One-Step Hydrothermal Synthesis of N, Fe-Codoped Carbon Dots as Mimic Peroxidase and Application on Hydrogen Peroxide and Glucose Detection

Li, Yan; Weng, Yuhui; Lu, Shikong; Xue, Meihua; Yao, Bixia; Weng, Wen; Zheng, Tao

doi:https://doi.org/10.1155/2020/1363212

Journal of Nanomaterials

On this page

Abstract Introduction Results and Discussion Conclusions Data Availability Conflicts of Interest Acknowledgments References Copyright Related Articles

Research Article | Open Access

Volume 2020 | Article ID 1363212 | https://doi.org/10.1155/2020/1363212

One-Step Hydrothermal Synthesis of N, Fe-Codoped Carbon Dots as Mimic Peroxidase and Application on Hydrogen Peroxide and Glucose Detection

Yan Li,¹Yuhui Weng,¹Shikong Lu,¹Meihua Xue,¹Bixia Yao,¹Wen Weng,^1,2,3and Tao Zheng⁴

Academic Editor: Zehra Durmus

Received07 Feb 2020

Revised08 Apr 2020

Accepted20 Apr 2020

Published08 May 2020

Abstract

In this paper, N, Fe-codoped carbon dots (N, Fe-CDs) were synthesized from β-cyclodextrin, ethylenediamine, and ferric chloride for the first time using a convenient one-step hydrothermal method. The obtained N, Fe-CDs were characterized by various methods including transmission electron microscopy, X-ray photoelectron spectroscopy, and Fourier-transform infrared spectroscopy. The N, Fe-CDs exhibited better catalytic activity than horseradish peroxidase (HRP) and caused an evident color change for 3,3,5,5-tetramethylbenzidine in the presence of H₂O₂. Kinetic experiments show that the apparent K_m value for the N, Fe-CDs with TMB (0.40 mM) or H₂O₂ (0.35 mM) as the substrate was lower than that of HRP (0.43 and 3.70 mM), suggesting that the N, Fe-CDs have a much higher affinity for TMB and H₂O₂ than HRP. The K_m/V_max value for the N, Fe-CDs ( for H₂O₂) is significantly lower than that for HRP (), suggesting that the N, Fe-CDs have a stronger catalytic efficiency for H₂O₂ than HRP. Furthermore, a highly efficient and sensitive colorimetric detection method for glucose was developed using the N, Fe-CDs as mimic peroxidase to detect the hydrogen peroxide generated by the oxidation of glucose by glucose oxidase. The limit of detection for H₂O₂ and glucose was found to be 0.52 and 3.0 μM, respectively. The obtained N, Fe-codoped carbon dots, which possess simulated peroxidase activity, can potentially be used in the field of biotechnology.

1. Introduction

Peroxidase such as horseradish peroxidase (HRP) is a kind of natural enzyme that catalyzes the decomposition of peroxides and prevents biological cells from being damaged by toxic substances [1]. However, the natural enzyme would suffer from degradation, denaturation, and inactivation in practical applications especially under harsh conditions. The extraction, purification, and storage processes of natural peroxidase are also fussy. High price further limits its applications [2–4]. Under this background, various enzyme mimics have been developed in order to address these issues.

Recently, multiple inorganic nanomaterials, such as FeOOH nanorods [5], Co₄N nanowires [6], WSe₂ nanosheets [7], yolk-shell nanostructured Fe₃O₄@C magnetic nanoparticles [8], MnO₂ nanowires [9], amine-grafted metal-organic frameworks (MOFs) [10], and apoferritin-paired gold clusters [11], have been found to exhibit the properties of oxidase or peroxidase-like enzymes [12]. In addition, carbon-based nanomaterials, such as graphene oxide [13], carbon nanotubes [14], carbon nanodots [15], carbonitride sheets [16], graphene quantum dots [17], and C₃N₄ nanosheet-supported Prussian Blue nanoparticles [18], have been found to possess peroxidase-like or superoxide dismutase-like activity [19]. This nanomaterial has been widely used in biosensor, bioimaging, catalysis, light-emitting diode device, and medical diagnosis due to their low cytotoxicity, good biocompatibility, easy functionalization, and high stability [20–27].

In this paper, a new mimic peroxidase, N, Fe-codoped carbon dots (N, Fe-CDs) were synthesized from β-cyclodextrin, ethylenediamine, and ferric chloride using a convenient one-step hydrothermal method. The obtained N, Fe-CDs exhibited better catalytic activity than HRP. Combining with glucose oxidase (GOx), a good colorimetric method for glucose detection was developed.

2. Experimental Section

2.1. Materials

β-Cyclodextrin was purchased from Shanghai Sinopharm Chemical Reagent Co. Ltd. (Shanghai, China; www.reagent.com.cn). Ethylenediamine, glucose, fructose, maltose, xylose, ascorbic acid, uric acid, α-lactose, sucrose, terephthalic acid (TA), ferric chloride hexahydrate, and hydrogen peroxide (30%) were purchased from XiLong Chemical Co. Ltd. (Guangdong, China; www.xlhg.com). 3,3,5,5-tetramethylbenzidine (TMB), glucose oxidase (180U/mg), and rhodamine B (RhB) were purchased from Aladdin Reagent Co. Ltd. (Shanghai, China; http://www.aladdine.com). Ultrapure water (18.2Ωcm) was prepared by a Milli-Q system (Millipore, Bedford, MA, USA; http://www.merckmillipore.com) and used in all experiments.

2.2. Analytical Methods

The morphology and size distribution of the nanoparticles were studied using a Tecnai-G2 F20 transmission electron microscope (TEM) with an accelerating voltage of 200 kV (FEI; http://www.fei.com). X-ray photoelectron spectroscopy (XPS) was performed using a Thermo Escalab 250 Xi photoelectron spectrometer (Thermo Fisher; http://www.thermoscientific.com). Fourier transform infrared (FTIR) spectra were recorded using a Magna-IR 750 Fourier transform infrared spectrometer (Nicolet; http://www.thermofisher.com), and absorption spectra were obtained using a SPECORD 200 PLUS UV-vis spectrometer (Analytik Jena; http://www.analytik-jena.com.cn).

2.3. Synthesis of the N, Fe-CDs

The N, Fe-CDs were prepared using a one-step hydrothermal synthesis method [21, 27]. Briefly, 0.5 g of β-cyclodextrin, 2 mL of ethylenediamine, and 0.5 g of FeCl₃∙6H₂O were firstly dissolved in 50 mL of ultrapure water. Then, the solution was transferred to a Teflon-lined, stainless-steel autoclave and heated at 180°C for 0.5 h. The mixture was then cooled to room temperature and filtered through a 0.22 μm filter under the negative pressure by the water pump. The supernatant was dialyzed against ultrapure water for 24 hours, and then freeze-dried for later use. As control, N-CDs were synthesized in the same way but without FeCl₃∙6H₂O.

2.4. Mimic Peroxidase Activity of the N, Fe-CDs

The mimic peroxidase activity of N, Fe-CDs was determined using the following procedures. First, 100 μL of N, Fe-CDs (150 μg/mL) was added to an acetic acid solution (0.1 M, pH 2.5) containing 100 μM H₂O₂ and 700 μM TMB. Color changes were observed after the solution had been incubated in a 35°C water bath for 36 min. In order to investigate the catalytic mechanism, the experiment was repeated using different concentrations of TMB and H₂O₂. Then, the key kinetic parameters were calculated from the double reciprocal Lineweaver–Burk equation: where is the initial velocity, is the maximal reaction velocity, and is the Michaelis–Menten constant, and is the concentration of the substrate. The initial velocity was obtained by calculating the slopes of absorbance changes at 652 nm within 100 s.

2.5. RhB Oxidation Experiment

The degradation of RhB is generally used to demonstrate whether hydroxyl radicals (∙OH) are generated during the oxidation of H₂O₂. In this work, an aqueous solution of 100 μL of H₂O₂ (100 μM) was added to a solution of 200 μL of RhB (50 μM) and 100 μL N, Fe-CDs (150 μg/mL), diluted with acetate buffer solution to 1 mL. The reaction was performed for 12 h in the dark at room temperature. The change in the absorbance of the solution in the range of 200 to 800 nm was monitored to elucidate the catalytic mechanism.

2.6. Detection of Hydroxyl Radicals Experiment

TA was used as a fluorescence probe for tracking ∙OH. A standard solution of the TA sodium salt (Na₂TA) with a concentration of 25 mM was prepared by dissolving 830.7 mg of TA in 200 mL of NaOH (62.5 mM), and 0.4 mL of this Na₂TA solution was added to a mixture of 3.6 mL acetate buffer solution (100 mM, pH 2.5), 25 mg/L N, Fe-CDs, and 0.1 M H₂O₂. After incubation at 25°C for 12 h in the dark, the solution was centrifuged and used in the fluorescence measurement. The excitation wavelength used in fluorescence measurement is 315 nm, and the emission wavelength range is from 350 to 600 nm.

2.7. Colorimetric Detection of H₂O₂ and Glucose

Colorimetric detection of H₂O₂ was performed as follows. A solution containing 200 μL of TMB (700 μM), 100 μL of N, Fe-CDs (150 μg/mL), 100 μL of H₂O₂ at different concentrations, and 600 μL of acetate buffer (0.1 M, pH 2.5) was incubated in a 35°C water bath for 36 min. After that, the absorption spectra of the reacted solution were recorded in the range of 500 nm to 800 nm.

Glucose detection was carried out as follows: first, 20 μL of GOx (1 mg/mL), 20 μL of glucose at different concentrations, and 60 μL of phosphate-buffered saline (PBS, 0.1 M, pH 7.0) were mixed and incubated at a 37°C water bath for 60 min. Then, 200 μL of TMB (700 μM), 100 μL of N, Fe-CDs (150 μg/mL), and 600 μL of acetate buffer (0.1 M, pH 2.5) were successively added to the glucose reaction solution and incubated in a water bath at 35°C for 36 min. Finally, the UV-vis spectrum of the mixed solution was recorded using a UV-vis spectrometer. Control experiments, in which 0.5 mM glucose was replaced by 5 mM fructose, ascorbic acid, maltose, xylose, uric acid, α-lactose, and sucrose, were also performed. Each point was measured three times. The standard errors, defined as the average squared deviation of each number from its mean, were calculated using origin software.

3. Results and Discussion

3.1. Characterizations of the N, Fe-CDs

The TEM image in Figure 1(a) shows that the N, Fe-CDs had good dispersibility, and the size was in the range of 0.9–2.5 nm. FTIR was used to analyze the functional groups in the material. The FTIR spectrum (Figure 1(b)) shows a broad peak at 3328 cm^-1, which was ascribed to the stretching vibrations of the O-H and N-H bonds. The intense band at 2920 cm^-1 arose from symmetric C-H stretching vibrations, and the characteristic band at 1030 cm^-1 was assigned to the vibration of the C-N bond.

(a)

(b)

XPS was performed to analyze the composition of the N, Fe-CDs, and the results are shown in Figure 2(a). Four elements (C, N, O, and Fe) were detected in the XPS spectrum of the N, Fe-CDs. The oxygen content was found to be as high as 31.78%, which further suggests that the N, Fe-CDs contained abundant functional groups. The main peak at 286.25 eV, attributed to C 1 s, was deconvoluted into four contributing peaks at 284.5, 285.0, 286.2, and 287.7 eV (Figure 2(b)), which indicates the presence of four carbon environments: sp² C=C or sp³ C-C, C-N, sp² N-C=N, and C=O [28], respectively. The peak at 399.51 eV, attributed to N 1 s, was deconvoluted into three contributing peaks at 399.2, 399.8, and 401.5 eV (Figure 2(c)), which indicates the presence of three types of nitrogen environments: C-N, C=N, and C=N-H, respectively [29]. The peak at 532.61 eV was ascribed to O 1 s, which can be resolved into 532.0, 532.6, and 533.2 eV, corresponding to the C-O, C=O, and O-H bonds, respectively [30]. The weak peak at 716.57 eV was ascribed to Fe 2p. The content of Fe was 0.56%, indicating that Fe has been successfully incorporated into the nanoparticles.

(a)

(b)

(c)

(d)

3.2. Evaluation of the Peroxidase-Like Catalytic Activity of the N, Fe-CDs

To investigate the peroxidase-like activity of N, Fe-CDs, colorimetry was carried out using TMB as a substrate in the absence and presence of H₂O₂ and N, Fe-CDs. As shown in Figure 3, a significant absorption peak appeared at 658 nm due to oxidation of TMB in the presence of H₂O₂ and the N, Fe-CDs (Figure 3(d)). This peak was significantly smaller in the absence of the N, Fe-CDs, which shows that the N, Fe-CDs did show great catalytic performance. No significant absorption peaks were observed in the control experiments, including the absence of the N, Fe-CDs (Figures 3(a) and 3(c)) or H₂O₂ (Figure 3(f)) and the replacement of N, Fe-CDs with N-CDs (Figures 3(b) and 3(e)).

The influence of the N, Fe-CDs and TMB concentrations, the pH value, the reaction temperature, and duration on the catalytic performance were further evaluated, and the results are shown in Figure 4. The absorbance is shown as a function of the N, Fe-CDs concentration in Figure 4(a), interestingly, low concentrations of N, Fe-CDs showed high activity towards TMB oxidation, but the absorbance changed little when the N, Fe-CDs concentration exceeded 150 μg/mL. Therefore, a N, Fe-CDs concentration of 150 μg/mL was used in the subsequent experiment. The absorbance increased continuously as the TMB concentration and reaction duration increased. The optimal TMB concentration and reaction duration were determined to be 700 μM (Figure 4(b)) and 36 min (Figure 4(e)), respectively. Figure 4(c) shows the change in absorbance caused by varying the pH from 2.0 to 7.0. The results indicate that catalytic activity of the N, Fe-CDs was highest at a pH of 2.5. The catalytic activity of the N, Fe-CDs was also increased when the temperature increased from 25 to 35°C, but it decreased temperatures higher than 35°C (Figure 4(d)).

(a)

(b)

(c)

(d)

(e)

In order to better understand the mechanism by which N, Fe-CDs catalyze TMB and H₂O₂ oxidation, the apparent steady-state kinetics were measured. As shown in Figures 5(a) and 5(b), a range of TMB and H₂O₂ concentrations were used in the catalytic reactions so that the kinetic parameters could be obtained using Lineweaver–Burk plots (Figures 5(C) and 5(D)). Table 1 compares the parameters for this system with those of HRP. A smaller value indicates a stronger affinity between the enzyme and the substrate and a higher catalyst efficiency. The value for N, Fe-CDs with TMB or H₂O₂ as substrate was lower than that of HRP, which suggests that the N, Fe-CDs have a higher affinity for TMB and H₂O₂ than HRP does. On the other hand, although the values of the N, Fe-CDs were smaller than those of HRP, the value of the N, Fe-CDs with H₂O₂ as substrate was smaller than those of HRP. The lower the value of is, the higher the catalytic efficiency is. Considering their peroxidase mimetic activity, the N, Fe-CDs could be employed as a potential substitute for HRP.

(a)

(b)

(c)

(d)

The fitted Lineweaver–Burk lines were nearly parallel at different concentrations of TMB and H₂O₂. That means the N, Fe-CDs bind to and react with the first substrate, release the product, then recombine with the second substrate, react and release the second product in a manner similar to the ping-pong mechanism of HRP [31, 32].

3.3. Mechanism of the Peroxidase-like Activity of N, Fe-CDs

Generally, the catalytic pathway for peroxidase-like activity can be divided into two types, reactive oxygen species generation and an electron transfer process [33–35]. To evaluate the possible active intermediates in the present system, various fluorescent and colorimetric probes were employed. RhB was used to detect ∙OH as the presence of ∙OH would cause a decrease in the absorbance intensity of RhB. Figure 6(a) shows the change in absorbance of a solution containing RhB, H₂O_2, and N, Fe-CDs. After reacting for 12 h, a negligible decrease in the absorbance was observed compared with the control experiments, which indicates the absence of ∙OH in the peroxidase-like catalytic process. TA was used as a fluorescence probe for tracking ∙OH, because it can capture ∙OH and generate 2-hydroxyterephthalic acid, thereby emitting a unique fluorescence signal at around 425 nm. After reacting for 12 h, the fluorescence of a solution containing Na₂TA, H₂O₂, and different concentrations of N, Fe-CDs was lower than that of the mixture of Na₂TA and H₂O₂ (Figure 6(b)). These results show that ∙OH is not generated as a reaction intermediate during the peroxidase-like catalysis. The reaction route may be described by following reaction equations.

(a)

(b)

3.4. Detection of H₂O₂ and Glucose

On the basis of the peroxidase mimetic activity of the N, Fe-CDs, an efficient and fast colorimetric method for the detection of H₂O₂ was created. A typical H₂O₂ concentration–absorbance profile is shown in Figure 7(a). The magnitude of the peak at 658 nm increased with the increased concentration of H₂O₂. A linear relationship between the absorbance and the H₂O₂ concentration from 0 to 60 μM was obtained (), and the limit of detection (LOD) was calculated to be 0.52 μM based on three times the standard deviation rule (). Also, the color of the mixture changed (inset of Figure 7(a)), which indicates that H₂O₂ can be detected with the naked eye.

(a)

(b)

As glucose would be oxidized to H₂O₂ and gluconic acid in the presence of glucose oxidase, this method can be used to detect glucose indirectly when combined with the catalytic properties of GOx and N, Fe-CDs. Figure 8(a) shows that the absorbance at the peak of 658 nm increased as the concentration of glucose increased. There exist two parts of linear range between the absorbance and the concentration of glucose in the range of 0 to 60 μM and 60 to 100 μM (Figures 8(b)-8(d)). The LOD was calculated to be 3.0 μM. As shown in Table 2, this method was comparable or more sensitive than other reported systems based on different nanoparticles as peroxidase mimics.

(a)

(b)

(c)

(d)

To further investigate the specificity of this method, five other sugars (fructose, maltose, xylose, α-lactose, and sucrose), ascorbic acid, and uric acid were selected as interfering substances for detection. Figure 9 shows the absorbance at 658 nm of solutions containing the other sugars, ascorbic acid, and uric acid at concentrations that were ten times higher than that of glucose (0.5 mM). The absorbance of the other substances differs little from that of the blank (glucose-free) sample, which shows that this method has good glucose selectivity.

(a)

(b)

4. Conclusions

As a conclusion, N, Fe-CDs were synthesized from β-cyclodextrin, ethylenediamine, and FeCl₃∙6H₂O using a one-step hydrothermal method for the first time. The raw materials are easily available, and the preparation process is convenient. The obtained N, Fe-CDs exhibited good activity of mimic peroxidase. In the presence of H₂O₂, the catalytic oxidation of TMB by N, Fe-CDs can produce green water-soluble products. This catalytic oxidation process conforms to the Michaelis–Menten model, and the N, Fe-CDs demonstrated better activity than HRP. On this basis, a highly sensitive and selective colorimetric method was developed for the detection of H₂O₂ and glucose. The LODs of H₂O₂ and glucose were 0.52 and 3.0 μM, respectively. This study presents an artificial enzyme that may replace natural peroxidases in biomedical and environmental testing.

Data Availability

Some or all data, models, or code generated or used during the study are available in a repository or online in accordance with funder data retention policies.

Conflicts of Interest

The authors have declared no conflict of interest.

Acknowledgments

This work was supported by Major Science and Technology Projects of Zhangzhou City (No. zz2018ZD20), and the Natural Science Foundation of Fujian Province of China (Nos. 2016Y0065 and 2019S0031).

References

X. Chen, X. Tian, B. Su, Z. Huang, X. Chen, and M. Oyama, “Au nanoparticles on citrate-functionalized graphene nanosheets with a high peroxidase-like performance,” Dalton Transactions, vol. 43, no. 20, pp. 7449–7454, 2014.
View at: Publisher Site | Google Scholar
J. Cui, S. Ren, B. Sun, and S. Jia, “Optimization protocols and improved strategies for metal-organic frameworks for immobilizing enzymes: current development and future challenges,” Coordination Chemistry Reviews, vol. 370, pp. 22–41, 2018.
View at: Publisher Site | Google Scholar
O. Barbosa, C. Ortiz, Á. Berenguer-Murcia, R. Torres, R. C. Rodrigues, and R. Fernandez-Lafuente, “Strategies for the one-step immobilization–purification of enzymes as industrial biocatalysts,” Biotechnology Advances, vol. 33, no. 5, pp. 435–456, 2015.
View at: Publisher Site | Google Scholar
E. Shoji and M. S. Freund, “Potentiometric sensors based on the inductive effect on the pK_a of poly(aniline): a nonenzymatic glucose sensor,” Journal of the American Chemical Society, vol. 123, no. 14, pp. 3383-3384, 2001.
View at: Publisher Site | Google Scholar
X.-L. Zhong, S.-H. Wen, Y. Wang et al., “Colorimetric and electrochemical arsenate assays by exploiting the peroxidase-like activity of FeOOH nanorods,” Microchimica Acta, vol. 186, no. 11, 2019.
View at: Publisher Site | Google Scholar
Y. Z. Li, T. T. Li, W. Chen, and Y. Y. Song, “Co₄N nanowires: noble-metal-free peroxidase mimetic with excellent salt- and temperature-resistant abilities,” ACS Applied Materials & Interfaces, vol. 9, no. 35, pp. 29881–29888, 2017.
View at: Publisher Site | Google Scholar
T. M. Chen, X. J. Wu, J. X. Wang, and G. W. Yang, “WSe₂ few layers with enzyme mimic activity for high-sensitive and high-selective visual detection of glucose,” Nanoscale, vol. 9, no. 32, pp. 11806–11813, 2017.
View at: Publisher Site | Google Scholar
N. Lu, M. Zhang, L. Ding et al., “Yolk-shell nanostructured Fe₃O₄@C magnetic nanoparticles with enhanced peroxidase-like activity for label-free colorimetric detection of H₂O₂and glucose,” Nanoscale, vol. 9, no. 13, pp. 4508–4515, 2017.
View at: Publisher Site | Google Scholar
L. Han, P. Liu, H. Zhang, F. Li, and A. Liu, “Phage capsid protein-directed MnO₂ nanosheets with peroxidase-like activity for spectrometric biosensing and evaluation of antioxidant behaviour,” Chemical Communications, vol. 53, no. 37, pp. 5216–5219, 2017.
View at: Publisher Site | Google Scholar
A. H. Valekar, B. S. Batule, M. I. Kim et al., “Novel amine-functionalized iron trimesates with enhanced peroxidase-like activity and their applications for the fluorescent assay of choline and acetylcholine,” Biosensors and Bioelectronics, vol. 100, pp. 161–168, 2018.
View at: Publisher Site | Google Scholar
X. Jiang, C. Sun, Y. Guo, G. Nie, and L. Xu, “Peroxidase-like activity of apoferritin paired gold clusters for glucose detection,” Biosensors and Bioelectronics, vol. 64, pp. 165–170, 2015.
View at: Publisher Site | Google Scholar
J. Wu, X. Wang, Q. Wang et al., “Nanomaterials with enzyme-like characteristics (nanozymes): next-generation artificial enzymes (II),” Chemical Society Reviews, vol. 48, no. 4, pp. 1004–1076, 2019.
View at: Publisher Site | Google Scholar
H.-H. Xu, H.-H. Deng, X.-Q. Lin et al., “Colorimetric glutathione assay based on the peroxidase-like activity of a nanocomposite consisting of platinum nanoparticles and graphene oxide,” Microchimica Acta, vol. 184, no. 10, pp. 3945–3951, 2017.
View at: Publisher Site | Google Scholar
Y. Song, X. Wang, C. Zhao, K. Qu, J. Ren, and X. Qu, “Label-free colorimetric detection of single nucleotide polymorphism by using single-walled carbon nanotube intrinsic peroxidase-like activity,” Chemistry - A European Journal, vol. 16, no. 12, pp. 3617–3621, 2010.
View at: Publisher Site | Google Scholar
W. Shi, Q. Wang, Y. Long et al., “Carbon nanodots as peroxidase mimetics and their applications to glucose detection,” Chemical Communications, vol. 47, no. 23, pp. 6695–6697, 2011.
View at: Publisher Site | Google Scholar
T. Lin, L. Zhong, J. Wang et al., “Graphite-like carbon nitrides as peroxidase mimetics and their applications to glucose detection,” Biosensors and Bioelectronics, vol. 59, pp. 89–93, 2014.
View at: Publisher Site | Google Scholar
X. Wu, Y. Zhang, T. Han, H. Wu, S. Guo, and J. Zhang, “Composite of graphene quantum dots and Fe₃O⁴ nanoparticles: peroxidase activity and application in phenolic compound removal,” RSC Advances, vol. 4, no. 7, pp. 3299–3305, 2014.
View at: Publisher Site | Google Scholar
D. Zhou, C. Wang, J. Luo, and M. Yang, “C₃N₄ nanosheet-supported Prussian Blue nanoparticles as a peroxidase mimic: colorimetric enzymatic determination of lactate,” Microchimica Acta, vol. 186, no. 11, 2019.
View at: Publisher Site | Google Scholar
W. Wang, X. Jiang, and K. Chen, “Iron phosphate microflowers as peroxidase mimic and superoxide dismutase mimic for biocatalysis and biosensing,” Chemical Communications, vol. 48, no. 58, pp. 7289–7291, 2012.
View at: Publisher Site | Google Scholar
M. Shamsipur, K. Molaei, F. Molaabasi et al., “Facile preparation and characterization of new green emitting carbon dots for sensitive and selective off/on detection of Fe³⁺ ion and ascorbic acid in water and urine samples and intracellular imaging in living cells,” Talanta, vol. 183, pp. 122–130, 2018.
View at: Publisher Site | Google Scholar
N. Amin, A. Afkhami, L. Hosseinzadeh, and T. Madrakian, “Green and cost-effective synthesis of carbon dots from date kernel and their application as a novel switchable fluorescence probe for sensitive assay of Zoledronic acid drug in human serum and cellular imaging,” Analytica Chimica Acta, vol. 1030, pp. 183–193, 2018.
View at: Publisher Site | Google Scholar
H. Jia, D. Yang, X. Han, J. Cai, H. Liu, and W. He, “Peroxidase-like activity of the Co₃O₄ nanoparticles used for biodetection and evaluation of antioxidant behavior,” Nanoscale, vol. 8, no. 11, pp. 5938–5945, 2016.
View at: Publisher Site | Google Scholar
Y. Lin, J. Ren, and X. Qu, “Catalytically active nanomaterials: a promising candidate for artificial enzymes,” Accounts of Chemical Research, vol. 47, no. 4, pp. 1097–1105, 2014.
View at: Publisher Site | Google Scholar
V. Arul, T. N. J. I. Edison, Y. R. Lee, and M. G. Sethuraman, “Biological and catalytic applications of green synthesized fluorescent N-doped carbon dots using Hylocereus undatus,” Journal of Photochemistry and Photobiology B: Biology, vol. 168, pp. 142–148, 2017.
View at: Publisher Site | Google Scholar
D. Jampaiah, T. Srinivasa Reddy, A. E. Kandjani et al., “Fe-doped CeO₂ nanorods for enhanced peroxidase-like activity and their application towards glucose detection,” Journal of Materials Chemistry B, vol. 4, no. 22, pp. 3874–3885, 2016.
View at: Publisher Site | Google Scholar
N. Vasileva, T. Godjevargova, D. Ivanova, and K. Gabrovska, “Application of immobilized horseradish peroxidase onto modified acrylonitrile copolymer membrane in removing of phenol from water,” International Journal of Biological Macromolecules, vol. 44, no. 2, pp. 190–194, 2009.
View at: Publisher Site | Google Scholar
B. Wang, F. Liu, Y. Wu, Y. Chen, B. Weng, and C. M. Li, “Synthesis of catalytically active multielement-doped carbon dots and application for colorimetric detection of glucose,” Sensors and Actuators B: Chemical, vol. 255, pp. 2601–2607, 2018.
View at: Publisher Site | Google Scholar
J. Xian, Y. Weng, H. Guo, Y. Li, B. Yao, and W. Weng, “One-pot fabrication of Fe-doped carbon nitride nanoparticles as peroxidase mimetics for H₂O₂ and glucose detection,” Spectrochimica Acta Part A: Molecular and Biomolecular Spectroscopy, vol. 215, pp. 218–224, 2019.
View at: Publisher Site | Google Scholar
W. Yang, T. T. Huang, M. Zhao et al., “High peroxidase-like activity of iron and nitrogen co-doped carbon dots and its application in immunosorbent assay,” Talanta, vol. 164, pp. 1–6, 2017.
View at: Publisher Site | Google Scholar
Y. C. Lu, J. Chen, A. J. Wang et al., “Facile synthesis of oxygen and sulfur co-doped graphitic carbon nitride fluorescent quantum dots and their application for mercury (_II) detection and bioimaging,” Journal of Materials Chemistry C, vol. 3, no. 1, pp. 73–78, 2015.
View at: Publisher Site | Google Scholar
L. Huang, Z. Li, and L. Guo, “Colorimetric assay of acetylcholinesterase inhibitor tacrine based on MoO₂ nanoparticles as peroxidase mimetics,” Spectrochimica Acta Part A: Molecular and Biomolecular Spectroscopy, vol. 224, p. 117412, 2020.
View at: Publisher Site | Google Scholar
W. Dong and Y. Huang, “CeO₂/C nanowire derived from a cerium (III) based organic framework as a peroxidase mimic for colorimetric sensing of hydrogen peroxide and for enzymatic sensing of glucose,” Microchimica Acta, vol. 187, no. 1, 2020.
View at: Publisher Site | Google Scholar
M. Dervisevic, E. Dervisevic, and M. Şenel, “Recent progress in nanomaterial-based electrochemical and optical sensors for hypoxanthine and xanthine. A review,” Microchimica Acta, vol. 186, no. 12, 2019.
View at: Publisher Site | Google Scholar
E. Eskandari, M. Kosari, M. H. Davood Abadi Farahani et al., “A review on polyaniline-based materials applications in heavy metals removal and catalytic processes,” Separation and Purification Technology, vol. 231, p. 115901, 2020.
View at: Publisher Site | Google Scholar
H. Yang, Z. Wang, Q. Zhou, C. Xu, and J. Hou, “Nanoporous platinum-copper flowers for non-enzymatic sensitive detection of hydrogen peroxide and glucose at near-neutral pH values,” Microchimica Acta, vol. 186, no. 9, 2019.
View at: Publisher Site | Google Scholar
Q. Liu, Y. Yang, X. Lv et al., “One-step synthesis of uniform nanoparticles of porphyrin functionalized ceria with promising peroxidase mimetics for H₂O₂ and glucose colorimetric detection,” Sensors and Actuators B: Chemical, vol. 240, pp. 726–734, 2017.
View at: Publisher Site | Google Scholar
L. Han, J. Shi, and A. Liu, “Novel biotemplated MnO₂ 1D nanozyme with controllable peroxidase-like activity and unique catalytic mechanism and its application for glucose sensing,” Sensors and Actuators B: Chemical, vol. 252, pp. 919–926, 2017.
View at: Publisher Site | Google Scholar
L. Rastogi, D. Karunasagar, R. B. Sashidhar, and A. Giri, “Peroxidase-like activity of gum kondagogu reduced/stabilized palladium nanoparticles and its analytical application for colorimetric detection of glucose in biological samples,” Sensors and Actuators B: Chemical, vol. 240, pp. 1182–1188, 2017.
View at: Publisher Site | Google Scholar
T. Zhan, J. Kang, X. Li, L. Pan, G. Li, and W. Hou, “NiFe layered double hydroxide nanosheets as an efficiently mimic enzyme for colorimetric determination of glucose and H₂O₂,” Sensors and Actuators B: Chemical, vol. 255, pp. 2635–2642, 2018.
View at: Publisher Site | Google Scholar
F. Honarasa, F. H. Kamshoori, S. Fathi, and Z. Motamedifar, “Carbon dots on V₂O₅ nanowires are a viable peroxidase mimic for colorimetric determination of hydrogen peroxide and glucose,” Microchimica Acta, vol. 186, no. 4, 2019.
View at: Publisher Site | Google Scholar
F. Wang, W. Gong, L. Wang, and Z. Chen, “Enhanced amperometric response of a glucose oxidase and horseradish peroxidase based bienzyme glucose biosensor modified with a film of polymerized toluidine blue containing reduced graphene oxide,” Microchimica Acta, vol. 182, no. 11-12, pp. 1949–1956, 2015.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2020 Yan Li et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

1731

Downloads

1360

Citations

Journal of Nanomaterials

One-Step Hydrothermal Synthesis of N, Fe-Codoped Carbon Dots as Mimic Peroxidase and Application on Hydrogen Peroxide and Glucose Detection

Abstract

1. Introduction

2. Experimental Section

2.1. Materials

2.2. Analytical Methods

2.3. Synthesis of the N, Fe-CDs

2.4. Mimic Peroxidase Activity of the N, Fe-CDs

2.5. RhB Oxidation Experiment

2.6. Detection of Hydroxyl Radicals Experiment

2.7. Colorimetric Detection of H2O2 and Glucose

3. Results and Discussion

3.1. Characterizations of the N, Fe-CDs

3.2. Evaluation of the Peroxidase-Like Catalytic Activity of the N, Fe-CDs

3.3. Mechanism of the Peroxidase-like Activity of N, Fe-CDs

3.4. Detection of H2O2 and Glucose

4. Conclusions

Data Availability

Conflicts of Interest

Acknowledgments

References

Copyright

2.7. Colorimetric Detection of H₂O₂ and Glucose

3.4. Detection of H₂O₂ and Glucose