Abstract

The deterioration of aero lubricating oil at high temperatures was accelerated by using a specific device simulating the operating conditions of engines, where the deterioration mechanism was obtained. Structures of the deteriorated lubricating oils were analyzed by gas chromatograph/mass spectrometer. From the results, it can be concluded that deterioration of aero lubricating oil at high temperatures was composed of thermal pyrolysis, oxidation, and polymerization, with the generation of a variety of products, such as alcohols, aldehydes, acids, and esters, which caused the deterioration of physicochemical properties of the aero lubricating oil.

1. Introduction

The change of molecular structure of aero lubricating oil is the fundamental cause that affects the functions of oil at high temperature [15]. The deterioration process, which includes thermal pyrolysis, oxidation, and polymerization, is complicated. The identification of products and investigation of reaction process can effectively explain the cause of deterioration mechanism of aero lubricating oil at high temperature, which can provide the theoretical basis for developing new and high-end lubricating oils.

The tested aero lubricating oil is a kind of synthetic lubricating oil with diisooctyl sebacate (DIOS) as its based oil, which has been extensively used in a certain type of aircraft engine lubrication system. The lubricating properties of aero lubricating oil will change due to deterioration caused by high temperature, high pressure, and high shearing, along with metallic catalysis (i.e., copper and iron) under the conditions of being exposed to the air. The deteriorated oil will do harm to the functions of the engine afterwards [6, 7]. In recent years, the deterioration of diester lubricating oil was focused on the performance deteriorated at high temperatures [811]. Chen et al. explored the change about antioxidants during the decay of some aero lubricating oil. It was found that thermal oxidation of antioxidant was a pseudo-first-order reaction and the equation of reaction kinetics was obtained [8]. Fei et al. analyzed the pyroreaction products of diisooctyl adipate of aero lubricating oil using gas chromatograph/mass spectrometer (GC/MS) and indicated that the formation of substances (i.e., ketones, ethers, alcohols, and acids) was the primary cause of color deepening and increase of acid number [9]. Wu et al. simulated the oxidation of DIOS to investigate the lubricating properties of oil products under different degrees of oxidation by a four ball tester. The results showed that the formation of peroxide during the oxidation process of lubricating oil led to the deterioration of lubricating properties of oil products and occurrence of some polar products decreased abrasion loss [10]. Santos et al. analyzed the product of thermal deterioration by using FTIR and GC/MS, who found that the structure change was related with property change [11]. In these studies, the effect of factors and property changes of diester-like lubricating oil were focused on thermal oxidation. However, few studies concern the process and mechanism of thermal deterioration.

In the present investigation, some aero lubricating oil was subjected to simulating its oxidation under different high temperatures using the simulative device and subsequently analyzed by GC/MS. The deterioration mechanism was focused on investigation. This is of a great significance in improving the high-temperature performance of an aero lubricating oil, determining the appropriate oil change intervals and realizing the long-term quality monitoring on aero lubricating oil.

2. Experimental Section

2.1. Materials

Some aero lubricating oil was collected from some Fuel Research Institute. The reagents used in the experiment are analytical ones which are commercially available. All reagents (petroleum ether, n-hexane, acetone, and so on) used in the experiments were analytical reagents, and all the organic solvents had been distilled before use.

2.2. Simulation Testing on High-Temperature Oxidation

128 g aero lubricating oil was added into a device (500 mL volume, 32 MPa, 450°C, 1100 r/min, and 2 kW, SongLing Co. Ltd, Yantai, China) simulating the operating conditions of the engine. The experimental lubricating oils were heated to the required temperatures (180, 200, 230, 250, 270, and 300°C) for 2 h, respectively, and the stirring rate was 800 r/min. For the convenience of description, the six experimental oils were marked with EO180, EO200, EO230, EO250, EO270, and EO300, respectively. After the reaction, the device was immediately placed in ice water until room temperature. The experimental oils were filtered and kept in dark conditions.

2.3. Acid Value Testing

The determination of acid values in testing samples is made in accordance with GB/T 264-1983(1991) Standard Testing Methods.

2.4. GC/MS Analyses

Oil samples were analyzed with a Hewlett-Packard 6890/5973 GC/MS, which was equipped with a capillary column coated with HP-5MS (cross-link 0.5% PH ME siloxane, 60 m length, 0.25 mm inner diameter, 0.25 μm film thickness) and a quadrupole analyzer with an m/z range from 33 to 500 and operated in electron impact (70 eV) mode. The capillary column was heated from 120 to 274°C at a rate of 13°C min−1 and held for 2 min, then raised to 281°C at a rate of 0.5°C and held for 2 min, finally raised to 300°C at a rate of 12°C and held at 300°C for 3 min. Data were acquired and processed using software of Agilent MSD Productivity Chemstation. Compounds were identified by comparing mass spectra with NIST05a library data.

3. Results and Discussion

3.1. Color and Molecular Compositions of Oils

As a direct appearance index, color change of oils can be determined by various factors, including both internal ones (base oil, additive, oil pigment, and so forth) and external conditions (temperature, high pressure, high shearing, metal catalysis, oxidation, run time, and so forth) [12]. In this study, color of oils in different high-temperature reactions became more noticeable. EO180 is almost pale yellow and transparent at 180°C. As the reaction temperature rose, the color gradually deepens. It is worth noting that color becomes most remarkable at 230°C, even looking reddish brown. EO300 became not transparent but showed deep chocolate brown at 300°C. Most of aero lubricating oils were undergone significant color change under the high temperature, which provided a clue to explore the performance analysis for aero lubricating oils.

Figure 1 listed the total ion chromatogram of EO180–EO300 before 20.4 min. As shown in Figure 1, in total, 50 compounds were detected with GC/MS, which included alkanes, alkenes, alcohols, acids, amines, ketones, monoesters, and diesters, and were displayed in Table 1. As demonstrated in Table 1, ester compounds dominated in detected compositions, which were 25 compounds. In addition, some chromogenic compounds are detected in EO180–EO300, including amines (peak 23, 25), phosphates (peak 30, 33, 42, 44–47), ketones (peak 12, 31, 36), and acids (peak 11, 43). Though few in content, they played a crucial role in significantly deepening color of aero lubricating oils. Meanwhile, these compounds, stronger in polarity, contributed to the enhancement of the acid number, increasing from 0.173 mg KOH/g in EO180 to 10.450 mg KOH/g in EO300.

3.2. The Deterioration Mechanism of Oils

Temperature is one of the most important factors for the deterioration of aero lubricating oil. As displayed in Figure 1 and Table 1, the product amounts were markedly increased with raising temperature and reached maxima at 300°C and properties of aero lubricating oil change with the oil’s compositions. The deterioration of oils is generally considered tending to form free radicals and follow the chain reactions under high temperature and oxygen conditions. But little work has been published to date about the deterioration mechanism of aero lubricating oil. We focus our attention on possible reaction mechanism at the molecular level in order to slower or prevent oil deterioration. As shown in Scheme 1, possible chemical reactions are thermal pyrolysis, thermal oxidation, and thermal polymerization according to detected compounds in Table 1.

3.2.1. Thermal Pyrolysis

DIOS, as based oil of experimental oil, is a long-chain diester with favorable symmetric structure with presented hydrogen of β-carbon at alcohol side. Hydrogen of β-carbon at alcohol side and oxygen of ester carbonyl groups formed intramolecular hydrogen bond by molecular movement, forming six-membered ring with C, O, and H atoms [13]. At high temperature, hexatomic ring was cracked into free radical I and II (Scheme 1(a)), and then free radical I and II recurred disproportionation reaction and generated 10-[(2-ethylhexyl)oxy]-10-oxodecanoate and 2-ethylhexene (peak 4, Scheme 1(b)). Along with the increase of reaction temperature, the relative abundances of 2-ethylhexene (peak 4) in EO180 to EO300 were 0.018, 0.012, 0.068, 0.293, 0.500, and 5.213%, respectively, indicating the pyrolysis extent of oil were significantly enhanced with raising temperature. 2-ethylhexene further produced ethylene and hexylene at the higher temperature (Scheme 1(c)). As depicted in Scheme 1(d and e), parts of free radical II reacted with ethyl free radical and ethylene to generate 3-ethyloctane and 4-ethyloctene, respectively.

According to the structural formula, DIOS presented straight chain with eight carbons between ester groups. The straight chain could be cracked at high temperature, which is similar to straight-chain alkanes. The bonding energy of C-H bond of alkanes was higher than that of the C-C bond; therefore, homolysis of thermal pyrolysis started with C-C bond [14, 15], so did DIOS. All C-C bonds between ester groups can cause homolytic reaction at high-temperature conditions. The generated free radicals caused disproportionation reaction to produce saturation and unsaturation monoester. The reaction processes and products of the cracked C-C bond at different positions will be consequently discussed with the basis of GC/MS analysis.

As exhibited in Scheme 1, when the breakpoint is at the C11-C12 bond, DIOS could homolytically cracked two III free radicals (f). When two free radicals happened to have a collision, it will lead to the loss of H·and generated unsaturated 2-ethylhexyle-4-olefine acid monoester (C), whereas the other free radical generated saturated 2-ethylhexyl-olefine acid monoester (B). When the breakpoint is at the C8-C9 bond, DIOS generated IV and V free radicals and then two IV free radicals can generate low molecular weight di-2-ethylhexyl diester by coupling reaction (D). In this system, II free radical attacked the β-carbon of V free radical to generate VII free radical and alkyl radical with molecular weight of 141, whereas alkyl radical lost H atom and formed the alkene with molecular weight of 140 (Scheme 1(j and k)). When point of fracture is at the C10-C11 bond, DIOS generated two VII and VIII free radicals, and two VIII free radicals bumped together and formed caprylyl glycol adipate (E) by coupling reaction (Scheme 1(m)). VIII free radical was oxidized by oxygen at some temperature and formed the 6-(2-ethylhexyloxy)-6-diakyl hexylic acid (Scheme 1(n)). When the breakpoint is at the C9-C10 bond, DIOS could generate two free radicals and then formed diisooctyl adipate (F) by coupling reaction. Table 2 displayed the part ester compounds of EO300.

Spatial position and the near groups varied with the type of the C-C bond, resulting in different interactions involved. Therefore, the hemolytic cleavage of the different C-C bonds at high temperatures leads to the different abilities of free radicals. Generally, bond length of chemical bond is inversely proportional to the bond energy: the more low bond energies, the more crack of chemical bond. Zhou et al. [16] calculated the bonding energies of C-C bond of n-decane and xylene by computational chemistry method. The results indicated that the low bonding energy of n-decane can more easily cause thermal pyrolysis.

The structure of DIOS was optimized by using semiempirical method (PM3 method) with an aid of Hyperchem 7.0 software (Figure 2). Table 3 exhibited the bond length of various C-C bonds between ester groups. The fitted results of HyperChem indicated that the bonding length of the C7-C8 bond was significantly lower than that of other C-C bonds, revealing that C7-C8 bond was not easy to break. The difference in bond length of other four C-C bonds suggested that the C-C bond could be broken at high temperature, which was consistent with the deterioration mechanism of DIOS as based oil. Thermal pyrolysis included the cracking of six-membered ring and long carbon chain between ester groups. The cracking of long carbon chain between ester groups at different positions formed the different free radicals [17]. The collision of free radicals caused coupling and disproportionation reaction, resulting in formation of unsaturation and saturation monoesters, diesters with molecular weight less than DIOS, and part diesters with molecular weight more than DIOS.

3.2.2. Thermal Oxidization

Besides thermal pyrolysis, DIOS can cause thermal oxidization by the effect of oxygen under metal catalysis and high-temperature conditions. Alkene and reactive free radicals derived from thermal pyrolysis could be oxidized to form acid oxygen-containing compounds (peaks 11, 12, 31, 36, and 43), which lead to increasing acid number. Table 4 listed the acid number of experimental oils under different temperatures. As shown in Table 4, the acid number of EO180 is 0.173 mg KOH/g, which was lower than critical value (0.5 mg KOH/g) with less corrosion for engine. However, the acid number was 1.011 mg KOH/g at 250°C, which could mildly lead to the corrosion of the engine. Furthermore, when the heated temperature increases to 300°C, the acid number dramatically reached to 10.450 mg KOH/g, which meant that the engine was corroded severely and the aero lubricating oil must be replaced.

3.2.3. Thermal Polymerization

The deterioration process not only is the cleavage of bonds but also includes polymerization, especially polycondensation at high temperature. It was reported that the oxidation products of lubricating oil could be condensed to polyoxides and then further formed the macromolecules [18, 19]. As expected from the GC/MS results, compounds of high molecular weight were detected in total ion chromatograms after 20.4 min. Due to the disadvantage of GC/MS, which only detects compounds with a molecular weight of less than 500, compounds of high molecular weight could not be detected and identified. Therefore, further research will focus on identifying the macromolecules from oils. These macromolecules, which combined with degraded products of additives and wear metallic particles, formed oil sludge. Oil sludge could be dissolved into oils and/or deposited to the surface of engine or blocked the strainer and gallery, which decreased lubrication effect due to lack of oil supply.

4. Conclusions

In summary, it is demonstrated that some aero lubricating oil significantly cause deterioration with air under high temperature. According to analysis with GC/MS, three reactions were presented, which mainly included thermal pyrolysis, thermal oxidation, and thermal polymerization, and thermal pyrolysis dominated at high temperature. Thermal pyrolysis included the pyrolysis of six-ring esters and pyrolysis of long carbon chain of ester groups, resulting in formation of acid, alkene, and various reactive intermediates. And thermal reactions between alkene/reactive intermediates and oxygen generated chromogenic compounds, such as alcohol, aldehyde, and acid. In addition, coupling and disproportionation reactions were observed by collision of free radicals, which generated unsaturated monoester, saturated monoester, diesters, and high-molecular-height polymers. The thermal pyrolysis of DIOS generated acid substances, and derivative of part additives resulted in the increase of acid number of oil products. Moreover, these products influenced the aero lubricating oil properties. The products of thermal oxidation were ester- and hydrocarbon-like compounds. The former and the latter were the chromophoric and auxochromous substance, respectively, which lead to the dark color of oil products after the oxidation process. The thermal polymerization generated the large molecular weight ester compounds. Then these ester compounds and degradation products generated oil sludge. The overabundance of oil sludge will block oil line and decreased the lubrication effect afterwards.

Conflicts of Interest

The authors declare that they have no conflicts of interest.

Acknowledgments

Financial supports from the Project of Youth Fund of Jiangsu Province (no. BK20150166), Scientific Researching Youth Fund Projects of Air Force Logistics College (no. 2016xkjq006), Natural Science Foundation of the Anhui Higher Education Institutions of China (no. KJ2017A400), and National Natural Science Fund of China (no. 51575525) were acknowledged.