fe2O3, 5% CaO, and 10% SiO2. The neutral mixture with basicity equal to 1.0 is composed of 85% Fe2O3, 7.5% CaO, and 7.5% SiO2. The basic mixture with basicity equal to 2.0 consists of 85% Fe2O3, 10% CaO, and 5% SiO2. The oxide powders were mixed well in a ball-mill to guarantee the complete homogeneity of the mixtures. Equal weights of ~2.0 g of each mixture were pressed in a cylindrical mould of ~1.0 cm inner diameter at 10 kN using a hydraulic press. Under these conditions equal size compacts (diameter = 0.99 cm and height = 1.0 cm) have been prepared. The compacts were dried at 100°C for 24 hours, then fired in a muffle furnace up to 1300°C with heating rate 10 K/min, and kept at this temperature for 1.0 h to ensure the complete reactions between different oxides (Fe2O3, CaO, and SiO2). The prepared sinters (acidic, neutral, and basic) were fast cooled down in air to room temperature and then kept in a desiccator for subsequent reduction experiments.
The reduction experiments have been carried out in a vertical tube furnace as shown in Figure 1. The system consisted of an automatic sensitive balance (B) equipped with a vertical tube furnace (F). Alumina reaction tube (A) was fitted inside the furnace. The output of the balance (O) was connected to the recording system (R) for continuous measuring of the total weight loss during the reduction process as a function of time. The flow rate and the composition of the reduced gas are adjusted through digital flow meters (D). The actual temperatures of the furnace (T1) and sample (T2) were measured with controller (K). Purified N2 at constant flow rate of 1.0 liter/min was introduced into the reaction tube during the heating up of the furnace. At the applied temperature, the sintered compact (C) was placed in a platinum basket (P) and suspended from the balance arm by platinum wire (W). The sinter sample was positioned in the reaction tube at the middle of hot zone. After soaking the sample at 900°C for 10 minutes, a gas composition which consists of 20% CO, 20% CO2, 5% H2, and 55% N2 was applied for the prereduction of sinters to wüstite. After reaching a constant weight, the temperature was increased to 950, 1000, 1050, or 1100°C in presence of pure N2. The reduction of wüstite is started with gas mixture consisting of 30% CO, 5.0% CO2, 10% H2, and 55% N2. Both gas mixtures which are applied for prereduction of sinter to wüstite and the further reduction of wüstite to metallic iron are selected to simulate the gas composition in the blast furnace at the upper and lower shaft. The flow rate of gas mixture was always constant at 1.0 liter/min. During the reduction experiment, the weight loss was continuously recorded as a function of time till the sample weight became constant. At the end of experiment, the reduced sinter was pulled up to the cooled zone of the reaction tube in presence of purified N2 flow and dropped out, by releasing the suspension wire from the balance, into a conical flask containing acetone to prevent the reoxidation. The reduction degree of wüstite was calculated based on the following: where is the reduction degree of wüstite, the initial weight of wüstite sample before reduction, the final weight of sample after reduction, and the total weight loss when the sample is completely reduced.
3. Results and Discussion
3.1. Experimental Results
The sinter samples which prereduced to wüstite with 20% CO, 20% CO2, 5% H2, and 55% N2 at 900°C were subsequently reduced with 30% CO, 5% CO2, 10% H2, and 55% N2 at 950–1100°C. The reduction curves of wüstite sinters at 950°C, 1000°C, 1050°C, and 1100°C are given in Figures 2(a)–2(d), respectively. At each applied temperature, the highest reduction degree and reduction rate are exhibited in basic wüstite sinter (B = CaO/SiO2 = 2.0) followed by neutral wüstite sinter (B = CaO/SiO2 = 1.0) and finally acidic wüstite sinter (B = CaO/SiO2 = 0.5). The higher reduction rate of basic wüstite sinter was attributed to the formation of highly reducible calcium ferrites on account of wüstite (2CaO + 3FeO → 2CaO·Fe2O3 + Fe), while the lower reduction rate of acidic wüstite sinter was attributed to the formation of hard reducible fayalite (2FeO·SiO2) and ferrobustamite ((Ca0.5Fe0.5)SiO3) phases. The reduction kinetics and mechanism of highly basic and acidic wüstite were thoroughly discussed elsewhere [3]. In the current study, a 23 factorial design is applied to the experimental data of wüstite sinter at the highest and lowest basicity ( = 0.5 and 2.0) and temperature (950°C and 1100°C). The reduction time is selected at 5 and 35 min which represent the initial and moderate reduction stages. Each trail was repeated two times under the same conditions in order to confirm the results reproducibility. The experimental data are given in Table 1.
(a)
(b)
(c)
(d)
3.2. Model Description
3.2.1. Definition of the Controlling Parameters
The controlling parameters which are considered in the current applied 23 factorial design are including the effect of basicity (CaO/SiO2), reduction time, and temperature on reduction process of wüstite sinter.
By convention, the effect of a factor was denoted by a capital Latin letter. Thus “” refers to the effect basicity (CaO/SiO2), “” refers to the effect of time, “” refers to the effect of reduction temperature, “” refers to the interaction effect of basicity and time, “” refers to interaction effect of basicity and temperature, and “” refers to the interaction effect of time and temperature, while “” refers to the interaction effect of basicity, time, and temperature. The low and high levels of , , and are denoted by “–” and “+”, respectively. The eight treatment combinations in the design are usually represented by lowercase letters. The high level of any factor in the treatment combination is denoted by the corresponding lowercase letter (, , , , , , and ), while the low level of any factor will be indicated by the absence of its corresponding letter. Thus, “” represents the treatment combination of (basicity) at high level with (time) and (temperature) at low levels, “” represents at high level with and at low levels, “” represents and factors at the high levels with at low level, “” represents and at high levels with at low level, “” represents and at high levels with at low level, “” represents , , and factors at the high levels, and finally is used to denote all of the factors at low level.
The average effect of any factor can be defined as the change in response produced by a change in the level of that factor averaged over the levels of the other factors. The symbols , , , , , , , and represent the total of all 2 replicates taken at the treatment combination, that is, ().
3.2.2. Mathematical Formulations
Mathematical formulations are used to estimate the effect of different parameters on the reduction degree of wüstite sinter. The effect of at low levels of and is []/, the effect of at high levels of and is []/, the effect of at low level of and high level of is []/, and the effect of at high level of and low level of is []/. The main effect of is the average quantities of its effect at low and high levels of and as given in the following: The average main effect of and can be calculated in the same manner of as given in the following: The interaction effect of is one half of the difference between the averages of effect at the two levels of . The average effect of at high level of is [() + ()]/2, and the average effect of at low level of is [() + ()]/2. Based on this, the interaction AB effect can be given in the following: In similar way, the average effect of and can be calculated as give in the following: The interaction effect is defined as the average difference between the interaction for the two different levels of as given in the following:
3.3. Model Application
Table 2 summarizes the plus and minus signs that can be developed from the contrasts, where the high level is referred to by plus sign (+) and low level is referred to by minus sign (−). The signs of identity element are plus.
Sum of squares for the effects in the 23 design with replicates is SS = (Contrast)2/8. The total sum of squares () has degrees of freedom and the error sum of squares () has degrees of freedom. They can be calculated by using (9) and (10), respectively. Table 3 summarizes the main effects of variables, sum of squares, and the mean square: where is the reduction degree observation and is the mean reduction degree of all observation.
From the data given in Table 3, it can be seen that the highest positive effect on the reduction degree of wüstite is exhibited by the interval of time followed by the basicity and then the applied temperature. The binary interaction between the parameters showed the highest positive effect on the reduction of wüstite for basicity with time followed by time with temperature and then basicity with temperature. The ternary interaction between the basicity, time, and temperature exhibited a negative effect on the reduction degree of wüstite.
The contrast coefficients which are used to estimate the effects are summarized in Table 4. The contrast coefficient is always either (+1) or (−1) which is referring to the maximum and minimum level of the affecting factor.
The results of the experiment can be expressed in terms of regression model. The regression model is given in the following: where is the predicted reduction degree, %; , , and are coded variables that represent the basicity, time, and temperature, respectively. is the intercept which is the grand average of all 16 observations (i.e., = 46.6245), the regression coefficients , , and are one-half the corresponding factors , , and , respectively, ( = 10.5038, = 29.3628, and = 8.5234), the regression coefficients , , , and are one-half the corresponding factors , , , and , respectively, which are ( = 3.2864, = 1.3075, , and ), and is the residual (the difference between observed and fitted point of the design). Equation (11) can be given with regression coefficients values as shown in the following: To estimate the residual () and to calculate the predicted RD at , , , , , , , and , the sign of coded variables can be taken from Table 2. The resuts are presented in Table 5. The average residual is ±0.12 which can be neglected.
The relation between the natural variable and the coded variable can be given as follows: the coded variable is equal to [(natural variable − 1/2(variable at high level + variable at low level))/1/2(variable at high level − variable at low level)]. Based on this, the RD can be predicted in terms of basicity, time, and temperature as given in the full regression model formulation in (13). This equation covers basicity from 0.5–2.0, reduction time 5–35 min, within temperature range 950–1100°C: where is the basicity (CaO/SiO2), is reduction time in min, and is the temperature in °C.
This full regression formulation indicates that the reduction degree of wüstite sinter is not only affected by the individual parameter (basicity, time, or temperature) but also by the mutual interactions among all of these parameters.
3.4. Validation of the Regression Model
In order to examine the validity and the efficiency of the current regression model the derived equation is used to estimate the reduction degree of wüstite at different basicity (0.5, 1.0, and 2.0), reduction time (5, 10, 15, 20, 25, 30, and 35 min), and temperatures (950°C, 1000°C, 1050°C, and 1100°C). The results are compared to that obtained from the experimental reduction trails as can be seen in Figure 3. It can be seen that the predicted values of the reduction of wüstite are very close and in a good agreement to the average experimetal results at relatively low temperature at 950°C and 1000°C. As the temperature increased (1050°C), deviations to different extents appeared and it becomes siginficant at the intermediate stages of reduction of high basic wüstite sinter ( = 2.0). This can be attributed to the effect of temperature on the enhancement of the reduction of calcium ferrites which are formed on account of wüstite as shown in the following: Based on the previous findings, the derived regression model is able to predict the reduction values in many cases especially at lower temperature (≤1000°C) and lower basicity. In highly basic wüstite, the formation of calcium ferrites enhanced the reduction rate at high temperature which resulted in a significant deviation compared to that calculated by the regression model.
(a)
(b)
(c)
(d)
4. Conclusions
In the current study, wüstite sinter with different basicity (CaO/SiO2 = 0.5, 1.0, and 2.0) was prepared and reduced with 30% CO, 5% CO2, 10% H2, and 55% N2 at 950–1100°C. A 23 factorial design is built on the experimetal data of reduction at lowest and highest basicity and reduction tempeartures. The main findings can be summarized in the following points.(1)The higest reduction degree was exhibited by the basic wüstite sinter (CaO/SiO2 = 2.0) which followed neutral wustite (CaO/SiO2 = 1.0) and the lowest by acidic wüstite sinter (CaO/SiO2 = 0.5).(2)A full regression formulation was develpoed to calculate the reduction degree (RD) of wüstite based on basicity (), time (), and temperature (): (3)The highest positive effect on the reduction degree was exhibited by the interval of time followed by basicity and then the applied temperature. In the binary interaction, the basicity with time exhibited the highest positive effect on the reduction of wüstite followed by time with temperature and then basicity with temperature. The ternary interaction between the basicity, time, and temperature showed a negative effect on the reduction degree of wüstite.(4)The validation of the regression model exhibited a good agreement with the experimental results at relatively low temperature (≤1000°C). A significant deviation was obtained at high temperature (≥1050°C) which was attributed to the formation of highly reducible calcium ferrite phase.
Conflict of Interests
The author declares that there is no conflict of interests regarding the publication of this paper.