Unveiling the Direct Correlation between the CVD-Grown Graphene and the Growth Template

Lee, Junghyun; Seo, Jihyung; Jung, Sungchul; Park, Kibog; Park, Hyesung

doi:https://doi.org/10.1155/2018/7610409

Journal of Nanomaterials

On this page

Abstract Introduction Experimental Results and Discussion Conclusions Data Availability Conflicts of Interest Acknowledgments Supplementary Materials References Copyright Related Articles

Research Article | Open Access

Volume 2018 | Article ID 7610409 | https://doi.org/10.1155/2018/7610409

Unveiling the Direct Correlation between the CVD-Grown Graphene and the Growth Template

Junghyun Lee,¹Jihyung Seo,¹Sungchul Jung,²Kibog Park,²and Hyesung Park¹

Academic Editor: Mohamed Bououdina

Received29 Apr 2018

Accepted24 Jun 2018

Published19 Aug 2018

Abstract

Chemical vapor deposition (CVD) is known to produce continuous, large-area graphene sheet with decent physical properties. In the CVD process, catalytic metal substrates are typically used as the growth template, and copper has been adopted as the representative material platform due to its low carbon solubility and resulting monolayer graphene growth capability. For the widespread industrial applications of graphene, achieving the high-quality is essential. Several factors affect the qualities of CVD-grown graphene, such as pressure, temperature, carbon precursors, or growth template. In this work, we provide detailed analysis on the direct relation between the metallic growth substrate (copper) and overall properties of the resulting CVD-grown graphene. The surface morphology of copper substrate was modulated via simple chemical treatments, and its effect on physical, optical, and electrical properties of graphene was analyzed. Based on these results, we propose a simple synthesis route to produce high-quality, continuous, monolayer graphene sheet, which can facilitate the commercialization of CVD graphene into reality.

1. Introduction

Graphene is one-atomic-layer-thick carbon atoms with honeycomb lattice structures, which is the first kind of 2-dimensional materials that have been experimentally discovered since 2004 [1]. With its outstanding physical and chemical properties, graphene has been proposed as an emerging nanomaterial for the next-generation electronic devices, such as flexible electronics, high-frequency transistors, or photonic devices, exceeding the performance of conventional devices [2–9]. Ever since its experimental demonstrations, various synthesis routes have been introduced for the production of graphene [10–16]. To list a few, mechanical exfoliation can yield high-quality of pristine graphene, but it lacks the large-scale production capability, an essential feature required for industrial applications [1]. Liquid-phase exfoliation technique, commonly used in the synthesis of graphene oxide (GO) or graphene intercalation compound (GIC), is promising for large-scale production. However, this approach suffers from the relatively low-quality of graphene as well as the difficulty in layer control, thereby limiting its applications in high-performance electronic devices [12–14]. Chemical vapor deposition (CVD) method, which utilizes catalytic metal substrates as the growth template, is well-known to produce large-area, high-quality graphene films suitable for electronic applications [17, 18]. In CVD process, several factors can affect the properties of the grown graphene film. In particular, the electrical properties of graphene are highly dependent on the grain boundaries, which induce charge carrier scatterings and thus deteriorate the carrier mobility [19]. Since the grain boundaries mostly originate from the lattice mismatch during the growth process that is primarily influenced by the orientation of catalytic metal substrates, single-crystal metals like Ge (110), Cu (111), or Ni (111) have been investigated as the alternative growth template to avoid such grain boundaries, and high-quality single-crystalline graphene has been demonstrated which epitaxially grew onto those substrates [20–22]. However, the process involved with the production of single-crystalline materials is generally cost-intensive, which is not suitable for widespread industrial applications. Another strategy to improve the electrical properties of graphene is to increase the domain size, which can be achieved by suppressing the nucleation densities during the synthesis [23–25]. Such approaches include introducing oxygen gas, using enclosed metal catalysts, or resolidifying metallic substrates to create smooth surfaces during the growth stage. Among these various approaches in the CVD process, modifying the surface morphologies of catalytic growth substrates is considered one of the most viable approaches for obtaining high-quality graphene. Mechanical or chemical treatments are typically used in such approach which significantly reduces the impurities present in the metal catalysts, the major source of the nucleation center, leading to the improved carrier mobility [26–32]. In this work, we revisit the role of surface morphology of metal catalyst to the quality of CVD graphene using commercially available copper foil via simple chemical treatments and analyze the resulting physical properties. Chemical treatments on the growth substrates typically involve etching process, and we show that proper control of the metal catalyst pretreatment can be a simple yet facile approach to enhance the overall quality of CVD-grown graphene.

2. Experimental

2.1. Synthesis and Transfer of Graphene

Copper foil (99.8%, 25 μm thickness, 13,382, Alfa Aesar) was pretreated with 5.8% nitric acid (HNO₃) under varying exposure time from 0 s (reference sample) to 60 s and washed with D.I. water, followed by acetone and isopropyl alcohol (IPA). We note that the synthesis result of reference sample exhibited relatively low reproducibility compared with those samples synthesized from the pretreated metal catalysts, likely due to the impurities present on the metal catalyst surface. After the chemical treatment, the copper foil turned to slightly dark brown due to the oxidation. The copper foil was then loaded into the CVD chamber which was purged with Ar (100 sccm) for 10 min. After annealing the copper under H₂ (10 sccm) environment for 30 min at 1000°C, graphene synthesis was carried out with CH₄ (20 sccm) and H₂ (10 sccm) for 30 min (~30 mTorr). After the growth, the samples were rapidly cooled down to room temperature.

The as-grown graphene was transferred to SiO₂ (300 nm)/Si substrate via PMMA- (poly(methyl methacrylate)-) assisted transfer method. In brief, PMMA (9% in anisole) was spin-coated onto the graphene, which was dried in oven to remove the solvent. Copper foil was then etched away by ferric chloride solution, and the PMMA/graphene stack was thoroughly rinsed with mild hydrochloric acid and D.I. water. After transferring to the target substrate, PMMA was finally removed by acetone.

2.2. Characterization

Graphene channel was formed by standard photolithography and O₂ plasma etching process. Source and drain contacts (Ti/Au, 10/50 nm) were deposited by e-beam evaporation system. Heavily -doped Si substrate was used for the gate electrode, and the SiO₂ layer was working as the gate insulator. Source-drain voltage was fixed to 0.05 V, and gate voltage () sweep was from −100 V to 100 V to measure the source-drain currents (). The obtained curve is shown in Figure 1(b). Sheet resistance of graphene was measured by 4-point probe (CMT-SR2000N, Advanced Instrument Technology). Surface morphology of graphene was analyzed by optical microscopy (OM, Eclipse LV150, Nikon) and scanning electron microscopy (SEM, S-4800, Hitachi). Raman spectra were obtained from Alpha300R, WITec, with excitation wavelength at 532 nm. Transmittance was measured by UV-vis NIR spectroscopy (Carry 5000, Agilent).

(a)

(b)

3. Results and Discussion

In this work, low-pressure CVD with copper substrate was used for the graphene synthesis and nitric acid was applied to modify the surface morphology of the as-received copper foil (see Experimental). In general, HNO₃ reacts with copper and forms Cu(NO₃)₂ which is soluble in water as described in the following chemical reaction [26].

The overall reaction is dependent on the nitric acid treatment time, where the amount of Cu(NO₃)₂ increases with prolonged treatments which renders the copper surface morphology more rough and nonuniform as illustrated in Figure 2(a), leading to potential defect sites during the CVD process. The as-received pristine copper, with only conventional solvent rinsing such as acetone or isopropanol, typically exhibits bright regions due to the impurities naturally present in the copper (Figure 2(b)), which can be eliminated with such acid treatment. As shown in Figure 2(c), these bright spots are substantially reduced, and the surface becomes relatively smoother only after 30 s of acid treatment. However, extended chemical treatments typically result in highly nonuniform surface morphology due to the continued etching of the copper (Figure 2(d)). After 60 s of such reaction, the resulting morphology of copper becomes significantly rough compared to the pristine one despite the removal of impurities as shown in Figure 2(e).

(a)

(b)

(c)

(d)

(e)

To verify the effect of copper morphology to the growth of CVD graphene, surface morphologies of the as-transferred graphene grown on copper substrates with various pretreatment conditions were analyzed. Figure 3 shows the OM and SEM images of graphene sheets prepared under the same synthesis conditions and transferred onto the SiO₂ substrates. Several multilayer graphene domains are observed from the pristine copper substrate due to the large number of impurities which act as the nucleation center during the growth stage (red arrow, Figure 3(a)) [33]. The presence of typical wrinkle formation is also observed which originates from the difference in thermal expansion coefficients between the graphene and metal substrate as well as during the transfer process (blue arrow, Figure 3(b)) [34]. The bright spot is the polymer residue resulting from the transfer process (white arrow, Figure 3(b)) [35]. Such formation of multilayer graphene was significantly suppressed with copper substrate treated by 30 s of nitric acid as shown in Figures 3(b) and 3(f). However, multilayer graphene started to reappear with increasing acid treatment to 45 s due to the corresponding increase in roughness of the copper substrate (Figures 3(c) and 3(g)). Activated carbon atoms tend to aggregate more at the rough surface, which consequently increases the probability of multilayer formation [11, 25]. After 60 s treatment time, the presence of multilayer graphene even became comparable to that of the pristine copper case as shown in Figures 3(d) and 3(h). Figure 3(i) illustrates the distribution of monolayer graphene formation over the multilayer of the above, showing that monolayer graphene is mostly synthesized for the 30 s treatment case.

(a)

(b)

(c)

(d)

(e)

(f)

(g)

(h)

(i)

Optical transmittance of the respective graphene films was measured to evaluate the appearance of multilayer graphene (Supporting Information, Figure S1). Transmittance of 30 s sample was ~97.5% at 550 nm, similar to the theoretical value of monolayer graphene film (97.7%) [7]. This value was decreased to ~97.2 and ~96.5% with increasing acid treatments of 45 and 60 s, respectively, whereas the pristine copper sample showed ~96.9% transmittance likely due to the presence of multilayer graphene and light scattering induced from the rough graphene surface lowering the transmittance. These optical microscopy and transmittance results confirm that the formation of multilayer graphene is highly affected by the morphology of underlying catalytic growth substrate, which can be modulated and remedied via appropriate pretreatment conditions.

Next, Raman spectroscopy analysis was performed to investigate the overall quality of graphene sheets prepared from different types of copper substrates. All graphene films under study exhibit primarily monolayer characteristics with G and 2D peaks at ~1580 and 2680 cm⁻¹, respectively, and intensity ratio of nearly 2 as shown in Figure 4(a) [20]. We note that the intensity of D peak at ~1350 cm⁻¹, representing the degree of defects in sp² carbon domains, increases with acid treatment time, that is, the roughness of metal substrates (Figure 4(b)). We speculate that the increase of defect is related to multilayer graphene patches, which is formed by surface impurities or rough surfaces [36]. The value of full width at half maximum (FWHM) of 2D peak is another indicator commonly used to evaluate the quality of graphene, where the sharp peak is associated with the high-quality [37]. FWHM of 2D peak from 30 s sample is ~35 cm⁻¹ which is comparable to that of the mechanically exfoliated graphene, and gradually increases to ~43 and ~52 cm⁻¹ for 45 and 60 s cases, respectively, while the pristine sample being ~44 cm⁻¹ (Supporting Information, Figure S2) [38]. Arial defect analysis was also performed using Raman mapping. Figure S3 (Supporting Information) presents the intensity ratio mapping, which indicates the overall defects in the as-synthesized graphene increase with acid treatment time from 30 to 60 s. These results elucidate that the quality of CVD graphene is closely related to the starting morphology of the growth substrate.

(a)

(b)

The effect of defect sites in graphene on electrical properties was investigated via conductivity and field-effect mobility measurements. The sheet resistance of graphene film prepared from the aforementioned conditions was measured by the 4-point probe as shown in Figure 1(a). Consistent with previous results, the 30 s sample again showed the lowest sheet resistance of 290 ± 24 Ω·sq⁻¹, lower than that of the pristine graphene (420 ± 30 Ω·sq⁻¹), potentially due to the low defects present on the graphene which act as the charge carrier scattering sites lowering the overall electrical properties in the graphene film [19]. The sheet resistance was also increased to 427 ± 33 and 643 ± 45 Ω·sq⁻¹ with increasing acid treatment time (45 and 60 s, resp.) and the associated increase in the degree of defect sites. We also note that large deviations of sheet resistance values also occur with increasing chemical treatments to the metal substrate. We suspect this phenomenon is closely related to the nonuniformity of copper surface morphology originating from the prolonged etching process.

The effect of surface morphology of graphene on the electrical property was further analyzed from the field-effect mobility measurement. Graphene-based field-effect transistor (FET) was fabricated by standard photolithography with Ti (10 nm)/Au (50 nm) contacts formed by thermal evaporation as illustrated in Figure 1(b). Consistent with the sheet resistance measurement, electron mobility was highest with 30 s sample (1280 cm²·V⁻¹·s⁻¹) and decreased to 957 and 613 cm²·V⁻¹·s⁻¹ for 45 and 60 s cases, respectively, with the pristine sample being 1156 cm²·V⁻¹·s⁻¹ (Figure 1(b)). The charge neutral point of graphene is slightly p-doped which is well-matched with Raman data shown in Figure S2.

4. Conclusions

In this work, we showed that the quality of CVD-grown graphene is closely related to the underlying surface morphology of the metal catalyst growth template. Via simple and facile modification of the metal catalyst with commonly used acid, high-quality graphene film could be readily obtained, an important factor to consider for the widespread industrial applications of graphene-based electronic devices. The acid reacts with the metal catalyst by etching the metal surface, thus removing the impurities present which tend to deteriorate the overall quality of graphene. We believe that the simple yet effective approach proposed in this study, which enables the synthesis of high-quality graphene films with low defects, will benefit a variety of graphene-based functional devices such as thin-film transistors, optoelectronic devices, and flexible electronics.

Data Availability

The SEM data used to support the findings of this study are included within the article. The Raman spectrum data used to support the findings of this study are included within the article. The OM image data used to support the findings of this study are included within the article. The FET mobility data used to support the findings of this study are included within the article. The transmittance data used to support the findings of this study are included within the supplementary information file(s). The Raman mapping data used to support the findings of this study are included within the supplementary information file(s).

Conflicts of Interest

The authors declare that they have no conflicts of interest.

Acknowledgments

This work was supported by Basic Science Research Program through the National Research Foundation of Korea (NRF) funded by the Ministry of Education (2015R1D1A1A0105791) and the Ministry of Science and ICT (2016R1A2B4014762).

Supplementary Materials

Figure S1: transmittance data shows the reduction of optical transmission by multilayer graphene under each condition. Figure S2: the FWHM value of the Raman 2D peak supports that the graphene quality depends on the nitric acid treatment time. Figure S3: Raman mapping results support that as-synthesized graphene shows high uniformity. (Supplementary Materials)

References

K. S. Novoselov, A. K. Geim, S. V. Morozov et al., “Electric field effect in atomically thin carbon films,” Science, vol. 306, no. 5696, pp. 666–669, 2004.
View at: Publisher Site | Google Scholar
A. K. Geim and K. S. Novoselov, “The rise of graphene,” Nature Materials, vol. 6, no. 3, pp. 183–191, 2007.
View at: Publisher Site | Google Scholar
K. S. Novoselov, A. K. Geim, S. V. Morozov et al., “Two-dimensional gas of massless Dirac fermions in graphene,” Nature, vol. 438, no. 7065, pp. 197–200, 2005.
View at: Publisher Site | Google Scholar
Y. Zhang, Y. W. Tan, H. L. Stormer, and P. Kim, “Experimental observation of the quantum Hall effect and Berry’s phase in graphene,” Nature, vol. 438, no. 7065, pp. 201–204, 2005.
View at: Publisher Site | Google Scholar
T.-H. Han, Y. Lee, M. R. Choi et al., “Extremely efficient flexible organic light-emitting diodes with modified graphene anode,” Nature Photonics, vol. 6, no. 2, pp. 105–110, 2012.
View at: Publisher Site | Google Scholar
A. K. Geim, “Graphene: status and prospects,” Science, vol. 324, no. 5934, pp. 1530–1534, 2009.
View at: Publisher Site | Google Scholar
K. S. Novoselov, V. I. Fal′ko, L. Colombo, P. R. Gellert, M. G. Schwab, and K. Kim, “A roadmap for graphene,” Nature, vol. 490, no. 7419, pp. 192–200, 2012.
View at: Publisher Site | Google Scholar
F. Xia, T. Mueller, Y. M. Lin, A. Valdes-Garcia, and P. Avouris, “Ultrafast graphene photodetector,” Nature Nanotechnology, vol. 4, no. 12, pp. 839–843, 2009.
View at: Publisher Site | Google Scholar
H. Park, S. Chang, X. Zhou, J. Kong, T. Palacios, and S. Gradecak, “Flexible graphene electrode-based organic photovoltaics with record-high efficiency,” Nano Letters, vol. 14, no. 9, pp. 5148–5154, 2014.
View at: Publisher Site | Google Scholar
R. Raccichini, A. Varzi, S. Passerini, and B. Scrosati, “The role of graphene for electrochemical energy storage,” Nature Materials, vol. 14, no. 3, pp. 271–279, 2015.
View at: Publisher Site | Google Scholar
Y. Zhang, L. Zhang, and C. Zhou, “Review of chemical vapor deposition of graphene and related applications,” Accounts of Chemical Research, vol. 46, no. 10, pp. 2329–2339, 2013.
View at: Publisher Site | Google Scholar
S. Stankovich, D. A. Dikin, R. D. Piner et al., “Synthesis of graphene-based nanosheets via chemical reduction of exfoliated graphite oxide,” Carbon, vol. 45, no. 7, pp. 1558–1565, 2007.
View at: Publisher Site | Google Scholar
D. R. Dreyer, S. Park, C. W. Bielawski, and R. S. Ruoff, “The chemistry of graphene oxide,” Chemical Society Reviews, vol. 39, no. 1, pp. 228–240, 2010.
View at: Publisher Site | Google Scholar
X. Li, G. Zhang, X. Bai et al., “Highly conducting graphene sheets and Langmuir-Blodgett films,” Nature Nanotechnology, vol. 3, no. 9, pp. 538–542, 2008.
View at: Publisher Site | Google Scholar
P. Blake, P. D. Brimicombe, R. R. Nair et al., “Graphene-based liquid crystal device,” Nano Letters, vol. 8, no. 6, pp. 1704–1708, 2008.
View at: Publisher Site | Google Scholar
Y. Hernandez, V. Nicolosi, M. Lotya et al., “High-yield production of graphene by liquid-phase exfoliation of graphite,” Nature Nanotechnology, vol. 3, no. 9, pp. 563–568, 2008.
View at: Publisher Site | Google Scholar
C. Berger, Z. Song, T. Li et al., “Ultrathin epitaxial graphite: 2D electron gas properties and a route toward graphene-based nanoelectronics,” The Journal of Physical Chemistry B, vol. 108, no. 52, pp. 19912–19916, 2004.
View at: Publisher Site | Google Scholar
K. S. Kim, Y. Zhao, H. Jang et al., “Large-scale pattern growth of graphene films for stretchable transparent electrodes,” Nature, vol. 457, no. 7230, pp. 706–710, 2009.
View at: Publisher Site | Google Scholar
O. V. Yazyev and Y. P. Chen, “Polycrystalline graphene and other two-dimensional materials,” Nature Nanotechnology, vol. 9, no. 10, pp. 755–767, 2014.
View at: Publisher Site | Google Scholar
L. Gao, J. R. Guest, and N. P. Guisinger, “Epitaxial graphene on Cu(111),” Nano Letters, vol. 10, no. 9, pp. 3512–3516, 2010.
View at: Publisher Site | Google Scholar
Y. S. Dedkov, M. Fonin, U. Rudiger, and C. Laubschat, “Rashba effect in the graphene/Ni(111) system,” Physical Review Letters, vol. 100, no. 10, pp. 107602–107604, 2008.
View at: Publisher Site | Google Scholar
J.-H. Lee, E. K. Lee, W. J. Joo et al., “Wafer-scale growth of single-crystal monolayer graphene on reusable hydrogen-terminated germanium,” Science, vol. 344, no. 6181, pp. 286–289, 2014.
View at: Publisher Site | Google Scholar
Y. Hao, M. S. Bharathi, L. Wang et al., “The role of surface oxygen in the growth of large single-crystal graphene on copper,” Science, vol. 342, no. 6159, pp. 720–723, 2013.
View at: Publisher Site | Google Scholar
S. Chen, H. Ji, H. Chou et al., “Millimeter-size single-crystal graphene by suppressing evaporative loss of Cu during low pressure chemical vapor deposition,” Advanced Materials, vol. 25, no. 14, pp. 2062–2065, 2013.
View at: Publisher Site | Google Scholar
A. Mohsin, L. Liu, P. Liu et al., “Synthesis of millimeter-size hexagon-shaped graphene single crystals on resolidified copper,” ACS Nano, vol. 7, no. 10, pp. 8924–8931, 2013.
View at: Publisher Site | Google Scholar
S. M. Kim, A. Hsu, Y. H. Lee et al., “The effect of copper pre-cleaning on graphene synthesis,” Nanotechnology, vol. 24, no. 36, pp. 365602–365608, 2013.
View at: Publisher Site | Google Scholar
M.-S. Kim, J.-M. Woo, D.-M. Geum, J. R. Rani, and J. H. Jang, “Effect of copper surface pre-treatment on the properties of CVD grown graphene,” AIP Advances, vol. 4, no. 12, pp. 127107–127111, 2014.
View at: Publisher Site | Google Scholar
G. Zhao, X. Li, M. Huang et al., “The physics and chemistry of graphene-on-surfaces,” Chemical Society Reviews, vol. 46, no. 15, pp. 4417–4449, 2017.
View at: Publisher Site | Google Scholar
A. Ibrahim, G. Nadhreen, S. Akhtar, F. M. Kafiah, and T. Laoui, “Study of the impact of chemical etching on Cu surface morphology, graphene growth and transfer on SiO₂/Si substrate,” Carbon, vol. 123, pp. 402–414, 2017.
View at: Publisher Site | Google Scholar
A. T. Murdock, C. D. van Engers, J. Britton et al., “Targeted removal of copper foil surface impurities for improved synthesis of CVD graphene,” Carbon, vol. 122, pp. 207–216, 2017.
View at: Publisher Site | Google Scholar
Y. H. Zhang, Z. Y. Chen, X. M. Ge et al., “A waterless cleaning method of the Cu foil for CVD graphene growth,” Materials Letters, vol. 211, pp. 258–260, 2018.
View at: Publisher Site | Google Scholar
D. Senyildiz, O. T. Ogurtani, and G. Cambaz Buke, “The effects of acid pretreatment and surface stresses on the evolution of impurity clusters and graphene formation on Cu foil,” Applied Surface Science, vol. 425, pp. 873–878, 2017.
View at: Publisher Site | Google Scholar
H. Wang, G. Wang, P. Bao et al., “Controllable synthesis of submillimeter single-crystal monolayer graphene domains on copper foils by suppressing nucleation,” Journal of the American Chemical Society, vol. 134, no. 8, pp. 3627–3630, 2012.
View at: Publisher Site | Google Scholar
Y. Zhang, L. Gomez, F. N. Ishikawa et al., “Comparison of graphene growth on single-crystalline and polycrystalline Ni by chemical vapor deposition,” The Journal of Physical Chemistry Letters, vol. 1, no. 20, pp. 3101–3107, 2010.
View at: Publisher Site | Google Scholar
A. Pirkle, J. Chan, A. Venugopal et al., “The effect of chemical residues on the physical and electrical properties of chemical vapor deposited graphene transferred to SiO₂,” Applied Physics Letters, vol. 99, no. 12, pp. 122108–122111, 2011.
View at: Publisher Site | Google Scholar
Z. Han, A. Kimouche, D. Kalita et al., “Homogeneous optical and electronic properties of graphene due to the suppression of multilayer patches during CVD on copper foils,” Advanced Functional Materials, vol. 24, no. 7, pp. 964–970, 2014.
View at: Publisher Site | Google Scholar
A. Ismach, C. Druzgalski, S. Penwell et al., “Direct chemical vapor deposition of graphene on dielectric surfaces,” Nano Letters, vol. 10, no. 5, pp. 1542–1548, 2010.
View at: Publisher Site | Google Scholar
S. Lee, K. Lee, and Z. Zhong, “Wafer scale homogeneous bilayer graphene films by chemical vapor deposition,” Nano Letters, vol. 10, no. 11, pp. 4702–4707, 2010.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2018 Junghyun Lee et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

2208

Downloads

1203

Citations