Tunable SnO<sub>2</sub> Nanoribbon by Electric Fields and Hydrogen Passivation

Chen, Xin-Lian; Huang, Bao-Jun; Zhang, Chang-Wen; Li, Ping; Wang, Pei-Ji

doi:https://doi.org/10.1155/2017/4815251

Journal of Nanomaterials

On this page

Abstract Introduction Model Results and Discussion Conclusions Conflicts of Interest Acknowledgments References Copyright Related Articles

Research Article | Open Access

Volume 2017 | Article ID 4815251 | https://doi.org/10.1155/2017/4815251

Tunable SnO₂ Nanoribbon by Electric Fields and Hydrogen Passivation

Xin-Lian Chen,¹Bao-Jun Huang,¹Chang-Wen Zhang,¹Ping Li,¹and Pei-Ji Wang¹

Academic Editor: Shu Seki

Received12 Dec 2016

Accepted22 Feb 2017

Published20 Mar 2017

Abstract

Under external transverse electronic fields and hydrogen passivation, the electronic structure and band gap of tin dioxide nanoribbons (SnO₂NRs) with both zigzag and armchair shaped edges are studied by using the first-principles projector augmented wave (PAW) potential with the density function theory (DFT) framework. The results showed that the electronic structures of zigzag and armchair edge SnO₂NRs exhibit an indirect semiconducting nature and the band gaps demonstrate a remarkable reduction with the increase of external transverse electronic field intensity, which demonstrate a giant Stark effect. The value of the critical electric field for bare Z-SnO₂NRs is smaller than A-SnO₂NRs. In addition, the different hydrogen passivation nanoribbons (Z-SnO₂NRs-2H and A-SnO₂NRs-OH) show different band gaps and a slightly weaker Stark effect. The band gap of A-SnO₂NRs-OH obviously is enhanced while the Z-SnO₂NRs-2H reduce. Interestingly, the Z-SnO₂NRs-OH presented the convert of metal-semiconductor-metal under external transverse electronic fields. In the end, the electronic transport properties of the different edges SnO₂NRs are studied. These findings provide useful ways in nanomaterial design and band engineering for spintronics.

1. Introduction

The low-dimensional materials have attracted extensive attentions due to their excellent physical properties and novel electronic properties in the past decade. The graphene is especially discovered in 2004 [1]; it provides the new foundation for the research of low-dimensional systems [2–6]. However, graphene still faces many challenges, such as toxicity, lacking an intrinsic band gap, and incompatibility with current silicon-based electronic technology, which are in the way of the applications of graphene in electric devices [7]. Since the discovery of graphene, various 2D materials have been predicted and synthesized [8, 9], particularly, the group IV (Si, Ge, and Sn) analogs of graphene. The stanene may be a competitive candidate of graphene, because of the high conductivity of stanene [10], and its electric structure can be easily tuned [11]. The existing works have studied the effect of stain, substrate, external electric field, modification by functional groups, and so on [12, 13]. As in Modarresi et al. [14] tuning the band gap by the strain effect and external electric field (E-field) tends to open an energy gap predicated by Ren et al. [15]. In addition, Li and Zhang [16] studied tunable electronic structures and magnetic properties in two-dimensional stanene. Recently, the experiment and theory of one-dimensional (1D) graphene nanoribbons (GNRs) have been widely reported. In theoretical research, the zigzag GNRs can display the properties of half-metallicity by applying transverse electric field, promising candidate materials for spintronic devices [2, 4]. The electronic and optical properties of GNRs can be also modulated by changing edge termination [17]. Experimental results prove that the GNRs with various widths and crystallographic orientations are more facilitative and flexible than carbon nanotubes (CNTs), through standard lithographic procedures or chemical methods [3, 5]. Inspired by the fruitful results based on GNRs, recently a lot of interest has been drawn to nanoribbons of wide bandgap semiconductor, such as boron nitride (BNNRs) [18], molybdenum disulfide (MoS₂NRs) [19, 20], and zinc oxide (ZnONRs) [21]. In the calculation of zinc oxide (ZnONRs), the polarized spin density of states is a function of the nanoribbons width. Kou et al. demonstrate that the band gap of ZnO nanoribbon can be reduced monotonically with increasing transverse field strength, demonstrating a giant Stark effect [22]. The titania nanoribbons (TiO₂NRs) also predicate that the edge states and band gaps are sensitive to edge termination and ribbon width [23].

Tin dioxide (SnO₂) is also a typical wide-gap semiconductor with band gap = 3.6 eV, because of the fascinating electronic properties and optical transparency they have been widely used in photovoltaic devices, transparent conducting electrodes, solar cells, chemical gas sensors, and panel displays [24–30]. Recently, many theoretical researches have reported the electronic structures and geometric properties of SnO₂ nanomaterials using first-principles [31, 32]. More fortunately, the ultrathin SnO₂ nanofilm and one-dimensional (1D) SnO₂ nanoribbon have been synthesized by thermal evaporation and postprocessing in experiments [33]. Motivated by the outstanding properties of GNRs and wide band gap semiconductor, we put our emphasis on the SnO₂ nanoribbons, which may obtain more excellent achievement. In previous work, Huang et al. study the electronic structure bandgap modulations of SnO₂ nanoribbon by ribbon width [34].

In this paper, we perform first-principles calculations to study the bandgap modulations, electronic structures, and hydrogen passivation of SnO₂NRs under transverse electric fields. We found that both armchair and zigzag SnO₂NRs without hydrogen passivation are semiconductor with indirect gap and the semiconductor-metal transition occurs at a certain critical electric field. More interesting, partially passivating all the edge O atoms and passivating all the O and Sn atoms of SnO₂NRs could present the distinct properties. Our work offers a promising route toward modulating low-dimensional SnO₂ nanomaterials bandgap which have potential applications in nanoscale optical devices.

2. Model and Computational Methods

The electronic and optical properties of 1D SnO₂ nanostructures are performed with the spin-polarized first-principles methods as implemented in the Vienna ab initio simulation package (VASP) [35] and the subsequent electronic transport properties calculations are performed by the Atomistix Toolkit Package (ATK). Projector augmented wave (PAW) potentials and the Perdew et al. [36] function under the spin-polarized generalized gradient correlation are used to describe the exchange and correlation interaction. The supercells are large enough to ensure that the vacuum space is at least 15 Å, so that the interaction between nanostructures and their periodic images can be safely avoided. Following the Monkhorst-Pack scheme [37], 12 k points were used to sample the 1D Brillouin zone, and the convergence threshold was set as 10⁻⁴ eV in energy and 0.02 eV/Å in force. The valence electrons for the Sn, O, and Ag are 14 (Sn: 4d¹⁰ 5s²5p²), 6 (O: 2s² 2p⁴), and 11 (4d¹⁰5s¹). The positions of all the atoms in the supercell were fully relaxed during the geometry optimizations.

The model structures of SnO₂NRs were generated by cutting an SnO₂NS (tin dioxide nanosheets) along armchair and zigzag orientations, which are referred to as zigzag SnO₂ nanoribbons (Z-SnO₂NRs) and armchair SnO₂ nanoribbons (A-SnO₂NRs), as shown in Figure 1. The external electric field is modelled by transversely adding a sawtooth-like potential to the nanoribbon. We should explain that the DFT functional always underestimates the band gap of semiconductors, but it is powerful to predict a correct trend toward the band gap change and efficiently unveil the physical mechanism [38, 39].

3. Results and Discussion

3.1. The Band Gap Modulation under External Electric Field in Bare SnO₂ Nanoribbon

In both zigzag nanoribbon and armchair nanoribbon, the original package contains 8 tin atoms and 16 oxygen atoms. So, in our calculations we choose zigzag and armchair SnO₂ nanoribbons with width = 8. The results show that the electronic structures of zigzag and armchair edge SnO₂ nanoribbon exhibit an indirect semiconducting nature with the band gap of about 2.19 eV and 2.08 eV, respectively, which are well consistent with our previous results [34]. Firstly, we modulate band gaps of the bare SnO₂ nanoribbon by applying the transverse electronic fields. Considering the symmetrical structure of the Z-SnO₂NRs and A-SnO₂NRs, the external electric fields are added to the direction in Figure 1. The evolution of the band gaps for Z-SnO₂NRs and A-SnO₂NRs under different external electric field intensity is shown in Figure 2. From Figure 2, the band gaps of bare Z-SnO₂NRs and A-SnO₂NRs demonstrate a remarkable reduction when an external electric field is applied. The band gaps eventually closed when the electric field reached a critical value for each specified SnO₂ nanoribbon; this phenomenon is similar to the armchair ZnO nanoribbon [22]. The values of the critical electric field for bare Z-SnO₂NRs and A-SnO₂NRs are 0.124 V/Å and 0.210 V/Å, respectively. This suggests that the semiconductor-metal transition occurs at a certain value of critical electric field for Z-SnO₂NRs compared to A-SnO₂NRs.

To further investigate the underlying physical mechanism, the charge redistribution of Z-SnO₂NRs and A-SnO₂NRs is studied with and without an external electronic field, respectively. Figures 3(a)-3(b) show the band structure, density of state (DOS), and the corresponding charge densities for the conduction band minimum (CBM) and the valence band maximum (VBM) of Z-SnO₂NRs and A-SnO₂NRs at 0 V/Ǻ (a) and 0.13 V/Ǻ, respectively. From Figure 3, the band gap of the Z-SnO₂NRs is 2.19 eV under the electric field of 0 V/Ǻ. While the band gap of the Z-SnO₂NRs obviously becomes narrow and the DOS near the Fermi level are mainly ascribed to O 2p states and Sn 5d states under the electric field of 0.13 V/Ǻ. In addition, from Figure 3 (charge densities for CBM and VBM of Z-SnO₂NRs), we can find that when we applied an external electric field (0.13 V/Ǻ), the charge is evenly distributed, whereas VBM is a different localized state in which the wave function mainly focused on both sides of the O atoms for the whole nanoribbon.

(a)

(b)

In Figures 4(a)-4(b), band structure, DOS, and the corresponding charge densities for the CBM and VBM of the A-SnO₂NRs are illustrated at 0 V/Ǻ and 0.2 V/Ǻ. From Figure 4 we can find that the band gap of A-SnO₂NRs is 2.08 eV without electric field; the charge density of the CBM and VBM is different from the Z-SnO₂NRs and is edge state with wave function localized at the edge of the O atoms. The band gap becomes narrower and the DOS near the Fermi level is mainly caused by O 2p states with the external electric field of 0.2 V/Ǻ. Meanwhile, it is found that the charges are redistributed and the phenomenon of giant Stark effects appears, which is similar to ZnO nanoribbons [22, 40]. For the Z-SnO₂NRs, with the external electric field, the band gap is similar to the A-SnO₂NRs. In addition, the distribution of the wave function for CBM has no obvious change, while the wave functions of VBM gather to the edge O atoms and hardly have any wave function at the ribbon center, as shown in Figure 3(b). All in all, when we apply external electric field, due to the splitting of subbands levels caused by the charge redistribution, this makes the band gaps of SnO₂ nanoribbons decrease.

(a)

(b)

3.2. The Band Gap Modulation under External Electric Field in Hydrogen Passivation SnO₂ Nanoribbon

To explore the effect of edge hydrogen (H) termination on the electronic properties of the different SnO₂ nanoribbons, two different ways of nanoribbon edge hydrogen termination have been studied: (i) the edge of Sn and O atoms are passivated with H atoms (denoted SnO₂NR-2H) and (ii) the edge of O atoms are passivated (denoted SnO₂NR-OH), as shown in Figures 1(b)-1(c) and 1(e)-1(f). It is important for evaluation of the stability of SnO₂NRs because it can determine whether this nanostructure can be realized experimentally. The relative stability of bare and H passivated SnO₂NRs is determined by the binding energy (). is defined as , where represents different elements of Sn and O, and are the number and chemical potential for the corresponding element, respectively, and is the total free energy of system. According to the laws of thermodynamics, the larger the binding energy is, the more stable the structure is. The values of for different configurations of SnO₂ NRs are shown in Table 1.

From Table 1, the SnO₂NR-OH has a higher binding energy than bare SnO₂NRs and SnO₂NRs-2H. The binding energies of Z-SnO₂NRs-2H are 2.41 eV, which are slightly lower than the A-SnO₂NRs; this demonstrates that Z-SnO₂NRs-2H is more active than the other SnO₂ nanoribbons.

Compared to the bare SnO₂NRs, the behavior of the H passivation nanoribbons changed significantly. The A-SnO₂NRs-OH and Z-SnO₂NRs-2H remain semiconducting properties (the band gaps are 2.64 eV and 2.41 eV, resp.), but the band gap of A-SnO₂NRs-OH is obviously enhanced while the Z-SnO₂NRs-2H reduce. Similarly, we take the A₈-SnO₂NR-OH (width = 8) as an example; the calculated band gap is 2.42 eV, slightly larger than 2.08 eV of the bare armchair ribbon. For Z₈-SnO₂NR-2H, the calculated band gap is 1.71 eV, obviously smaller than 2.19 eV of the bare zigzag nanoribbon. The A₈-SnO₂NR-2H and Z₈-SnO₂NR-OH present the metallic property which supplied by the 2p state of edge O atoms and the 5s state of the edge Sn atoms.

To further study the effect of external electronic field for H passivation SnO₂NRs, we calculate the evolutions of the band gap for H passivation with different external electric field in Figure 5. From Figure 5 we can find that because no pronounced differences are found when the field direction is reversed, owing to the symmetrical structure, A-SnO₂NRs-OH has a slower decreasing rate of the band gap with the increase of electric field and requires a larger critical electric field to close its band gap, which is similar to Kou et al. [22]. A vital reason is that the A-SnO₂NRs-OH has larger band gaps than the bare ones and the unpaired electrons reduce when H atoms are introduced. For the Z-SnO₂NRs-2H, the decreasing rate of the band gap is faster than A-SnO₂NRs-OH and it has a lower critical electric field of 0.13 eV to close its band gap. This phenomenon well corresponds to the bare SnO₂ nanoribbons. It illustrates that the Z-SnO₂NRs-2H are more sensitive to external electric field than A-SnO₂NRs-OH. There is special phenomenon that presents metallic property for Z-SnO₂NRs-OH (the band gap is 0 eV) when it is without external electric field. Interestingly, it realizes a transformation from metal to semiconductor when the electric field reaches 0.07 eV/Å. The band gap has the maximum value of 1.3 eV when the external electric field increases to 0.15 eV/Å and subsequently the band gap decreases with the increase of the external electric field which is similar to Zheng et al. [41].

To reveal the underlying physical mechanism for the different H passivation models, band structure and the charge redistribution of the CBM and VBM are examined. Figures 6(a)-6(b) show band structure and the corresponding charge densities for CBM and VBM of A-SnO₂NRs-OH at 0 v/Ǻ (a) and 0.15 v/Ǻ, respectively. From Figure 6(a), the charge distribution of the CBM almost concentrated at O atoms of the whole ribbon except for the ribbon edges, while the charge distribution of the VBM is totally concentrated at the Sn atoms and O atoms of the ribbon edges which is similar to the VBM of A-SnO₂NRs. Once an external electric field is applied, the charge distributions of the CBM and VBM are driven to localize at opposite edges owing to the different electrostatic potential, as analyzed above, as shown in Figure 6(b). This can shift down the CBM because the charge easily redistributes in external electric fields, while the VBM also obviously upshifts in energy band toward the Fermi level, thereby further narrowing the energy gap.

(a)

(b)

Band structure and the charge redistribution of H passivation Z-SnO₂NRs were presented in Figures 7 and 8. From Figure 7, we can conclude that it is an indirect gap semiconductor regardless of whether or not the electric field is applied. The charges of CBM and VBM mainly concentrate at the O atoms and Sn atoms of the ribbon edges as shown in Figure 7(a). That is different from the bare Z-SnO₂NRs in which the charge mainly concentrates at the O atoms in whole nanoribbon. From Figure 7(b), under the electronic field of 0.2 v/Ǻ, the charge distributions of the CBM and VBM are driven to localize at opposite edges; this situation is similar to the A-SnO₂NRs-OH. In Figure 8, the wave function of the CBM primarily localize at O atoms and Sn atoms of the nanoribbon center, whereas the wave function of VBM mainly concentrates at the O atoms of the whole nanoribbon and the Sn atoms of the right nanoribbon edge. The hydrogenation of Z-SnO₂NRs destructed the symmetry of Z-SnO₂NRs-2H, which made the charge densities for VBM of Z-SnO₂NRs-2H asymmetric, which we can see from Figure 8. In addition, the charges are redistributed because the electrostatic potential symmetry is broken under an external electric field. The wave functions of the CBM and VBM states are localized at the opposite edge. This charge redistribution results in the transition of electrons between the valence and conduction band and splitting of the subband levels. Subsequently, this makes the decreasing of the band gaps and enhances the conductivity of the SnO₂NRs materials.

(a)

(b)

(a)

(b)

3.3. Electronic Transport

The lower dimension semiconductors are usually used to fabricate electronic transport devices, such as graphene and silicone nanoribbon [42, 43]. The electronic transmission of SnO₂ nanoribbon can be explored in terms of transport property. The transmission of SnO₂ nanoribbon is determined with two probe methods. The two ends of SnO₂ nanoribbon are held within the electrodes. The width of left electrode and right electrode is 3.15 Å, respectively, as shown in Figure 1(h). The electrons near the Fermi level contribute to electronic transport property in SnO₂ nanoribbon. The orbital delocalization near the Fermi level results in high mobility of electrons which corresponds to certain peak amplitudes in the transmission spectrum [44, 45]. The current through the system is calculated using the Landauer–Büttiker formula: [46, 47], where is the electron charge, is Planck’s constant, is the transmission probability through the junction for an electron at energy and an applied bias voltage , is the Fermi-Dirac distribution function, and , is the electrochemical potential of the left and right electrode, respectively.

The electronic transmission is invoked with magnitude of transmission in a particular energy interval. Figure 9 represents the transmission spectrum of A-SnO₂NRs and Z-SnO₂NRs. The width of the center scattering region is 0.02 eV and 0.05 eV for A-SnO₂NRs and Z-SnO₂NRs, respectively. For A-SnO₂NRs, the transmission peaks are observed for −2.8 V, −2.4 V, and −1.7 V in the valence band and 1.5 V and 2.8 V in the conduction band. Compared with A-SnO₂NRs, more peaks of Z-SnO₂NRs are observed in the valence band. The peaks locate at −2.8 V, −2.5 V, −1.7 V, and −1.1 V in valence band; the location of peaks is similar to A-SnO₂NRs in conduction band. This is also in agreement with the electron density of Z-SnO₂NRs, where the electron density is more intense than A-SnO₂NRs. In addition, compared to Z-SnO₂NRs, A-SnO₂NRs has a larger cutting area near the Fermi surface, which is closely related to a larger band gap for A-SnO₂NRs, which also shows that the transmission spectrum of materials has close correlation for electronic density of states.

The calculated I-V characteristics of SnO₂NRs are illuminated in Figure 10. From Figure 10 we can find that the A-SnO₂NR and Z-SnO₂NR are in off state when the bias voltage is between −0.3 V and 0.3 V. When the bias voltage exceeds 0.3 V, the current presents a nonlinear increase and same change trend for A-SnO₂NR and Z-SnO₂NR, similar to the electrons conduction of the other semiconductors, such as ZnO and TiO₂. Since 0.8 V, the change of the bias voltage not only produces the conduction current, which also makes the current have a nonlinear growth; this phase of the V-I characteristic curve is similar to general electronic conduction semiconductor devices. The difference of the I-V curve can be explained by the fact that the A-SnO₂NR and Z-SnO₂NR possess the different band gap and voltage sensitivity. The thickness of SnO₂NR is similar to the thickness of three atoms and two-dimensional electron gas can be formed; in addition, similar to the graphene, SnO₂ can be self-assembled on the experimental generation. Based on these special electronic transport properties, the SnO₂ nanoribbons have enormous potential application in the switching, rectifying devices and the whole semiconductor industry.

4. Conclusions

In summary, the electronic structures and band gap modulations of the Z-SnO₂NRs and A-SnO₂NRs influenced by an external transverse electronic field and hydrogen passivation have been investigated by using the first-principle PAW potential within the DFT framework under GGA. As affected by a transverse electric field, the band gaps of bare Z-SnO₂NRs and A-SnO₂NRs demonstrate a remarkable reduction and the semiconductor-metal transition would appear at a lower value of critical electric field. The charge density near the Fermi can be redistributed. For the SnO₂NRs with edge hydrogen termination through different way, the Z-SnO₂NRs-2H and A-SnO₂NRs-OH remain semiconducting properties, but the change of the band gap for the A-SnO₂NRs-OH and Z-SnO₂NRs-2H is obviously different. The Z-SnO₂NRs-2H are more sensitive to external electric field than A-SnO₂NRs-OH. For the Z-SnO₂NRs-OH, it can realize transformation from metal to semiconductor when the electric field reaches 0.07 eV/Å. Additionally, it indicates that more peaks of Z-SnO₂NRs are observed in the valence band compared with A-SnO₂NRs by electronic transport properties. There is similar variation tendency of the I-V characteristics of both A-SnO₂NR and Z-SnO₂NR. Our results may be very useful theoretical reference to design nanoelectronic and spintronic devices.

Conflicts of Interest

The authors declare no competing financial interest.

Acknowledgments

This work was supported by the National Natural Science Foundation of China (Grants nos. 61571210, 61172028, 11274143, and 11304121), the Natural Science Foundation of Shandong Province (Grant no. ZR2010EL017), and Research Fund for the Doctoral of University of Jinan (Grant no. XBS1452).

References

K. S. Novoselov, A. K. Geim, S. V. Morozov et al., “Electric field in atomically thin carbon films,” Science, vol. 306, no. 5696, pp. 666–669, 2004.
View at: Publisher Site | Google Scholar
Y.-W. Son, M. L. Cohen, and S. G. Louie, “Half-metallic graphene nanoribbons,” Nature, vol. 444, no. 7117, pp. 347–349, 2006.
View at: Publisher Site | Google Scholar
X. Li, X. Wang, L. Zhang, S. Lee, and H. Dai, “Chemically derived, ultrasmooth graphene nanoribbon semiconductors,” Science, vol. 319, no. 5867, pp. 1229–1232, 2008.
View at: Publisher Site | Google Scholar
E.-J. Kan, H. J. Xiang, J. Yang, and J. G. Hou, “Electronic structure of atomic Ti chains on semiconducting graphene nanoribbons: a first-principles Study,” Journal of Chemical Physics, vol. 127, no. 16, Article ID 164706, 2007.
View at: Publisher Site | Google Scholar
Q. Yan, B. Huang, J. Yu et al., “Intrinsic current-voltage characteristics of graphene nanoribbon transistors and effect of edge doping,” Nano Letters, vol. 7, no. 6, pp. 1469–1473, 2007.
View at: Publisher Site | Google Scholar
P. Koskinen, S. Malola, and H. Häkkinen, “Self-passivating edge reconstructions of graphene,” Physical Review Letters, vol. 101, no. 11, Article ID 115502, 2008.
View at: Publisher Site | Google Scholar
D. L. Miller, K. D. Kubista, G. M. Rutter et al., “Structural analysis of multilayer graphene via atomic moiré interferometry,” Physical Review B, vol. 81, no. 12, Article ID 125427, 2010.
View at: Publisher Site | Google Scholar
K. S. Novoselov, D. Jiang, F. Schedin et al., “Two-dimensional atomic crystals,” Proceedings of the National Academy of Sciences of the United States of America, vol. 102, no. 30, pp. 10451–10453, 2005.
View at: Publisher Site | Google Scholar
S. Z. Butler, S. M. Hollen, L. Cao et al., “Progress, challenges, and opportunities in two-dimensional materials beyond graphene,” ACS Nano, vol. 7, no. 4, pp. 2898–2926, 2013.
View at: Publisher Site | Google Scholar
F.-F. Zhu, W.-J. Chen, Y. Xu et al., “Epitaxial growth of two-dimensional stanene,” Nature Materials, vol. 14, no. 10, pp. 1020–1025, 2015.
View at: Publisher Site | Google Scholar
B. Peng, H. Zhang, H. Shao, Y. Xu, X. Zhang, and H. Zhu, “Low lattice thermal conductivity of stanene,” Scientific Reports, vol. 6, Article ID 20225, 2016.
View at: Publisher Site | Google Scholar
W. Xiong, C. Xia, T. X. Wang, Y. Peng, and Y. Jia, “Strain and spin-orbital coupling effects on electronic structures and magnetism of semi-hydrogenated stanene,” The Journal of Physical Chemistry C, vol. 120, no. 19, pp. 10622–10628, 2016.
View at: Publisher Site | Google Scholar
T. Osaka, H. Omi, K. Yamamoto, and A. Ohtake, “Surface phase transition and interface interaction in the -Sn/InSb111 system,” Physical Review B, vol. 50, no. 11, pp. 7567–7572, 1994.
View at: Publisher Site | Google Scholar
M. Modarresi, A. Kakoee, Y. Mogulkoc, and M. R. Roknabadi, “Effect of external strain on electronic structure of stanene,” Computational Materials Science, vol. 101, pp. 164–167, 2015.
View at: Publisher Site | Google Scholar
C.-C. Ren, W.-X. Ji, C.-W. Zhang, P. Li, and P.-J. Wang, “The effects of biaxial strain and electric field on the electronic properties in stanene,” Materials Research Express, vol. 3, no. 10, Article ID 105008, 2016.
View at: Publisher Site | Google Scholar
S. S. Li and C. W. Zhang, “Tunable electronic structures and magnetic properties in two-dimensional stanene with hydrogenation,” Materials Chemistry and Physics, vol. 173, pp. 246–254, 2016.
View at: Publisher Site | Google Scholar
D. Prezzi, D. Varsano, A. Ruili, A. Marini, and E. Molinari, “Optical properties of graphene nanoribbons: the role of many-body effects,” Physical Review B: Condensed Matter and Materials Physics, vol. 77, Article ID 041404, 2008.
View at: Google Scholar
W. Chen, Y. Li, G. Yu et al., “Hydrogenation: a simple approach to realize semiconductor-half-metal-metal transition in boron nitride nanoribbons,” Journal of the American Chemical Society, vol. 132, no. 5, pp. 1699–1705, 2010.
View at: Publisher Site | Google Scholar
Y. Li, Z. Zhou, S. Zhang, and Z. Chen, “MoS2 nanoribbons: high stability and unusual electronic and magnetic properties,” Journal of the American Chemical Society, vol. 130, no. 49, pp. 16739–16744, 2008.
View at: Publisher Site | Google Scholar
H. Pan and Y.-W. Zhang, “Edge-dependent structural, electronic and magnetic properties of MoS2 nanoribbons,” Journal of Materials Chemistry, vol. 22, no. 15, pp. 7280–7290, 2012.
View at: Publisher Site | Google Scholar
A. R. Botello-Méndez, F. López-Urías, M. Terrones, and H. Terrones, “Magnetic behavior in zinc oxide zigzag nanoribbons,” Nano Letters, vol. 8, no. 6, pp. 1562–1565, 2008.
View at: Publisher Site | Google Scholar
L. Kou, C. Li, Z. Zhang, and W. Guo, “Electric-field- and hydrogen-passivation-induced band modulations in armchair ZnO nanoribbons,” Journal of Physical Chemistry C, vol. 114, no. 2, pp. 1326–1330, 2010.
View at: Publisher Site | Google Scholar
T. He, F. Pan, Z. Xi et al., “First-principles study of titania nanoribbons: formation, energetics, and electronic properties,” Journal of Physical Chemistry C, vol. 114, no. 20, pp. 9234–9238, 2010.
View at: Publisher Site | Google Scholar
S. Ferrere, A. Zaban, and B. A. Gregg, “Dye sensitization of nanocrystalline tin oxide by perylene derivatives,” Journal of Physical Chemistry B, vol. 101, no. 23, pp. 4490–4493, 1997.
View at: Publisher Site | Google Scholar
M. Khan, J. Xu, N. Chen, and W. Cao, “First principle calculations of the electronic and optical properties of pure and (Mo, N) co-doped anatase TiO2,” Journal of Alloys and Compounds, vol. 513, pp. 539–545, 2012.
View at: Publisher Site | Google Scholar
H. Takakura, M.-S. Choe, and Y. Hamakawa, “Paint-on-diffusant SnO₂/n⁺-p Si heteroface solar cell,” Japanese Journal of Applied Physics, vol. 19, no. 19, pp. 61–65, 1980.
View at: Publisher Site | Google Scholar
Z. Zhang, C. Shao, X. Li et al., “Electrospun nanofibers of ZnO-SnO2 heterojunction with high photocatalytic activity,” Journal of Physical Chemistry C, vol. 114, no. 17, pp. 7920–7925, 2010.
View at: Publisher Site | Google Scholar
S. Tamura, T. Ishida, H. Magara, T. Mihara, O. Tabata, and T. Tatsuta, “Transparent conductive tin oxide films by photochemical vapour deposition,” Thin Solid Films, vol. 343-344, no. 1-2, pp. 142–144, 1999.
View at: Publisher Site | Google Scholar
H. J. Snaith and C. Ducati, “SnO2-Based dye-sensitized hybrid solar cells exhibiting near unity absorbed photon-to-electron conversion efficiency,” Nano Letters, vol. 10, no. 4, pp. 1259–1265, 2010.
View at: Publisher Site | Google Scholar
R.-S. Zhang, Y. Liu, Q. Gao et al., “First-principles study on the electronic and optical properties of F- and Nb-doped anatase TiO2,” Journal of Alloys and Compounds, vol. 509, no. 37, pp. 9178–9182, 2011.
View at: Publisher Site | Google Scholar
D. O. Scanlon and G. W. Watson, “On the possibility of p-type SnO₂,” Journal of Materials Chemistry, vol. 22, no. 48, pp. 25236–25245, 2012.
View at: Publisher Site | Google Scholar
A. Schleife, J. B. Varley, F. Fuchs et al., “Tin dioxide from first principles: quasiparticle electronic states and optical properties,” Physical Review B: Condensed Matter and Materials Physics, vol. 87, Article ID 239901, 2013.
View at: Google Scholar
G. Rahman, V. M. García-Suárez, and J. M. Morbec, “Intrinsic magnetism in nanosheets of SnO2: a first-principles study,” Journal of Magnetism and Magnetic Materials, vol. 328, pp. 104–108, 2013.
View at: Publisher Site | Google Scholar
B.-J. Huang, F. Li, C.-W. Zhang, P. Li, and P.-J. Wang, “Electronic structure and optical properties of Ag-doped SnO₂ nanoribbons,” RSC Advances, vol. 4, no. 79, pp. 41819–41824, 2014.
View at: Publisher Site | Google Scholar
G. Kresse and D. Joubert, “From ultrasoft pseudopotentials to the projector augmented-wave method,” Physical Review B, vol. 59, no. 3, pp. 1758–1775, 1999.
View at: Publisher Site | Google Scholar
J. P. Perdew, K. Burke, and M. Ernzerhof, “Generalized gradient approximation made simple,” Physical Review Letters, vol. 77, no. 18, pp. 3865–3868, 1996.
View at: Publisher Site | Google Scholar
H. J. Monkhorst and J. D. Pack, “Special points for Brillouin-zone integrations,” Physical Review. B. Solid State, vol. 13, no. 12, pp. 5188–5192, 1976.
View at: Publisher Site | Google Scholar | MathSciNet
Z. Zhang and W. Guo, “Energy-gap modulation of BN ribbons by transverse electric fields: first-principles calculations,” Physical Review B—Condensed Matter and Materials Physics, vol. 77, no. 7, Article ID 075403, 2008.
View at: Publisher Site | Google Scholar
C.-W. Chen, M.-H. Lee, and S. J. Clark, “Band gap modification of single-walled carbon nanotube and boron nitride nanotube under a transverse electric field,” Nanotechnology, vol. 15, no. 12, pp. 1837–1843, 2004.
View at: Publisher Site | Google Scholar
K. H. Khoo, M. S. C. Mazzoni, and S. G. Louie, “Tuning the electronic properties of boron nitride nanotubes with transverse electric fields: a giant dc Stark effect,” Physical Review B, vol. 69, no. 20, Article ID 201401, 2004.
View at: Publisher Site | Google Scholar
F. Zheng, Z. Liu, J. Wu, W. Duan, and B.-L. Gu, “Scaling law of the giant Stark effect in boron nitride nanoribbons and nanotubes,” Physical Review B—Condensed Matter and Materials Physics, vol. 78, no. 8, Article ID 085423, 2008.
View at: Publisher Site | Google Scholar
H. Goto, E. Uesugi, R. Eguchi, A. Fujiwara, and Y. Kubozono, “Edge-dependent transport properties in graphene,” Nano Letters, vol. 13, no. 3, pp. 1126–1130, 2013.
View at: Publisher Site | Google Scholar
R. Quhe, R. Fei, Q. Liu et al., “Tunable and sizable band gap in silicene by surface adsorption,” Scientific Reports, vol. 2, article 853, 2012.
View at: Publisher Site | Google Scholar
S. Yamacli, “Comparison of the electronic transport properties of metallic graphene and silicene nanoribbons,” Journal of Nanoparticle Research, vol. 16, no. 8, article 2576, 2014.
View at: Publisher Site | Google Scholar
H. Fueno, Y. Kobayashi, and K. Tanaka, “Theoretical study of current-voltage characteristics of carbon nanotube wire functionalized with hydrogen atoms,” Science China Chemistry, vol. 55, no. 5, pp. 796–801, 2012.
View at: Publisher Site | Google Scholar
M. Büttiker, Y. Imry, R. Landauer, and S. Pinhas, “Generalized many-channel conductance formula with application to small rings,” Physical Review B, vol. 31, no. 10, pp. 6207–6215, 1985.
View at: Publisher Site | Google Scholar
D. Zha, C. Chen, and J. Wu, “Electronic transport through a silicene-based zigzag and armchair junction,” Solid State Communications, vol. 219, pp. 21–24, 2015.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2017 Xin-Lian Chen et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

1049

Downloads

1110

Citations

Journal of Nanomaterials

Tunable SnO2 Nanoribbon by Electric Fields and Hydrogen Passivation

Abstract

1. Introduction

2. Model and Computational Methods

3. Results and Discussion

3.1. The Band Gap Modulation under External Electric Field in Bare SnO2 Nanoribbon

3.2. The Band Gap Modulation under External Electric Field in Hydrogen Passivation SnO2 Nanoribbon

3.3. Electronic Transport

4. Conclusions

Conflicts of Interest

Acknowledgments

References

Copyright

Tunable SnO₂ Nanoribbon by Electric Fields and Hydrogen Passivation

3.1. The Band Gap Modulation under External Electric Field in Bare SnO₂ Nanoribbon

3.2. The Band Gap Modulation under External Electric Field in Hydrogen Passivation SnO₂ Nanoribbon