Table of Contents
Journal of Nonlinear Dynamics
Volume 2017, Article ID 6594861, 20 pages
https://doi.org/10.1155/2017/6594861
Research Article

System Performance of an Inertially Stabilized Gimbal Platform with Friction, Resonance, and Vibration Effects

1Department of Electrical and Computer Engineering, College of Engineering and Computer Science, California State University Northridge, Los Angeles, CA 91330, USA
2Mechanical Engineering Department, College of Engineering and Computer Science, California State University Northridge, Los Angeles, CA 91330, USA
3Northrop Grumman Corporation, Woodland Hills, CA 91367, USA

Correspondence should be addressed to Ruting Jia; ude.nusc@aij.gnitur

Received 3 January 2017; Accepted 16 February 2017; Published 28 March 2017

Academic Editor: Huai-Ning Wu

Copyright © 2017 Ruting Jia et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. J. M. Hilkert, “Inertially stabilized platform technology: concepts and principles,” IEEE Control Systems Magazine, vol. 28, no. 1, pp. 26–46, 2008. View at Publisher · View at Google Scholar · View at MathSciNet · View at Scopus
  2. M. K. Masten, “Inertially stabilized platforms for optical imaging systems,” IEEE Control Systems Magazine, vol. 28, no. 1, pp. 47–64, 2008. View at Publisher · View at Google Scholar · View at MathSciNet · View at Scopus
  3. J. Debruin, “Control systems for mobile satcom antennas,” IEEE Control Systems Magazine, vol. 28, no. 1, pp. 86–101, 2008. View at Publisher · View at Google Scholar · View at MathSciNet · View at Scopus
  4. M. Abdo, A. R. Toloei, A. R. Vali, and M. R. Arvan, “Modeling, control and simulation of cascade control servo system for one axis gimbal mechanism,” International Journal of Engineering, Transactions A: Basics, vol. 27, no. 1, pp. 157–170, 2014. View at Publisher · View at Google Scholar · View at Scopus
  5. N. Layshot, Modeling of a gyro-stabilized helicopter camera system using neural networks [M.S. thesis], California Polytechnic State University, San Luis Obispo, Calif, USA, 2010.
  6. J. Johansson, Modeling and control of an advanced camera Gimbal [M.S. thesis], Linkpings Univeritet, Linköping, Sweden, 2012.
  7. A. Lawrence, Modern Inertial Technology: Navigation, Guidance, and Control, Springer, 2nd edition, 2012.
  8. Z. Hurák and M. Řezáč, “Image-based pointing and tracking for inertially stabilized airborne camera platform,” IEEE Transactions on Control Systems Technology, vol. 20, no. 5, pp. 1146–1159, 2012. View at Publisher · View at Google Scholar · View at Scopus
  9. I. Rusnak, “Family of the PID controllers,” in Introduction to PID Controllers—Theory, Tuning and Application to Frontier Areas, R. C. Panda, Ed., chapter 2, InTech, Rijeka, Croatia, 2012. View at Publisher · View at Google Scholar
  10. Y. S. Kwon, H. Y. Hwang, and Y. S. Choi, “Stabilization loop design on direct drive gimbaled platform with low stiffness and heavy inertia,” in Proceedings of the International Conference on Control, Automation and Systems (ICCAS '07), pp. 320–325, IEEE, Seoul, South Korea, October 2007. View at Publisher · View at Google Scholar · View at Scopus
  11. M. Kang, W. Yoon, and J. Lee, “LOS(line-of-sight) stabilization control of OTM(on-the-move) antenna driven by geared flexible transmission mechanism,” Transactions of the Korean Society for Noise and Vibration Engineering, vol. 21, no. 10, pp. 951–959, 2011. View at Publisher · View at Google Scholar
  12. A. Eielsen, M. Burger, J. Gravdahl, and K. Pettersen, “PI2-controller applied to a piezoelectric nanopositioner using conditional integrators and optimal tuning,” IFAC Proceedings Volumes, vol. 44, no. 1, pp. 887–892, 2011, Proceedings of the 18th World Congress of the International Federal Automatic Control, January 2011. View at Publisher · View at Google Scholar
  13. S. Aggarwal, M. Garg, and A. Swarup, “Design of feedback controller for non-minimum phase nano positioning system,” Advanced Materials Letters, vol. 4, no. 1, pp. 31–34, 2013. View at Publisher · View at Google Scholar · View at Scopus
  14. K.-J. Seong, H.-G. Kang, B.-N. Yeo, and H.-P. Lee, “The stabilization loop design for a two-axis gimbal system using LQG/LTR controller,” in Proceedings of the SICE-ICASE International Joint Conference, pp. 755–759, Busan, Korea, October 2006. View at Publisher · View at Google Scholar · View at Scopus
  15. L. Márton and B. Lantos, “Modeling, identification, and compensation of stick-slip friction,” IEEE Transactions on Industrial Electronics, vol. 54, no. 1, pp. 511–521, 2007. View at Publisher · View at Google Scholar · View at Scopus
  16. K. Hashiguchi and S. Ozaki, “Constitutive equation for friction with transition from static to kinetic friction and recovery of static friction,” International Journal of Plasticity, vol. 24, no. 11, pp. 2102–2124, 2008. View at Publisher · View at Google Scholar · View at Zentralblatt MATH · View at Scopus
  17. B. S. Ünlü and E. Atik, “Determination of friction coefficient in journal bearings,” Materials and Design, vol. 28, no. 3, pp. 973–977, 2007. View at Publisher · View at Google Scholar · View at Scopus
  18. C. Hsieh and Y.-C. Pan, “Dynamic behavior and modelling of the pre-sliding static friction,” Wear, vol. 242, no. 1-2, pp. 1–17, 2000. View at Publisher · View at Google Scholar · View at Scopus
  19. B. Armstrong, “Friction: experimental determination, modeling and compensation,” in Proceedings of the 1988 IEEE International Conference on Robotics and Automation, 1988. View at Publisher · View at Google Scholar
  20. X. Tan, A. Modafe, and R. Ghodssi, “Measurement and modeling of dynamic rolling friction in linear microball bearings,” Journal of Dynamic Systems, Measurement and Control, vol. 128, no. 4, pp. 891–898, 2006. View at Publisher · View at Google Scholar · View at Scopus
  21. K. De Moerlooze and F. Al-Bender, “On the relationship between normal load and friction force in pre-sliding frictional contacts. Part 2: experimental investigation,” Wear, vol. 269, no. 3-4, pp. 183–189, 2010. View at Publisher · View at Google Scholar · View at Scopus
  22. A. L. Demirel and S. Granick, “Transition from static to kinetic friction in a model lubricated system,” Journal of Chemical Physics, vol. 109, no. 16, pp. 6889–6897, 1998. View at Publisher · View at Google Scholar · View at Scopus
  23. D. R. Otlowski, K. Wiener, and B. A. Rathbun, “Mass properties factors in achieving stable imagery from a gimbal mounted camera,” in Airborne Intelligence, Surveillance, Reconnaissance (ISR) Systems and Applications V, vol. 6946 of Proceedings of SPIE, Orlando, Fla, USA, March 2008. View at Publisher · View at Google Scholar
  24. J. Johnson and D. Priser, “Vibration levels in army helicopters—measurement recommendations and data,” USAARL Report 81-5, 1981. View at Google Scholar
  25. P. Konstanzer and B. Enekl, “Recent advances in Eurocopter's passive and active vibration control,” in Proceedings of the American Helicopter Society 64th Annual Forum, Montréal, Canada, April 2008.