Facile Synthesis, Microstructure, and Gas Sensing Properties of NdCoO<sub>3</sub> Nanoparticles

Gildo-Ortiz, Lorenzo; Guillén-Bonilla, Héctor; Reyes-Gómez, Juan; Rodríguez-Betancourtt, Verónica María; Olvera-Amador, M. de la L.; Eguía-Eguía, Sandra Irene; Guillén-Bonilla, Alex; Santoyo-Salazar, Jaime

doi:https://doi.org/10.1155/2017/8174987

Journal of Nanomaterials

On this page

Abstract Introduction Results and Discussion Conclusions Conflicts of Interest Acknowledgments References Copyright Related Articles

Research Article | Open Access

Volume 2017 | Article ID 8174987 | https://doi.org/10.1155/2017/8174987

Facile Synthesis, Microstructure, and Gas Sensing Properties of NdCoO₃ Nanoparticles

Lorenzo Gildo-Ortiz,¹Héctor Guillén-Bonilla,²Juan Reyes-Gómez,³Verónica María Rodríguez-Betancourtt,⁴M. de la L. Olvera-Amador,⁵Sandra Irene Eguía-Eguía,¹Alex Guillén-Bonilla,⁶and Jaime Santoyo-Salazar⁷

Academic Editor: Oscar Perales-Pérez

Received15 Apr 2017

Revised27 Jun 2017

Accepted06 Jul 2017

Published03 Aug 2017

Abstract

NdCoO₃ nanoparticles were successfully synthesized by a simple, inexpensive, and reproducible solution method for gas sensing applications. Cobalt nitrate, neodymium nitrate, and ethylenediamine were used as precursors and distilled water as solvent. The solvent was evaporated later by means of noncontinuous microwave radiation at 290 W. The obtained precursor powders were calcined at 200, 500, 600, and 700°C in a standard atmosphere. The oxide crystallized in an orthorhombic crystal system with space group Pnma (62) and cell parameters Å, Å, and Å. The nanoparticles showed a diffusional growth to form a network-like structure and porous adsorption configuration. Pellets prepared from NdCoO₃ were tested as gas sensors in atmospheres of carbon monoxide and propane at different temperatures. The oxide nanoparticles were clearly sensitive to changes in gas concentrations (0–300 ppm). The sensitivity increased with increasing concentration of the gases and operating temperatures (25, 100, 200, and 300°C).

1. Introduction

Perovskite-type oxides with ABO₃ structure and related materials constitute a group of compounds with a significant technological value because of their interesting physical and chemical properties [1–8]. Within this family of compounds, cobaltites, of general formula RECoO₃ (RE = rare earth like La, Nd, Gd, etc.), have been widely studied for their important applications as catalysts, thermoelectric compounds, cathodes for solid-oxide fuel-cells, and gas sensors [9–12]. Several investigations have shown that the presence of cobalt ions, with different oxidation states, plays an important role in the transport properties and catalytic activity of perovskites [13, 14]. Furthermore, the ability to modify their microstructures, such as porosity, distribution, shape, and particle size can induce changes in their physical properties [15, 16]. Owing to the nanometric size of the perovskite particles, many applications are potentiated. Nowadays, various synthesis methods are investigated in order to achieve control of the size and shape of the nanoparticles. These methods include sol-gel routes, hydrothermal, solid-state reaction, coprecipitation, spray pyrolysis, solution-combustion processes, and physical vapor deposition [17]. In particular, “soft” chemistry methods allow a better control on the stoichiometry and a reduction of the synthesis temperature, which permits obtaining homogeneous nanoparticles [18].

The perovskite-type oxides are of particular interest in the field of gas sensors because they exhibit a high melting point, chemical stability under reducing and oxidizing environments, and a dependency of the partial pressure of oxygen on the concentration of point defects [19]. Among the mixed valence perovskites, NdCoO₃ stands out as a strong candidate for gas sensors because it has a high sensitivity to gases, mainly carbon monoxide (CO) [20, 21]. One reason for the high response in gases is that the oxide crystallizes in a perovskite-type structure, where neodymium ions (Nd³⁺) are dodecahedrally coordinated, while cobalt has an octahedral coordination but not an integer oxidation state [20]. This latter occurs because cobalt can fluctuate between two stable oxidation states producing oxygen-deficient perovskites () with a mixed valence state for cobalt: Co²⁺ and Co³⁺, where Co³⁺ dominate [22]. The equilibration of oxygen in the gas phase with oxygen vacancies in the oxide favors the response of the perovskite as gas sensor [19]. However, it is necessary to optimize the performance of this material giving emphasis to its microstructure in order to achieve a functional behavior as gas sensor. In particular, the development of sensors for the detection of carbon monoxide (CO) and gaseous hydrocarbons requires special attention because of their potential hazards [23]. CO is one of the most abundant toxic gases and is characterized by being odorless and colorless. Prolonged exposure to this gas can cause damage to the human body and even death, while gaseous hydrocarbons are usually flammable gases with no odor or color. In this regard, one of the objectives of this work was to synthesize NdCoO₃ nanoparticles by a simple method using relatively low calcination temperatures. Another objective was to measure the response of the material’s sensitivity in CO and propane, several concentrations of them, and operating temperatures.

2. Experimental Procedures

2.1. NdCoO₃ Synthesis

NdCoO₃ nanoparticles with perovskite structure were synthesized by a solution method assisted by microwave radiation. 0.004 mole of Nd(NO₃)₃·6H₂O (Aldrich, 99.9%), 0.004 mole of Co(NO₃)₂·6H₂O (Jalmek, 98.6%), and 0.030 mole of ethylenediamine (Sigma, ≥99.5%) were separately dissolved in distilled water. The cobalt nitrate and ethylenediamine solutions were mixed slowly and the mixture was later stirred for 20 min at 375 rpm. The neodymium nitrate solution was slowly added to the mixture and the stirring continued for 24 h at room temperature. Evaporation of the solvent was carried out using noncontinuous microwave radiation at 290 W using a domestic microwave oven (LG, model MS1147). The microwave radiation was applied in steps of 60 to 90 s to maintain the suspension’s temperature below 90°C. Control of temperature and exposure times was needed to prevent loss of material. The paste produced from evaporation was dried at 200°C for 8 h in a normal atmosphere, and the obtained powders were divided into three parts and they were calcined at 500, 600, and 700°C, respectively. For this, a heating rate of 100°C/h was employed with a residence time of 5 h. The heat treatment was performed in a programmable oven (Vulcan™) temperature control.

2.2. Characterization of NdCoO₃ Powders

All the calcined powders were analyzed by X-ray powder diffraction (XRD) at room temperature using a Rigaku SmartLab diffractometer, with CuKα radiation and nickel filter. The 2θ scanning range was from 20 to 70°, with steps of 0.02° and a duration of 1 s per step. The material’s microstructure was analyzed by scanning electron microscopy (SEM, JEOL JSM-6390LV) in high vacuum mode using the secondary electron (SE) emission. The surface chemical composition was analyzed by energy dispersive X-ray spectroscopy (EDS-SEM) with a Bruker 5010 XFlash detector. To observe the nanoparticles, a transmission electron microscope (TEM, JEOL JEM-2010) with an accelerating voltage of 200 kV was employed. For this, a representative sample of the powder was used, which was dispersed in isopropyl alcohol for 5 min and placed on a copper grid. The surface area of the powders was assessed by nitrogen physisorption at 77 K using a Minisorp II BEL Japan equipment. Prior to the nitrogen adsorption process, the chamber with the sample was degassed and maintained under vacuum for 24 h at room temperature. The powder topology was analyzed by atomic force microscopy (AFM) using a JSPM-5200 microscope from JEOL under intermittent contact operations under normal pressure conditions.

2.3. Gas Sensitivity Tests

The sensitivity tests of the NdCoO₃ were performed in atmospheres of carbon monoxide (CO) and propane (C₃H₈). The electrical resistance of NdCoO₃ pellets with a diameter of 12 mm and a thickness of 500 μm was measured. The pellets were made with 0.3 g of NdCoO₃ powders at a pressure of 10 tons during 30 min using a Simplex Ital Equip-25 tons pressing machine. Two ohmic contacts were placed on the surface of the pellets using colloidal silver paint (Alfa Aesar, >99%). The pellets were placed into a measuring chamber with a vacuum capacity of 10^-3torr. The gas concentration inside the chamber was electronically monitored by a Leybold (model TM20) vacuum gauge. The fed gas concentrations were 0, 5, 50, 100, 200, and 300 ppm. The operating temperature was electronically controlled using a type J thermocouple with four fixed values: 25, 100, 200, and 300°C. The electrical resistance was recorded using a Keithley 2001 digital multimeter. The sensitivity (S) was calculated by the relative difference in electrical conductances using the expression , where and denote electrical conductances in the sampled gas (CO or C₃H₈) and air, respectively. Figure 1 shows a diagram of the system used for the material’s characterization in the gases.

3. Results and Discussion

3.1. XRD Analysis

Figure 2 shows the X-ray diffraction patterns of the calcined powders at 200, 500, 600, and 700°C. From the spectra array it can be observed that paste calcined at 200°C is amorphous, since the diffractogram does not show defined peaks. The spectra of powders calcined at 500, 600, and 700°C present the diffraction peaks corresponding to the NdCoO₃ phase with perovskite structure. These peaks were observed at the 2θ angular positions 23.6°, 26.5°, 33.6°, 35.8°, 41.5°, 48.3°, 49.8°, 54.3°, 55.8°, and 60.0°, which are indexed according to the reference from The International Centre for Diffraction Data, ICDD, 00-052-1279-PDF as the following crystal planes: (020), (111), (121), (210), (220), (202), (212), (103), (311), and (123), respectively. The NdCoO₃ crystallized in an orthorhombic system with space group Pnma (62) and cell parameters Å, Å, and Å. At higher calcination temperatures, the peaks in the spectra are of higher amplitude, better defined, and with a relative low level of noise, all of which are associated with a better crystallinity, especially the sample obtained at 700°C.

We found in this work that, using the solution method, NdCoO₃ powders can be synthesized at a relative low temperature of 700°C, which is lower than those used in others methods to produce these compounds. For example, using the sol-gel method (in the presence of urea), NdCoO₃ was obtained using a sintering temperature of 1100°C [20]; the compound series ACoO₃ has been synthesized by calcining at 1100°C per 3 h (for A = Pr, Nd, Sm, and Gd) [24], and at 700°C per 5 h followed by a sintering step at 1000°C per 8 h (for A = Pr, Nd, Tb, and Dy) [25]; through the conventional solid-state reaction method, NdCoO₃, Nd_0.8Ca_0.2CoO₃, and Nd_0.8Sr_0.2CoO₃ have been synthesized at the temperatures 900–1050°C with calcination times of 24 h [26]; NdCoO₃ has been also synthesized through calcination at 900°C from a precursor reactive paste [27]. Table 1 shows a summary of the methods commonly employed to synthesize this perovskite. After reviewing literature, the method used in this work can be considered as a simple and efficient route to synthesize NdCoO₃.

3.2. SEM Analysis and N₂ Adsorption

The following results were obtained for the NdCoO₃ powders obtained at 700°C. Figures 3(a)–3(d) show typical SEM micrographs of the NdCoO₃ powders. The images were taken at these magnifications: (a) 500x, (b) 2000x, (c) 5000x, and (d) 10000x (inset: 30000x). It can be seen in Figures 3(a) and 3(b) that the oxide’s surface has a lot of different sized pores (in a range 0.5 to 25 μm), which confers it a sponge-like morphology. In Figures 3(c) and 3(d), at higher magnification, it can be clearly observed an agglomeration of particles with high connectivity between them, forming a network-like structure. In addition, smaller pores can be observed (with a size of about 0.2 μm). This porosity is also attributable to the gases released during thermal decomposition of organic matter, mainly water vapor, NO_x, and CO₂ [28].

Figure 4 shows a typical EDS-SEM spectrum obtained from the NdCoO₃ powders. In this spectrum, the characteristic Nd, Co, and O peaks, according to the material’s chemical composition, can be identified. For neodymium (Nd), the peak of greatest intensity in the spectrum corresponds to the characteristic line Lα, whose energy is 5.22 keV. For cobalt (Co), three peaks located at 0.77, 6.92, and 7.65 keV correspond to the characteristic Lα, Kα, and Kβ lines, respectively. For oxygen (O), the corresponding line is Kα, whose energy is 0.53 keV. The peak located at 0.28 KeV denotes the presence of carbon (C), which is a residue of the thermal decomposition of organic matter, this being one of the disadvantages of using organic reagents in the preparation of inorganic materials [29]. In addition, the EDS-SEM elemental composition (Nd : Co : O at. % 20.72 : 21.13 : 58.15) corresponds nearly to the theoretical atomic composition of the NdCoO₃ (Nd : Co : O at. % 20 : 20: 60). The slight deviation can be attributed to traces of metal oxides remaining in the sample.

Figure 5 shows the N₂ adsorption isotherm of the NdCoO₃ powders at 77 K and the corresponding BET plot (inset). The shape of the isotherm was characterized as type II according to IUPAC’s classification; this isotherm, which shows a weak hysteresis, is typically obtained in the case of macroporous solids. The specific surface area was of 7.52 m²/g. In general, these oxides exhibit relatively low surface areas: in the range of 3 to 14 m²/g [30–32]. Our result agrees well in this range.

3.3. TEM Analysis

Figures 6(a)–6(e) show TEM images of the NdCoO₃ synthesized at 700°C and the particle size distribution. From Figure 6(a) it is clear that the NdCoO₃ powders are comprised of nanometer sized particles, which possess an irregular shape and are connected to each other, in agreement with the SEM analysis (Figure 3). According to the analysis of multiple TEM images, where the particles were clearly identifiable, it was estimated that their size is in the range of 17 to 151 nm; about 80% of the particles are within the range of 17 to 100 nm; their average size is 66 nm with a standard deviation of 37 nm (Figure 6(b)). Figures 6(c) and 6(d) show images obtained by high-resolution transmission electron microscopy (HRTEM), where fringes can be seen on the material’s crystal lattice. These images reveal that the interplanar distances are about 2.6 and 3.7 Å (inset in Figures 6(c) and 6(d)), corresponding to planes (121) and (020), respectively, similar to the maximum diffraction angle of ~33.6 and ~23.6° (2θ) obtained by XRD. Figure 6(e) shows an electron diffraction pattern made on a number of nanoparticles. This result confirmed the crystallinity of the powders previously analyzed by XRD and verified the local crystallinity of NdCoO₃ sample.

(a)

(b)

(c)

(d)

(e)

In some studies, chelating and structure directing agents are employed for controlling the size and shape of the particles. In particular, ethylenediamine is a known chelating agent, which reacts with transition metals yielding coordination compounds [29]. This has been taken advantage of as a strategy for the anisotropic growth of II–VI compound semiconductors such as ZnS, ZnSe, and CdS [33, 34]. In those studies, the ethylenediamine forms complexes with transition metals, which connect each other, and 1D structures like nanowires and nanotubes are obtained through a condensation reaction [34]. Recently, there have been synthesized mixed oxides with trirutile-type structure by “soft” chemistry methods in the presence of ethylenediamine, for example: MgSb₂O₆ nanorods [35], nanostructured ZnSb₂O₆ microbars [36], and interconnected (through neck-like structures) mesoporous CoSb₂O₆ nanoparticles [37]. We found by using our proposed method that NdCoO₃ nanoparticles can be processed with sponge-like morphology to form long chains due to the connectivity between them. The microstructure of these materials is influenced by the amine, which is incorporated and contributes to form inorganic network, acting as a template. Finally subsequently yielding nanocrystals can be tailored in porous adsorption configuration [34]. These morphologies follow the crystallization principles described by Lamer and Dinegar [30, 38].

3.4. AFM Analysis

Figures 7(a)–7(c) present the global topography from NdCoO₃ powders obtained at 700°C by tapping mode AFM. The surface is formed by agglomerates of nanoparticles, which are able to leave spaces in the nanoparticles neighborhood. The scanned area indicates a RMS mean roughness of approximately 1.76 nm. The estimated particle size is about 30 to 150 nm. These results are consistent with those obtained from TEM analysis (Figure 6).

3.5. Gas Sensitivity

Figure 8 shows the sensitivity graph of NdCoO₃ depending on the (a) CO concentration and (b) the operation temperature. At room temperature (25°C), no significant changes were recorded in the electrical resistance of the material, so the sensitivity was zero for all gas concentrations. However, variations at the temperatures 100, 200, and 300°C were detected. Inset in Figure 8(b) shows the changes in the electrical resistance of the material at different temperatures in the presence of CO. In particular, at 100°C, the calculated sensitivity values were 0, 0.01, 0.04, 0.08, 0.13, and 0.20 in the presence of 0, 5, 50, 100, 200, and 300 ppm of CO, respectively; at 200°C, the magnitude of the sensitivity rose to 0, 0.02, 0.07, 0.21, 0.33, and 0.52, respectively, under the same gas concentrations; at 300°C the sensitivity increased to the values of 0, 0.03, 0.10, 0.30, 1.3, and 7.2 with the same CO concentrations. Table 2 summarizes the sensitivity variations in CO at 200 and 300°C. The most accepted mechanism to explain this phenomenon is based on the band bending caused by oxygen adsorption [39]. In this model, the oxygen adsorbed on the surface of the semiconductor captures electrons from the solid, forming the chemisorbed species O^- and O^2-, decreasing the number of the charge carriers [40, 41]. The magnitude of the sensitivity clearly rises with the increase in the gas concentration. This is because the number of CO molecules that react with the chemisorbed oxygen increases, donating electrons to the material’s surface [41]. At higher temperatures (300°C in this case), the more reactive oxygen species (O^-) predominate; therefore, their formation increases the gas-solid interactions in the presence of CO, causing a significant increase in the response. The highest measured sensitivity was 7.2 at 300 ppm of CO and at a temperature of 300°C (Figure 8(a), inset).

(a)

(b)

Figure 9 shows the sensitivity of NdCoO₃ as a function of (a) propane concentration and (b) operation temperature. A similar behavior was previously observed (in CO). Inset in Figure 9(b) shows the changes in the electrical resistance of the material at different temperatures in the presence of propane. The perovskite is sensitive to variations in the concentration of propane, obtaining the values of 0, 0, 0.01, 0.02, 0.03, and 0.04 at concentrations of 0, 5, 50, 100, 200, and 300 ppm at 100°C; at 200°C, the sensitivity increased to 0, 0.003, 0.01, 0.03, 0.05, and 0.07, respectively, at the same gas concentrations; at 300°C the values rose to 0, 0.04, 0.15, 0.63, 5.4, and 94.1, respectively, at the same propane concentrations. Again, the highest sensitivity (94.1) was found at a temperature of 300°C at 300 ppm of the gas (Figure 9(a), inset). Table 3 summarizes the sensitivity variations in propane at 200 and 300°C. The propane detection mechanism has not been deeply studied so far. It has been suggested that the propane molecules react with the chemisorbed O^- oxygen species producing CO₂, water vapor, and a release of electrons to the material’s surface resulting in variations in its electrical resistance and therefore in the sensitivity [42]. Furthermore, the sensitivity of the material decreased when the test gases were removed from the chamber, meaning that the pellets possess a high performance for different gas concentrations at different working temperatures.

(a)

(b)

The gas sensitivity results were compared with similar metal oxides finding that we have succeeded in obtaining a better response. For example, ZnSb₂O₆ microrods showed a sensitivity of ~6.7 and ~1.3 at 250°C in the presence of 300 ppm of CO and propane, respectively [36]. Mesoporous CoSb₂O₆ nanoparticles presented maximum sensitivity values of ~7 (CO) and ~4.8 (propane) at 350°C and a gas concentration of 300 ppm [37]. A sensitivity of ~17 (CO) and ~31 (propane) was reached for LaFeO₃ nanoparticles at 350°C and a gas concentration of 200 and 300 ppm, respectively [43]. On the other hand, undoped SnO₂ and ZnO thin films showed sensitivities of 0.7 and 2.5, respectively, at 300°C and a propane concentration of 300 ppm [44, 45]. The good response of the NdCoO₃ toward gases can be attributed to the microstructure obtained during the synthesis process. It should be mentioned that among the different type of gas sensors (e.g., catalytic combustion, electrochemical, infrared absorption, and thermal conductive), conductometric sensors based on metal oxides have many advantages, such as ease of use, rapid response time, low detection limits, and high sensitivity (verified during this work) [46].

4. Conclusions

In summary, NdCoO₃ perovskite-type nanoparticles were successfully synthesized by the solution method assisted by microwave radiation. This method is a sustainable and alternative route to synthesize NdCoO₃ at a relatively low temperature compared with those used by other synthesis methods, mainly solid-state reactions. The characterization was conducted with X-ray diffraction, scanning and transmission electron microscopy, atomic force microscopy, energy dispersive X-ray spectroscopy, and N₂ adsorption. The nanoparticles, with a high connectivity between them, formed a porous structure sensitive to changes in the concentration of carbon monoxide and propane at different operating temperatures. The sensitivity of the material rose with the increasing of the temperature and the gas concentration. The maximum values of sensitivity were found at 300°C and 300 ppm for both gases. For carbon monoxide, the maximum sensitivity was found of about 7, while for propane the sensitivity markedly increased to a value of 94. In these terms, the perovskite-type NdCoO₃ is a strong candidate to be used as a gas sensor.

Conflicts of Interest

The authors declare that there are no conflicts of interest regarding the publication of this paper.

Acknowledgments

Lorenzo Gildo-Ortiz is thankful to Consejo Nacional de Ciencia y Tecnología (CONACyT) for the received postdoctoral fellowship (2016-3, 41560). Special thanks are due to Miguel Ángel Luna Arias, Leonardo Pérez Manzo, and Darío Pozas Zepeda for their technical assistance during the development of this work.

References

C. N. R. Rao, “World of perovskite oxides: From dielectrics to superconductors,” Physica C: Superconductivity and its Applications, vol. 153-55, no. 2, pp. 1762–1768, 1988.
View at: Publisher Site | Google Scholar
G. Peng, X. Xu, and G. Xu, “Hybrid Organic-Inorganic Perovskites Open a New Era for Low-Cost, High Efficiency Solar Cells,” Journal of Nanomaterials, vol. 2015, Article ID 241853, 10 pages, 2015.
View at: Publisher Site | Google Scholar
H. Du, Y. Li, W. Z. Liang et al., “Impact of NiO_x buffer layers on the dielectric properties of BaTiO₃ thin films on nickel substrates fabricated by polymer assisted deposition,” Journal of Nanomaterials, vol. 2015, Article ID 167569, 7 pages, 2015.
View at: Publisher Site | Google Scholar
A. K. Azad, J. Zaini, P. I. Petra, L. C. Ming, and S. G. Eriksson, “Effect of Nd-doping on structural, thermal and electrochemical properties of LaFe_0.5Cr_0.5O₃ perovskites,” Ceramics International, vol. 42, pp. 4532–4538, 2016.
View at: Google Scholar
Y. Tong, J. Fu, and Z. Chen, “Synthesis, characterization, and NIR reflectance of highly dispersed NiTiO₃ and NiTiO₃/TiO₂ composite pigments,” Journal of Nanomaterials, vol. 2016, Article ID 5464978, 6 pages, 2016.
View at: Publisher Site | Google Scholar
P. H. T. Ngamou and N. Bahlawane, “Chemical vapor deposition and electric characterization of perovskite oxides LaMO₃ (M=Co, Fe, Cr and Mn) thin films,” Journal of Solid State Chemistry, vol. 182, no. 4, pp. 849–854, 2009.
View at: Publisher Site | Google Scholar
M. L. Norton and H.-Y. Tang, “Superconductivity at 32 K in electrocrystallized Ba-K-Bi-O,” Chemistry of Materials, vol. 3, no. 3, pp. 431–434, 1991.
View at: Publisher Site | Google Scholar
H. Abdullah, M. S. Zulfakar, and S. K. Chen, “Effect of Mn-site for Al substitution on structural, electrical and magnetic properties in La_0.67Sr_0.33Mn_1-xAl_xO₃ thin films by sol-gel method,” Journal of Nanomaterials, vol. 2014, Article ID 703072, 9 pages, 2014.
View at: Publisher Site | Google Scholar
A. Baiker, P. E. Marti, P. Keusch, E. Fritsch, and A. Reller, “Influence of the A-site cation in ACoO₃ (A = La, Pr, Nd, and Gd) perovskite-type oxides on catalytic activity for methane combustion,” Journal of Catalysis, vol. 146, no. 1, pp. 268–276, 1994.
View at: Publisher Site | Google Scholar
L. Fu and J.-F. Li, “Preparation and thermoelectric properties of LaCoO3 ceramics,” Key Engineering Materials, vol. 434-435, pp. 404–408, 2010.
View at: Publisher Site | Google Scholar
A. V. Salker, N.-J. Choi, J.-H. Kwak, B.-S. Joo, and D.-D. Lee, “Thick films of In, Bi and Pd metal oxides impregnated in LaCoO₃ perovskite as carbon monoxide sensor,” Sensors and Actuators, B: Chemical, vol. 106, no. 1, pp. 461–467, 2005.
View at: Publisher Site | Google Scholar
S. Ricote, N. Bonanos, F. Lenrick, and R. Wallenberg, “LaCoO₃: Promising cathode material for protonic ceramic fuel cells based on a BaCe_0.2Zr_0.7Y_0.1 $O_{3 - δ}$ electrolyte,” Journal of Power Sources, vol. 218, pp. 313–319, 2012.
View at: Publisher Site | Google Scholar
D. K. Chakrabarty and D. Y. Rao, “Carbon monoxide oxidation on cobaltites of the lanthanides: effect of A-site substitution,” Reaction Kinetics and Catalysis Letters, vol. 33, no. 1, pp. 131–136, 1987.
View at: Publisher Site | Google Scholar
A. Y. Zuev, V. V. Sereda, and D. S. Tsvetkov, “Defect structure and defect-induced expansion of doped perovskite La_0.7Sr_0.3Co_0.9Fe_0.1 $O_{3 - δ}$ ,” International Journal of Hydrogen Energy, vol. 39, no. 36, pp. 21553–21560, 2014.
View at: Publisher Site | Google Scholar
J. C. Ruiz-Morales, J. Canales-Vázquez, J. Peña-Martínez, D. Marrero-López, J. T. S. Irvine, and P. Núñez, “Microstructural optimisation of materials for SOFC applications using PMMA microspheres,” Journal of Materials Chemistry, vol. 16, no. 6, pp. 540–542, 2006.
View at: Publisher Site | Google Scholar
C. J. Belle, A. Bonamin, U. Simon et al., “Size dependent gas sensing properties of spinel iron oxide nanoparticles,” Sensors and Actuators, B, vol. 160, no. 1, pp. 942–950, 2011.
View at: Publisher Site | Google Scholar
D. D. Athayde, D. F. Souza, A. M. A. Silva et al., “Review of perovskite ceramic synthesis and membrane preparation methods,” Ceramics International, vol. 42, pp. 6555–6571, 2016.
View at: Publisher Site | Google Scholar
E. Matijević, “Preparation and properties of uniform size colloids,” Chemistry of Materials, vol. 5, no. 4, pp. 412–426, 1993.
View at: Publisher Site | Google Scholar
J. W. Fergus, “Perovskite oxides for semiconductor-based gas sensors,” Sensors and Actuators, B: Chemical, vol. 123, no. 2, pp. 1169–1179, 2007.
View at: Publisher Site | Google Scholar
L. Malavasi, C. Tealdi, G. Flor et al., “NdCoO₃ perovskite as possible candidate for CO-sensors: thin films synthesis and sensing properties,” Sensors and Actuators, B: Chemical, vol. 105, no. 2, pp. 407–411, 2005.
View at: Publisher Site | Google Scholar
H. J. Jung, J.-T. Lim, S. H. Lee, Y.-R. Kim, and J.-G. Choi, “inetics and mechanisms of CO oxidation on ${N d}_{1 - x} {S r}_{x} {C o O}_{3 - y}$ catalysts with static and flow methods,” Journal of Physical Chemistry, vol. 100, no. 24, pp. 10243–10248, 1996.
View at: Publisher Site | Google Scholar
C. R. Michel, E. Delgado, G. Santillán, A. H. Martínez, and A. Chávez-Chávez, “An alternative gas sensor material: synthesis and electrical characterization of SmCoO₃,” Materials Research Bulletin, vol. 42, no. 1, pp. 84–93, 2007.
View at: Publisher Site | Google Scholar
K. Wetchakun, T. Samerjai, and N. Tamaekong, “Semiconducting metal oxides as sensors for environmentally hazardous gases,” Sensors and Actuators B: Chemical, vol. 160, no. 1, pp. 580–591, 2011.
View at: Publisher Site | Google Scholar
H. Wang, G. Li, and L. Li, “Molten-salt-mediated synthesis and low-temperature electrical conduction of LnCoO₃ (Ln = Pr, Nd, Sm, and Gd),” Journal of Alloys and Compounds, vol. 612, pp. 227–232, 2014.
View at: Publisher Site | Google Scholar
H. Hashimoto, T. Kusunose, and T. Sekino, “Influence of ionic sizes of rare earths on thermoelectric properties of perovskite-type rare earth cobalt oxides RCoO₃ (R = Pr, Nd, Tb, Dy),” Journal of Alloys and Compounds, vol. 484, no. 1-2, pp. 246–248, 2009.
View at: Publisher Site | Google Scholar
C. Tealdi, M. S. Islam, C. A. J. Fisher, L. Malavasi, and G. Flor, “Defect and transport properties of the NdCoO₃ catalyst and sensor material,” Progress in Solid State Chemistry, vol. 35, no. 2-4, pp. 491–499, 2007.
View at: Publisher Site | Google Scholar
V. R. Choudhary and K. C. Mondal, “CO₂ reforming of methane combined with steam reforming or partial oxidation of methane to syngas over NdCoO₃ perovskite-type mixed metal-oxide catalyst,” Applied Energy, vol. 83, no. 9, pp. 1024–1032, 2006.
View at: Publisher Site | Google Scholar
C. R. Michel, A. H. Martínez, F. Huerta-Villalpando, and J. P. Morán-Lázaro, “Carbon dioxide gas sensing behavior of nanostructured GdCoO₃ prepared by a solution-polymerization method,” Journal of Alloys and Compounds, vol. 484, no. 1-2, pp. 605–611, 2009.
View at: Publisher Site | Google Scholar
V. V. Gorbunov, A. A. Shidlovskii, and L. F. Shmagin, “Combustion of transition-metal ethylenediamine nitrates,” Combustion, Explosion, and Shock Waves, vol. 19, no. 2, pp. 172-173, 1983.
View at: Publisher Site | Google Scholar
L. Gildo-Ortiz, H. Guillén-Bonilla, and J. Santoyo-Salazar, “Low-temperature synthesis and gas sensitivity of perovskite-type LaCoO₃ nanoparticles,” Journal of Nanomaterials, vol. 2014, Article ID 164380, 8 pages, 2014.
View at: Publisher Site | Google Scholar
O. Mihai, D. Chen, and A. Holmen, “Chemical looping methane partial oxidation: the effect of the crystal size and O content of LaFeO₃,” Journal of Catalysis, vol. 293, pp. 175–185, 2012.
View at: Publisher Site | Google Scholar
Y. Yamada, K. Yano, D. Hong, and S. Fukuzumi, “LaCoO₃ acting as an efficient and robust catalyst for photocatalytic water oxidation with persulfate,” Physical Chemistry Chemical Physics, vol. 14, no. 16, pp. 5753–5760, 2012.
View at: Publisher Site | Google Scholar
Z.-X. Deng, C. Wang, X.-M. Sun, and Y.-D. Li, “Structure-directing coordination template effect of ethylenediamine in formations of ZnS and ZnSe nanocrystallites via solvothermal route,” Inorganic Chemistry, vol. 41, no. 4, pp. 869–873, 2002.
View at: Publisher Site | Google Scholar
X. Wang and Y. Li, “Solution-based synthetic strategies for 1-D nanostructures,” Inorganic Chemistry, vol. 45, no. 19, pp. 7522–7534, 2006.
View at: Publisher Site | Google Scholar
H. Guillén-Bonilla, M. Flores-Martínez, V.-M. Rodríguez-Betancourtt et al., “A novel gas sensor based on MgSb₂O₆ nanorods to indicate variations in carbon monoxide and propane concentrations,” Sensors (Switzerland), vol. 16, no. 2, article 177, pp. 1–12, 2016.
View at: Publisher Site | Google Scholar
H. Guillen-Bonilla, V.-M. Rodríguez-Betancourtt, J.-T. Guillén-Bonilla et al., “CO and C₃H₈ sensitivity behavior of zinc antimonate prepared by a microwave-assisted solution method,” Journal of Nanomaterials, vol. 2015, Article ID 979543, 8 pages, 2015.
View at: Publisher Site | Google Scholar
H. Guillén-Bonilla, L. Gildo-Ortiz, M. L. Olvera-Amador et al., “Sensitivity of mesoporous CoSb₂O₆ nanoparticles to gaseous CO and C₃H₈ at low temperatures,” Journal of Nanomaterials, vol. 2015, Article ID 308465, 9 pages, 2015.
View at: Publisher Site | Google Scholar
V. K. Lamer and R. H. Dinegar, “Theory, production and mechanism of formation of monodispersed hydrosols,” Journal of the American Chemical Society, vol. 72, no. 11, pp. 4847–4854, 1950.
View at: Publisher Site | Google Scholar
C. Wang, L. Yin, L. Zhang, D. Xiang, and R. Gao, “Metal oxide gas sensors: sensitivity and influencing factors,” Sensors, vol. 10, no. 3, pp. 2088–2106, 2010.
View at: Publisher Site | Google Scholar
S. C. Chang, “Oxygen chemisorption on tin oxide: correlation between electrical conductivity and EPR measurements,” Journal of vacuum science & technology, vol. 17, no. 1, pp. 366–369, 1979.
View at: Publisher Site | Google Scholar
M. Siemons and U. Simon, “High throughput screening of the sensing properties of doped SmFeO₃,” Solid State Phenomena, vol. 128, pp. 225–236, 2007.
View at: Publisher Site | Google Scholar
V. K. Jayaraman, A. Maldonado Álvarez, and M. De la Luz Olvera Amador, “A simple and cost-effective zinc oxide thin film sensor for propane gas detection,” Materials Letters, vol. 157, Article ID 18958, pp. 169–171, 2015.
View at: Publisher Site | Google Scholar
L. Gildo-Ortiz, J. Reyes-Gómez, J. M. Flores-Álvarez et al., “Synthesis, characterization and sensitivity tests of perovskite-type LaFeO₃ nanoparticles in CO and propane atmospheres,” Ceramics International, vol. 42, no. 16, pp. 18821–18827, 2016.
View at: Publisher Site | Google Scholar
H. Gómez-Pozos, J. L. González-Vidal, G. A. Torres, M. de la Luz Olvera, and L. Castañeda, “Physical characterization and effect of effective surface area on the sensing properties of tin dioxide thin solid films in a propane atmosphere,” Sensors, vol. 14, no. 1, pp. 403–415, 2013.
View at: Publisher Site | Google Scholar
H. Gómez-Pozos, J. L. González-Vidal, and G. A. Torres, “Chromium and ruthenium-doped zinc oxide thin films for propane sensing applications,” Sensors, vol. 13, no. 3, pp. 3432–3444, 2013.
View at: Publisher Site | Google Scholar
G. Korotcenkov, “Metal oxides for solid-state gas sensors: what determines our choice?” Materials Science and Engineering B: Advanced Functional Solid-State Materials, vol. 139, no. 1, pp. 1–23, 2007.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2017 Lorenzo Gildo-Ortiz et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

1599

Downloads

1230

Citations

Journal of Nanomaterials

Facile Synthesis, Microstructure, and Gas Sensing Properties of NdCoO3 Nanoparticles

Abstract

1. Introduction

2. Experimental Procedures

2.1. NdCoO3 Synthesis

2.2. Characterization of NdCoO3 Powders

2.3. Gas Sensitivity Tests

3. Results and Discussion

3.1. XRD Analysis

3.2. SEM Analysis and N2 Adsorption

3.3. TEM Analysis

3.4. AFM Analysis

3.5. Gas Sensitivity

4. Conclusions

Conflicts of Interest

Acknowledgments

References

Copyright

Facile Synthesis, Microstructure, and Gas Sensing Properties of NdCoO₃ Nanoparticles

2.1. NdCoO₃ Synthesis

2.2. Characterization of NdCoO₃ Powders

3.2. SEM Analysis and N₂ Adsorption