Boehmite and Akaganeite 1D and 2D Mesostructures: Synthesis, Growth Mechanism, Ageing Characteristics and Surface Nanoscale Roughness Effect on Water Purification

Kaledin, Leonid A.; Tepper, Fred; Vesga, Yuly; Kaledin, Tatiana G.

doi:https://doi.org/10.1155/2019/9516156

Journal of Nanomaterials

On this page

Abstract Introduction Materials and Methods Results and Discussion Conclusions Data Availability Conflicts of Interest References Copyright Related Articles

Special Issue

Smart Nanostructured Materials: From Molecular Self-Assembly to Advanced Applications

View this Special Issue

Research Article | Open Access

Volume 2019 | Article ID 9516156 | https://doi.org/10.1155/2019/9516156

Boehmite and Akaganeite 1D and 2D Mesostructures: Synthesis, Growth Mechanism, Ageing Characteristics and Surface Nanoscale Roughness Effect on Water Purification

Leonid A. Kaledin,¹Fred Tepper,¹Yuly Vesga,¹and Tatiana G. Kaledin¹

Guest Editor: Pietro Calandra

Received23 Jul 2019

Accepted21 Sept 2019

Published06 Nov 2019

Abstract

The role of surface nanoscale roughness on the charging behavior of nanostructured γ-AlOOH (Boehmite) and β-FeOOH (Akaganeite)/γ-AlOOH (Boehmite) mesostructures deposited onto siliceous substrates has been investigated. Two-dimensional (2D) quantum-sized and one-dimensional (1D) nanometer size γ-AlOOH (Boehmite) structures and 2D atomically-thin β-FeOOH (Akaganeite) nanobelts with a mean width of approximately 10 nm were deposited onto siliceous substrates in aqueous processes at moderate temperatures. Low cost and large scale manufacturing of siliceous substrates coated with 2D and 1D γ-AlOOH (Boehmite) crystallites of 2.7 ± 0.5 nm in diameter, with an average length of 2.9 ± 0.9 nm and 250 ± 50 nm, respectively, that were further functionalized with atomically thin 2D β-FeOOH (Akaganeite) nanobelts was demonstrated. Zeta potentials of surfaces have been characterized by direct measurement of streaming potentials in NaCl aqueous electrolyte. A model explaining the pH dependent behavior of the zeta potential was proposed. The isoelectric point values of rough nanostructured surfaces are three pH units higher as compare to the flat crystalline γ-AlOOH (Boehmite) and β-FeOOH (Akaganeite) surfaces, resulting in a high removal efficacy of submicron particles from aqueous suspension by the surfaces with combined microscale and nanoscale structures. This suggests the existence of a coupling electrokinetic effect of the local electrical double layer (EDL) fields with the local flow fields.

1. Introduction

Coating sand and diatomaceous earth (DE) particles with aluminum and ferrous hydroxides changes the zeta potential of filtration media from negative to positive in the pH range from 3 to 11 and from 3 to 10, respectively. As a result, those surface modified media greatly improve removal efficacy of submicron particles [1–8]. The role of the electrical double layer (EDL) and van der Waals (VDW) forces in particle deposition is often viewed in terms of Derjaguin–Landau–Verwey–Overbeek (DLVO) theory [9, 10], which was developed for smooth, homogeneous particles with ideal geometries and with no EDL overlap. The influence of surface roughness of filter media on streaming potential measurements is well documented [11]. The samples made from the same material with different surface roughness, measured by the same method, in the same device showed zeta potential values significantly different from each other, while the isoelectric point (IEP) values were identical between the measurements [11]. Moreover, the velocity profiles for two different spots along the surface of a multifilament fabric showed circulation pattern between two yarns during the streaming potential measurement. The general impact of roughness is to amplify the long-range behavior of noncontact DLVO forces with the approximate amplification factor of exponential force between rough and smooth surfaces exp(σ_roughness²/λ_Debye²), where σ_roughness is the mean roughness [12]. Furthermore, the influence of particle shape and particle size on the zeta potential of colloidal suspensions is well known for the case of ultrapure silica powders where the authors found that the maximum zeta potential occurs for particle size ranging between 0.1 μm and 1 μm [13].

A variety of analytical and numerical models have been developed to describe the pressure-driven flow over heterogeneous surfaces. The vast majority of these models assume that the local electric double layer (EDL) field is independent of the flow field [14–17]. However, for pressure-driven flow over a surface with heterogeneous patches, the local EDL fields are not uniform. This means that they are more different above a patch than in the region between the patches. This irregularity produces distortions in the equilibrium electrostatic field. Consequently, the electrostatic potential can alter the value of the zeta potential from its expected value over a surface with uniformly smeared surface under conditions of moderate surface charge [18–21]. The characteristic symptom of field distortion is the generation of flow velocities in all three coordinate directions, including a circulation pattern perpendicular to the main flow axis.

The present study of 1D and 2D nanostructures was motivated by three primary considerations. The first one was to present the characterization of the surface’s zeta potentials by direct measurement of streaming potentials in NaCl aqueous electrolyte. The isoelectric point values of rough nanostructured surfaces are three pH units higher as compare to the flat crystalline γ-AlOOH and β-FeOOH surfaces, resulting in a high removal efficacy for different classes of contaminants such as metal ions [2], small colloidal particles [6–8], as well as biological particles like virus, bacteria and cyst [1, 2]. The second motivation was to develop a model that explains the pH dependent behavior of the zeta potential based on contributions from the three morphological planes of different chemical composition existing at siliceous particles coated with 2D and 1D γ-AlOOH crystallites: γ-AlOOH face and edge layers, and silica basal layer which are complex oxides of the two constituents: γ-AlOOH and SiO₂. The third one was provided by ageing characteristics of the 2D, 1D γ -AlOOH and 2Dβ-FeOOH/2Dγ-AlOOH crystallites, which showed no degradation in performance (i.e., TEM, particle size distribution, etc.) over periods of more than seven (2D materials) and fourteen (1D materials) years. This is a very important finding since siliceous substrates coated with 1D arrays is manufactured and sold as non-woven media by Ahlstrom Filtration LLC under the tradename Disruptor™. Siliceous substrates coated with the 2Dγ-AlOOH and with a combination of 2Dγ-AlOOH and 2Dβ-FeOOH crystallites is manufactured by Argonide Corporation in large scale multi-tonnage processes.

2. Materials and Methods

2.1. Transmission Electron Microscopy (TEM) Study

The TEM images (Figure 1(a), 1(b)) were recorded on the JEOL JEM2010 TEM at 200 kV accelerating voltage. The high resolution TEM (HRTEM) images (Figure 1(c)-1(f)) were recorded on the Tecnai F30 at 300 kV accelerating voltage. It is important to note that boehmite bulk γ-AlOOH material has melting temperature over 1000°C (T_melt~2050°C after several phase transformations, i.e., , , and ) [22]. It is also chemically inert and exhibits no decomposed surface layer in air, giving it the best chances of having 2D counterparts stable at room temperature [23]. Furthermore, it appears that the TEM high energy electrons needed to get enough resolution do not cause apparent damage to the sample.

(a)

(b)

(c)

(d)

(e)

(f)

Figure 1

TEM characterization of 2D and 1D γ-AlOOH and 2Dβ-FeOOH crystallites: (a) TEM image of the 1Dγ-AlOOH crystallites [6]; (b) TEM image of the 1Dγ-AlOOH crystallites attached to a 0.6 μm diameter microglass fiber [6]; (c) HRTEM image of the edge coverage of 5 μm diameter DE particle by the 2Dγ-AlOOH crystallites with atomic resolution. The separation of ≈0.24 nm is in agreement with the bulk boehmite lattice parameter d₍₀₂₀₎ = 0.242(4) nm [24]; (d) HRTEM image of the surface coverage of 5 μm diameter DE particle by the 2Dγ-AlOOH crystallites; (e), (f) HRTEM images of the surface coverage of 5 μm diameter DE particle by 2D. γ-AlOOH crystallites further functionalized with 2D atomically thin nanobelts of akaganeite . β-FeOOH crystallites.

2.2. Synthesis of 1D γ-AlOOH Crystals

The synthesis of one-dimensional (1D) 2.7 ± 0.5 nanometer diameter 250 ± 50 nm long γ-AlOOH nanofibers seen in Figure 1(a) was accomplished via reaction of aluminum powder with alkaline water: [6].

The synthesis of one-dimensional (1D) nanometer-sized γ-AlOOH atomic crystals adhered to siliceous and cellulosic substrates was accomplished via reaction (1) where aluminum powder reacts with alkaline water [6]. Amounts of 0.5 g of aluminum metal powder and 1.5 g of amorphous borosilicate glass microfiber with average diameter of 0.6 μm were dispersed in 0.5 L liter of RO water and were reacted in a 1 L stainless steel pot in the presence of 1 mL of 10 M NaOH at ambient pressure. The suspension was heated to its boiling point at ambient pressure while mixing with an air-driven mixer equipped with 5 cm diameter impeller at 300 RPM. The suspension was cooled down to 40-50°C, neutralized with 10% sulfuric acid to pH 6-8. The non-woven paper-like mat were formed by conventional wet-laid paper making technology. Nitrogen BET (Brunauer, Emmett, Teller) specific surface area of dry sample of 1Dγ-AlOOH nanostructure (Figure 1(a)) was [6].

2.3. Synthesis of 2D Quantum-Sized γ-AlOOH Crystals Adhered to Siliceous Substrates

Synthesis of 2D quantum-sized γ-AlOOH crystals adhered to siliceous substrates was accomplished via the same reaction (equation (1)) of aluminum powder in the presence of siliceous substrate with alkaline water. The step-by step descriptions of the 2D quantum-sized γ-AlOOH crystals synthesis adhered to siliceous substrate are reported in Ref. [8] The siliceous powder, in form of diatomaceous earth (DE) was dispersed in 4 liters of RO water and allowed to react with 17.5 g of micron size aluminum powders in the presence of 40 mL of 10 M NaOH at ambient pressure. It was heated to boiling point while mixing with an air-driven mixer at 300 RPM. Then, the suspension was cooled down to 40-50°C and neutralized to pH 6-8 with 10% sulfuric acid. Decantation was allowed. Then, it was dried overnight at 100°C. Finally, the media was crushed and sieved through a 170-mesh sieve. Nitrogen BET specific surface area of dry sample of 5 μm diameter diatomaceous earth (DE) particles coated with quantum-sized 2D γ-AlOOH crystals of 2.7 ± 0.5 nm in diameter and 2.9 ± 0.9 nm long (Figure 1(c), 1(d)) increased from =51 m²/g to =69 m²/g. This suggests formation of additional surfaces on the substrate as seen in Figures 1(c), 1(d) and in a sketch of Figure 2(a).

(a)

(b)

2.4. Synthesis of 1D Nanometer-Sized γ-AlOOH Crystals Adhered to Siliceous Substrate

The synthesis of 1D 2.7 ± 0.5 nanometer diameter γ-AlOOH nanofibers seen in Figure 1(a) adhered to siliceous substrate (Figure 1(b)) was accomplished via the same reaction (equation (1)) of aluminum powder with alkaline water in the presence of the substrate [6]. The non-woven paper-like mat was formed by conventional wet-laid paper making technology.

2.5. Synthesis of Atomically Thin 2Dβ-FeOOH Nanobelt Crystals Adhered to Siliceous Substrates Preliminary Coated with 2D Quantum-Sized γ-AlOOH Crystals

The step-by step description of the 2D quantum-sized β-FeOOH crystals synthesis adhered to siliceous substrate were initially reported in Ref. [8] The BET (Brunauer, Emmett, Teller) value due to addition of ferric chloride increased by 42% from to . This suggests formation of additional surfaces on the substrate as seen in Figure 1(f) (insets 1-3) and in a sketch of Figure 2(b) of atomically thin nanobelts oriented parallel and normal to the substrate (insets 1 and 3) and under an angle (inset 2) with electron beam either perpendicular (inset 1), parallel (inset 3), or under angle (inset 2) to the nanobelt.

3. Results and Discussion

3.1. High Resolution TEM Analysis

Representative samples of 2D and 1D materials obtained by the procedures described above were investigated further by HRTEM. Figures 1(c), 1(d) show examples of the atomic-resolution HRTEM images of 2Dγ-AlOOH crystallites. Thickness of the 2Dγ-AlOOH crystallites was estimated to be 2.9 ± 0.9 nm based on the HRTEM images (Figures 1(c), 1(d)). When the lateral dimensions of 2Dγ-AlOOH structure are approximated by a circle, they are 7 and 10 times greater than the boehmite a and c unit cell dimensions, correspondently (Figure 2, insert). This is consistent with boehmite crystal growth, which occurs mainly along the a–c plane where atomic in-plane bonds are stronger than the weak, van der Waals (VDW)-type, interlayer bond along the b-axis [24]. Assuming that the crystals seen in Figures 1(c), 1(d) are fully dense γ-AlOOH cylinders (Figure 2(a)) with diameter d = 2.7 ± 0.5 nm that covers a fraction θ = 0.082 ± 0.016 of the silica surface (Figure 1(d)) with nitrogen BET (Brunauer, Emmett, Teller) specific surface area values of and , the ratio translates into l = 2.9 ± 0.9 nm implying that the average length l of the 2Dγ-AlOOH crystals seen in Figures 1(c), 1(d) is 2-3 times of boehmite cell dimension b = 1.212(1) nm [24]. Figure 2(a) shows a sketch of 2Dγ-AlOOH crystallites comprising from two or three atomically thin layers deposited onto siliceous substrate linked together by the weak van der Waals (VDW)-type interlayer bond along the b-axis.

The width of 2D nanobelt β-FeOOH crystals attached to silica surface is 9-10 times of the akaganeite a or c unit cell dimension (see Figures 1(e), 1(f) between white arrows). This is consistent with akaganeite crystal growth, which occurs mainly along the a-c plane in both directions where atomic in-plane bonds are stronger than the weak van der Waals (VDW)-type interlayer bonds along the b-axis.

Such lateral 2D structures on silica surface would not increase available BET (Brunauer, Emmett, Teller) surface area. Yet, the BET surface area increased by 42% from =69 m²/g to =98 m²/g. This suggests the formation of additional surfaces on siliceous substrate as seen in Figure 1(f) (insets 1-3). Single-, double- or few-layer crystallites could be identified in an optical and TEM microscopes due to their different contrast that increases with increasing number of layers [25]. Further, assuming that these atomically thin nanobelts are fully dense β-FeOOH parallelepipeds that covers a fraction of silica surface of θ = 0.03 ± 0.02 (Figures 1(e), 1(f)), the BET specific surface area value would increase by: where δ is the thickness of 2D platelets approximately equals to a or c akaganeite cell dimensions of 1 nm. Such a model explains a 42% increase in BET surface area from =69 m²/g to .

3.2. Zeta Potentials of 2D and 1D γ-AlOOH and 2D γ-AlOOH/β-FeOOH Crystallites Deposited onto Siliceous Particles

It was found that siliceous particles coated with 2D and 1D γ-AlOOH crystallites are positively charged in aqueous solution with zeta potential ≥40 mV [26] at γ-AlOOH loading greater than 15 weight percent (wt%) [1] as compared to the negatively charged character of the bare siliceous substrates (zeta potential ≤ -70 mV) [1]. Figure 3 shows zeta potential of siliceous powder coated with 2D and 1D γ-AlOOH and with 2D β-FeOOH/2D γ-AlOOH crystallites as a function of pH. The point of zero charge (pH_PZC) describes the condition when the electrical charge density on a surface is zero [27]. The pH_PZC values of siliceous particles coated with 1D, 2D γ-AlOOH, and 2D β-FeOOH/2D γ-AlOOH were determined to be 11.6 ± 0.2 for 1D γ-AlOOH [26], 11.4 ± 0.2 for 2D γ-AlOOH [26], and 10.5 ± 0.3 for 2D β-FeOOH/2D γ-AlOOH (see Figure 3(a)). Those values are three pH units higher as compare to the average values for flat crystalline γ-AlOOH [26, 27] and β-FeOOH [27] surfaces. Borghi et al. [28] observed a remarkable reduction by several pH units of the isoelectric point (IEP) on rough nanostructured surfaces, with respect to flat crystalline rutile TiO₂. In order to explain the observed behavior of IEP, Borghi et al. [28] considered the roughness-induced self-overlap of the electrical double layers as a potential source of deviation from the trend expected for flat surfaces. Contrary to the acidic behavior of nanostructured surfaces crystalline rutile (Lewis acid sites), siliceous particles coated with quantum size 2D, 1D γ-AlOOH and 2Dβ-FeOOH crystallites behave preferentially as basic loci [1].

(a)

(b)

In general, the total charge per unit surface area in the diffuse layer around a particle can be evaluated with the use of the Graham equation (see Eq. (6).3.27 of Ref. [17]). For a symmetric electrolyte (z₊ = - z_- = z) in water at 25°C, the Graham equation is reduced to (see equation (6).3.28 of Ref. [17]): where σ_d is in μC/cm² and ψ_d measures the electrostatic potential at, or very near to, the beginning of the diffuse double layer (i.e., ψ_d ≈ ζ) in volts and c is the ionic concentration in mol/L.

In the case of small potentials (ζ < 100 mV [29]) and a monovalent electrolyte (z₊ = -z_- = z = 1), equation (4) can be approximated with good precision to equation (5):

This equation allows to estimate the charge density, σ_d, at the beginning of the diffuse double layer as a function of pH. A satisfactory model (e.g., a triple layer model (see Figure 6.10.3 of Ref. [17]) of the interface should reproduce both the σ₀/pH, where σ₀ is the surface charge density on the particle, and ζ/pH curves as seen in Figure 3(b)).

Three morphological planes of different chemical composition exist at siliceous particles coated with 2D and 1D γ-AlOOH crystallites: γ-AlOOH face and edge layers, and siliceous basal layer which are complex oxides of the two constituents γ-AlOOH and SiO₂. Following a model proposed by Stumm for kaolinite [30], we can distinguish the following type of surface ligands at the silica and boehmite face and edge surfaces: i) = MOH groups such as Al-OH-Al groups at the boehmite face surface, Si-O-Si groups at the siliceous basal surface, and = AlOH and/or = SiOH groups at the boehmite edge surface; ii) XO^- group such as (Al-O-Si)^- where Al is situated at the boehmite edge surface and Si is on the siliceous basal surface (Figure 2(a)). Based on electron microscopic studies of a negative gold sol attachment to a kaolinite edge surface performed by Thiessen [31], van Olphen has shown a pH-dependent charge at the edges of the kaolinite platelets (see Figure 22 of Ref. [32]). The conclusion was that the double-layer structure is challenging due to the fact that two crystallographically different surfaces are carrying a different type of double layers that under certain condition can have opposite signs. Measurements of the electric double layer (EDL) properties of CaF₂ [33], α-Al₂O₃ (Sapphire) [34], and TiO₂ (Rutile) [35] indicated significant differences (up to 2 pH units) between the isoelectric points in various crystallographic orientations of surfaces.

The pH_PZC is the same as the isoelectric point (IEP) if there is no specific adsorption of other ions than the potential determining H⁺/OH⁻ at the surface. At this point, the portion of the charge due to H⁺ and OH^- or their complexes becomes zero. At pH 11.4, the pH_PZC and the proton density, _H, on 2D γ-AlOOH face surface are zero (Figure 3(b)). In the present work, we assumed that the boehmite edge surface is protonated at the same level in the pH range from 3.0 to 10.5 (broken horizontal line in Figure 3(b)) and the protonation is proportional to the zeta potential at pH 10.5 and is equal to the surface charge, _H = ^{edge, pH = 10.5}. The surface charge of the edge surface in the pH range from 10.5 to 11.4 was estimated as:

The excess proton density _H, which is equal to the surface charge, ₀, at the surface hydroxyl group is displayed as a function of pH. Surface protonation of the 2D γ-AlOOH crystallites is interpreted as a successive protonation of the two distinct types of OH group localized on boehmite face and edge surfaces. Under this assumption, we estimated the pH_PZC values of the edge surface at approximately 11.4 ± 0.2 and boehmite face surface at approximately 9.5 ± 0.5. The latter value is within accuracy with an average value of 8.7 ± 0.9 obtained for smooth boehmite surfaces [26, 27] and the former value is within accuracy with the pH_PZC of aluminum hydroxide γ-AlOOH adjuvant of 11.4 [36] that is morphologically and geometrically similar to the nanofibers seen in Figure 1(a).

3.3. Removal Efficacy of Submicron Particles as a Function of pH and Electrolyte Ionic Strength

Table 1 shows initial removal efficacy of biological particles from aqueous solution associated with pressure-driven flow through micrometer size pores of either 2Dγ-AlOOH/DE or 2Dβ-FeOOH/2Dγ-AlOOH/DE particles packed into a 3-mm deep precoat [37] or through a 1Dγ-AlOOH/microglass non-woven filter media [6, 7].

Table 1 displays that siliceous particles coated with 2D and 1D γ-AlOOH and 2Dβ-FeOOH/2Dγ-AlOOH/DE structures resulted in a high removal efficacy (in all cases greater than 99.9%) of biological particles regardless of zeta potential value in the range from 15 mV to 56 mV. Estimations show that Brownian displacement does not play significant role in removal efficacy of micron size Raoultella Terrigena (RT) bacteria in a 3 mm deep 2D γ-AlOOH/DE and 2D β-FeOOH/2D γ-AlOOH/DE precoats with mean flow pore size of d_mean-flow = 24 ± 4 μm for diatomaceous earth (DE) with average particle size of 80 μm [2]. When the Stokes–Einstein equation [38] is applied to a spherical particle suspended in water, it produces an estimated root-mean-square displacement during a contact time of 4.5 s in a 3-mm deep precoat of only 1.8 μm in the case of RT bacteria. Furthermore, the electrostatic attraction should not play significant role in the case of RT bacteria due to highly efficient shielding by the electric double layer (EDL) layer with Debye length as short as 1.6 Å in the 3.4 M NaCl electrolyte (Table 1). Anisotropic characteristics of EDL layer have been observed in numerous material systems (see, e.g., Refs. [34–30]). For instance, in recent study of dendrimer-biomembrane interaction [29], the self-assembly processes of a mixture of charged polyamidoamine (PAMAM) dendrimers and dipalmitoylphosphatidylcholine (DPPC) lipids were investigated by means of zeta potential analysis, Raman and X-ray scattering. Zwitterionic DPPC liposomes showed substantially different behaviors during their interaction with negatively charged sodium carboxylate terminated (COO^– Na⁺) dendrimers or positively charged amino terminated (− NH₂) dendrimers [29].

3.4. Removal Efficacy of Bio Particles by a Mixture of Opposively Charged Particles

In this section, we will discuss the 3D flow structure associated with pressure-driven flow through micrometer size pores of a mixture of equal but opposite charged particles packed into a 3-mm deep precoat [37]. The surfaces of diatomaceous earth (DE) and 2D γ-AlOOH/DE particles have similar but opposite values of zeta potentials [1]. In such a case, there is an excess of positive ions over the DE surface, but negative ions dominate over the 2D γ-AlOOH/DE surface to balance out the positive surface charge. The difference in the surface potential results in an electrostatic potential gradient within the local electric double layer (EDL) fields near the transition zone between the two regions. The presence of this potential gradient results in a body force on the microbes and/or ions in the double layer; however, in this case, an opposite body force is applied to the negative ions over the positively charged particle. As a result, the net body force over the region is zero and the circulation velocity perpendicular to the main flow becomes negligible [18–21]. For the purpose of this study, it was selected that 2D γ-AlOOH/DE and DE particles have equal average size of d = 80 ± 3 μm. It was assumed to be packed in simple cubic cell with particles only at the corners as seen in Figure 4(a), 4(b). DE particles were mixed with 2D γ-AlOOH/DE particles with DE content in the mix of 10-, 25-, 50-, and 75-wt% and formed a 3-mm deep precoats (Δ_thickness = 3 mm). Assuming a cubic cell packing, the number of layers is estimated as N_layers = Δ_thickness/d_average~38.

Table 2 shows removal efficacy of MS2 virus and Raoultella Terrigena (RT) bacteria by 3 mm precoats of diatomaceous earth (DE) particles coated with 2D γ-AlOOH crystallites mixed with uncoated DE particles at a flow velocity of 0.67 mm/s, neutral pH 7 and ionic strength of 2 ± 1 μM [1]. The mean flow pore diameter of the precoat layer was determined to be 24 ± 4 μm [2]. Table 2 also provides experimental evidence of a behavior when a 3 mm precoat is losing adsorption properties of the 2D γ-AlOOH/DE at much faster rate than one can expect based on the weight fraction of DE in the mix. For example, for a 50/50-wt% mix, one can expect a reduction in adsorption efficacy by a factor of two or by log₁₀(1/2) = -0.3 based on the 2D γ-AlOOH/DE fraction in the mix while experimental reductions are 3.5 ± 1.0 logarithm reduction value (LRV) for MS2 virus and greater than 4.7 LRV for RT bacteria (Table 2). This is consistent with the case when at least one of the neighboring particles on the side of the cube perpendicular to the flow direction has opposite sign of the surface charge, i.e., -|σ₂| for DE than the other neighboring particles, i.e., + |σ₁| for 2D γ-AlOOH/DE ceasing the circulation pattern in that pore involving four neighboring particles. That is, one DE particle is cancelling out high removal efficacy of three 2D γ-AlOOH/DE particles situated on the same side of the cube perpendicular to the flow direction (Figure 4(b)).

The average number of layers in a pore formed by a group of four 2D γ-AlOOH/DE particles with no diatomaceous earth (DE) particle in the group decreases rapidly as DE loadings in the mix increases. Finally, Table 2 presents average number of layers in a pore of the precoat layer formed by a group of four 2D γ-AlOOH/DE particles with no DE particle in the group together with the average layer thickness in the 3-mm precoat formed by four neighboring 2D γ-AlOOH/DE particles with no DE particle in the group.

3.5. Removal Efficacy of Bioparticles due to Particle Interactions

Another important reason why siliceous particles coated with 2D and 1D γ-AlOOH and 2D β-FeOOH/2D γ AlOOH/DE structures resulted in a high removal efficacy of biological particles is their strong electropositive charge properties when dispersed in polar liquids. These media’s structure assemblies create a strong field that extends from the alumina surface into an aqueous dispersive medium, which is many orders (>4) greater than the one predicted by the Derjaguin–Landau–Verwey–Overbeek (DLVO) theory, especially at high ionic strength [12]. It is important to note that the DLVO theory was developed for smooth, homogeneous particles with ideal geometries and with no EDL overlap [9, 10]. For this reason, the stronger field extension observed in the media can be simply explained by the general impact of roughness, which is to amplify the long-range behaviour of noncontact DLVO forces with the amplification factor of exponential force between rough and smooth surfaces [12]. The adsorption mechanism is mainly influenced by the combination of their inherent charge and the acquired induced polarization charge, rather than by physical entrapment based on particle size. 2D and 1D γ-AlOOH and 2D β-FeOOH/2D γ AlOOH/DE structures have a high dynamic response for adsorption, allowing purification within very shallow bed at high flow velocities and low differential pressure [1, 2].

3.6. Flow Mixing via Electrokinetic Circulation

Electrokinetic phenomena are typically second-order phenomena, e.g., in streaming current measurements, an applied mechanical force produces an electric current [14]. When treated phenomenologically, the second order phenomena can be treated by irreversible thermodynamics [15]. Even though classical thermodynamics describes electric double layer (EDL) at rest, in electrokinetics EDL is not at rest. However, usually the deviations from the equilibrium distribution of charge are disregarded [15].

Figure 4 shows removal efficacy of MS2 virus and Raoultella Terrigena (RT) bacteria by 3-mm deep precoat of 2Dγ-AlOOH/DE and diatomaceous earth (DE) particle mixture with equal average particle sizes of 80 μm as a function of average layer thickness formed by four neighboring 2Dγ-AlOOH/DE particles.

Figure 4 also reveals good correlation (coefficient of determination R²> 0.99) between logarithm reduction values (LRV) of microbial removal efficacy and average layer thickness formed by four neighboring 2D γ-AlOOH/DE particles (Table 2):

where a is a constant and x₀ is the average thickness of 2D γ-AlOOH/DE layer within a mix that would reduce the initial concentration, C_initial, by a factor of 10. The thickness of 2D γ-AlOOH/DE precoat layer that would reduce concentration of biological particles in the water stream by a factor of 10 is equal to x₀(MS2) =0.8 mm for MS2 virus and x₀(RT) = 0.5 mm for RT bacteria.

3.7. Ageing Characteristics of the 2D and 1D γ-AlOOH Crystallites

The main application of the prepared 2Dγ-AlOOH, 1Dγ-AlOOH, and 2Dβ-FeOOH/2Dγ-AlOOH crystallites deposited on diatomaceous earth (DE) particles is as water purification media. Additionally, since we are proposing a low cost and large-scale production of these crystallites, it was important to know their stability throughout the time. For this reason, the removal efficacy of aqueous particles by the prepared 1D, 2D γ-AlOOH, and 2Dβ-FeOOH/2Dγ-AlOOH crystallites was evaluated after fourteen and seven years, respectively (Table 3).

From the results presented in Table 3, it was found that the prepared 1D, 2D γ -AlOOH and 2Dβ-FeOOH/2Dγ-AlOOH crystallites remain monocrystalline under ambient conditions and no degradation in performance (i.e., TEM, particle size distribution, etc.) was noticed over periods of seven to fourteen years of manufacturing. This finding makes the crystallites to be industrially applicable.

4. Conclusions

In conclusion, aluminum-water reaction (equation (1)) has successfully been used to produce 2D and 1D quantum-sized and nanometer-sized γ-AlOOH mesostructures deposited onto siliceous substrates in a one-step process at moderate temperature [6–8]. Low cost, large scale manufacturing (several metric tons per year) of siliceous substrates coated with 2D and 1D arrays of γ-AlOOH crystallites and further functionalized with 2D atomically thin nanobelts of akaganeite β-FeOOH crystallites was demonstrated. A model explaining the pH dependent behavior of the zeta potential based on contributions from the three morphological planes of different chemical composition existing at siliceous particles coated with 2D and 1D γ-AlOOH crystallites was proposed: γ-AlOOH face and edge layers, and siliceous basal layer which are complex oxides of the two constituents: γ-AlOOH and SiO₂. The isoelectric point values of rough 2D γ-AlOOH, 1D γ-AlOOH, and 2D β-FeOOH/2D γ-AlOOH crystallites deposited on DE surfaces were increased by three pH units as compare to the flat crystalline γ-AlOOH and β-FeOOH surfaces resulting in a high removal efficacy of submicron particles from aqueous suspension by the surfaces with combined microscale and nanoscale structures. This suggests the existence of coupling electrokinetic effect of the local electric double layer (EDL) fields with the local flow fields which was further confirmed by a good correlation (coefficient of determination R²> 0.99) between LRV values of microbial removal efficacy and average layer thickness formed by four neighboring 2Dγ-AlOOH/DE particles (Table 2). Finally, the prepared 2D and 1D γ-AlOOH crystallites remain monocrystalline under ambient conditions and no degradation in characteristics (i.e., TEM, particle size distribution, etc.) and performance (i.e., virus, bacteria and metal ion removal efficacy) was noticed over periods of several years (i.e., seven to fourteen years).

Data Availability

The data used to support the findings of this study are included within the article.

Conflicts of Interest

No potential conflict of interest was reported by the authors.

References

L. Kaledin, F. Tepper, Y. Vesga, and T. Kaledin, “The effect of the surface roughness and ageing characteristics of boehmite on the removal of biological particles from aqueous solution,” AIMS Materials Science, vol. 6, no. 4, pp. 498–508, 2019.
View at: Publisher Site | Google Scholar
L. Kaledin, F. Tepper, and T. Kaledin, “Electrokinetic aspects of water filtration by AlOOH-coated siliceous particles with nanoscale roughness,” AIMS Materials Science, vol. 4, no. 2, pp. 470–486, 2017.
View at: Publisher Site | Google Scholar
S. Farrah and D. Preston, “Concentration of viruses from water by using cellulose filters modified by in situ precipitation of ferric and aluminum hydroxides,” Applied and Environmental Microbiology, vol. 50, no. 6, pp. 1502–1504, 1985.
View at: Google Scholar
J. Lukasik, S. Farrah, S. Truesdail, and D. Shah, “Adsorption of microorganisms to sand diatomaceous earth particles coated with metallic hydroxides,” Kona Powder and Particle Journal, vol. 14, pp. 87–91, 1997.
View at: Publisher Site | Google Scholar
S. E. Truesdail, J. Lukasik, S. R. Farrah, D. O. Shah, and R. B. Dickinson, “Analysis of bacterial deposition on metal (hydr)oxide-coated sand filter media,” Journal of Colloid and Interface Science, vol. 203, no. 2, pp. 369–378, 1998.
View at: Publisher Site | Google Scholar
F. Tepper and L. Kaledin, “Nanosize electropositive fibrous adsorbent,” in U.S Patent No. 6,838,005, U.S. Patent and Trademark Office, Washington, DC, 2005.
View at: Google Scholar
F. Tepper and L. Kaledin, “Drinking water filtration device,” in US Patent No. 7,390,343, U.S. Patent and Trademark Office, Washington, DC, 2008.
View at: Google Scholar
L. Kaledin, F. Tepper, and T. Kaledin, “Aluminized silicious powder and water purification device incorporating the same,” in US Patent No. 9,309,131, U.S. Patent and Trademark Office, Washington, DC, 2016.
View at: Google Scholar
B. Derjaguin and L. Landau, “Theory of the stability of strongly charged lyophobic sols and of the adhesion of strongly charged particles in solutions of electrolytes,” Progress in Surface Science, vol. 43, no. 1-4, pp. 30–59, 1993.
View at: Publisher Site | Google Scholar
E. Verwey and J. Overbeek, Theory of the Stability of Lyophobic Colloids, Elsevier, Amsterdam, 1948.
C. Schnitzer and S. Ripperger, “Influence of surface roughness on streaming potential method,” Chemical Engineering and Technology, vol. 31, no. 11, pp. 1696–1700, 2008.
View at: Publisher Site | Google Scholar
D. Parsons, R. Walsh, and V. Craig, “Surface forces: surface roughness in theory and experiment,” The Journal of Chemical Physics, vol. 140, no. 16, p. 164701, 2014.
View at: Publisher Site | Google Scholar
S. Seeger, B. Palm, J. Günster, and J. Heinrich, “On the influence of the particle size on the zeta potential of ultra-pure silica powders,” Ber DKG, vol. 92, no. 4, pp. E35–E40, 2015.
View at: Google Scholar
J. Lyklema, Fundamentals of Interface and Colloid Science: Solid-Liquid Interfaces, vol. 2, Academic Press, San Diego, 1995, Chaps.
J. Lyklema, Fundamentals of Interface and Colloid Science: Fundamentals, vol. 1, Academic Press, London, 1991.
J. Lyklema, “Electrokinetics after Smoluchowski,” Colloids and Surfaces A: Physicochemical Engineering Aspects, vol. 222, no. 1-3, pp. 5–14, 2003.
View at: Publisher Site | Google Scholar
R. Hunter, Foundations of Colloid Science, Chapt. 6, 8, Oxford University Press, Oxford, 2001.
R. C. Cohen and C. J. Radke, “Streaming potentials of nonuniformly charged surfaces,” Journal of Colloid and Interface Science, vol. 141, no. 2, pp. 338–347, 1991.
View at: Publisher Site | Google Scholar
D. Li, Electrokinetics in microfluidics, in Interface science and technology, Ed. A, vol. 2, no. 6, Habbard, Elsevier, Amsterdam, 2004, Chap.
D. Erickson and D. Li, “Microchannel flow with patchwise and periodic surface heterogeneity,” Langmuir, vol. 18, no. 23, pp. 8949–8959, 2002.
View at: Publisher Site | Google Scholar
D. Erickson and D. Li, “Streaming potential and streaming current methods for characterizing heterogeneous solid surfaces,” Journal of Colloid and Interface Science, vol. 237, no. 2, pp. 283–289, 2001.
View at: Publisher Site | Google Scholar
W. H. Gitzen, Alumina as a Ceramic Material, American Ceramic Society, Special Publication 4, Westerville, The American Ceramic Society, Ohio, 1970.
A. K. Geim and I. V. Grigorieva, “Van der Waals heterostructures,” Nature, vol. 499, no. 7459, pp. 419–425, 2013.
View at: Publisher Site | Google Scholar
X. Bokhimi, J. Toledo-Antonio, M. Guzman-Castillo, and F. Hernandez-Beltran, “Relationship between crystallite size and bond lengths in boehmite,” Journal of Solid State Chemistry, vol. 159, no. 1, pp. 32–40, 2001.
View at: Publisher Site | Google Scholar
R. P. Nair, P. Blake, A. N. Grigorenko et al., “Fine structure constant defines visual transparency of graphene,” Science, vol. 320, no. 5881, p. 1308, 2008.
View at: Publisher Site | Google Scholar
L. Kaledin, F. Tepper, and T. Kaledin, “Pristine point of zero charge (p.p.z.c.) and zeta potentials of boehmite’s nanolayer and nanofiber surfaces,” International Journal of Smart and Nano Materials, vol. 7, no. 1, pp. 1–21, 2016.
View at: Publisher Site | Google Scholar
M. Kosmulski, Surface Charging and Point of Zero Charge, CRC Press, Taylor & Francis group, Boca Raton, 2009.
View at: Publisher Site
F. Borghi, V. Vyas, A. Podesta, and P. Milani, “Nanoscale roughness and morphology affect the isoelectric point of titania surfaces,” PLoS One, vol. 8, no. 7, article e68655, 2013.
View at: Publisher Site | Google Scholar
D. Lombardo, P. Calandra, E. Bellocco et al., “Effect of anionic and cationic polyamidoamine (PAMAM) dendrimers on a model lipid membrane,” Biochimica et Biophysica Acta (BBA) – Biomembranes, vol. 1858, no. 11, pp. 2769–2777, 2016.
View at: Publisher Site | Google Scholar
W. Stumm, Chemistry of the Solid-Water Interface: Processes at the Mineral Water and Particle-Water Interface in Natural Systems, Wiley-Interscience, New York, 1992.
P. A. Thiessen, “Kennzeichnung submikroskopischer Grenzflächenbereiche verschiedenartiger Wirksamkeit,” Zeitschrift für Anorganische Chemie, vol. 253, no. 3-4, pp. 161–169, 1947.
View at: Publisher Site | Google Scholar
H. van Olphen, An Introduction to Clay Colloid Chemistry, John Wiley and Sons, New York, 2nd Ed. edition, 1977.
S. Assemi, J. Nalaskowski, J. Miller, and W. Johnson, “Isoelectric point of fluorite by direct force measurements using atomic force microscopy,” Langmuir, vol. 22, no. 4, pp. 1403–1405, 2006.
View at: Publisher Site | Google Scholar
R. Kershner, J. Bullard, and M. Cima, “Zeta potential orientation dependence of sapphire substrates,” Langmuir, vol. 20, no. 10, pp. 4101–4108, 2004.
View at: Publisher Site | Google Scholar
J. Bullard and M. Cima, “Orientation dependence of the isoelectric point of TiO₂ (rutile) surfaces,” The Journal of Physical Chemistry, vol. 99, pp. 2114–2118, 1995.
View at: Google Scholar
H. Hogenesch, “Mechanism of Immunopotentiation and safety of aluminum adjuvants,” Frontiers in Immunology, vol. 3, article 406, 2013.
View at: Publisher Site | Google Scholar
Argonide Corporation, Preparation of 3-mm deep precoat from 80 μm DE powders, 2015, http://www.tinyurl.com/my6jmzz.
A. Einstein, Investigations on the Theory of the Brownian Movement, Dover Publications, New York, NY, 1956.

Copyright

Copyright © 2019 Leonid A. Kaledin et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

1000

Downloads

858

Citations