Table of Contents
Journal of Metallurgy
Volume 2016, Article ID 6178790, 11 pages
http://dx.doi.org/10.1155/2016/6178790
Research Article

Through-Thickness Compression Testing of Commercially Pure (Grade II) Titanium Thin Sheet to Large Strains

Department of Chemical Engineering and Materials Science, University of Southern California, Los Angeles, CA 90089, USA

Received 1 July 2016; Accepted 30 August 2016

Academic Editor: Menahem Bamberger

Copyright © 2016 K. K. Smith and M. E. Kassner. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. U. F. Kocks, M. G. Stout, and A. D. Rollett, “The influence of texture on strain hardening,” in Proceedings of the Conference on the Strength of Metals and Alloys (ICSMA '88), P. O. Kettunen, T. K. Lepistö, and M. E. Lehtonen, Eds., pp. 25–34, Tampere, Finland, August 1988.
  2. M. Battaini, E. V. Pereloma, and C. H. J. Davies, “Orientation effect on mechanical properties of commercially pure titanium at room temperature,” Metallurgical and Materials Transactions A, vol. 38, no. 2, pp. 276–285, 2007. View at Publisher · View at Google Scholar · View at Scopus
  3. A. V. Podolskiy, H. P. Ng, I. A. Psaruk, E. D. Tabachnikova, and R. Lapovok, “Equal channel angular pressing at temperatures of 77-575K of titanium grade 2: microstructure and mechanical behavior,” IOP Conference Series: Materials Science and Engineering, vol. 63, Article ID 012071, 2014. View at Google Scholar
  4. F.-W. Long, Q.-W. Jiang, L. Xiao, and X.-W. Li, “Compressive deformation behaviors of coarse- and ultrafine-grained pure titanium at different temperatures: a comparative study,” Materials Transactions, vol. 52, no. 8, pp. 1617–1622, 2011. View at Publisher · View at Google Scholar · View at Scopus
  5. S. Nemat-Nasser, W. G. Guo, and J. Y. Cheng, “Mechanical properties and deformation mechanisms of a commercially pure titanium,” Acta Materialia, vol. 47, no. 13, pp. 3705–3720, 1999. View at Publisher · View at Google Scholar · View at Scopus
  6. A. A. Salem, S. R. Kalidindi, and R. D. Doherty, “Strain hardening regimes and microstructure evolution during large strain compression of high purity titanium,” Scripta Materialia, vol. 46, no. 6, pp. 419–423, 2002. View at Publisher · View at Google Scholar · View at Scopus
  7. R. L. Goetz and S. L. Semiatin, “The adiabatic correction factor for deformation heating during the uniaxial compression test,” Journal of Materials Engineering and Performance, vol. 10, no. 6, pp. 710–717, 2001. View at Publisher · View at Google Scholar · View at Scopus
  8. W. Schroeder and D. A. Webster, “Press-forging thin sections: effect of friction, area, and thickness on pressures required,” Journal of Applied Mechanics, vol. 16, article 289, 1949. View at Google Scholar
  9. ASTM International, “Standard Test Methods of Compression Testing of Metallic Materials at Room Temperature,” Designation: E9-89a (Reapproved 2000), 1–9, 1989.
  10. M. E. Nixon, O. Cazacu, and R. A. Lebensohn, “Anisotropic response of high-purity α-titanium: experimental characterization and constitutive modeling,” International Journal of Plasticity, vol. 26, no. 4, pp. 516–532, 2010. View at Publisher · View at Google Scholar · View at Scopus
  11. A. Akhtar, “Basal slip and twinning in α-titanium single crystals,” Metallurgical Transactions A, vol. 6, no. 5, pp. 1105–1113, 1975. View at Publisher · View at Google Scholar · View at Scopus
  12. S. V. Kailas, Y. V. R. K. Prasad, and S. K. Biswas, “Influence of initial texture on the microstructural instabilities during compression of commercial α-titanium at 25 °C to 400 °C,” Metallurgical and Materials Transactions A, vol. 25, no. 7, pp. 1425–1434, 1994. View at Publisher · View at Google Scholar · View at Scopus
  13. B. A. Baumgarten, D. S. Tordonato, and W. F. Kepler, “Investigation of molybdenum disulfide and tungsten disulfide as additives to coating for foul release systems,” in Reclamation: Managing Water in the West, pp. 1–14, Materials Engineering and Research Laboratory, Denver, Colo, USA, 2011. View at Google Scholar
  14. CRC Industries, Dry Moly Lube Technical Data Sheet, Industrial Products Division, Westminster, Pa, USA, 2011.
  15. M. E. Kassner, J. Pollard, E. Evangelista, and E. Cerri, “Restoration mechanisms in large-strain deformation of high purity aluminum at ambient temperature and the determination of the existence of steady-state,” Acta Metallurgica et Materialia, vol. 42, no. 9, pp. 3223–3230, 1994. View at Publisher · View at Google Scholar · View at Scopus
  16. T.-S. Jun, Z. Zhang, G. Sernicola, F. P. E. Dunne, and T. B. Britton, “Local strain rate sensitivity of single α phase within a dual-phase Ti alloy,” Acta Materialia, vol. 107, pp. 298–309, 2016. View at Publisher · View at Google Scholar · View at Scopus
  17. D. R. Chichili, K. T. Ramesh, and K. J. Hemker, “The high-strain-rate response of alpha-titanium: experiments, deformation mechanisms and modeling,” Acta Materialia, vol. 46, no. 3, pp. 1025–1043, 1998. View at Publisher · View at Google Scholar · View at Scopus
  18. M. A. Meyers, G. Subhash, B. K. Kad, and L. Prasad, “Evolution of microstructure and shear-band formation in α-hcp titanium,” Mechanics of Materials, vol. 17, no. 2-3, pp. 175–193, 1994. View at Publisher · View at Google Scholar · View at Scopus
  19. D. Peykov, E. Martin, R. R. Chromik, R. Gauvin, and M. Trudeau, “Evaluation of strain rate sensitivity by constant load nanoindentation,” Journal of Materials Science, vol. 47, no. 20, pp. 7189–7200, 2012. View at Publisher · View at Google Scholar · View at Scopus
  20. R. E. Reed-Hill, C. V. Iswaran, and M. J. Kaufman, “A power law model for the flow stress and strain-rate sensitivity in CP titanium,” Scripta Metallurgica et Materiala, vol. 33, no. 1, pp. 157–162, 1995. View at Publisher · View at Google Scholar · View at Scopus
  21. F. Wang, B. Li, T. T. Gao, P. Huang, K. W. Xu, and T. J. Lu, “Activation volume and strain rate sensitivity in plastic deformation of nanocrystalline Ti,” Surface and Coatings Technology, vol. 228, no. 1, pp. S254–S256, 2013. View at Publisher · View at Google Scholar · View at Scopus
  22. R. Horiuchi, J. Kaneko, A. B. Elsebai, and M. M. Sultan, Report No. 443, Institute of Space and Aerospace Science, University of Tokyo, Tokyo, Japan, 1970.
  23. CRC Industries, Dry Graphite Lube Technical Data Sheet, Industrial Products Division, Westminster, Pa, USA, 2013.
  24. Carr Supply Company, More about plastics [M.S. thesis], 2015.