Table of Contents Author Guidelines Submit a Manuscript
Mathematical Problems in Engineering
Volume 2010, Article ID 671062, 12 pages
http://dx.doi.org/10.1155/2010/671062
Research Article

Dynamic MRR Function Optimization Using Calculus of Variations

Department of Information Management, Yu Da University, Miaoli County 361, Taiwan

Received 19 February 2010; Accepted 22 April 2010

Academic Editor: Jyh Horng Chou

Copyright © 2010 Tian-Syung Lan. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. W. Y. H. Liew and X. Ding, “Wear progression of carbide tool in low-speed end milling of stainless steel,” Wear, vol. 265, no. 1-2, pp. 155–166, 2008. View at Publisher · View at Google Scholar · View at Scopus
  2. W. Grzesik, “Influence of tool wear on surface roughness in hard turning using differently shaped ceramic tools,” Wear, vol. 265, no. 3-4, pp. 327–335, 2008. View at Publisher · View at Google Scholar · View at Scopus
  3. M. Cámara, J. Ortega, and F. de Toro, “A single front genetic algorithm for parallel multi-objective optimization in dynamic environments,” Neurocomputing, vol. 72, no. 16–18, pp. 3570–3579, 2009. View at Publisher · View at Google Scholar · View at Scopus
  4. A. Iqbal, H. Ning, I. Khan, L. Liang, and N. U. Dar, “Modeling the effects of cutting parameters in MQL-employed finish hard-milling process using D-optimal method,” Journal of Materials Processing Technology, vol. 199, no. 1–3, pp. 379–390, 2008. View at Publisher · View at Google Scholar · View at Scopus
  5. I. Ferrer, J. Rios, and J. Ciurana, “An approach to integrate manufacturing process information in part design phases,” Journal of Materials Processing Technology, vol. 209, no. 4, pp. 2085–2091, 2009. View at Publisher · View at Google Scholar · View at Scopus
  6. D. W. Kim, Y. S. Lee, M. S. Park, and C. N. Chu, “Tool life improvement by peck drilling and thrust force monitoring during deep-micro-hole drilling of steel,” International Journal of Machine Tools and Manufacture, vol. 49, no. 3-4, pp. 246–255, 2009. View at Publisher · View at Google Scholar · View at Scopus
  7. W. J. Zong, Z. Q. Li, T. Sun, K. Cheng, D. Li, and S. Dong, “The basic issues in design and fabrication of diamond-cutting tools for ultra-precision and nanometric machining,” International Journal of Machine Tools and Manufacture, vol. 50, no. 4, pp. 411–419, 2010. View at Publisher · View at Google Scholar · View at Scopus
  8. J. V. Kadam, M. Schlegel, B. Srinivasan, D. Bonvin, and W. Marquardt, “Dynamic optimization in the presence of uncertainty: from off-line nominal solution to measurement-based implementation,” Journal of Process Control, vol. 17, no. 5, pp. 389–398, 2007. View at Publisher · View at Google Scholar · View at Scopus
  9. J. Chae and S. S. Park, “High frequency bandwidth measurements of micro cutting forces,” International Journal of Machine Tools and Manufacture, vol. 47, no. 9, pp. 1433–1441, 2007. View at Publisher · View at Google Scholar · View at Scopus
  10. S. Binsaeid, S. Asfour, S. Cho, and A. Onar, “Machine ensemble approach for simultaneous detection of transient and gradual abnormalities in end milling using multisensor fusion,” Journal of Materials Processing Technology, vol. 209, no. 10, pp. 4728–4738, 2009. View at Publisher · View at Google Scholar · View at Scopus
  11. I. Deiab, K. Assaleh, and F. Hammad, “On modeling of tool wear using sensor fusion and polynomial classifiers,” Mechanical Systems and Signal Processing, vol. 23, no. 5, pp. 1719–1729, 2009. View at Publisher · View at Google Scholar · View at Scopus
  12. A. Chiang, Dynamic Optimization, McGraw-Hill, New York, NY, USA, 1992.
  13. Q. Meng, J. A. Arsecularatne, and P. Mathew, “Calculation of optimum cutting conditions for turning operations using a machining theory,” International Journal of Machine Tools & Manufacture, vol. 40, no. 12, pp. 1709–1733, 2000. View at Publisher · View at Google Scholar · View at Scopus