Research on an Improved Method for Permanent Magnet Synchronous Motor

Liu, Yingpei; Gao, Tao; Li, Guo

doi:https://doi.org/10.1155/2014/816421

Journal of Sensors

On this page

Abstract Introduction Conclusion References Copyright Related Articles

Special Issue

Wireless Smart Sensor Networks, System, Trends, and the Applications in Engineering

View this Special Issue

Research Article | Open Access

Volume 2014 | Article ID 816421 | https://doi.org/10.1155/2014/816421

Research on an Improved Method for Permanent Magnet Synchronous Motor

Yingpei Liu,¹Tao Gao,²and Guo Li³

Academic Editor: Tinggui Chen

Received20 Jun 2014

Revised19 Jul 2014

Accepted14 Aug 2014

Published01 Sept 2014

Abstract

In permanent magnet synchronous motor (PMSM) traditional vector control system, PI regulator is used in the speed loop, but it has some defects. An improved method of PMSM vector control is proposed in the paper. The active-disturbance rejection control (ADRC) speed regulator is designed with the input signals of given speed and real speed and the output of given stator current q coordinate component. Then, in order to optimize ADRC controller, the least squares support vector machines (LSSVM) optimal regression model is derived and successfully embedded in the ADRC controller. ADRC observation precision and dynamic response of the system are improved. The load disturbance effect on the system is reduced to a large extent. The system anti-interference ability is further improved. Finally, the current sensor CSNE151-100 is selected to sample PMSM stator currents. The voltage sensor JLBV1 is used to sample the stator voltage. The rotor speed of PMSM is measured by mechanical speed sensor, the type of which is BENTLY 330500. Experimental platform is constructed to verify the effectiveness of the proposed method.

1. Introduction

With the advantages of high power density and high efficiency, permanent magnet synchronous motor (PMSM) is widely used in a variety of high performance electric drive fields. PMSM control method has been widely concerned and researched [1–17].

PMSM is nonlinear and is strongly coupling. In order to achieve high performance operation, the uncertainties and nonlinear impact on the system must be overcome. In traditional vector control system, PI regulator is adopted in the speed loop. PI controller structure is simple; nevertheless, its parameter robustness is poor and there are contradictions between speed and overshoot. PI control is difficult to meet the requirements of high performance operation.

Based on the preliminary research results, an improved method of PMSM control is proposed in the paper. The active-disturbance rejection controller (ADRC) is designed for speed loop. Then, in order to optimize ADRC controller, the least squares support vector machines (LSSVM) optimal regression model is derived and successfully embedded in the ADRC controller. ADRC observation precision and dynamic response of the system are improved. The load disturbances effect on the system is reduced to a large extent. The system anti-interference ability is further improved. Finally, different sensors sampling current, voltage, and rotor speed are used to finish experimental validation.

2. PMSM Mathematical Model

coordinate is chosen. The voltage equation of PMSM is as follows: where are stator voltage coordinate components; are stator current coordinate components; is stator resistance, are stator inductance; is rotor speed; is permanent magnet flux linkage; and is differential operator.

The electromagnetic torque equation of PMSM is shown as follows:

For surface PMSM, . Equation (3) can be derived from (2):

The motion equation of PMSM is as follows: where is rotational inertia; is friction coefficient; and is the load.

3. Design of ADRC Speed Regulator

3.1. ADRC Theory

ADRC controller is composed of tracking-differentiator (TD) and extended state observer (ESO) and nonlinear state error feedback control rate (NLSEF) [18, 19].

First-order system is assumed as follows: The TD model of the first-order system (5) is as follows: where is defined as where is the tracking signal of ; is the tracking speed factor; and is the sample period.

The ESO model of first-order system (3) is as follows: where is the tracking signal of ; is the estimation value of disturbance; , are nonlinear factors; is filter factor; , are the parameters; and is nonlinear function:

NLSEF model of system (3) is as follows: where is filter factor and is nonlinear factor.

3.2. Speed Regulator Design

Equation (11) is obtained from (3) and (4):

Based on ADRC theory, , , and are seen as disturbance velocity loop. The disturbance is denoted as , . Equation (12) is got as follows: The output of the speed loop is the given value of , which is . Then, (13) is got:

Speed regulator based on ADRC with and as the input signals and as the output signal is designed according to (6), (8), and (10). The diagram of speed regulator based on ADRC is shown in Figure 1.

4. Design of LSSVM-ADRC Controller

4.1. LSSVM Theory

Assume training sample data , while is the input data and is the output data. The goal of LSSVM is to construct a regression model as follows [20–23]: where is weight vector; is the offset; and is the mapping function in kernel space.

LSSVM regression algorithm is to calculate the optimum as follows: where is the optimized objective function; is the regularization parameter; and is the relaxation factor of insensitive loss function.

The corresponding Lagrange function is shown as follows: where is Lagrange factor.

The partial derivation operation of is made, and then make it to zero. Equation (17) is got:

Thus, the optimization problem is transformed into solving the following linear equation: where ; is an unit matrix; ; ; and , , .

is a kernel function. The approximation accuracy and computational efficiency are both considered in the paper; Gaussian RBF kernel function is chosen and shown as follows: where is a coefficient which decides the scaling extent of input variable in learning algorithm.

Define . The solution of (18) is expressed as follows:

Therefore, the LSSVM approximation function is as follows:

4.2. LSSVM-ADRC Controller

In Figure 1, sample the output variables of ESO. Train LSSVM model to get the optimal regression model with as the input signal and as the output signal. Then, embed the LSSVM optimal regression model into the ADRC controller. The diagram of LSSVM-ADRC is shown in Figure 2.

In Figure 2, the LSSVM model can estimate part of system disturbance according to the input signal . and the other disturbance estimated by ESO compose the total disturbance. Therefore, it can be seen that the ADRC disturbances estimation burden has reduced and system response has been improved. Furthermore, the system anti-interference ability is enhanced. The mathematical model of LSSVM-ADRC controller is obtained:

5. Simulation and Experiment Results

5.1. Simulation Result

Based on Matlab/Simulink, the system simulation model is constructed to carry out simulation. LSSVM training is programed using m file in Matlab. The main parameters of PMSM are as follows: , , and .(1)The given speed is 700 r/min; at 0.3 s load torque changes from 0 to 3 N·m. The speed waves are shown in Figures 3 and 4 under ADRC speed regulator and LSSVM-ADRC speed regulator, respectively.

(a) Speed wave

(b) Part of speed wave when load changes front and back

(a) Speed wave

(b) Part of speed wave when load changes front and back

From Figure 3, it can be seen that, based on ADRC speed controller, rotor speed instantly drops to 660 r/min when load suddenly changes, and then it reaches a steady state once again after 0.1 seconds. Contrastively, under LSSVM-ADRC speed controller in Figure 4, rotor speed drops to 695 r/min when load suddenly changes, and only after 0.06 s it reaches steady state again. The reason is LSSVM has reduced the burden on the ESO observation. The observation accuracy and system response speed have been improved under LSSVM-ADRC method.(2)The given speed is 1500 r/min; at 0.25 s load torque changes from 3 N·m to 6 N·m. The speed waves are shown in Figures 5 and 6 under ADRC speed regulator and LSSVM-ADRC speed regulator, respectively.

(a) Speed wave

(b) Part of speed wave when load changes front and back

(a) Speed wave

(b) Part of speed wave when load changes front and back

From Figure 5, it can be seen that, based on ADRC speed controller, when load suddenly changes rotor speed drops from 1500 r/min to 1470 r/min, and after that it reaches a steady state after 0.07 seconds. Contrastively, under LSSVM-ADRC speed controller in Figure 6, rotor speed drops from 1500 r/min to 1497 r/min when load suddenly changes, and only after 0.03 s it reaches a steady state again.

Combining the above simulation results under conditions of low speed and high speed, it can be concluded that, based on LSSVM-ADRC method, system responsiveness has been greatly improved; at the same time, system anti-interference ability has been improved to a large extent.

5.2. Experiment Result

To validate the performance of the proposed method, experimental study is conducted on a PMSM turbine. The motor parameters are the same as the simulation motor. The chip TI DSP TMS320F2812 is chosen as the control core. The AC-DC-AC main circuit structure is adopted. The rectifier module uses diode and inverter module uses MOSFET. The current sensor CSNE151-100 is selected to sample PMSM stator currents. The voltage sensor JLBV1 is used to sample the stator voltage. The rotor speed of PMSM is measured by mechanical speed sensor, the type of which is BENTLY 330500.

The given speed is 700 r/min and load torque changes from 0 to 3 N·m. The rotor speed waves are shown in Figures 7 and 8 under ADRC speed regulator and LSSVM-ADRC speed regulator, respectively.

(a) Speed wave

(b) Electromagnet torque wave

The given speed is 1500 r/min and load torque changes from 3 N·m to 6 N·m. The speed waves are shown in Figures 9 and 10 under ADRC speed regulator and LSSVM-ADRC speed regulator, respectively.

(a) Speed wave

(b) Electromagnet torque wave

From Figures 7–10, it can be seen that, based on LSSVM-ADRC method, system responsiveness has been greatly improved; at the same time, system anti-interference ability has been improved to a large extent. It is consistent with the simulation results.

6. Conclusion

An improved method of PMSM vector control is proposed in the paper. The ADRC speed regulator is designed. Then, LSSVM optimal regression model is derived and embedded in the ADRC controller. ADRC observation precision and dynamic response of the system are improved. The system anti-interference ability is further improved. Finally, the current sensor, voltage sensor, and speed sensor are chosen to sample PMSM current, voltage, and speed. Experimental platform is constructed to verify the effectiveness of the proposed method.

Conflict of Interests

The authors declare that there is no conflict of interests regarding the publication of this paper.

Acknowledgment

This paper is supported by the Fundamental Research Funds for the Central Universities (2014MS89) and (2014QN46).

References

H. Zhu, X. Xiao, and Y.-D. Li, “Stator flux control scheme for permanent magnet synchronous motor torque predictive control,” Proceedings of the Chinese Society of Electrical Engineering, vol. 30, no. 21, pp. 86–90, 2010.
View at: Google Scholar
J. Faiz and S. H. Mohseni-Zonoozi, “A novel technique for estimation and control of stator flux of a salient-pole PMSM in DTC method based on MTPF,” IEEE Transactions on Industrial Electronics, vol. 50, no. 2, pp. 262–271, 2003.
View at: Publisher Site | Google Scholar
M. Kazerooni, S. Hamidifar, and N. C. Kar, “Analytical modelling and parametric sensitivity analysis for the PMSM steady-state performance prediction,” IET Electric Power Applications, vol. 7, no. 7, pp. 586–596, 2013.
View at: Publisher Site | Google Scholar
F. J. Lin, Y. C. Hung, and M. T. Tsai, “Fault-tolerant control for six-phase PMSM drive system via intelligent complementary sliding-mode control using TSKFNN-AMF,” IEEE Transactions on Industrial Electronics, vol. 60, no. 12, pp. 5747–5762, 2013.
View at: Publisher Site | Google Scholar
S. H. Li and H. Gu, “Fuzzy adaptive internal model control schemes for PMSM speed-regulation system,” IEEE Transactions on Industrial Informatics, vol. 8, no. 4, pp. 767–779, 2012.
View at: Publisher Site | Google Scholar
C. L. Xia, J. X. Zhao, Y. Yan, and T. N. Shi, “A novel direct torque control of matrix converter-fed PMSM drives using duty cycle control for torque ripple reduction,” IEEE Transaction on Industrial Electronics, vol. 61, no. 6, pp. 2700–2713, 2014.
View at: Publisher Site | Google Scholar
H. Liu and S. Li, “Speed control for PMSM servo system using predictive functional control and extended state observer,” IEEE Transactions on Industrial Electronics, vol. 59, no. 2, pp. 1171–1183, 2012.
View at: Publisher Site | Google Scholar
Z. Wang, Y. Zheng, Z. Zou, and M. Cheng, “Position sensorless control of interleaved CSI fed PMSM drive with extended Kalman filter,” IEEE Transactions on Magnetics, vol. 48, no. 11, pp. 3688–3691, 2012.
View at: Publisher Site | Google Scholar
Y. Da, X. Shi, and M. Krishnamurthy, “A novel universal sensor concept for survivable PMSM drives,” IEEE Transactions on Power Electronics, vol. 28, no. 12, pp. 5630–5638, 2013.
View at: Publisher Site | Google Scholar
B. Q. Li and H. Lin, “Direct control of current vector for surface-mounted permanent magnet synchronous motor,” Proceedings of the Chinese Society of Electrical Engineering, vol. 31, no. 1, pp. 288–294, 2011.
View at: Google Scholar
Y. Xu and Y. Zhong, “A novel direct torque control strategy of permanent magnet synchronous motors based on duty ratio control,” Transactions of China Electrotechnical Society, vol. 24, no. 10, pp. 27–32, 2009.
View at: Google Scholar
D. Sun, Y.-K. He, and Z.-Y. He, “Fault tolerant inverter based direct torque control for permanent magnet synchronous motor,” Journal of Zhejiang University (Engineering Science), vol. 41, no. 7, pp. 1101–1131, 2007.
View at: Google Scholar
S. He, A. R. Qiu, and X. M. Yuan, “Direct torque control of permanent magnet synchronous motor with SVM,” Micromotors, vol. 41, pp. 6–8, 2008.
View at: Google Scholar
L. Tang, L. Zhong, M. F. Rahman, and Y. Hu, “A novel direct torque controlled interior permanent magnet synchronous machine drive with low ripple in flux and torque and fixed switching frequency,” IEEE Transactions on Power Electronics, vol. 19, no. 2, pp. 346–354, 2004.
View at: Publisher Site | Google Scholar
J. Xu, Y. Xu, and J. Feng, “Direct torque control of permanent magnet synchronous machines based on modified integrator,” Transactions of China Electrotechnical Society, vol. 19, no. 7, pp. 77–80, 2004.
View at: Google Scholar
D. Sun and Y. K. He, “Space vector modulated based constant switching frequency direct control for permanent magnet synchronous motor,” Proceeding of the CSEE, vol. 25, pp. 112–116, 2005.
View at: Google Scholar
Y. P. Liu, “Space vector modulated direct torque control for PMSM based on ADRC,” Electric Power Automation Equipment, vol. 31, no. 11, pp. 78–82, 2011.
View at: Google Scholar
J. Q. Han, “From PID technique to active disturbance rejection control technique,” Control Engineering of China, vol. 9, pp. 13–18, 2002.
View at: Google Scholar
J. Q. Han, Active Disturbance Rejection Control Technique, National Defense Industry Press, Beijing, China, 2008.
C. Peng, G. Liu, and H. Sun, “Wind speed forecasting based on wavelet decomposition and differential evolution-support vector machine for wind farms,” Electric Power Automation Equipment, vol. 32, no. 1, pp. 9–13, 2012.
View at: Google Scholar
Y. Zhang, Least Squares Support Vector Machines Inverse Control of Two-Motor Variable Frequency Speed-Regulation Systems, Jiang Su University, 2011.
X. Shi, Z. Liu, M. Fu, and J. Wang, “Course control of air cushion vehicle based on SVM-ADRC,” Journal of Huazhong University of Science and Technology (Natural Science Edition), vol. 40, no. 5, pp. 59–63, 2012.
View at: Google Scholar
Z. C. Wu, Q. D. Ouyang, and Z. W. Hu, “Polarimetric SAR image classification using watershed-transformation and support vector machine,” Geomatics and Information Science of Wuhan University, vol. 37, no. 1, pp. 7–10, 2012.
View at: Google Scholar

Copyright

Copyright © 2014 Yingpei Liu et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

3029

Downloads

1456

Citations