Facile Preparation of TiO<sub>2</sub> Nanobranch/Nanoparticle Hybrid Architecture with Enhanced Light Harvesting Properties for Dye-Sensitized Solar Cells

Kim, Ju Seong; Shin, Seong Sik; Han, Hyun Soo; Shin, Sun; Suk, Jae Ho; Kang, Kisuk; Hong, Kug Sun; Cho, In Sun

doi:https://doi.org/10.1155/2015/139715

Journal of Nanomaterials

On this page

Abstract Introduction Experimental Results and Discussion Conclusions Supplementary Materials References Copyright Related Articles

Special Issue

Nanomaterials for Solar Energy Harvesting and Storage

View this Special Issue

Research Article | Open Access

Volume 2015 | Article ID 139715 | https://doi.org/10.1155/2015/139715

Facile Preparation of TiO₂ Nanobranch/Nanoparticle Hybrid Architecture with Enhanced Light Harvesting Properties for Dye-Sensitized Solar Cells

Ju Seong Kim,¹Seong Sik Shin,¹Hyun Soo Han,²Sun Shin,¹Jae Ho Suk,¹Kisuk Kang,¹Kug Sun Hong,¹and In Sun Cho³

Academic Editor: Chen Jiangchao

Received06 Jan 2015

Accepted11 Mar 2015

Published26 Oct 2015

Abstract

We report TiO₂ nanobranches/nanoparticles (NBN) hybrid architectures that can be synthesized by a facile solution phase method. The hybrid architecture simultaneously improves light harvesting and charge collection performances for a dye-sensitized solar cell. First, TiO₂ nanorods with a trunk length of 2 μm were grown on a fluorine-doped tin oxide (FTO)/glass substrate, and then nanobranches and nanoparticles were deposited on the nanorods’ trunks through a solution method using an aqueous TiCl₃ solution at 80°C. The relative amount of nanobranches and nanoparticles can be controlled by multiplying the number of TiCl₃ treatments to maximize the amount of surface area. We found that the resultant TiO₂ NBN hybrid architecture greatly improves the amount of dye adsorption (five times compared to bare nanorods) due to the enhanced surface area, while maintaining a fast charge collection, leading to a three times higher current density and thus tripling the maximum power conversion efficiency for a dye-sensitized solar cell.

1. Introduction

Dye-sensitized solar cells (DSSCs) have attracted attention as one of the most promising solar conversion devices due to their low fabrication cost and high conversion efficiency [1–4]. In general, a DSSC consists of four parts: the sensitizer (dye molecule), a semiconductor for electron transport, a redox electrolyte, and charge collecting electrodes. Typically, nanoparticle-based photoanodes using n-type semiconductors (TiO₂, ZnO, SnO₂, BaSnO₃, Zn₂SnO₄, etc.) have been investigated for adsorption of dye molecules as a result of their large surface areas [4–10]. However, these nanoparticle-based photoanodes limit charge collection efficiency because they have a large number of transport-limiting trapping/detrapping events on the nanoparticle surface; that is, they show a low charge collection efficiency [11, 12].

One strategy for overcoming this low charge collection efficiency is the use of vertically aligned one-dimensional (1D) nanostructures, which offer a direct electron transport pathway to the electrode, thus enabling low charge recombination. To date, various 1D nanostructured photoanodes have been studied, including nanowires (NWs), nanotubes (NTs), nanoparticle-decorated NWs, dendritic NWs, and core/shell NWs [13–19]. For instance, single-crystal TiO₂ nanowires were found to have a large electron diffusion coefficient compared to TiO₂ nanoparticles, owing to a lower density of surface defects [14]. Additionally, a preferentially oriented anatase TiO₂ nanotube, which has a small quantity of high angle grain boundaries, shows a large electron diffusion coefficient and diffusion length compared to TiO₂ nanoparticles [17]. Moreover, dendritic ZnO NWs with multiple branches demonstrated an enhanced photocurrent and internal quantum efficiency over nanoparticle-based cells [19]. Nevertheless, these 1D nanostructured photoanodes frequently display a low light harvesting efficiency due to a lower dye loading capacity, which leads to a low photocurrent density compared to nanoparticle-based DSSCs [14]. Recently, to address this low dye loading problem in 1D nanostructures, a few studies have adopted hierarchical structures based on the 1D nanostructures (e.g., nanoforests and branched arrays) [20–23]. Even though the hierarchical structures exhibit improved charge collection and light harvesting efficiencies, their preparation methods are somewhat complex and require vacuum equipment, making it difficult to reproduce the synthesis technique and prepare large scale devices.

Here, we report a facile solution phase method to synthesize a TiO₂ nanostructured photoanode consisting of nanobranches/nanoparticles on the trunks of the NWs. These hybrid NWs can be synthesized simply by using an aqueous TiCl₃ solution at low temperature (80°C). One advantage of our method is that it enables us to control the relative amount of nanobranches and nanoparticles on the TiO₂ NW trunks as a result of applying multiple TiCl₃ treatments, to maximize dye adsorption (i.e., the light harvesting property). Additionally, this method facilitates a scalable preparation (up to a 4-inch wafer) due to it being a low temperature process. We carefully investigated the effect of the TiCl₃ treatment on the morphology progress and dye adsorption capacity, and we demonstrate that the hybrid architecture improves the photocurrent and incident photon-to-current conversion efficiency (IPCE) for DSSCs by a factor of two compared to nanorod-based DSSCs.

2. Experimental

2.1. Preparation of the TiO₂ Nanowires (NWs)

Rutile TiO₂ NWs were synthesized on a fluorine-doped tin oxide (FTO)/glass substrate by a hydrothermal method [24]. Before growing the TiO₂ nanorods, a TiO₂ seed layer was deposited by a spin coating method using a TiO₂ polymeric sol [25] and then annealed at 450°C for 1 h. Titanium butoxide (97%, Aldrich) was slowly added to 50 mL of a hydrochloric acid (HCl) aqueous solution (25 mL of deionized (DI) water + 25 mL concentrated HCl solution (38%)) and stirred for 30 min to obtain a transparent solution. This precursor solution was transferred into a sealed Teflon-lined stainless steel autoclave (100 mL volume) and then the TiO₂ seed layer-coated FTO/glass substrates were immersed in this solution. The autoclave was placed in an electric oven and heated to 170°C for 6 h without stirring. The resultant TiO₂ nanorod samples were washed with DI water several times and finally annealed at 450°C for 1 h in air.

2.2. TiCl₃ Treatment

To grow the nanobranches and nanoparticles, the TiO₂ nanorod samples were immersed into a solution containing 10 mL of DI water, 0.1 mL of concentrated HCl solution, and 1 mL of TiCl₃ solution (Aldrich, 10 wt.% in 20–30 wt.% HCl solution) and held at 80°C for 30 min in an oven. The effect of the TiCl₃ treatment time (30 min, 1 h, 2 h, and 4 h) on the morphology was examined first. The relative quantity of nanobranches/nanoparticles was controlled by repeating the TiCl₃ treatment. We have labeled the sample names as 30 min-1, 30 min-2, 30 min-3, and 30 min-4 to correspond to the number of additional TiCl₃ treatments. Afterward, all samples were washed with DI water and annealed at 450°C for 1 h in air.

2.3. Fabrication of DSSCs

The annealed samples were soaked in a ruthenium dye solution (N719, ruthenium (2,2′bipyridyl-4,4′dicarboxylate)₂(NCS)₂) at room temperature for 12 h. Platinum-coated FTO substrates prepared by sputtering were used as the counter electrodes. The sandwich-type DSSCs were assembled using the samples as the photoanodes and the Pt-coated FTO glasses as the counter electrodes with a hot-melt film (~60 μm, Surlyn, DuPont) as a spacer. Finally, the electrolyte was an iodide-based liquid electrolyte (SI16 L1535-01, Merck), which was introduced into the cell through a hole in the counter electrode. The active area of all samples was 0.25 cm².

2.4. Material and DSSC Characterization

The crystal structure and phase of the synthesized samples were identified by an X-ray diffractometer (XRD, Bruker, New D8 Advance) with CuKα radiation operated at 40 kV and 40 mA. The morphologies of the prepared samples were observed by a field-emission scanning electron microscope (FESEM, Hitachi, SU70) and a high-resolution transmission electron microscope (HRTEM, JEOL, JEM-3000F). The photovoltaic performance and electron impedance spectroscopy (EIS) of the DSSCs were measured with a potentiostat (CH Instruments, CHI308C) under AM 1.5G simulated solar light (100 mW/cm², Sol3A, Newport). The ultraviolet-visible (UV-Vis) absorption spectra of the dye solutions, collected by desorption from the samples, were investigated with an UV-Vis spectrometer (Agilent Technologies, Cary 5000). The DSSCs’ electron transport properties were characterized by intensity-modulated photovoltage spectroscopy (IMVS) using an electrochemical workstation (Zennium, Zahner) with an attached frequency analyzer and a light-emitting diode (667 nm).

3. Results and Discussion

The morphology of the TiO₂ nanorods (NRs) used as the stem for the TiO₂ hybrid architecture is shown in Figures S1 and S2 (in Supplementary Material available online at http://dx.doi.org/10.1155/2015/139715). The NRs are grown on the FTO/glass substrate by a hydrothermal method [26]. The NRs have an average diameter of the length of nm and μm (Tables S1 and S2), presenting high crystallinity with a preferred growth direction of [001]. Figure 1 shows top-view FESEM images of the TiO₂ hybrid architectures’ microscopic morphologies, prepared by repeating the TiCl₃ treatment (1–4 times) at 80°C for 30 min. It can be seen that the TiCl₃ treatment significantly affects the morphology of the TiO₂ NRs. After the first TiCl₃ treatment (sample 30 min-1), small nanobranches (~10 nm in diameter and ~60 nm in length) were formed on the surface of the individual TiO₂ NRs (Figure 1(a)), which lengthen further (~100 nm long) with an increased density on the NR surface after the second TiCl₃ treatment (sample 30 min-2, Figure 1(b)). When the treatment was repeated three times (sample 30 min-3, Figure 1(c)), the length of the nanobranches increased to 200–300 nm, reducing the interspaces between the TiO₂ NRs; these interspaces decreased significantly after the fourth treatment (sample 30 min-4, Figure 1(d)). We also investigated the effects of the TiCl₃ treatment duration time (Figure S3). An increased duration time provides a similar effect on the morphology; that is, it lengthens the nanobranches and increases their density as the duration time was increased from 30 min to 4 h.

(a)

(b)

(c)

(d)

The detailed variation in the TiO₂ nanostructure morphology with multiple TiCl₃ treatments was investigated further by utilizing cross-sectional FESEM images (Figure 2). For the 30 min-1 and 30 min-2 samples, there were no significant changes in the TiO₂ NRs except for the formation of nanobranches. However, for the 30 min-3 sample, the nanobranches grew in length, reducing the space between NRs, especially at their tops (Figure 2(c)). Interestingly, at the bottom of the nanorods, nanoparticles with an average size of ~30 nm formed together with the nanobranches, suggesting that more than three TiCl₃ treatments induce a different growth mode, generating nanoparticles at the bottom of the NRs. Finally, after the fourth treatment (30 min-4), the TiO₂ nanoparticles completely filled the NR interspaces, up to the top of the film. These two different growth modes, that is, the nanobranch and nanoparticle growth, during the multiple TiCl₃ treatments enable the morphology to be tuned, thereby controlling the relative surface area of the 1D nanostructure based on the NRs.

(a)

(b)

(c)

(d)

The XRD patterns of the samples discussed above are shown in Figure 3. All diffraction peaks of the TiO₂ NRs (30 min-1) are in agreement with tetragonal rutile TiO₂ (JCPDS number 21-1276, P4₂/mnm, Ǻ, Ǻ). In general, rutile TiO₂ NRs prepared by a hydrothermal method grow along the (001) plane, as it has the fastest growth rate compared to the other crystal faces [13, 27, 28]. Similar to other reports, our TiO₂ NRs have a preferred growth direction of [], which was also confirmed by a TEM analysis (Figure S2). For the XRD peaks of the multiple TiCl₃ treatment samples, there were no considerable differences from the 30 min-1 sample, suggesting that the nanobranches and nanoparticles are also rutile tetragonal structures. The perceptible development of the (110) diffraction peaks at 27.5° in the 30 min-2, 30 min-3, and 30 min-4 samples implies that the nanobranches have the same preferred [001] growth direction [24].

Based on the above observation, the formation process of the TiO₂ nanobranch/nanoparticle (NBN) hybrid architectures is displayed schematically in Figure 4. After the first treatment, short nanobranches are formed on the surface of the NRs, which grow to longer nanobranches with an average length of ~100 nm after the second TiCl₃ treatment. The third TiCl₃ treatment induces nanoparticle growth from the bottom of the film, which reduces the interspaces between the NRs at their bases. With a further TiCl₃ treatment, however, additional nanoparticles formed, filling the remaining interspaces between the NRs to the top of the film, finally forming a NBN hybrid architecture. It should be noted that these interesting 1D architectures are obtained by simply repeating the TiCl₃ treatment, which enabled the unusual growth (or deposition) behavior during the additional TiCl₃ treatments. In general, the pH of the growth solution significantly affects the growth morphology (i.e., the crystal phase and morphology) of TiO₂ nanocrystals [29], that is, nanoparticles near pH 7 and elongated nanorods or nanoneedles below pH 4. Therefore, the two different growth modes, of the nanobranches and nanoparticles, might relate to the change in the solution’s pH value during the multiple TiCl₃ treatments. A detailed analysis of this is under investigation.

Next, in order to check the usefulness of the NBN hybrid architectures for a solar energy conversion device, we fabricated dye-sensitized solar cells (DSSCs) with them. First, the light harvesting behavior, that is, the dye adsorption property, was investigated by UV/Vis absorption spectroscopy (Figure 5). The absorption spectra were obtained of dye solutions after collecting the dye by a desorption process in a basic solution. The peak at 510 nm in the absorption spectra is a characteristic peak of these dye molecules (N719), and this can be used to estimate the amount of dye molecules adsorbed onto the TiO₂ surface. As shown in the inset of Figure 5, the amount of adsorbed dye molecules continued to increase with repeated TiCl₃ treatments, before becoming saturated with the 30 min-3 sample. The amount of adsorbed dye of the 30 min-4 sample increased nearly by a factor of four compared to the 30 min-0 sample, indicating that the NBN hybrid architecture (30 min-4 sample) has a larger surface area, thus improving the light harvesting efficiency for the DSSCs.

Figure 6(a) shows the photocurrent density-voltage curves of the DSSCs fabricated using the above four samples, which were measured under AM 1.5G simulated solar light (1 sun, 100 mW/cm²) and their representative solar cell parameters are shown in Figures 6(b) and 6(c) (with the other parameters summarized in Table 1). Initially, the short circuit photocurrent density () values increased linearly until the third treatment and eventually reaching a maximum value of 13.4 mA/cm² for the fourth treatment. This result strongly correlates with the absorbance spectra of the desorbed dye shown in the inset of Figure 5, indicating that the NBN hybrid architecture has an improved light harvesting property, thus increasing the for DSSCs. The open circuit voltage () of the TiO₂ NR-based DSSC was 0.82 V. This value decreased slightly with an increasing number of TiCl₃ treatments to 0.77, 0.72, 0.71, and 0.69 V for the 30 min-1, 30 min-2, 30 min-3, and 30 min-4 samples, respectively. In the case of the fill factor (FF) values, there were no notable differences (Table 1). As a result, the power conversion efficiency was enhanced from 2.6% (for the NR-based DSSC) to 5.3% (for the NBN hybrid architecture- (30 min-4-) based DSSC), demonstrating that the NBN hybrid architecture is advantageous to improve in DSSCs.

(a)

(b)

(c)

To understand the effect of the multiple TiCl₃ treatments on the electron dynamics, an intensity-modulated photocurrent/photovoltage spectroscopy (IMPS/IMVS) was used to measure the samples (Figure S4). All samples show a typical power-law dependence of their transport time constants on the value (Figure S4a). This indicates an exclusive random walk of photoelectrons between trap sites having a power-law distribution of waiting (release) times in the form of , where the parameter can be related to the shape of the trap distribution [30, 31]. Initially, the charge transport time increased with the additional TiCl₃ treatments, indicating that the route photoelectrons travel to the FTO substrate became longer and more complicated due to the nanobranches and nanoparticles. This reduction in the transport time constant competes with the effect of the increased dye adsorption. The transport time constant and the dye adsorption correlate to the charge collection efficiency and light harvesting efficiency, respectively, which determine the power conversion efficiency. However, since the effects of the dye adsorption are dominant, the power conversion efficiency of the TiO₂ NBN hybrid architecture DSSC increased with repeated TiCl₃ treatments.

Second, the charge recombination time constant consistently decreased with an increasing number of TiCl₃ treatments. The infiltrated TiO₂ nanobranches and nanoparticles decreased the diffusion efficiency of the ions in the electrolyte. The relation between the recombination time and can be described by the following equation [32, 33]:where is the molar gas constant, is the temperature, is the reaction order for the electrons, is the Faraday constant, is the electrode area, is the incident photon flux, is the concentration of accessible electronic states in the conduction band, and and are the kinetic constants of the injected electron with triiodide () back reaction and the recombination of these electrons with oxidized dye () molecules, respectively. Neglecting the recombination of the injected electrons with oxidized dye molecules, the value is logarithmically dependent on the back reaction of these electrons with the triiodide (). Therefore, the rate of the electron recombination from the TiO₂ photoanode to the ions in the electrolyte increased with an increasing number of TiCl₃ treatments.

Figure 7 shows the incident photon-to-current efficiency (IPCE) spectra of the TiO₂ photoanode-based DSSCs. All of the DSSCs show the typical spectral response of N719-based DSSCs with a peak at approximately 530 nm. However, the maximum IPCE (or external quantum efficiency, EQE) varies with the number of TiCl₃ treatments. The 30 min-4 sample exhibited the maximum IPCE and the NR sample displayed the minimum IPCE. The IPCE of DSSCs is determined by the light harvesting efficiency (), the charge injection efficiency (), and the charge collection efficiency (). The IPCE value can be expressed by the following equation: The light harvesting efficiency is generally affected by the dye loading capacity [34]. As mentioned in Figure 5, the dye loading capacity of the TiO₂ photoanodes increased significantly with multiple TiCl₃ treatments, implying that the light harvesting efficiency increased with additional TiCl₃ treatments. On the other hand, the IMPS and IMVS data (Figure S4) demonstrate that the charge collection efficiency decreased monotonically with the multiple TiCl₃ treatments. Even though the NBN hybrid architecture reduced the electron transport property slightly, it can be concluded that the enhancement seen in the light harvesting efficiency was greater than the decrease in the charge collection efficiency. Interestingly, the IPCE values of the samples after multiple TiCl₃ treatments show a shoulder at a longer wavelength (>680 nm), indicating that the NBN hybrid architecture has additional enhancement effects for DSSCs, that is, improving the light scattering effect. This light scattering effect also enhances the light harvesting efficiency in combination with the increased dye loading capacity.

4. Conclusions

In summary, we report on a TiO₂ hybrid architecture composed of TiO₂ nanobranches and nanoparticles, easily synthesized by a solution phase method. A TiCl₃ aqueous solution treatment at 80°C enables a controlled morphology of the TiO₂ nanorods. By repeating this TiCl₃ treatment, nanobranches and/or nanoparticles are deposited on the trunks of the TiO₂ nanorods, giving hybrid architecture with an enhanced surface area. We found that the resultant TiO₂ nanobranch/nanoparticle hybrid architecture greatly improved the dye adsorption (five times compared to bare nanorods) due to the enhanced surface area, albeit a slight decrease in a charge collection property. Additionally, the complex architecture produces a large light scattering effect, eventually leading to a three times greater current density and thus tripling the maximum power conversion efficiency for a dye-sensitized solar cell. We believe that the synthesized TiO₂ hybrid architecture, after further structural optimization, has the potential for use in other energy harvesting devices such as quantum-dot dye-sensitized solar cells (QD-DSSCs), photoelectrochemical (PEC) water-splitting, and solid-state solar cells, which require both high light harvesting and charge collection efficiencies.

Conflict of Interests

The authors declare that there is no conflict of interests regarding the publication of this paper.

Acknowledgment

This work was partially supported by the new faculty research fund of Ajou University (S-2014-G0001-00309).

Supplementary Materials

The supplementary material shows additional electron microscopy images (SEM and TEM) and electrochemical characterizations of nanobranches/nanoparticles hybrid TiO₂ architectures

Supplementary Material

References

M. Grätzel, “Dye-sensitized solar cells,” Journal of Photochemistry and Photobiology C: Photochemistry Reviews, vol. 4, no. 2, pp. 145–153, 2003.
View at: Publisher Site | Google Scholar
B. O'Regan and M. Graetzel, “A low-cost, high-efficiency solar cell based on dye-sensitized colloidal TiO₂ films,” Nature, vol. 353, no. 6346, pp. 737–740, 1991.
View at: Publisher Site | Google Scholar
M. Grätzel, “Solar energy conversion by dye-sensitized photovoltaic cells,” Inorganic Chemistry, vol. 44, no. 20, pp. 6841–6851, 2005.
View at: Publisher Site | Google Scholar
A. Yella, H.-W. Lee, H. N. Tsao et al., “Porphyrin-sensitized solar cells with cobalt (II/III)-based redox electrolyte exceed 12 percent efficiency,” Science, vol. 334, no. 6056, pp. 629–634, 2011.
View at: Publisher Site | Google Scholar
T. P. Chou, Q. Zhang, G. E. Fryxell, and G. Cao, “Hierarchically structured ZnO film for dye-sensitized solar cells with enhanced energy conversion efficiency,” Advanced Materials, vol. 19, no. 18, pp. 2588–2592, 2007.
View at: Publisher Site | Google Scholar
Q. Zhang, T. P. Chou, B. Russo, S. A. Jenekhe, and G. Cao, “Aggregation of ZnO nanocrystallites for high conversion efficiency in dye-sensitized solar cells,” Angewandte Chemie, vol. 120, no. 13, pp. 2436–2440, 2008.
View at: Google Scholar
J. Liu, T. Luo, S. Mouli T, F. Meng, B. Sun, and M. Li, “A novel coral-like porous SnO₂ hollow architecture: biomimetic swallowing growth mechanism and enhanced photovoltaic property for dye-sensitized solar cell application,” Chemical Communications, vol. 46, no. 3, pp. 472–474, 2010.
View at: Publisher Site | Google Scholar
A. Kay and M. Grätzel, “Dye-sensitized core-shell nanocrystals: Improved efficiency of mesoporous tin oxide electrodes coated with a thin layer of an insulating oxide,” Chemistry of Materials, vol. 14, no. 7, pp. 2930–2935, 2002.
View at: Publisher Site | Google Scholar
S. S. Shin, J. S. Kim, J. H. Suk et al., “Improved quantum efficiency of highly efficient perovskite BaSnO₃-based dye-sensitized solar cells,” ACS Nano, vol. 7, no. 2, pp. 1027–1035, 2013.
View at: Publisher Site | Google Scholar
D. W. Kim, S. S. Shin, I. S. Cho et al., “Synthesis and photovoltaic property of fine and uniform Zn₂SnO₄ nanoparticles,” Nanoscale, vol. 4, no. 2, pp. 557–562, 2012.
View at: Publisher Site | Google Scholar
J. H. Noh, H. S. Han, S. Lee et al., “Nanowire-based three-dimensional transparent conducting oxide electrodes for extremely fast charge collection,” Advanced Energy Materials, vol. 1, no. 5, pp. 829–835, 2011.
View at: Publisher Site | Google Scholar
W.-Q. Wu, J.-Y. Liao, H.-Y. Chen, X.-Y. Yu, C.-Y. Su, and D.-B. Kuang, “Dye-sensitized solar cells based on a double layered TiO₂ photoanode consisting of hierarchical nanowire arrays and nanoparticles with greatly improved photovoltaic performance,” Journal of Materials Chemistry, vol. 22, no. 34, pp. 18057–18062, 2012.
View at: Publisher Site | Google Scholar
B. Liu and E. S. Aydil, “Growth of oriented single-crystalline rutile TiO₂ nanorods on transparent conducting substrates for dye-sensitized solar cells,” Journal of the American Chemical Society, vol. 131, no. 11, pp. 3985–3990, 2009.
View at: Publisher Site | Google Scholar
X. Feng, K. Zhu, A. J. Frank, C. A. Grimes, and T. E. Mallouk, “Rapid charge transport in dye-sensitized solar cells made from vertically aligned single-crystal rutile TiO₂ nanowires,” Angewandte Chemie International Edition, vol. 51, no. 11, pp. 2727–2730, 2012.
View at: Publisher Site | Google Scholar
G. K. Mor, K. Shankar, M. Paulose, O. K. Varghese, and C. A. Grimes, “Use of highly-ordered TiO₂ nanotube arrays in dye-sensitized solar cells,” Nano Letters, vol. 6, no. 2, pp. 215–218, 2006.
View at: Publisher Site | Google Scholar
J. R. Jennings, A. Ghicov, L. M. Peter, P. Schmuki, and A. B. Walker, “Dye-sensitized solar cells based on oriented TiO₂ nanotube arrays: transport, trapping, and transfer of electrons,” Journal of the American Chemical Society, vol. 130, no. 40, pp. 13364–13372, 2008.
View at: Publisher Site | Google Scholar
S. Lee, I. J. Park, D. H. Kim et al., “Crystallographically preferred oriented TiO₂ nanotube arrays for efficient photovoltaic energy conversion,” Energy and Environmental Science, vol. 5, no. 7, pp. 7989–7995, 2012.
View at: Publisher Site | Google Scholar
M. Law, L. E. Greene, J. C. Johnson, R. Saykally, and P. Yang, “Nanowire dye-sensitized solar cells,” Nature Materials, vol. 4, no. 6, pp. 455–459, 2005.
View at: Publisher Site | Google Scholar
Y. Gao, M. Nagai, T.-C. Chang, and J.-J. Shyue, “Solution-derived ZnO nanowire array film as photoelectrode in dye-sensitized solar cells,” Crystal Growth and Design, vol. 7, no. 12, pp. 2467–2471, 2007.
View at: Publisher Site | Google Scholar
S. H. Ko, D. Lee, H. W. Kang et al., “Nanoforest of hydrothermally grown hierarchical ZnO nanowires for a high efficiency dye-sensitized solar cell,” Nano Letters, vol. 11, no. 2, pp. 666–671, 2011.
View at: Publisher Site | Google Scholar
H. Wang, Y. Bai, Q. Wu et al., “Rutile TiO₂ nano-branched arrays on FTO for dye-sensitized solar cells,” Physical Chemistry Chemical Physics, vol. 13, no. 15, pp. 7008–7013, 2011.
View at: Publisher Site | Google Scholar
W.-P. Liao and J.-J. Wu, “Wet chemical route to hierarchical TiO₂ nanodendrite/ nanoparticle composite anodes for dye-sensitized solar cells,” Journal of Materials Chemistry, vol. 21, no. 25, pp. 9255–9262, 2011.
View at: Publisher Site | Google Scholar
F. Shao, J. Sun, L. Gao, S. Yang, and J. Luo, “Forest-like TiO₂ hierarchical structures for efficient dye-sensitized solar cells,” Journal of Materials Chemistry, vol. 22, no. 14, pp. 6824–6830, 2012.
View at: Publisher Site | Google Scholar
I. S. Cho, Z. Chen, A. J. Forman et al., “Branched TiO₂ nanorods for photoelectrochemical hydrogen production,” Nano Letters, vol. 11, no. 11, pp. 4978–4984, 2011.
View at: Publisher Site | Google Scholar
H. S. Jung, J.-K. Lee, B. S. Kang, Q. Jia, and M. Nastasi, “Strain relaxation in sol-gel grown epitaxial anatase thin films,” The Journal of Physical Chemistry C, vol. 112, no. 11, pp. 4205–4208, 2008.
View at: Publisher Site | Google Scholar
E. Hosono, S. Fujihara, K. Kakiuchi, and H. Imai, “Growth of submicrometer-scale rectangular parallelepiped rutile TiO₂ films in aqueous TiCl₃ solutions under hydrothermal conditions,” Journal of the American Chemical Society, vol. 126, no. 25, pp. 7790–7791, 2004.
View at: Publisher Site | Google Scholar
H. Cheng, J. Ma, Z. Zhao, and L. Qi, “Hydrothermal preparation of uniform nanosize rutile and anatase particles,” Chemistry of Materials, vol. 7, no. 4, pp. 663–671, 1995.
View at: Publisher Site | Google Scholar
H. Perron, C. Domain, J. Roques, R. Drot, E. Simoni, and H. Catalette, “Optimisation of accurate rutile TiO₂ (110), (100), (101) and (001) surface models from periodic DFT calculations,” Theoretical Chemistry Accounts, vol. 117, no. 4, pp. 565–574, 2007.
View at: Publisher Site | Google Scholar
S. Lee, I.-S. Cho, J. H. Lee et al., “Two-step sol-gel method-based TiO₂ nanoparticles with uniform morphology and size for efficient photo-energy conversion devices,” Chemistry of Materials, vol. 22, no. 6, pp. 1958–1965, 2010.
View at: Publisher Site | Google Scholar
J. Nelson, S. A. Hague, D. R. Klug, and J. R. Durrant, “Trap-limited recombination in dye-sensitized nanocrystalline metal oxide electrodes,” Physical Review B, vol. 63, no. 20, Article ID 205321, 9 pages, 2001.
View at: Publisher Site | Google Scholar
J. van de Lagemaat and A. J. Frank, “Nonthermalized electron transport in dye-sensitized nanocrystalline TiO₂ films: transient photocurrent and random-walk modeling studies,” The Journal of Physical Chemistry B, vol. 105, no. 45, pp. 11194–11205, 2001.
View at: Publisher Site | Google Scholar
Q. Wang, J.-E. Moser, and M. Grätzel, “Electrochemical impedance spectroscopic analysis of dye-sensitized solar cells,” The Journal of Physical Chemistry B, vol. 109, no. 31, pp. 14945–14953, 2005.
View at: Publisher Site | Google Scholar
D. Hwang, D. Y. Kim, and S. Y. Jang, “Superior photoelectrodes for solid-state dye-sensitized solar cells using amphiphilic TiO₂,” Journal of Materials Chemistry A, vol. 1, no. 4, pp. 1228–1238, 2013.
View at: Publisher Site | Google Scholar
J.-H. Yum, S.-R. Jang, R. Humphry-Baker et al., “Effect of coadsorbent on the photovoltaic performance of zinc pthalocyanine-sensitized solar cells,” Langmuir, vol. 24, no. 10, pp. 5636–5640, 2008.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2015 Ju Seong Kim et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

1460

Downloads

1237

Citations

Journal of Nanomaterials

Nanomaterials for Solar Energy Harvesting and Storage

Facile Preparation of TiO2 Nanobranch/Nanoparticle Hybrid Architecture with Enhanced Light Harvesting Properties for Dye-Sensitized Solar Cells

Abstract

1. Introduction

2. Experimental

2.1. Preparation of the TiO2 Nanowires (NWs)

2.2. TiCl3 Treatment

2.3. Fabrication of DSSCs

2.4. Material and DSSC Characterization

3. Results and Discussion

4. Conclusions

Conflict of Interests

Acknowledgment

Supplementary Materials

References

Copyright

Facile Preparation of TiO₂ Nanobranch/Nanoparticle Hybrid Architecture with Enhanced Light Harvesting Properties for Dye-Sensitized Solar Cells

2.1. Preparation of the TiO₂ Nanowires (NWs)

2.2. TiCl₃ Treatment