Analysis of Wireless Energy Harvesting Relay Throughput in Rician Channel

Hu, Yifan; Cao, Ning; Chen, Yunfei

doi:https://doi.org/10.1155/2016/8798494

Mobile Information Systems

On this page

Abstract Introduction System Model Discussion Conclusion References Copyright Related Articles

Research Article | Open Access

Volume 2016 | Article ID 8798494 | https://doi.org/10.1155/2016/8798494

Analysis of Wireless Energy Harvesting Relay Throughput in Rician Channel

Yifan Hu,¹Ning Cao,¹and Yunfei Chen²

Academic Editor: Francesco Gringoli

Received14 Jun 2016

Revised10 Oct 2016

Accepted23 Oct 2016

Published10 Nov 2016

Abstract

Cooperative communication uses idle nodes to achieve performance gains. Energy harvesting allows cooperative communication to be less dependent on batteries. In this paper, the performance of energy harvesting (EH) amplify-and-forward relaying is analyzed for Rician fading channels, in contrast to previous works that focused on Rayleigh fading channels. Continuous time EH protocol and discrete time EH protocol are considered. Analytical expressions for the average throughput are derived. Numerical results are presented to show the good performance of the system in Rician fading channels by examining various system parameters using the analytical expressions.

1. Introduction

Amplify-and-forward (AF) relaying is widely used in communication systems to extend network coverage or achieve diversity gain. In AF relaying, the information from the source node is received and amplified by the relay node before it is forwarded to the destination node. On the other hand, wireless energy harvesting has an important application in relaying. The relay node may be limited by its battery life so that it may count on some external power source to remain active in the network. In this case, energy harvesting is particularly useful, as the source node can act as an external power source for the relay node by transmitting energy wirelessly.

Several works have been done on either energy harvesting technique or amplify-and-forward relaying technique, to name a few. References [1–3] considered the use of energy harvesting from ambient radio frequency signals to power a wireless sensor network. References [4, 5] studied the transmission strategies for EH nodes. In these cases the nodes harvest energy at some time instant and transmit the harvested energy at some other time instants. In [4], the transmission time minimization was considered. Reference [5] studied the maximized short-time throughput for EH systems.

Reference [6] also studied ambient RF energy harvesting, but instead of using the harvested energy to power the wireless sensor network directly, it considered the option of storing the harvested energy in a capacitor or battery to power the wireless sensor network. In [7], a radio frequency energy harvesting model was analyzed by considering a receiving antenna part, a rectifying part, and an energy storage in the circuit. In [8], the optimum sampling of a random field was studied. Reference [9] studied the best-effort sensing with finite battery. The optimum estimation of a continuous time random process using discrete time samples taken by a sensor with wireless power was studied in [10]. This work showed that, for the sensing of a time-varying random event with wireless power, the optimum performance is achieved when the energy-harvesting-consumption-ratio is 1. In other studies, the optimal placement of the relay node was also studied. For example, [11] considered a dual-hop energy transfer scheme, while [12] presented a novel optimization problem for two-hop RF energy transfer to improve wireless energy transfer efficiency. In [13], artificial noise was added to reduce the information leakage rate for energy receivers while satisfying its energy harvesting requirements. Reference [14] considered a wireless energy harvesting enabled massive multiple-input-multiple-output relaying system in order to provide wireless security. A protocol using one part of each frame for energy harvesting and the other part for message transmission was considered in [15]. In [16], the optimum performance boundaries of a two-hop multiantenna AF relaying system with a multiantenna energy harvesting (EH) receiver were studied. Also, energy harvesting techniques for practical devices in low-power applications were studied using energy harvesting relaying in [17–19]. Reference [20] studied the different rate-energy trade-offs in order to achieve the optimal source and relay coding in a multiple-input-multiple-output relay system. Reference [21] proposed two protocols of energy harvesting AF relaying and analyzed the throughput of each protocol (continuous time EH protocol and discrete time EH protocol). All the above works have been conducted for Rayleigh fading channels. However, it is well known that Rayleigh fading channel is only a special case of the Rician fading channel when the line of sight is 0. Thus, the Rician fading channel is more general and useful than the Rayleigh fading channel, and it is of great interest to investigate the performance EH relaying in Rician fading channel.

In this paper, we fill this gap by analyzing the performance of energy harvesting AF relaying in Rician fading channels. We consider two EH protocols, similar to [21], as continuous time EH protocol and discrete time EH protocol. Based on these protocols, we derive the analytical expression for the throughput in the Rician fading channels, which is more challenging due to the Bessel function in its probability density function. Numerical results are presented to compare the Rician fading channel with the Rayleigh fading channel. They show that the performance in Rician fading channel is better than that in Rayleigh fading channel and this performance gain can be quantified using our results.

The rest of this paper is organized as follows. Section 2 presents the system model of AF relaying system with energy harvesting. In Section 3, we derive the analytical expression for the throughput of each protocol in Rician fading channel. In Section 4, we show the numerical examples obtained from the analytical expressions and verify its accuracy using computer simulation. Section 5 concludes the paper.

2. System Model

We consider a cooperative communication scenario constituted by a source node (), a destination (), and an intermediate relay node (). The source node and the destination node are not energy-constrained, but the relay node is energy-constrained. We assume that the destination node can not communicate directly with the source because of physical obstacles. This is a valid assumption in some communication scenarios. Then, deploying EH relay nodes will be a good solution to make the communication between source and destination work effective.

The following assumptions of relaying model are used in this work.(1)The processing power used for the circuit at the relay is negligible compared with the transmission power required by the relay.(2)The energy-constrained relay node first harvests sufficient energy from the source and then the relay node relays the source information to the destination using the harvested energy. The battery capacity at the relay is much larger than the required transmission power.(3)The relay adopts the time-switching (TS) architecture. It spends a portion of time for energy harvesting (EH) and the remaining time for information transmission (IT).(4)The and channels are composed of Rician fading and large-scale path loss. We denote the distances between and as and , respectively. The channel fading gains between and are denoted, respectively, as and . The fading channel gains are assumed to be constant over a period of seconds and are independent and identically distributed from one block to the other.(5)Assume that the communication happens in blocks of seconds, each of which is composed of two parts: EH part and IT part. We denote the fraction of time allocated for EH in the block as . Thus, EH part takes seconds, IT part takes seconds, and IT part takes seconds. For continuous time EH, the relay harvests energy and transmits information within each block. Thus, [21]. For discrete time EH, the relay uses the whole block for energy harvesting or transmission. When the relay harvests energy, , while when the relay transmits the information, [21].(6)For continuous time EH, an EH-IT block contains EH part and IT part, where EH occupies a portion of the block and IT occupies the rest. For discrete time EH, an EH-IT pattern contains blocks, where there are EH blocks and one IT block ().

Also, we define the following symbols:: the available energy at the start of an EH-IT pattern : the available energy at the start of the th block : the harvested energy at the time instant in the th block : the energy harvested in an EH block : EH-IT pattern start time : the number of EH blocks of discrete time EH protocol.

2.1. Signal Model

For the th block, the source node sends the normalized information signal with through the channel, which is received at the relay node as .where is the fading channel gain, is the distance from source to the relay, is the path loss exponent, is the source transmission power, and is the additive white Gaussian noise (AWGN) with mean zero and variance .

Then, the AF relay harvests enough energy to guarantee the required transmission power in the IT part. For the general case, can be any value set by the requirements of the application QoS, which will produce different throughput. After the EH part, the relay amplifies the received signal and forwards it to the destination node. The signal sent by relay iswhere is the average power of such that

Finally, the signal received by the destination node is given by

In (4), is the fading channel gain, is the distance of the link, and is the AWGN at the destination node. From (4), we can distinguish the signal part and the noise part, where is the signal part and is the noise part. Thus we can get the signal-to-noise ratio (SNR) at the destination node aswhere again is the variance of AWGN at node.

For the th block, if the SNR is less than the threshold SNR () there will be outage. So we get the outage indicator aswhere is an indicator function which is equal to 1 if its argument is true; otherwise it is 0.

2.2. EH Relay Protocols

2.2.1. Continuous Time EH Protocol

In this protocol, the relay harvests the energy just enough to transmit the information signal. The continuous time EH relay makes sure that the relay can harvest the required amount of energy within each block and transmit it to the destination node. The EH-IT pattern only has one block [21].

As Figure 1 shows, firstly the relay spends seconds on harvesting energy, where . Then, in the IT part, half of the time is for transmission and the other half time is for transmission. The energy harvested in the EH time will be consumed in the IT time, so that the accumulated harvested energy is 0. Thus, .

In this case, the harvested energy during seconds is given bywhere is the energy conversion efficiency. The relay needs to forward the source message to the destination node with a transmission power for a time of . We can get the relation asSo, combining (7) and (8), we can get

In this paper, throughput means the proportion of the effective communication time to the total time when the relaying transmission succeeds. As is the effective communication time within one block of time , the throughput is calculated asThe throughput in (10) is a function of the channel gains and . They are random variables. Thus, the average throughput is

2.2.2. Discrete Time EH Protocol

In this protocol, each block is used either for EH or for IT. If , the block is used for EH. Otherwise, it is used for IT. Within the IT part, is used for transmission, and the rest is for transmission.

In Figure 2, if , there will be EH blocks, and EH will continue until . Then, the relay starts the IT. However, if at the beginning, there will be no EH part , and the relay will start IT immediately. In this case, we can see that the harvested energy may not be completely consumed, so that can be bigger than zero [21].

In this case, when a block is used for EH, the harvested energy will be

Then

Similarly, the throughput of the discrete time EH is also , and the average throughput iswhere .

3. Performance Analysis in Rician Fading Channels

In this section, we will derive the analytical expression for the throughput of each protocol in Rician fading channels.

3.1. Average Throughput of Continuous Time EH Protocol

Since and are independent, (11) can be written asThe function of is given byFor convenience, we define , , , and . Then we have

We assume the channel gain is Rician distributed. Thus, the PDF of or is given bywhere is the power of the cluttery component and is the amplitude of the line-of-sight component. Using the transformation , or has the PDF of

Then, we get that isHere, we can see that when , .

Finally we get the average throughput by taking the PDF of into the formula as

One sees that this is a two-dimensional nested integral, which is not easy to be computed numerically due to convergence issue. So we should do some simplifications. We notice that, in (20), we can get . For , it is . In general cases, the SINR will not be very small, so is much smaller than 1. So (20) can be approximated as

Also,

On the other hand, for , we use the substitution to havewhere function is defined asThen, (25) can beSo we get

Combining (21) and (27), we get

Then we havewhere .

As we can see (29) is a one-dimensional integral from 0 to , and due to the exponential function and the Bessel function, the integrand of this integral converges very quickly.

3.2. Average Throughput of Discrete Time EH Protocol

Since and has the PDF of (19), one haswhere is the dummy variable for the random variable , , and the mean of is .

In the above, the harvested energy is . The leftover energy at the end of the first EH-IT pattern after consuming in the IT part is . Afterwards, for the second EH-IT pattern, if the leftover energy of the first EH-IT pattern is smaller than , it will be for the second EH-IT pattern, but if it is larger than , it is also of the second EH-IT pattern and will consume another energy without energy harvesting. This process continues. We can deduce that the leftover energy at the end of any EH-IT pattern, in a sequence of EH-IT patterns, can be transformed to the same form as which is a function of , , and . Consequently, the harvested energy available at the start of any EH-IT pattern, , will have the PDF:

We have

In this case, is independent of the EH time, , but it depends on the fading channels, and ; also depends on the accumulated harvested energy at the start of the block, . Thus, depends on fading channels of the previous blocks, or . So the throughput can be written as

Using the results of (20) and (27), we can get

At the same time, we set as the number of the total EH blocks. Then we denote as the number of EH blocks just before the energy arrives . If , there will be . When , we have known that the mean of is . Then we can get .

So we have

Thus

So we have

We use function considered before again, to getwhere .

From the definition of throughput we have

Combining (34) and (39), the average throughput is

4. Numerical Result and Discussion

In this section, numerical results are presented to show the throughput of the system in Rician fading channels. The source transmission power is set to dBm. The path loss exponent is set to . The distance from source to relay is set to meters and the distance from relay to destination is set to meters. The energy conversion efficiency is set to . The threshold SNR is set to dB. The noise variances at the relay and the destination nodes are set to dBm and dBm. Also, , which is the same as in the Rayleigh fading channel. We also obtain the simulation results to verify the analytical results obtained in Section 3. In the simulation, 100000 blocks are used, where we generate independent fading channels and for each block. We assume fixed power transmission at the relay so that is fixed while changes with , similar to [21].

Figure 3 shows the comparison of analytical and simulation results for the throughput of discrete time EH and continuous time EH in Rician fading channel. From Figure 3 we can see that the simulation and analytical result of the throughput of continuous time EH and discrete time EH in Rician fading channel match well. This shows the accuracy of the approximation we used. In addition, we can find that there is a peak in the curve. It is because the throughput is related to both the final SNR and the time for EH. When increases the final SNR will be larger so that the outage probability will decrease, which makes the throughput larger. On the other side, when becomes bigger, the time for EH will be more, which can decrease the throughput. Therefore, there will be that makes the throughput the biggest, which is the optimal. Moreover, we can see that the performance of discrete time EH protocol is better than that of continuous time EH protocol. There is energy left after a EH-IT pattern of discrete time EH protocol will harvest more energy when is larger. Then it makes the EH time of the following EH-IT pattern smaller, so that the throughput will be larger.

In Figure 4, the value of increases from dBm to dBm. The performance of the throughput of discrete time EH and continuous time EH in Rayleigh and Rician fading channels can be compared. From the result, we can see that the throughput in Rician fading channel is higher than that in Rayleigh fading channels under the same other conditions. It conforms to the physical truth that the Rician fading channel is a better fading channel than Rayleigh fading channel, such that performance in Rician fading channel should be better than that in the Rayleigh fading channel.

Figure 5 plots the optimal throughput when the noise variance at the destination nodes increases form dBm to dBm, so that the throughput also changes when the noise variance changes. The optimum throughput decreases when the noise variance increases. When the noise becomes bigger, needs to be bigger to satisfy the outage condition, which will make the EH time longer, and finally, makes the throughput decrease.

Figure 6 shows the optimal throughput versus the threshold SNR when it increases from dB to dB. We can see that when the threshold SNR increases the throughput decreases. The higher threshold SNR needed, the higher final SNR should be, and it will require higher , which will make the EH time longer to decrease the throughput. When the threshold SNR increases, the gap between the simulation and analytical results increases, because when the threshold SNR increases the sensibility to will be bigger, so the approximation becomes inaccurate in this case.

In Figure 7, we examine the line of sight effect. The throughput when is larger than that when . When the line of sight increases, that is, the channel becoming better, the throughput will increase.

5. Conclusion

In this paper, we have derived the analytical throughput of continuous time and discrete time EH protocols used in AF relay in Rician fading channel and have proved the accuracy of the analytical throughput by computer simulation. In addition, we also discussed the performances in different situations for different transmit power of the relaying node, noise at the receive node, and threshold SNR. Moreover, the performance of the EH-IT protocols in Rician fading channel is better than that in Rayleigh fading channel, because of the channel improvement from the line of sight. In addition, the throughput will change while changes and there is a peak to attain the optimal throughput, and the optimal throughput will decrease when the noise and threshold SNR increases.

Competing Interests

The authors declare that they have no competing interests.

References

A. M. Zungeru, L. M. Ang, S. Prabaharan, and K. P. Seng, “Radio frequency energy harvesting and management for wireless sensor network,” in Green Mobile Devices and Networks: Energy Optimization and Scavenging Techniques, pp. 341–368, CRC Press, 2012.
View at: Google Scholar
D. Bouchouicha, F. Dupont, M. Latrach, and L. Ventura, “Ambient RF energy harvesting,” in Proceedings of the International Conference on Renewable Energies and Power Quality (ICREP '10), Granada, Spain, March 2010.
View at: Google Scholar
H. Jabbar, Y. S. Song, and T. T. Jeong, “RF energy harvesting system and circuits for charging of mobile devices,” IEEE Transactions on Consumer Electronics, vol. 56, no. 1, pp. 247–253, 2010.
View at: Publisher Site | Google Scholar
J. Yang and S. Ulukus, “Optimal packet scheduling in an energy harvesting communication system,” IEEE Transactions on Communications, vol. 60, no. 1, pp. 220–230, 2012.
View at: Publisher Site | Google Scholar
K. Tutuncuoglu and A. Yener, “Optimum transmission policies for battery limited energy harvesting nodes,” IEEE Transactions on Wireless Communications, vol. 11, no. 3, pp. 1180–1189, 2012.
View at: Publisher Site | Google Scholar
T. Beng Lim, N. M. Lee, and B. K. Poh, “Feasibility study on ambient RF energy harvesting for wireless sensor network,” in Proceedings of the IEEE MTT-S International Microwave Workshop Series on RF and Wireless Technologies for Biomedical and Healthcare Applications (IMWS-BIO '13), pp. 1–3, Singapore, December 2013.
View at: Google Scholar
H. ElAnzeery and R. Guindi, “Frequency survey simulation for developing novel radio frequency energy harvesting model,” in Proceedings of the 14th International Conference on Modelling and Simulation (UKSim '12), pp. 476–479, March 2012.
View at: Publisher Site | Google Scholar
K. Ritter, G. W. Wasilkowski, and H. Wozniakowski, “Multivariate integration and approximation for random fields satisfying Sacks-Ylvisaker conditions,” The Annals of Applied Probability, vol. 5, no. 2, pp. 518–540, 1995.
View at: Publisher Site | Google Scholar | MathSciNet
J. Yang, X. Wu, and J. Wu, “Adaptive sensing scheduling for energy harvesting sensors with finite battery,” in Proceedings of the IEEE International Conference on Communications (ICC '15), June 2015.
View at: Google Scholar
J. Wu, I. Akingeneye, and J. Yang, “Optimum sensing of a time-varying random event with energy harvesting power sources,” in Proceedings of the IEEE International Symposium on Information Theory (ISIT '15), pp. 1134–1138, Hong Kong, June 2015.
View at: Publisher Site | Google Scholar
A. Kurs, A. Karalis, R. Moffatt, J. D. Joannopoulos, P. Fisher, and M. Soljačić, “Wireless power transfer via strongly coupled magnetic resonances,” Science, vol. 317, no. 5834, pp. 83–86, 2007.
View at: Publisher Site | Google Scholar | MathSciNet
D. Mishra and S. De, “Optimal relay placement in two-hop RF energy transfer,” IEEE Transactions on Communications, vol. 63, no. 5, pp. 1635–1647, 2015.
View at: Publisher Site | Google Scholar
L. Liu, R. Zhang, and K.-C. Chua, “Secrecy wireless information and power transfer with MISO beamforming,” IEEE Transactions on Signal Processing, vol. 62, no. 7, pp. 1850–1863, 2014.
View at: Publisher Site | Google Scholar | MathSciNet
X. Chen, J. Chen, and T. Liu, “Secure wireless information and power transfer in large-scale MIMO relaying systems with imperfect CSI,” https://arxiv.org/abs/1407.5355.
View at: Google Scholar
S. Luo, R. Zhang, and T. J. Lim, “Optimal save-then-transmit protocol for energy harvesting wireless transmitters,” in Proceedings of the IEEE International Symposium on Information Theory (ISIT '12), pp. 955–959, IEEE, Cambridge, Mass, USA, July 2012.
View at: Publisher Site | Google Scholar
B. K. Chalise, W.-K. Ma, Y. D. Zhang, H. A. Suraweera, and M. G. Amin, “Optimum performance boundaries of OSTBC based AF-MIMO relay system with energy harvesting receiver,” IEEE Transactions on Signal Processing, vol. 61, no. 17, pp. 4199–4213, 2013.
View at: Publisher Site | Google Scholar
I. Krikidis, “Simultaneous information and energy transfer in large-scale networks with/without relaying,” IEEE Transactions on Communications, vol. 62, no. 3, pp. 900–912, 2014.
View at: Publisher Site | Google Scholar
Y. Zeng and R. Zhang, “Full-duplex wireless-powered relay with self-energy recycling,” IEEE Wireless Communications Letters, vol. 4, no. 2, pp. 201–204, 2015.
View at: Publisher Site | Google Scholar
A. A. Nasir, X. Zhou, S. Durrani, and R. A. Kennedy, “Relaying protocols for wireless energy harvesting and information processing,” IEEE Transactions on Wireless Communications, vol. 12, no. 7, pp. 3622–3636, 2013.
View at: Publisher Site | Google Scholar
B. K. Chalise, Y. D. Zhang, and M. G. Amin, “Energy harvesting in an OSTBC based amplify-and-forward MIMO relay system,” in Proceedings of the IEEE International Conference on Acoustics, Speech, and Signal Processing (ICASSP '12), pp. 3201–3204, March 2012.
View at: Publisher Site | Google Scholar
A. A. Nasir, X. Zhou, S. Durrani, and R. A. Kennedy, “Wireless-powered relays in cooperative communications: time-switching relaying protocols and throughput analysis,” IEEE Transactions on Communications, vol. 63, no. 5, pp. 1607–1622, 2015.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2016 Yifan Hu et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

903

Downloads

791

Citations