Prospect of <i>Pongamia pinnata</i> (Karanja) in Bangladesh: A Sustainable Source of Liquid Fuel

Halder, P. K.; Paul, N.; Beg, M. R. A.

doi:https://doi.org/10.1155/2014/647324

Journal of Renewable Energy

On this page

Abstract Introduction References Copyright Related Articles

Review Article | Open Access

Volume 2014 | Article ID 647324 | https://doi.org/10.1155/2014/647324

Prospect of Pongamia pinnata (Karanja) in Bangladesh: A Sustainable Source of Liquid Fuel

P. K. Halder,¹N. Paul,²and M. R. A. Beg³

Academic Editor: Adnan Parlak

Received17 Aug 2014

Accepted25 Nov 2014

Published18 Dec 2014

Abstract

Energy is the basic requirement for the existence of human being in today’s digital world. Indigenous energy of Bangladesh (especially natural gas and diesel) is basically used in power generation and depleting hastily to meet the increasing power demand. Therefore, special emphasis has been given to produce alternative liquid fuel worldwide to overcome the crisis of diesel. Pongamia pinnata (karanja) may be an emerging option for providing biooil for biodiesel production. Although karanja biooil has been used as a source of traditional medicines in Bangladesh, it can also be used for rural illumination. This paper outlines the medical and energy aspects of Pongamia pinnata. It has been assessed that Bangladesh can utilize about 128.95 PJ through Pongamia cultivation in unused lands. The paper reviews the potentiality of Pongamia pinnata as a source of biodiesel and its benefits in Bangladesh. The paper also revives that, about 0.52 million tons of biodiesel can be produced only utilizing the unused lands per year in sustainable basis as it reduces CO₂, CO, HC, and NO_x emission compared to pure diesel.

1. Introduction

Pongamia pinnata (L.) Pierre (family: Leguminosae) is an important nonedible minor oilseed tree [1] that grows in the semiarid regions. It is probably originated from India and grows naturally in India, Bangladesh, Pakistan, Malaysia, Thailand, Vietnam, Australia, Florida, and Sri Lanka and also in northeastern Australia, Fiji, Japan, and the Philippines [2]. In the USA Pongamia pinnata was introduced into Hawaii in the 1960s by Hillebrand [3]. In Bangladesh it is popularly known as Koroch. It is an adaptable tree for tropical and subtropical regions which requires excellent drainage and a sunny location. In India, billions of karanja trees exist where karanja trees are cultivated commercially and seed is collected from December to April. However, in Bangladesh it is not cultivated commercially yet. In India, one person can collect 180 kg of seeds in 8 hours of a day where the collection cost is INR 4 per kg [4].

1.1. Classification

Kingdom: Plantae Division: Magnoliophyta Class: Magnoliopsida Order: Fabales Family: Leguminosae Genus: Pongamia Species: pinnataSource: [5]

1.2. Botanic and Chemical Characteristics

Pongamia pinnata (chromosome number: 22) is a very fast-growing medium size plant with an average height of 30–40 feet and spreads canopy for casting moderate shade. Pongamia pinnata has a varied habitat distribution and can grow in a wide range of conditions. It can grow in various types of soil like salty, alkaline, hefty clay, sandy, stony, and waterlogged soils and also shows high tolerance against drought bearing temperature up to 50°C. The trunk is usually short with a diameter of more than 1.64 feet. The leaves are comprised of 5–7 leaflets 5–10 cm long and 4–6 cm wide which are arranged in 2-3 pairs. On the other hand, the bark is thin and gray to grayish-brown in color with yellow on the inside where the tap root is thick and long [6]. Pea-shaped flowers are generally 15–18 mm long and pink, light purple, or white in color [5]. The elliptical pods consist of single seed inside the thick walled pod shell which are 3–6 cm long and 2-3 cm wide as shown in Figure 1. The pods are dried in sun and the seeds are extracted by thrashing. Seeds are light brown in color with a length of 1.0–1.5 cm [5]. About 9–90 kg of seed pods can be obtained from one tree which yields up to 40% oil per seed and around 50% of this oil is C 18 : 1, which is considered as suitable for biodiesel production [7]. Another study shows that about 8–24 kg of kernels is obtained from one tree which yields 30–40% oil [8, 9]. The seeds naturally exist for about 6 months [10]. The air dried kernels consist of 19% moisture, 27.5% oil, 17.4% protein, 6.6% starch, 7.3% crude fiber, and 2.3% ash [9, 10].

(a)

(b)

(c)

(d)

(e)

1.3. Cultivation of Pongamia pinnata in Bangladesh

Pongamia pinnata is one of the few nitrogen-fixing trees which are predominantly cultivated easily through seeds. The genetic diversity has been conserved through storage of seeds which is the most common conventional and economical method [11, 12]. The growth of Pongamia pinnata is seen from sea level to an altitude of around 1200 m and an optimal annual rainfall of 500 to 2500 mm. The trees are naturally distributed along the coasts and riverbanks in lands and are native to the Asian subcontinent. Furthermore, these are also cultivated along roadsides, canal banks, and open farmlands. About 60 × 60 × 60 cm³ pits are appropriate for planting where the spacing between rows should be 5 m and plant to plant distance is recommended to be 4 m [13]. Generally, three irrigations may be given in a year for better growth and development of the plants.

A simple and reliable method selection is the primary step for the successful propagation of Pongamia pinnata tree. However, coppicing and pollarding are considered as fruitful ways of agroforestry management practices for Pongamia pinnata [14]. The successful propagation methods of Pongamia pinnata are comprised of through seeds, through cuttings, and through layering and drafting. It can be easily propagated through seeds by direct sowing both in the nursery bed and in the polybags. However, seeds can be effectually used for mass propagation of Pongamia pinnata [15, 16]. A study shows the direct relationship between seed size and germination efficiency [17]. It can also be propagated through semihard wood stem cutting. Moreover, air layering and cleft drafting is the other process for successful propagation. The unused and marginal lands of Bangladesh can be brought under Pongamia pinnata cultivation to meet the need of liquid fuel.

2. Versatile Applications of Pongamia pinnata

Historically, all the parts of Pongamia pinnata like flower, seed, leaf, root, and so forth have been utilized as a source of traditional medicines, animal fodder, green manure, timber, fish poison, and fuel in India, Bangladesh, and other neighbouring regions.

2.1. Pongamia pinnata Wood

Traditionally, Pongamia pinnata wood is used as fuel in rural areas in Bangladesh. It has no distinct heartwood and varies from white to yellowish-grey color with a calorific value of 19.32 MJ/kg. The wood is considered as low quality timber due to its softness, tendency to split during sowing, and vulnerability to insect attack [6]. Therefore, the wood is used for stove top fuels, poles and ornamental carvings [18], cabinet making, cart wheels, posts [19], agricultural implements, tool handles, and some usual activities [20]. The ash produced from burning wood is used for dyeing [21].

2.2. Pongamia pinnata Oil

Oil is considered the most noteworthy product obtained from the Pongamia pinnata seeds. It is a thick, yellow or reddish-brown oil which has a calorific value of 40.756 MJ/kg, extracted through expeller, solvent extraction, and so forth. The oil is nonedible, acrimonious in taste, and offensive in smell and is used for commercial processes maybe as medicine and lamp fuel and for the production of biodiesel. Furthermore, it is used as fuel for cooking, as a lubricant, as water-paint binder, in leather dressing, and in soap-making, candles, and tanning industries [22]. Crude karanja oil (CKO) has also the application in body oils, salves, lotions, hair tonics, shampoos, and pesticides [23].

2.3. Pongamia pinnata as Fodder and Feed

The Pongamia pinnata leaves contain 43% dry matter, 18% crude protein, 62% neutral detergent fiber, and in vitro dry matter digestibility of 50% and are eaten by cattle and readily consumed by goats. The trees have a significant value in arid regions, however the use is not common. The deoiled cakes could be used as poultry feed and cattle feed [24].

2.4. Pongamia pinnata as a Medicine

Even though all parts of the plant are noxious, the flowers and fruits along with the seeds are used in many traditional medicines. Flowers are used to treat bleeding hemorrhoids whereas fruits aid treatment of abdominal tumors, ulcers, and hemorrhoids. Seed powder reduces fever and helps in treating bronchitis and whooping cough. On the other hand, leaves juices aid in treatment of leprosy, gonorrhea, diarrhea, flatulence, coughs, and colds. Besides, bark relieves coughs and colds and mental disorder. Root is used as a toothbrush for oral hygiene while root juice is used to clean ulcers [25]. Pongamia pinnata oil is styptic, anthelmintic, and good in leprosy, piles, ulcers, chronic fever, liver pain [26], and rheumatism arthritis scabies [27].

2.5. Seed Cake as Fertilizer

Seed cake, a byproduct of oil extraction, is bitter and unfit for animal feed. It is rich in protein and nitrogen and is used as green manure to fertilize the land. It is also used as a pesticide, especially against nematodes. Besides, the seed cake can be used for biogas production.

2.6. Soil Erosion

Pongamia pinnata trees are usually planted along the highways, roads, and canals to stop soil erosion. The plants develop a lateral network of roots for controlling soil erosion and binding sand dunes [28]. Thus, karanja plantation can reduce soil erosion with many other benefits as described.

3. Pongamia pinnata: A Viable Alternative to Liquid Fuel

Diesel and kerosene are considered as major liquid fuel and account for 90% of the country’s total fuel. Thus Pongamia pinnata, a source of nonedible vegetable oil, is considered as the most significant to use as an alternative liquid fuel due to its nonfood use and less expense for production.

3.1. Alternative Oil for Kerosene

Kerosene, the most common liquid fuel, is traditionally used in rural illumination and for cooking purpose in Bangladesh. In the country, only about 49% of total population has access to electricity and has only few facilities to use LPG for cooking purpose. Therefore, population of remote and coastal areas use kerosene lamp and hurricane for lighting and the poor people of those villages use biomass burning stove for cooking and heating purposes. On the contrary, population of urban and semiurban areas use kerosene stove for cooking where LPG and biomass are not available. In the fiscal year 2012, the country has consumed about 508.5 million liters of kerosene as shown in Figure 2 [29]. The country imported about 124.28 million liters of kerosene in 2010 which was 24.41% of total consumed kerosene account as 509.24 million liters. Bangladesh Petroleum Corporation (BPC) has to pay USD 134.53 per barrel to import kerosene and jet fuel. BPC has planned to import 0.267 million tons of kerosene, jet fuel, and octane during the fiscal year 2013-2014. BPC is incurring loss of BDT 14–16 per liter for kerosene though the price is hiking.

Increasing price (68 BDT/liter) of kerosene is trending in reduction of kerosene consumption and encouraging finding out alternative liquid fuel option to kerosene. Furthermore, the reserve in the country is very limited. Hence, the consumption rate of kerosene is reduced by 37.42% from fiscal year 2001 to fiscal year 2012 though the demand is high. Recently, several techniques have been adapted to produce liquid fuels from nonedible seeds in renewable basis. Table 1 shows the comparison of some seed oils to kerosene. Kerosene has a calorific value of 46.2 MJ/kg with a density of 780–810 kg/m³ [30] and a maximum distillation temperature of 205°C at the 10% recovery point. Among the seed oils Pongamia pinnata and Jatropha curcas have the competitive calorific value though the density is higher than kerosene. Pongamia pinnata has a calorific value of 40.756 MJ/kg [31] which is higher than other seed oils and slightly lower than kerosene.

Nonedible seed oil or straight vegetable oil (SVO) is rare to use in lighting and cooking due to its high density and viscosity. Hence, use of biooil in traditional kerosene stove for cooking and in wick-fed lamp for lighting shows the poor result due to its low capillary action. A recent study shows the effective way to use the crude karanja oil (CKO) for cooking purpose [31]. Use of karanja oil in gravity stove where fuel is feed under gravity shows the promising result as indicated in Figure 3 [31]. The oil also shows attractive heating performance in it though the method is not commercially well-known. Therefore, karanja oil may be an effective option for an alternative to kerosene.

3.2. Pongamia pinnata Biodiesel as an Alternative to Diesel

Diesel is an indispensable fuel generally used in industrial and agricultural goods transports, in vehicles, and in diesel tractors and pumps for irrigation. Bangladesh is a developing country with a total population of 150 million. The population of the country is growing rapidly which is creating the petrodiesel utilization sector.

In Bangladesh demand of diesel fuel is increasing day by day; hence it is necessary to find renewable alternative to diesel immediately. Not only Bangladesh’s but also the world’s diesel requirement is growing firstly. Bangladesh consumed about 4021.65 million liters of diesel in 2012 where the neighboring country India consumed about 66 million tons in 2011-12 [32]. Figure 4 shows the increasing trend of diesel consumption pattern in Bangladesh. The country has planned to import about 3 million tons of diesel where the country’s average import is about 2.4 million tons [33]. The import price of diesel fuel is USD 133 per barrel and the government is incurring loss of BDT 13–15 per liter for diesel though the price has been increased to BDT 68 per liter.

Considering the increasing prices and environmental aspects of fossil fuels especially diesel fuel, interests have been revived around the world to find renewable substitute for fossil fuels. Biodiesel obtained from vegetable oils is considered the most suitable alternative to diesel around the world [34]. World’s biofuel production has been growing rapidly to meet the increasing demand of petrodiesel and has reached 107.5 billion liters in 2011 comprising 21.4 billion liters of biodiesel and 86.1 billion liters of ethanol as shown in Figure 5 [35]. The USA, Germany, Brazil, Argentina, and France are the world’s top biodiesel producer countries where the USA has increased the biodiesel production mainly from soybeans by 159% to nearly 3.2 billion liters in 2011 [35]. However, Indonesia, Malaysia, Thailand, the Philippines, and India are the largest biofuel producing countries in Asia [36].

Various vegetable oils like coconut, jatropha, karanja, rapeseed, peanut, sunflower, and soybean have been used to produce biofuel for the last few years [37]. In the year 1910, Dr. Rudolf Diesel first introduced peanut oil as fuel in compression ignition (CI) engine [38]. However, high viscosity, low volatility, and polyunsaturated character of SVO are the foremost problems of using it as substitute for diesel in CI engine [39]. The processed vegetable oil (biodiesel) obtained through transesterification solves the problems associated with SVO and can be used in CI engine [40]. Numerous researchers have showed the effective use of plant oil derived biodiesel as fuel in CI engines [39, 41–43].

Of the plant seeds, karanja is considered the most attractive source for biodiesel production due to its renewable, safe, and nonpollutant nature. Furthermore, it is cost-effective and diverse feedstock for biodiesel due to its higher recovery and quality than other seeds, no direct competition with edible food crops and with current farmland. The properties of biodiesel prepared from karanja oil are presented in Table 2.

Some researchers have tested the suitability of Pongamia pinnata oil as SVO in CI engine [44, 45]. Other studies have shown that the potentiality of Pongamia pinnata oil as a source of raw material for the production of biodiesel is well established [46–51]. However, some of them have mentioned the suitability of CKO compared to jatropha due to its less toxicity and economy [48–50]. In Bangladesh, a study has indicated the biodiesel production from CKO and its effective use in CI engine as diesel substitute [52]. Karanja biodiesel has no corrosion on piston metal whereas jatropha biodiesel has slight corrosive effect.

It has been estimated that approximately 550 karanja trees are planted in one hectare which yield about 7.7 tons of seeds and 1.8095 tons of oil [53]. It is considered that about 90% biodiesel is obtained through transesterification of karanja oil [54]. Hence, one hectare yields about 1.62855 tons of biodiesel. Bangladesh has a total marginal length of 4246 km comprised of 4053 km with India and 193 km with Myanmar [55]. Moreover, the country has about 0.32 million hectares of unused land [56]. Considering plant to plant spacing as 4 m, only marginal land of the country has a potentiality of planting about 1061501 plants which yield 3.49 kilotons of oil. Accordingly, expected biodiesel production in Bangladesh from karanja oil is estimated to be about 0.52 million tons per year utilizing the unused land. Hence, the country can reduce the import of diesel fuel by 21.67% which will save approximately 508.53 million USD. Therefore, karanja can play an emerging role in the sector of liquid fuel.

3.2.1. Need of Biodiesel in Bangladesh Context

Liquid fuel especially diesel is the key input for the development of each and every sector in developing countries like Bangladesh. Excessive requirement of diesel in transport and power sector in Bangladesh forces to find alternative option. Biodiesel is considered as the prominent one due to the following reasons:(i)It is needed for rapid depletion of fossil fuels and hikes in oil prices.(ii)Biodiesel is a renewable and less polluting source of energy.(iii)It is considered as ecofriendly and nontoxic.(iv)Biodiesel industry can strengthen the domestic, rural, and agricultural economy.(v)Biodiesel has positive energy balance ratio and can be used in CI engines.(vi)It reduces import of petroleum products.

4. Energy Assessment of Pongamia pinnata

Like other trees, karanja has an enormous energy potential which comprises the energy of wood, energy of pod shell, energy of biodiesel, energy of glycerin, and energy of seed cake. It has been estimated that about 5 tons of fuel wood can be obtained from one hectare per year which has a calorific value of 19.25 MJ/ton [57]. One hectare can provide about 7.7 tons of seeds which yield 1.8095 tons of oil and 5.8905 tons of seed cake [53]. Furthermore, the seed cake can be utilized for biogas production and biogas slurry can be used as organic fertilizer. Considering 90% conversion factor about 1.62855 tons of biodiesel is estimated from oil and the remaining byproduct is glycerin which accounts for 0.18095 tons as shown in Table 3. Besides, one hectare produces about 8.65 tons of pod shell [58]. Total energy content of karanja per hectare was calculated by considering the calorific value of each item and estimated to be about 402.95 GJ/year. Accordingly, Bangladesh can utilize 128.95 PJ energy per year from karanja which is equivalent to 4.4 million tons of coal.

5. Engine Performance and Emission Analysis

In recent days, global warming is the foremost concern endorsed due to the large-scale use of fossil fuels. The use of vegetable oil ester which is biodiesel in CI engine shows the promising engine performance comparable with diesel fuel [59]. Besides, biodiesel is basically sulfur-free and emits considerably fewer particulates, hydrocarbons, and less carbon monoxide than conventional diesel fuel [32]. However, emissions of NO_x from biodiesel are slightly higher than diesel in CI engines [60]. Table 4 presents the summery of various emission statuses from biodiesel.

Many researchers have investigated the performance and emission characteristics of biodiesel in CI engine as a substitute for diesel fuel. Reduction in the power of CI engine due to the loss of heating value of biodiesel was reported in [61–79]. Some other researcher found no substantial variation between diesel and biodiesel performance in CI engine [80–84]. However, astonishing power increase due to use of pure biodiesel was noticed by [85, 86]. Karanja methyl ester (KOME) B100 which reduces the brake thermal efficiency of CI engine was investigated by some researcher [87, 88]. Minor difference between the engine efficiency of using KOME and pure diesel was found in [89, 90]. Surprisingly, high brake thermal efficiency due to use of B20 KOME was observed by [91]. However, a study in Bangladesh showed the most promising result in CI engine performance with B25 and B100 KOME competitive to pure diesel as presented in Figure 6 [52].

Emission from CI engine is a concerning matter which is reduced by using biodiesel as substitute for pure diesel. Researches [63, 64, 73, 82, 83, 92, 93] revealed the reduction in CO₂ emission from CI engine with use of biodiesel. However, some researchers found an increase of CO₂ emission [67, 94–98], while, in literatures [73, 82], it was reported that biodiesel resulted in about 50–80% reduction in CO₂ emissions compared to diesel fuel. Table 5 presents the comparative summary of CO₂ emission from various fuels.

KOME biodiesel which resulted in reduction of CO₂ emission was presented in [90, 91] as shown in Figure 7 [91]. Karanja oil reduces the overall effect of CO₂ emissions by about 75% as it absorbs about 30 tons of CO₂ per hectare per year [99].

Many literatures [61–64, 66–71, 73, 81, 83, 84, 93–95, 100–113] reported the decreasing nature of CO emission from biodiesel as CI engine fuel, whereas some researchers [96, 107, 114–118] observed the rise of CO emission. It was found that B100 KOME biodiesel reduces about 73–94% CO emission [66]. Besides, [52, 87, 89] agreed that KOME biodiesel reduces the CO emission as illustrated in Figure 8 [52]. Numerous studies also showed that biodiesel reduces PM emission in CI engine [62–69, 80–83, 85, 94, 95, 101–107, 119–123]. On the contrary, few reported the increase of PM emission [61, 100, 114–116, 124, 125].

It is predominantly investigated that use of biodiesel instead of pure diesel resulted in reduction of HC emission [63, 65, 67–69, 80–82, 84–86, 95, 100–105, 107–112, 117, 118, 121–123, 126, 127]. However, a very few number of researchers noticed the increase of HC emission [96, 114, 115]. Approximately 63% of HC emission was reduced by using biodiesel compared to pure diesel fuel [97]. KOME biodiesel reduces the HC emission in CI engine [87, 89, 91] as shown in Figure 9 [87].

In many studies [62, 63, 65, 67–73, 80, 83, 85, 86, 101, 107, 109–113, 117, 120, 126, 128–130], it was reported that biodiesel causes the increase in NO_x emission. On the other hand, reduction of NO_x emission was presented in [61, 64, 66, 81, 92, 97, 100, 103, 105, 114, 115, 118, 123, 126, 131–136]. However, [52] observed a maximum of 15% increase in NO_x emissions for B100 KOME as presented in Figure 10 [52]. Besides, [87, 91] noticed the increasing trend wherein [89] noticed the decreasing trend of NO_x emission.

6. Rural Development in Bangladesh through Pongamia pinnata

The Pongamia pinnata system can play a pivotal role for the socioeconomic development of rural areas in Bangladesh. Cultivation of Pongamia pinnata covers the following main aspects of rural developments in the country:(i)creation of job sector for rural unemployed people basically for women,(ii)increase of agricultural works like planting, weeding, and oil extraction,(iii)opportunity of developing small size rural industry,(iv)reduction of uncultivated lands through Pongamia pinnata plantation,(v)increase of per capita income of rural people through biodiesel production,(vi)energy supply for rural illumination and fuel for small stationery engines,(vii)reduction in fossil fuel importing bill through biodiesel production.

7. Concluding Remarks

Pongamia pinnata, a versatile resource, shows the promising properties for the medical and biodiesel production industry. Many countries in the world are producing biodiesel in order to replace the fossil diesel fuel. Bangladesh has a considerable potential of biodiesel production from karanja as it has high growth rate in Bangladesh. The country has about 0.32 million hectares of unused lands which yield about 0.52 million tons of biodiesel per year and can reduce import of diesel fuel approximately by 21.67%. Besides, on energy basis country’s unused lands provide about 128.95 PJ from karanja equivalent to 4.4 million tons of coal. However, the country has not started commercial cultivation of Pongamia yet. Furthermore, Pongamia biodiesel is environmentally friendly and causes fewer CO₂, CO, HC, and NO_x emission in CI engine as an alternative fuel to diesel. Karanja biodiesel blends of 20% with fossil diesel fuel produce approximately 70% less pollution. In conclusion, Bangladesh should take initiative to cultivate Pongamia and other nonedible seed plants for biodiesel production.

Conflict of Interests

The authors declare that there is no conflict of interests regarding the publication of this paper.

References

Council of Scientific and Industrial Research, Wealth of India-Raw Material, vol. 8, Council of Scientific and Industrial Research, New Delhi, India, 1965.
N. Mukta and Y. Sreevalli, “Propagation techniques, evaluation and improvement of the biodiesel plant, Pongamia pinnata (L.) Pierre-A review,” Industrial Crops and Products, vol. 31, no. 1, pp. 1–12, 2010.
View at: Publisher Site | Google Scholar
World Agroforestry Centre (WAC), 2013, http://www.worldagroforestrycentre.org/sea/products/afdbases/af/asp/SpeciesInfo.asp?SpID=1332#Addinfo.
Satish Lele, http://www.svlele.com/karanj.htm.
S. Sangwan, D. V. Rao, and R. A. Sharma, “A review on Pongamia Pinnata (L.) Pierre: a great versatile leguminous plant,” Nature and Science, vol. 8, no. 11, pp. 130–139, 2010.
View at: Google Scholar
Petroleum Conservation Research Association, “National Biofuel Centre,” 2013, http://www.pcra-biofuels.org/Karanj.htm.
View at: Google Scholar
The ARC Centre of Excellence for Integrative Legume Research (CILR), 2013, http://www.cilr.uq.edu.au/UserImages/File/Posters/Pongamia%20Biodiesel%20Poster.pdf.
V. Lakshmikanthan, “Tree Borne Oilseeds. Directorate of Nonedible Oils & Soap Industry, Khadi & Village Industries Commission,” Mumbai, India, 1978.
View at: Google Scholar
N. V. Bringi, Non-Traditional Oilseeds and Oils in India, Oxford & IBH, New Delhi, India, 1987.
The National Oilseed and Vegetable Oils Development Board (NOVOD), “Commercial exploitation of Simarouba glauca,” in Proceedings of the Workshop on Strategies for Development of Tree-Borne Oilseeds and Niger in Tribal Areas, Gurgaon, India, 1995.
View at: Google Scholar
E. H. Roberts, Ed., In Viability of Seeds, Chapman and Hall, London, Uk, 1972.
T. D. Hong and R. H. Ellis, A Protocol to Determine Seed Storage Behaviour, IPGRI Technical Bulletin 1, International Plant Genetic Resources Institute, Rome, Italy, 1996.
National Oilseeds and Vegetable Oils Development (NOVOD) Board, 2013.
C. M. Misra and S. L. Singh, “Coppice regeneration of Cassia siamea and Pongamia pinnata,” Nitrogen Fixing Tree Research Reports, vol. 7, no. 7, p. 4, 1989.
View at: Google Scholar
A. K. Handa and D. Nandini, “An alternative source of biofuel, seed germination trials of Pongamia pinnata,” International Journal of Forest Usufructs Management, vol. 6, no. 2, pp. 75–80, 2005.
View at: Google Scholar
K. P. Singh, G. Dhakre, and S. V. S. Chauhan, “Effect of mechanical and chemical treatments on seed germination in Pongamia glabra L,” Seed Research, vol. 33, no. 2, pp. 169–171, 2005.
View at: Google Scholar
V. Manonmani, K. Vanangamudi, and R. S. Vinaya Rai, “Effect of seed size on seed germination and vigour in Pongamia pinnata,” Journal of Tropical Forest Science, vol. 9, no. 1, pp. 1–5, 1996.
View at: Google Scholar
D. K. Das and M. K. Alam, Trees of Bangladesh, Forest Research Institute, Chittagong, Bangladesh, 2001.
NAS, Irewood Crops: Shrub and Tree Species for Energy Production, vol. 1, National Academy of Sciences, Washington, DC, USA, 1980.
Government of India (GOI), Troup's The Silviculture of Indian Trees, vol. 4, Leguminosae. Government of India Press, Nasik, India, 1983.
O. N. Allen and E. K. Allen, The Leguminosae, The University of Wisconsin Press, 1981.
J. H. Burkill, “Dictionary of economic products of the Malay penimsula,” The Indian Journal of Hospital Pharmacy, vol. 15, no. 6, pp. 166–168, 1996.
View at: Google Scholar
V. Kesari, A. Das, and L. Rangan, “Physico-chemical characterization and antimicrobial activity from seed oil of Pongamia pinnata, a potential biofuel crop,” Biomass and Bioenergy, vol. 34, no. 1, pp. 108–115, 2010.
View at: Publisher Site | Google Scholar
Shodhganga@INFLIBNET Centre, http://shodhganga.inflibnet.ac.in/bitstream/10603/3207/5/05_chapter%201.pdf.
Pongamia pinnata, 2013.
P. K. Warrier, V. P. K. Nambiar, and C. Ramakutty, Indian Medicinal Plants, Orient Longman, Madras, India, 1995.
G. Prasad and M. V. Reshmi, A Manual of Medicinal Trees, Propagation Methods. Foundation for Revitalization for Local Health Tradition, Agrobios India, 2003.
“Pongamia pinnata,” http://bioweb.uwlax.edu/bio203/2011/bedard_emil/history_adaptation.htm.
View at: Google Scholar
Bangladesh Petroleum Corporation (BPC), http://www.bpc.gov.bd/contactus.php?id=22.
C. Collins, “Implementing phytoremediation of petroleum hydrocarbons,” in Methods in Biotechnology, vol. 23, pp. 99–108, Humana Press, New York, NY, USA, 2007.
View at: Google Scholar
P. K. Halder, M. U. H. Joardder, M. R. A. Beg, N. Paul, and I. Ullah, “Utilization of Bio-Oil for cooking and lighting,” Advances in Mechanical Engineering, vol. 2012, Article ID 190518, 5 pages, 2012.
View at: Publisher Site | Google Scholar
P. Mahanta and A. Shrivastava, Technology Development of Bio-Diesel as an Energy Alternative, Department of Mechanical Engineering Indian Institute of Technology, 2004.
M. N. Nabi, M. S. Akhter, and K. M. F. Islam, “Prospect of biodiesel production from Jatropha curcas, a promising non edible oil seed in Bangladesh,” in Proceedings of the International Conference on Mechanical Engineering (ICME '07), Paper no. ICME07-TH-06, Dhaka, Bangladesh, 2007.
View at: Google Scholar
B. K. Barnwal and M. P. Sharma, “Prospects of biodiesel production from vegetable oils in India,” Renewable and Sustainable Energy Reviews, vol. 9, no. 4, pp. 363–378, 2005.
View at: Publisher Site | Google Scholar
“Renewables 2012,” Global Status Report REN21, 2012.
View at: Google Scholar
A. Zhou and E. Thomson, “The development of biofuels in Asia,” Applied Energy, vol. 86, pp. S11–S20, 2009.
View at: Publisher Site | Google Scholar
N. Sazdanoff, Modeling and simulation of the algae to biodiesel fuel cycle [Undergraduate thesis], Department of Mechanical Engineering, College of Engineering, The Ohio State University, 2006.
S. N. Bobade and V. B. Khyade, “Detail study on the properties of Pongamia pinnata (Karanja) for the production of biofuel,” Research Journal of Chemical Sciences, vol. 2, no. 7, pp. 16–20, 2012.
View at: Google Scholar
C. E. Goering, A. W. Schwab, M. J. Daugherty, E. H. Pryde, and A. J. Heakin, “Fuel properties of eleven vegetable oils,” ASAE Paper Number 813579, St. Joseph, Mich, USA, ASAE, 1981.
View at: Google Scholar
M. Senthil Kumar, A. Ramesh, and B. Nagalingam, “Investigations on the use of Jatropha oil and its methyl ester as a fuel in a compression ignition engine,” Journal of the Institute of Energy, vol. 74, no. 498, pp. 24–28, 2001.
View at: Google Scholar
A. K. Agarwal, “Vegetable oils versus diesel fuel: development and use of biodiesel in a compression ignition engine,” TIDE, vol. 83, pp. 191–204, 1998.
View at: Google Scholar
S. Sinha and N. C. Misra, “Diesel fuel alternative from vegetable oils,” Chemical Engineering World, vol. 32, no. 10, pp. 77–80, 1997.
View at: Google Scholar
A. Shaheed and E. Swain, “Combustion analysis of coconut oil and its methyl esters in a diesel engine,” Proceedings of the Institute of Mechanical Engineers, vol. 213, no. 5, pp. 417–425, 1999.
View at: Google Scholar
U. Shrinivasa, “A viable substitute for diesel in rural India,” Current Science Magazine, vol. 80, no. 12, pp. 1483–1484, 2001.
View at: Google Scholar
S. Dhinagar and B. Nagalingam, “Experimental investigation on non-edible vegetable oil operation in a LHR diesel engine for improved performance,” SAE 932846, 1993.
View at: Google Scholar
M. M. Azam, A. Waris, and N. M. Nahar, “Prospects and potential of fatty acid methyl esters of some non-traditional seed oils for use as biodiesel in India,” Biomass and Bioenergy, vol. 29, no. 4, pp. 293–302, 2005.
View at: Publisher Site | Google Scholar
B. K. De and D. K. Bhattacharyya, “Biodiesel from minor vegetable oils like karanja oil and nahor oil,” Lipid/Fett, vol. 101, no. 10, pp. 404–406, 1999.
View at: Publisher Site | Google Scholar
S. K. Karmee and A. Chadha, “Preparation of biodiesel from crude oil of Pongamia pinnata,” Bioresource Technology, vol. 96, no. 13, pp. 1425–1429, 2005.
View at: Publisher Site | Google Scholar
Y. C. Sharma and B. Singh, “Development of biodiesel from karanja, a tree found in rural India,” Fuel, vol. 87, no. 8-9, pp. 1740–1742, 2008.
View at: Publisher Site | Google Scholar
M. Naik, L. C. Meher, S. N. Naik, and L. M. Das, “Production of biodiesel from high free fatty acid Karanja (Pongamia pinnata) oil,” Biomass and Bioenergy, vol. 32, no. 4, pp. 354–357, 2008.
View at: Publisher Site | Google Scholar
P. T. Scott, L. Pregelj, N. Chen, J. S. Hadler, M. A. Djordjevic, and P. M. Gresshoff, “Pongamia pinnata: an untapped resource for the biofuels industry of the future,” BioEnergy Research, vol. 1, no. 1, pp. 2–11, 2008.
View at: Google Scholar
M. N. Nabi, S. M. N. Hoque, and M. S. Akhter, “Karanja (Pongamia Pinnata) biodiesel production in Bangladesh, characterization of karanja biodiesel and its effect on diesel emissions,” Fuel Processing Technology, vol. 90, no. 9, pp. 1080–1086, 2009.
View at: Publisher Site | Google Scholar
S. Khandelwal and R. Y. Chauhan, “Life cycle assessment of Neem and Karanja biodiesel: an overview,” International Journal of ChemTech Research, vol. 5, no. 2, pp. 659–665, 2013.
View at: Google Scholar
S. R. Kalbande, S. N. Pawar, and S. B. Jadhav, “Production of Karanja biodiesel and its utilization in diesel engine generator set for power generation,” Karnataka Journal of Agricultural Sciences, vol. 20, no. 3, pp. 680–683, 2007.
View at: Google Scholar
http://en.wikipedia.org/wiki/Geography_of_Bangladesh.
M. N. Nabi, S. M. N. Hoque, and M. S. Uddin, “Prospect of Jatropha curcas and pithraj cultivation in Bangladesh,” Journal of Engineering and Technology, vol. 7, no. 1, pp. 41–54, 2009.
View at: Google Scholar
J. A. Duke, “Pongamia pinnata (L) Pierre,” 2013, http://www.hort.purdue.edu/newcrop/duke_energy/Pongamia_pinnata.html.
View at: Google Scholar
Heather Richman, “Asia Pacific Clean Energy Summit,” 2012, http://www.ct-si.org/events/APCE2012/sld/pdf/30.pdf.
View at: Google Scholar
S. S. Karhale, R. G. Nadre, D. K. Das, and S. K. Dash, “Studies on comparative performance of a compression ignition engine with different blends of biodiesel and diesel under varying operating conditions,” Karnataka Journal of Agricultural Science, vol. 21, pp. 246–249, 2008.
View at: Google Scholar
L. G. Schumacher, S. C. Borgelt, D. Fosseen, W. Goetz, and W. G. Hires, “Heavy-duty engine exhaust emission tests using methyl ester soybean oil/diesel fuel blends,” Bioresource Technology, vol. 57, no. 1, pp. 31–36, 1996.
View at: Publisher Site | Google Scholar
H. Aydin and H. Bayindir, “Performance and emission analysis of cottonseed oil methyl ester in a diesel engine,” Renewable Energy, vol. 35, no. 3, pp. 588–592, 2010.
View at: Publisher Site | Google Scholar
H. Hazar, “Effects of biodiesel on a low heat loss diesel engine,” Renewable Energy, vol. 34, no. 6, pp. 1533–1540, 2009.
View at: Publisher Site | Google Scholar
A. N. Ozsezen, M. Canakci, A. Turkcan, and C. Sayin, “Performance and combustion characteristics of a DI diesel engine fueled with waste palm oil and canola oil methyl esters,” Fuel, vol. 88, no. 4, pp. 629–636, 2009.
View at: Publisher Site | Google Scholar
Z. Utlu and M. S. Koçak, “The effect of biodiesel fuel obtained from waste frying oil on direct injection diesel engine performance and exhaust emissions,” Renewable Energy, vol. 33, no. 8, pp. 1936–1941, 2008.
View at: Publisher Site | Google Scholar
H. Özgünay, S. Çolak, G. Zengin, Ö. Sari, H. Sarikahya, and L. Yüceer, “Performance and emission study of biodiesel from leather industry pre-fleshings,” Waste Management, vol. 27, no. 12, pp. 1897–1901, 2007.
View at: Publisher Site | Google Scholar
H. Raheman and A. G. Phadatare, “Diesel engine emissions and performance from blends of karanja methyl ester and diesel,” Biomass & Bioenergy, vol. 27, no. 4, pp. 393–397, 2004.
View at: Publisher Site | Google Scholar
Y. Ulusoy, Y. Tekin, M. Četinkaya, and F. Karaosmanoǧlu, “The engine tests of biodiesel from used frying oil,” Energy Sources, Part A: Recovery, Utilization, and Environmental Effects, vol. 26, no. 10, pp. 927–932, 2004.
View at: Publisher Site | Google Scholar
E. Buyukkaya, “Effects of biodiesel on a DI diesel engine performance, emission and combustion characteristics,” Fuel, vol. 89, no. 10, pp. 3099–3105, 2010.
View at: Publisher Site | Google Scholar
S. H. Choi and Y. Oh, “The emission effects by the use of biodiesel fuel,” International Journal of Modern Physics B, vol. 20, no. 25-27, pp. 4481–4487, 2006.
View at: Publisher Site | Google Scholar
M. Karabektas, “The effects of turbocharger on the performance and exhaust emissions of a diesel engine fuelled with biodiesel,” Renewable Energy, vol. 34, no. 4, pp. 989–993, 2009.
View at: Publisher Site | Google Scholar
S. Murillo, J. L. Míguez, J. Porteiro, E. Granada, and J. C. Morán, “Performance and exhaust emissions in the use of biodiesel in outboard diesel engines,” Fuel, vol. 86, no. 12-13, pp. 1765–1771, 2007.
View at: Publisher Site | Google Scholar
A. C. Hansen, M. R. Gratton, and W. Yuan, “Diesel engine performance and NOx emissions from oxygenated biofuels and blends with diesel fuel,” Transactions of the ASABE, vol. 49, no. 3, pp. 589–595, 2006.
View at: Publisher Site | Google Scholar
C. Carraretto, A. Macor, A. Mirandola, A. Stoppato, and S. Tonon, “Biodiesel as alternative fuel: experimental analysis and energetic evaluations,” Energy, vol. 29, no. 12–15, pp. 2195–2211, 2004.
View at: Publisher Site | Google Scholar
C. Kaplan, R. Arslan, and A. Sürmen, “Performance characteristics of sunflower methyl esters as biodiesel,” Energy Sources A: Recovery, Utilization and Environmental Effects, vol. 28, no. 8, pp. 751–755, 2006.
View at: Publisher Site | Google Scholar
J. F. Reyes and M. A. Sepulveda, “PM-10 emissions and power of a diesel engine fueled with crude and refined Biodiesel from salmon oil,” Fuel, vol. 85, no. 12-13, pp. 1714–1723, 2006.
View at: Publisher Site | Google Scholar
M. Çetinkaya, Y. Ulusoy, Y. Tekìn, and F. Karaosmanoǧlu, “Engine and winter road test performances of used cooking oil originated biodiesel,” Energy Conversion and Management, vol. 46, no. 7-8, pp. 1279–1291, 2005.
View at: Publisher Site | Google Scholar
Y.-C. Lin, W.-J. Lee, T.-S. Wu, and C.-T. Wang, “Comparison of PAH and regulated harmful matter emissions from biodiesel blends and paraffinic fuel blends on engine accumulated mileage test,” Fuel, vol. 85, no. 17-18, pp. 2516–2523, 2006.
View at: Publisher Site | Google Scholar
F. Neto da Silva, A. S. Prata, and J. R. Teixeira, “Technical feasibility assessment of oleic sunflower methyl ester utilisation in Diesel bus engines,” Energy Conversion and Management, vol. 44, no. 18, pp. 2857–2878, 2003.
View at: Publisher Site | Google Scholar
H. S. Yücesu and C. Ilkiliç, “Effect of cotton seed oil methyl ester on the performance and exhaust emission of a diesel engine,” Energy Sources A: Recovery, Utilization and Environmental Effects, vol. 28, no. 4, pp. 389–398, 2006.
View at: Publisher Site | Google Scholar
B.-F. Lin, J.-H. Huang, and D.-Y. Huang, “Experimental study of the effects of vegetable oil methyl ester on DI diesel engine performance characteristics and pollutant emissions,” Fuel, vol. 88, no. 9, pp. 1779–1785, 2009.
View at: Publisher Site | Google Scholar
D. H. Qi, L. M. Geng, H. Chen, Y. Z. Bian, J. Liu, and X. C. Ren, “Combustion and performance evaluation of a diesel engine fueled with biodiesel produced from soybean crude oil,” Renewable Energy, vol. 34, no. 12, pp. 2706–2713, 2009.
View at: Publisher Site | Google Scholar
M. Lapuerta, J. M. Herreros, L. L. Lyons, R. García-Contreras, and Y. Briceño, “Effect of the alcohol type used in the production of waste cooking oil biodiesel on diesel performance and emissions,” Fuel, vol. 87, no. 15-16, pp. 3161–3169, 2008.
View at: Publisher Site | Google Scholar
A. Keskin, M. Gürü, and D. Altiparmak, “Influence of tall oil biodiesel with Mg and Mo based fuel additives on diesel engine performance and emission,” Bioresource Technology, vol. 99, no. 14, pp. 6434–6442, 2008.
View at: Publisher Site | Google Scholar
B. Ghobadian, H. Rahimi, A. M. Nikbakht, G. Najafi, and T. F. Yusaf, “Diesel engine performance and exhaust emission analysis using waste cooking biodiesel fuel with an artificial neural network,” Renewable Energy, vol. 34, no. 4, pp. 976–982, 2009.
View at: Publisher Site | Google Scholar
J.-T. Song and C.-H. Zhang, “An experimental study on the performance and exhaust emissions of a diesel engine fuelled with soybean oil methyl ester,” Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering, vol. 222, no. 12, pp. 2487–2496, 2008.
View at: Publisher Site | Google Scholar
M. I. Al-Widyan, G. Tashtoush, and M. Abu-Qudais, “Utilization of ethyl ester of waste vegetable oils as fuel in diesel engines,” Fuel Processing Technology, vol. 76, no. 2, pp. 91–103, 2002.
View at: Publisher Site | Google Scholar
N. Shrivastava, S. N. Varma, and M. Pandey, “Experimental study on the production of Karanja oil methyl ester and its effect on diesel engine,” International Journal of Renewable Energy Development, vol. 1, no. 3, pp. 115–122, 2012.
View at: Google Scholar
H. Dharmadhikari, P. R. Kumar, and S. S. Rao, “Performance and emissions of CI engine using blends of biodiesel and diesel at different injection pressures,” International Journal of Applied Research in Mechanical Engineering, vol. 2, no. 2, pp. 1–6, 2012.
View at: Google Scholar
Y. Singh, A. Singla, and N. Lohani, “Production of biodiesel from oils of Jatropha, Karanja and performance analysis on CI engine,” International Journal of Innovative Research and Development, vol. 2, no. 3, pp. 286–294, 2013.
View at: Google Scholar
M. V. Nagarhalli, V. M. Nandedkar, and K. C. Mohite, “Emission and performance characteristics of karanja biodiesel and its blends in a CI engine and its economics,” ARPN Journal of Engineering and Applied Sciences, vol. 5, no. 2, pp. 52–56, 2010.
View at: Google Scholar
N. Panigrahi, M. K. Mohanty, and A. K. Pradhan, “Non-edible Karanja biodiesel—a sustainable fuel for C.I. engine,” International Journal of Engineering Research and Applications, vol. 2, no. 6, pp. 853–860, 2012.
View at: Google Scholar
P. K. Sahoo, L. M. Das, M. K. G. Babu, and S. N. Naik, “Biodiesel development from high acid value polanga seed oil and performance evaluation in a CI engine,” Fuel, vol. 86, no. 3, pp. 448–454, 2007.
View at: Publisher Site | Google Scholar
C.-Y. Lin and H.-A. Lin, “Engine performance and emission characteristics of a three-phase emulsion of biodiesel produced by peroxidation,” Fuel Processing Technology, vol. 88, no. 1, pp. 35–41, 2007.
View at: Publisher Site | Google Scholar
A. S. Ramadhas, C. Muraleedharan, and S. Jayaraj, “Performance and emission evaluation of a diesel engine fueled with methyl esters of rubber seed oil,” Renewable Energy, vol. 30, no. 12, pp. 1789–1800, 2005.
View at: Publisher Site | Google Scholar
M. Canakci, “Performance and emissions characteristics of biodiesel from soybean oil,” Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering, vol. 219, no. 7, pp. 915–922, 2005.
View at: Publisher Site | Google Scholar
G. Fontaras, G. Karavalakis, M. Kousoulidou et al., “Effects of biodiesel on passenger car fuel consumption, regulated and non-regulated pollutant emissions over legislated and real-world driving cycles,” Fuel, vol. 88, no. 9, pp. 1608–1617, 2009.
View at: Publisher Site | Google Scholar
S. Puhan, N. Vedaraman, G. Sankaranarayanan, and B. V. B. Ram, “Performance and emission study of Mahua oil (madhuca indica oil) ethyl ester in a 4-stroke natural aspirated direct injection diesel engine,” Renewable Energy, vol. 30, no. 8, pp. 1269–1278, 2005.
View at: Publisher Site | Google Scholar
G. Labeckas and S. Slavinskas, “The effect of rapeseed oil methyl ester on direct injection Diesel engine performance and exhaust emissions,” Energy Conversion and Management, vol. 47, no. 13-14, pp. 1954–1967, 2006.
View at: Publisher Site | Google Scholar
2013, http://www.himalayaninstitute.org/humanitarian/tibetan-settlements/about-pongamia/.
O. Armas, K. Yehliu, and A. L. Boehman, “Effect of alternative fuels on exhaust emissions during diesel engine operation with matched combustion phasing,” Fuel, vol. 89, no. 2, pp. 438–456, 2010.
View at: Publisher Site | Google Scholar
H. Kim and B. Choi, “The effect of biodiesel and bioethanol blended diesel fuel on nanoparticles and exhaust emissions from CRDI diesel engine,” Renewable Energy, vol. 35, no. 1, pp. 157–163, 2010.
View at: Publisher Site | Google Scholar
X. Meng, G. Chen, and Y. Wang, “Biodiesel production from waste cooking oil via alkali catalyst and its engine test,” Fuel Processing Technology, vol. 89, no. 9, pp. 851–857, 2008.
View at: Publisher Site | Google Scholar
A. Hull, I. Golubkov, B. Kronberg, and J. Van Stam, “Alternative fuel for a standard diesel engine,” International Journal of Engine Research, vol. 7, no. 1, pp. 51–63, 2006.
View at: Publisher Site | Google Scholar
M. Gumus and S. Kasifoglu, “Performance and emission evaluation of a compression ignition engine using a biodiesel (apricot seed kernel oil methyl ester) and its blends with diesel fuel,” Biomass and Bioenergy, vol. 34, no. 1, pp. 134–139, 2010.
View at: Publisher Site | Google Scholar
D. Sharma, S. L. Soni, and J. Mathur, “Emission reduction in a direct injection diesel engine fueled by neem-diesel blend,” Energy Sources A: Recovery, Utilization and Environmental Effects, vol. 31, no. 6, pp. 500–508, 2009.
View at: Publisher Site | Google Scholar
M. Gürü, A. Koca, Ö. Can, C. Çinar, and F. Şahin, “Biodiesel production from waste chicken fat based sources and evaluation with Mg based additive in a diesel engine,” Renewable Energy, vol. 35, no. 3, pp. 637–643, 2010.
View at: Publisher Site | Google Scholar
J. M. Luján, V. Bermúdez, B. Tormos, and B. Pla, “Comparative analysis of a DI diesel engine fuelled with biodiesel blends during the European MVEG-A cycle: performance and emissions (II),” Biomass and Bioenergy, vol. 33, no. 6-7, pp. 948–956, 2009.
View at: Publisher Site | Google Scholar
M. A. Kalam and H. H. Masjuki, “Testing palm biodiesel and NPAA additives to control NOx and CO while improving efficiency in diesel engines,” Biomass and Bioenergy, vol. 32, no. 12, pp. 1116–1122, 2008.
View at: Publisher Site | Google Scholar
S. Godiganur, C. Suryanarayana Murthy, and R. P. Reddy, “Performance and emission characteristics of a Kirloskar HA394 diesel engine operated on fish oil methyl esters,” Renewable Energy, vol. 35, no. 2, pp. 355–359, 2010.
View at: Publisher Site | Google Scholar
S. Godiganur, C. H. S. Murthy, and R. P. Reddy, “6BTA 5.9 G2-1 cummins engine performance and emission tests using methyl ester mahua (Madhuca indica) oil/diesel blends,” Renewable Energy, vol. 34, no. 10, pp. 2172–2177, 2009.
View at: Publisher Site | Google Scholar
S. J. Deshmukh and L. B. Bhuyar, “Transesterified Hingan (Balanites) oil as a fuel for compression ignition engines,” Biomass and Bioenergy, vol. 33, no. 1, pp. 108–112, 2009.
View at: Publisher Site | Google Scholar
D. M. Korres, D. Karonis, E. Lois, M. B. Linck, and A. K. Gupta, “Aviation fuel JP-5 and biodiesel on a diesel engine,” Fuel, vol. 87, no. 1, pp. 70–78, 2008.
View at: Publisher Site | Google Scholar
N. Usta, “Use of tobacco seed oil methyl ester in a turbocharged indirect injection diesel engine,” Biomass and Bioenergy, vol. 28, no. 1, pp. 77–86, 2005.
View at: Publisher Site | Google Scholar
M. S. Kumar, A. Ramesh, and B. Nagalingam, “A comparison of the different methods of using jatropha oil as fuel in a compression ignition engine,” Journal of Engineering for Gas Turbines and Power, vol. 132, no. 3, Article ID 032801, pp. 32801–32811, 2010.
View at: Publisher Site | Google Scholar
N. R. Banapurmath, P. G. Tewari, and R. S. Hosmath, “Performance and emission characteristics of a DI compression ignition engine operated on Honge, Jatropha and sesame oil methyl esters,” Renewable Energy, vol. 33, no. 9, pp. 1982–1988, 2008.
View at: Publisher Site | Google Scholar
N. R. Banapurmath and P. G. Tewari, “Performance of a low heat rejection engine fuelled with low volatile Honge oil and its methyl ester (HOME),” Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy, vol. 222, no. 3, pp. 323–330, 2008.
View at: Publisher Site | Google Scholar
P. K. Sahoo, L. M. Das, M. K. G. Babu et al., “Comparative evaluation of performance and emission characteristics of jatropha, karanja and polanga based biodiesel as fuel in a tractor engine,” Fuel, vol. 88, no. 9, pp. 1698–1707, 2009.
View at: Publisher Site | Google Scholar
M. A. R. Nascimento, E. S. Lora, P. S. P. Correa et al., “Biodiesel fuel in diesel micro-turbine engines: modelling and experimental evaluation,” Energy, vol. 33, no. 2, pp. 233–240, 2008.
View at: Publisher Site | Google Scholar
A. Pal, A. Verma, S. S. Kachhwaha, and S. Maji, “Biodiesel production through hydrodynamic cavitation and performance testing,” Renewable Energy, vol. 35, no. 3, pp. 619–624, 2010.
View at: Publisher Site | Google Scholar
L. Zhu, W. Zhang, W. Liu, and Z. Huang, “Experimental study on particulate and NOx emissions of a diesel engine fueled with ultra low sulfur diesel, RME-diesel blends and PME-diesel blends,” Science of the Total Environment, vol. 408, no. 5, pp. 1050–1058, 2010.
View at: Publisher Site | Google Scholar
K. Ryu, “The characteristics of performance and exhaust emissions of a diesel engine using a biodiesel with antioxidants,” Bioresource Technology, vol. 101, no. 1, pp. S78–S82, 2010.
View at: Publisher Site | Google Scholar
D. Agarwal, S. Sinha, and A. K. Agarwal, “Experimental investigation of control of NO_x emissions in biodiesel-fueled compression ignition engine,” Renewable Energy, vol. 31, no. 14, pp. 2356–2369, 2006.
View at: Publisher Site | Google Scholar
S. Puhan, N. Vedaraman, B. V. B. Ram, G. Sankarnarayanan, and K. Jeychandran, “Mahua oil (Madhuca Indica seed oil) methyl ester as biodiesel-preparation and emission characterstics,” Biomass and Bioenergy, vol. 28, no. 1, pp. 87–93, 2005.
View at: Publisher Site | Google Scholar
L. Turrio-Baldassarri, C. L. Battistelli, L. Conti et al., “Emission comparison of urban bus engine fueled with diesel oil and “biodiesel” blend,” Science of the Total Environment, vol. 327, no. 1–3, pp. 147–162, 2004.
View at: Publisher Site | Google Scholar
D. H. Qi, H. Chen, L. M. Geng, and Y. Z. Bian, “Experimental studies on the combustion characteristics and performance of a direct injection engine fueled with biodiesel/diesel blends,” Energy Conversion and Management, vol. 51, no. 12, pp. 2985–2992, 2010.
View at: Publisher Site | Google Scholar
C. S. Cheung, L. Zhu, and Z. Huang, “Regulated and unregulated emissions from a diesel engine fueled with biodiesel and biodiesel blended with methanol,” Atmospheric Environment, vol. 43, no. 32, pp. 4865–4872, 2009.
View at: Publisher Site | Google Scholar
A. Tsolakis, A. Megaritis, M. L. Wyszynski, and K. Theinnoi, “Engine performance and emissions of a diesel engine operating on diesel-RME (rapeseed methyl ester) blends with EGR (exhaust gas recirculation),” Energy, vol. 32, no. 11, pp. 2072–2080, 2007.
View at: Publisher Site | Google Scholar
N. Usta, “An experimental study on performance and exhaust emissions of a diesel engine fuelled with tobacco seed oil methyl ester,” Energy Conversion and Management, vol. 46, no. 15-16, pp. 2373–2386, 2005.
View at: Publisher Site | Google Scholar
N. Usta, E. Öztürk, Ö. Can et al., “Combustion of bioDiesel fuel produced from hazelnut soapstock/waste sunflower oil mixture in a Diesel engine,” Energy Conversion and Management, vol. 46, no. 5, pp. 741–755, 2005.
View at: Publisher Site | Google Scholar
N. R. Banapurmath, P. G. Tewari, and R. S. Hosmath, “Effect of biodiesel derived from Honge oil and its blends with diesel when directly injected at different injection pressures and injection timings in single-cylinder water-cooled compression ignition engine,” Proceedings of the Institution of Mechanical Engineers Part A: Journal of Power and Energy, vol. 223, pp. 31–40, 2009.
View at: Google Scholar
M. P. Dorado, E. Ballesteros, J. M. Arnal, J. Gómez, and F. J. López, “Exhaust emissions from a diesel engine fueled with transesterified waste olive oil,” Fuel, vol. 82, no. 11, pp. 1311–1316, 2003.
View at: Publisher Site | Google Scholar
B. Baiju, M. K. Naik, and L. M. Das, “A comparative evaluation of compression ignition engine characteristics using methyl and ethyl esters of Karanja oil,” Renewable Energy, vol. 34, no. 6, pp. 1616–1621, 2009.
View at: Publisher Site | Google Scholar
S. Kalligeros, F. Zannikos, S. Stournas et al., “An investigation of using biodiesel/marine diesel blends on the performance of a stationary diesel engine,” Biomass and Bioenergy, vol. 24, no. 2, pp. 141–149, 2003.
View at: Publisher Site | Google Scholar
M. Lapuerta, O. Armas, R. Ballesteros, and J. Fernández, “Diesel emissions from biofuels derived from Spanish potential vegetable oils,” Fuel, vol. 84, no. 6, pp. 773–780, 2005.
View at: Publisher Site | Google Scholar
K. Dincer, “Lower emissions from biodiesel combustion,” Energy Sources Part A: Recovery, Utilization and Environmental Effects, vol. 30, no. 10, pp. 963–968, 2008.
View at: Publisher Site | Google Scholar
R. Ballesteros, J. J. Hernández, L. L. Lyons, B. Cabañas, and A. Tapia, “Speciation of the semivolatile hydrocarbon engine emissions from sunflower biodiesel,” Fuel, vol. 87, no. 10-11, pp. 1835–1843, 2008.
View at: Publisher Site | Google Scholar
P. Mahanta, S. Mishra, and Y. Kushwah, “A comparative study of pongamia pinnata and jatropha curcus oil as diesel substitute,” International Energy Journal, vol. 7, no. 1, pp. 1–12, 2006.
View at: Google Scholar
M. S. Uddin, M. U. H. Joardder, and M. N. Islam, “Design and construction of fixed bed pyrolysis system and plum seed pyrolysis for bio-oil production,” International Journal of Advanced Renewable Energy Research, vol. 7, no. 1, pp. 405–409, 2012.
View at: Google Scholar
M. Kader, M. U. H. Joardder, M. R. Islam, B. K. Das, and M. M. Hasan, “Production of liquid fuel and activated carbon from mahogany seed by using pyrolysis technology,” in Proceedings of the International Conference on Mechanical Engineering (ICME '11), Bangladesh University of Engineering and Technology, Dhaka, Bangladesh, December 2011.
View at: Google Scholar
M. U. H. Joardder, M. R. Islam, and M. R. A. Beg, “Pyrolysis of coconut shell for bio-oil,” in Proceedings of the International Conference on Mechanical Engineering (ICME '11), Bangladesh University of Engineering and Technology, Dhaka, Bangladesh, December 2011.
View at: Google Scholar
K. Annamalai and I. K. Puri, Combustion Science and Engineering, CRC Press, New York, NY, USA, 2006.
AGF Seeds, 2013, /http://www.agfseeds.com/pongamia.
R. G. Andrews and P. C. Patniak, “Feasibility of utilizing a biomass derived fuel for industrial gas turbine applications,” in Bio-Oil Production & Utilization, A. V. Bridgwater and E. N. Hogan, Eds., pp. 236–245, CPL Press, Berkshire, UK, 1996.
View at: Google Scholar
F. Rick and U. Vix, “Product standards for pyrolysis products for use as fuel in industrial firing plants,” in Biomass Pyrolysis Liquids Upgrading and Utilization, A. V. Bridgwater and G. Grassi, Eds., Elsevier, London, UK, 1991.
View at: Google Scholar
Subbarao, Gasification of De-Oiled Cakes of Jatropha and Pongamia Seeds, 2010.
J. A. Neto, R. S. Cruz, J. M. Alves, M. Pires, S. Robra, and E. Parente Jr., “Energy balance of ester methyl and ethyl of castor oil plant oil,” in Proceedings of the Brazilian Congress of Castor Oil Plant, Campina Grande, Brazil, 2004.
View at: Google Scholar
“Carbon emissions from burning biomass for energy,” http://www.pfpi.net/wp-content/uploads/2011/04/PFPI-biomass-carbon-accounting-overview_April.pdf.
View at: Google Scholar
T. Thamsiriroj and J. D. Murphy, “Is it better to import palm oil from Thailand to produce biodiesel in Ireland than to produce biodiesel from indigenous Irish rape seed?” Applied Energy, vol. 86, no. 5, pp. 595–604, 2009.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2014 P. K. Halder et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

10390

Downloads

3282

Citations