Electrodeposition of Platinum and Ruthenium Nanoparticles in Multiwalled Carbon Nanotube-Nafion Nanocomposite for Methanol Electrooxidation

Hong, Yu-Huei; Tsai, Yu-Chen

doi:https://doi.org/10.1155/2009/892178

Journal of Nanomaterials

On this page

Abstract Introduction Experimental Results and Discussion Conclusion Acknowledgments References Copyright Related Articles

Research Article | Open Access

Volume 2009 | Article ID 892178 | https://doi.org/10.1155/2009/892178

Electrodeposition of Platinum and Ruthenium Nanoparticles in Multiwalled Carbon Nanotube-Nafion Nanocomposite for Methanol Electrooxidation

Yu-Huei Hong¹and Yu-Chen Tsai¹

Academic Editor: Zhi-Li Xiao

Received27 May 2009

Accepted25 Aug 2009

Published08 Nov 2009

Abstract

PtRu nanoparticles with a diameter of 10–15 nm were electrodeposited within multiwalled carbon nanotube-Nafion (MWCNT-Nafion) nanocomposite. The formation of PtRu nanoparticles in MWCNT-Nafion nanocomposite was characterized by scanning electron microscopy, transmission electron microscopy, and energy dispersive X-ray spectroscopy. The electrocatalytic activity towards the methanol electrooxidation at PtRu-MWCNT-Nafion and Pt-MWCNT-Nafion nanocomposite-modified glassy carbon electrodes was investigated by cyclic voltammetry. The results indicated that the PtRu-MWCNT-Nafion nanocomposite was electrocatalytically more active than Pt-MWCNT-Nafion nanocomposite. The effect of atomic ratio of Pt : Ru on the electrocatalytic ability towards the methanol electrooxidation was investigated in order to achieve a high catalyst use. The PtRu bimetallic catalyst with 1 : 1 atomic ratio showed better electrocatalytic activity towards the methanol electrooxidation. The stability for the methanol electrooxidation at PtRu-MWCNT-Nafion nanocomposite modified was also investigated.

1. Introduction

Direct methanol fuel cell is an attractive power source for portable power applications and in electrical vehicles [1]. The anodic oxidation of methanol on electrode surfaces in acidic electrolytes is a catalytic reaction, in which the CO₂ and six electrons were produced. The main factors that limit the practical application of direct methanol fuel cell are the sluggish kinetics of methanol electrooxidation at anode and the poisoning of electrode surfaces. Therefore, the development of highly effective methanol electrooxidation catalysts seems very attractive. Pt shows a good electrocatalytic activity towards the methanol electrooxidation; however, it is easily poisoned by CO, the intermediates of methanol electrooxidation. Much effort has been made to develop Pt-based catalysts with higher CO poisoning tolerance and electrocatalytic activity. Improved electrocatalytic activity towards the methanol electrooxidation has been reported for Pt-based catalysts with other elements such as Ru [2], Sn [3], and Os [4, 5]. Among these Pt-based catalysts, PtRu bimetallic catalyst has shown the best electrocatalytic activity towards the methanol electrooxidation. The improvement of electrocatalytic activity towards the methanol electrooxidation with PtRu catalyst can be ascribed to the bifunctional mechanism. The CO removal process is achieved at PtRu catalyst because of the reaction of Ru-OH groups with neighboring CO adsorbed on Pt [1].

Metal nanoparticles possess a high catalytic efficiency and a large surface-to-volume ratio [6–12]. A large variety of methods including impregnation [13], colloidal deposition [14], supercritical fluid [15], and electrodeposition [16] have been reported for the synthesis of PtRu nanoparticles. The electrochemical route is an effective procedure when compared with others which are complexity of the fabrication steps and impurity might be involved during the preparation. The synthesis of PtRu nanoparticles on a suitable catalyst support which provides dispersion and stability is important in the field of direct methanol fuel cell. In recent studies, carbon nanotubes (CNTs) have been considered as a promising material for catalyst support because of their good electrical conductivity, high chemical stability, and large surface-to volume ratio [17]. The applications of CNTs in fuel cells as a catalyst support have been reported in literature [18–20].

Nafion has been used as a medium for dispersion of CNTs in aqueous solution [21, 22]. By the combination of multiwalled carbon nanotube (MWCNTs) and Nafion, a stable electroanalytical nanocomposite film of MWCNT-Nafion can be prepared by a simple solvent casting process. MWCNT-Nafion-modified glassy carbon electrodes have been applied to electroanalytical applications [23, 24]. The aim of this study is to electrodeposite PtRu nanoparticles in MWCNT-Nafion nanocomposite in order to improve its electrocatalytic behavior for the methanol electrooxidation. The effect of the atomic composition of PtRu on the electrocatalytic ability towards the electrochemical oxidation of methanol is investigated and discussed.

2. Experimental

2.1. Reagents

K₂PtCl₆ was obtained from Acros. Ruthenium(III) chloride hydrate and methanol were supplied by Sigma. Nafion (5 wt% in lower aliphatic alcohol) was purchased from Aldrich. Sulfuric acid was obtained from Fluka. The MWCNTs (TECO Nanotech Co., Ltd., Taiwan) used in this study were of 99% purity and synthesized by an electric arc discharge method. The reagents were used as purchased without further pretreatment. In this study, all solutions were prepared with deionized water of resistivity not less than 18 cm taken from a Milli-Q water purification system (Milli-Q, USA).

2.2. Apparatus

Electrochemical experiments were performed with an Autolabe PGSTA30 Electrochemical Analyzer (Eco Chemie, Netherlands). A conventional three-electrode system was carried out with a glassy carbon working electrode (3 mm diameter), a platinum wire counter electrode, and an Ag/AgCl (3 M KCl) reference electrode (all Metrohm., Switzerland). Scanning electron microscopy (SEM) images were obtained on a JSM-6700F (JEOL, Japan). Transmission electron microscopy (TEM) images were obtained using a JEM-2010 (JEOL, Japan).

2.3. Preparation of PtRu-MWCNT-Nafion Nanocomposite-Modified Glassy Carbon Electrodes

A 0.5 wt% Nafion solution was prepared by diluting 5 wt% Nafion solution with 0.1 M phosphate buffer solution (pH 7). A 10 mg MWCNTs were added to l mL 0.5 wt% Nafion solution with the aid of ultrasonic agitation for 1 hour to form a homogeneous MWCNT-Nafion solution. The glassy carbon electrode was polished with 0.3 and 0.05 alumina slurry and was rinsed with deionized water before modification. The MWCNT-Nafion nanocomposite film-modified glassy carbon electrode was prepared by casting a 6 of MWCNT-Nafion solution onto the surface of a glassy carbon electrode and drying under room temperature in the air. The PtRu nanoparticles were electrodeposited within the MWCNT-Nafion nanocomposite in a 0.1 M phosphate buffer solution (pH 7) containing different concentrations of K₂PtCl₆ and RuCl₃ by cyclic voltammetry ranging from −1.0 to 0 V versus Ag/AgCl at a scan rate of 50 mV s⁻¹ for 7 cycles. The atomic compositions of the PtRu nanoparticles electrodeposited in MWCNT-Nafion nanocomposite were analyzed by an energy-dispersive X-ray spectrometer. The content of PtRu in the MWCNT-Nafion nanocomposite was ca. 14 wt% which was determined by thermogravimetric analysis (not shown).

3. Results and Discussion

3.1. Characterization of PtRu nanoparticles with SEM, TEM, and Energy-Dispersive X-Ray Spectroscopy (EDS)

The electrodeposition of PtRu nanoparticles in MWCNT-Nafion nanocomposite was investigated by SEM and TEM and EDS was used to confirm the PtRu composition of the deposits. Figure 1 shows the SEM images of MWCNT-Nafion nanocomposite before and after electrodeposition of PtRu nanoparticles. The MWCNTs were well dispersed in the MWCNT-Nafion matrix that can be seen in Figure 1(a). This means that Nafion is a suitable medium for the dispersion of MWCNTs and MWCNTs act as high conductivity nanowires throughout the MWCNT-Nafion nanocomposite. The electrodeposited PtRu nanoparticles were observed on the surface of MWCNTs (see Figure 1(b)). Further information of the PtRu nanoparticles on the surface of MWCNTs was investigated by TEM. Figure 2 shows the typical TEM images of MWCNT-Nafion nanocomposite before and after electrodeposition of the PtRu nanoparticles. In Figure 2(b), it can be seen that PtRu nanoparticles were deposited in the MWCNT-Nafion nanocomposite with a diameter of 10–20 nm. The formation of PtRu nanoparticles within the MWCNT-Nafion nanocomposite is supported by EDS observation. Figure 3 shows the EDS patterns of MWCNT-Nafion nanocomposite before and after electrodeposition of PtRu nanoparticles. Figure 3(a) indicates that the C, O, and F were the major elements before electrodeposition. The C signal came from the MWCNTs and Nafion; O and F were derived from Nafion. In Figure 3(b), the Pt and Ru elements can be seen after the electrodeposition of PtRu nanoparticles. Thus, we can conclude that the PtRu nanoparticles are indeed coelectrodeposited in the MWCNT-Nafion nanocomposite.

(a)

(b)

(a)

(b)

(a)

(b)

3.2. Effect of the Atomic Ratio of Pt : Ru on the Electrocatalytic Ability towards the Methanol Electrooxidation

In order to investigate the effect of the atomic composition of PtRu on the electrocatalytic ability towards the electrochemical oxidation of methanol, the PtRu-MWCNT-Nafion nanocomposite-modified glassy carbon electrodes prepared with different atomic ratio of were characterized by cyclic voltammetry in 2 M CH₃OH + 1 M H₂SO₄. Figure 4 shows the cyclic voltammograms recorded for the Pt-MWCNT-Nafion (Figure 4(a)), PtRu()-MWCNT-Nafion (Figure 4(b)), PtRu()-MWCNT-Nafion (Figure 4(c)), and PtRu()-MWCNT-Nafion (Figure 4(d)) nanocomposite-modified glassy carbon electrodes in 2 M CH₃OH + 1 M H₂SO₄ at a scan rate of 50 mV s⁻¹ at cycle 5. Two peaks of methanol oxidation could be observed at Pt-MWCNT-Nafion-modified glassy carbon electrode (Figure 4(a)). The peak potentials were 0.669 and 0.513 V for the forward and backward scans, respectively. The forward anodic peak represented that the methanol was oxidized to carbon dioxide, and the reverse anodic peak resulted from the accumulation of carbonaceous species [1]. It can be seen in Figure 4 that the PtRu-MWCNT-Nafion-modified electrode exhibited a substantial negative shift of the forward anodic peak when the atomic composition of PtRu is changed from pure Pt to PtRu binary catalyst. The electrocatalytic oxidation is evident from the forward anodic peak potentials of methanol which are 0.522 and 0.669 V for PtRu()-MWCNT-Nafion and Pt-MWCNT-Nafion-modified electrodes, respectively. Further evidence of electrocatalytic ability at PtRu-MWCNT-Nafion nanocomposite can be observed from the ratio of the forward anodic peak current () to the backward anodic peak current (). The value shows the catalyst tolerance to accumulation of carbonaceous species [15]. From Figure 4, the values are 2.02, 6.55, 447.06, and 52.37 for the Pt-MWCNT-Nafion, PtRu()-MWCNT-Nafion, PtRu()-MWCNT-Nafion, and PtRu()-MWCNT-Nafion nanocomposite-modified glassy carbon electrodes, respectively. High value obtained at PtRu()-MWCNT-Nafion-modified glassy carbon electrode indicated that most of the intermediate carbonaceous species were oxidized to carbon dioxide in the forward scan at the PtRu()-MWCNT-Nafion-modified glassy carbon electrode. The optimal atomic ratio of PtRu() obtained in this study for direct methanol fuel cell is close to the previous report [2]. The improvement of methanol electrooxidation at the PtRu()-MWCNT-Nafion-modified electrode is attributed to the oxygenated species provided by Ru in the vicinity of Pt sites, which create additional active sites for oxidation [25].

3.3. Electrochemical Impedance Spectroscopy Studies of the PtRu-MWCNT-Nafion Nanocomposite-Modified Glassy Carbon Electrode

Electrochemical impedance spectroscopy was employed to investigate the methanol electrooxidation at PtRu-MWCNT-Nafion-modified glassy carbon electrode because it is a powerful technique to study the interface processes of modified electrodes. For comparison, a control experiment at the Pt-MWCNT-Nafion nanocomposite-modified glassy carbon electrode was also carried out. Figure 5 shows the Nyquist plots of Pt-MWCNT-Nafion and PtRu()-MWCNT-Nafion nanocomposite-modified glassy carbon electrodes in 2 M CH₃OH + 1 M H₂SO₄ solution at a working potential of 0.6 V. The ac impedance spectrum was recorded in the frequency range 0.01–10000 Hz. Figure 6 shows the equivalent circuits used to simulate the impedance response. In Figure 6, represents the solution resistance, the charge transfer resistance associated with methanol electrooxidation, and CPE the constant phase element associated with the double layer capacitance [15]. In Figure 5, the real axis intercept at high frequency was found to be independent of electrodes and corresponds to the uncompensated resistance of the bulk electrolyte solution (). The which controls the electron transfer kinetics of electroactive species at the electrode interface can be estimated from the diameter of the semicircle at higher frequencies. The of the PtRu()-MWCNT-Nafion-modified glassy carbon electrode (3.72 ) was smaller than that of Pt-MWCNT-Nafion-modified glassy carbon electrode (11.4 ), indicating that the higher electrocatalytic activity towards the methanol electrooxidation was obtained at PtRu()-MWCNT-Nafion-modified glassy carbon electrode. This result is in accordance with the voltammetric responses of Figure 4.

3.4. Stability of the PtRu-MWCNT-Nafion Nanocomposite-Modified Glassy Carbon Electrode

The stability of the electrocatalyst towards the methanol electrooxidation is crucial for practical applications. To investigate the stability of the PtRu()-MWCNT-Nafion and Pt-MWCNT-Nafion nanocomposite-modified electrodes to methanol electrooxidation, chronoamperometry was performed. Figure 7 shows the chronoamperometry curves for the PtRu()-MWCNT-Nafion and Pt-MWCNT-Nafion nanocomposite-modified glassy carbon electrodes in 2 M CH₃OH + 1 M H₂SO₄ at an applied potential of 0.6 V. The current responses decreased sharply in the initial period of time at both the PtRu()-MWCNT-Nafion and Pt-MWCNT-Nafion nanocomposite-modified electrodes. This might be attributed to the formation of intermediate species such as during the methanol electrooxidation at the electrodes. The current response was higher at PtRu()-MWCNT-Nafion nanocomposite-modified electrode than that of Pt-MWCNT-Nafion nanocomposite-modified electrode after 3600 seconds. This indicates that the inclusion of Ru in PtRu-MWCNT-Nafion nanocomposite is able to alleviate surface passivation during the electrochemical oxidation of methanol. The higher electrocatalytic activity observed at PtRu()-MWCNT-Nafion nanocomposite-modified electrode is ascribed to that the Ru promotes the oxidation of the strongly bound on Pt by supplying an oxygen source in the form of .

4. Conclusion

In this work we have demonstrated that PtRu nanoparticles with a diameter of 10–20 nm can be deposited in MWCNT-Nafion nanocomposite by an electroreduction method. It indicates that MWCNTs are good candidates for catalyst support because of their high surface-to-volume ratio. The resulting PtRu-MWCNT-Nafion nanocomposite is active for the electrochemical oxidation of methanol, which is oxidized at a lower potential than that of Pt-MWCNT-Nafion nanocomposite. The PtRu()-MWCNT-Nafion nanocomposites show a higher value and a better stability than that of Pt-MWCNT-Nafion nanocomposites. This might be attributed to the bifunctional mechanism of Ru to Pt. It should be emphasized that the catalysts amount in the MWCNT-Nafion nanocomposite is also important for the preparation of methanol electrooxidation catalysts. The results presented in this paper demonstrate that the coelectrodeposition of PtRu in MWCNT-Nafion nanocomposite has a promising potential application in preparing bimetallic electrocatalysts for the development of direct methanol fuel cell.

Acknowledgments

The authors wish to thank the National Science Council, Taiwan, for financial support. This work is supported in part by the Ministry of Education, Taiwan, under the ATU plan.

References

A. S. Aricò, S. Srinivasan, and V. Antonucci, “DMFCs: from fundamental aspects to technology development,” Fuel Cells, vol. 1, no. 2, pp. 133–161, 2001.
View at: Google Scholar
Z. Liu, X. Y. Ling, X. Su, and J. Y. Lee, “Carbon-supported Pt and PtRu nanoparticles as catalysts for a direct methanol fuel cell,” The Journal of Physical Chemistry B, vol. 108, no. 24, pp. 8234–8240, 2004.
View at: Publisher Site | Google Scholar
M. J. González, C. H. Peters, and M. S. Wrighton, “Pt-Sn microfabricated surfaces as catalysts for organic electro-oxidation,” The Journal of Physical Chemistry B, vol. 105, no. 23, pp. 5470–5476, 2001.
View at: Publisher Site | Google Scholar
J. T. Moore, D. Chu, R. Jiang, G. A. Deluga, and C. M. Lukehart, “Synthesis and characterization of Os and Pt-Os/carbon nanocomposites and their relative performance as methanol electrooxidation catalysts,” Chemistry of Materials, vol. 15, no. 5, pp. 1119–1124, 2003.
View at: Publisher Site | Google Scholar
F. Liu, J. Y. Lee, and W. Zhou, “Template preparation of multisegment PtNi nanorods as methanol electro-oxidation catalysts with adjustable bimetallic pair sites,” The Journal of Physical Chemistry B, vol. 108, no. 46, pp. 17959–17963, 2004.
View at: Publisher Site | Google Scholar
K.-Y. Chan, J. Ding, J. Ren, S. Cheng, and K. Y. Tsang, “Supported mixed metal nanoparticles as electrocatalysts in low temperature fuel cells,” Journal of Materials Chemistry, vol. 14, no. 4, pp. 505–516, 2004.
View at: Google Scholar
D. M. Dotzauer, J. Dai, L. Sun, and M. L. Bruening, “Catalytic membranes prepared using layer-by-layer adsorption of polyelectrolyte/metal nanoparticle films in porous supports,” Nano Letters, vol. 6, no. 10, pp. 2268–2272, 2006.
View at: Publisher Site | Google Scholar
D. Cao and S. H. Bergens, “Pt- ${Ru}_{adatom}$ nanoparticles as anode catalysts for direct methanol fuel cells,” Journal of Power Sources, vol. 134, no. 2, pp. 170–180, 2004.
View at: Publisher Site | Google Scholar
K.-W. Park, D.-S. Han, and Y.-E. Sung, “PtRh alloy nanoparticle electrocatalysts for oxygen reduction for use in direct methanol fuel cells,” Journal of Power Sources, vol. 163, no. 1, pp. 82–86, 2006.
View at: Publisher Site | Google Scholar
Y. Liu, J. Chen, W. Zhang et al., “Nano-Pt modified aligned carbon nanotube arrays are efficient, robust, high surface area electrocatalysts,” Chemistry of Materials, vol. 20, no. 8, pp. 2603–2605, 2008.
View at: Publisher Site | Google Scholar
M. Chikae, K. Idegami, K. Kerman et al., “Direct fabrication of catalytic metal nanoparticles onto the surface of a screen-printed carbon electrode,” Electrochemistry Communications, vol. 8, no. 8, pp. 1375–1380, 2006.
View at: Publisher Site | Google Scholar
Z. Wang and K. Qiu, “Electrocatalytic oxidation of formic acid on platinum nanoparticle electrode deposited on the nichrome substrate,” Electrochemistry Communications, vol. 8, no. 7, pp. 1075–1081, 2006.
View at: Publisher Site | Google Scholar
B. Yang, Q. Lu, Y. Wang et al., “Simple and low-cost preparation method for highly dispersed PtRu/C catalysts,” Chemistry of Materials, vol. 15, no. 18, pp. 3552–3557, 2003.
View at: Publisher Site | Google Scholar
T. J. Schmidt, M. Noeske, H. A. Gasteiger, R. J. Behm, P. Britz, and H. Bönnemann, “PtRu alloy colloids as precursors for fuel cell catalysts: a combined XPS, AFM, HRTEM, and RDE study,” Journal of the Electrochemical Society, vol. 145, no. 3, pp. 925–931, 1998.
View at: Google Scholar
Y. Lin, X. Cui, C. H. Yen, and C. M. Wai, “PtRu/carbon nanotube nanocomposite synthesized in supercritical fluid: a novel electrocatalyst for direct methanol fuel cells,” Langmuir, vol. 21, no. 24, pp. 11474–11479, 2005.
View at: Publisher Site | Google Scholar
M. Mastragostino, A. Missiroli, and F. Soavi, “Carbon supports for electrodeposited Pt-Ru catalysts for DMFCs,” Journal of the Electrochemical Society, vol. 151, no. 11, pp. A1919–A1924, 2004.
View at: Publisher Site | Google Scholar
G. G. Wildgoose, C. E. Banks, and R. G. Compton, “Metal nanoparticles and related materials supported on carbon nanotubes: methods and applications,” Small, vol. 2, no. 2, pp. 182–193, 2006.
View at: Publisher Site | Google Scholar
M. Carmo, V. A. Paganin, J. M. Rosolen, and E. R. Gonzalez, “Alternative supports for the preparation of catalysts for low-temperature fuel cells: the use of carbon nanotubes,” Journal of Power Sources, vol. 142, no. 1-2, pp. 169–176, 2005.
View at: Publisher Site | Google Scholar
M. Okamoto, T. Fujigaya, and N. Nakashima, “Design of an assembly of poly(benzimidazole), carbon nanotubes, and Pt nanoparticles for a fuel-cell electrocatalyst with an ideal interfacial nanostructure,” Small, vol. 5, no. 6, pp. 735–740, 2009.
View at: Publisher Site | Google Scholar
X. Wang, W. Li, Z. Chen, M. Waje, and Y. Yan, “Durability investigation of carbon nanotube as catalyst support for proton exchange membrane fuel cell,” Journal of Power Sources, vol. 158, no. 1, pp. 154–159, 2006.
View at: Publisher Site | Google Scholar
R. P. Deo and J. Wang, “Electrochemical detection of carbohydrates at carbon-nanotube modified glassy-carbon electrodes,” Electrochemistry Communications, vol. 6, no. 3, pp. 284–287, 2004.
View at: Publisher Site | Google Scholar
Y.-C. Tsai, J.-M. Chen, S.-C. Li, and F. Marken, “Electroanalytical thin film electrodes based on a ${Nafion}^{TM}$ —multi-walled carbon nanotube composite,” Electrochemistry Communications, vol. 6, no. 9, pp. 917–922, 2004.
View at: Publisher Site | Google Scholar
H.-W. Liaw, J.-M. Chen, and Y.-C. Tsai, “Development of an amperometric ethanol biosensor based on a multiwalled carbon nanotube-Nafion-alcohol dehydrogenase nanobiocomposite,” Journal of Nanoscience and Nanotechnology, vol. 6, no. 8, pp. 2396–2402, 2006.
View at: Publisher Site | Google Scholar
Y. Cheng, Y. Liu, J. Huang et al., “Rapid amperometric detection of coliforms based on MWNTs/Nafion composite film modified glass carbon electrode,” Talanta, vol. 75, no. 1, pp. 167–171, 2008.
View at: Publisher Site | Google Scholar
D. R. Rolison, P. L. Hagans, K. E. Swider, and J. W. Long, “Role of hydrous ruthenium oxide in Pt-Ru direct methanol fuel cell anode electrocatalysts: the importance of mixed electron/proton conductivity,” Langmuir, vol. 15, no. 3, pp. 774–779, 1999.
View at: Google Scholar

Copyright

Copyright © 2009 Yu-Huei Hong and Yu-Chen Tsai. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

2163

Downloads

1155

Citations