Table of Contents Author Guidelines Submit a Manuscript
Mathematical Problems in Engineering
Volume 2015 (2015), Article ID 157951, 7 pages
Research Article

Study and Simulation of Deformation Mechanics Modeling of Flexible Workpiece Processing by Rayleigh-Ritz Method

1School of Information Engineering, Guangdong University of Technology, No. 100 Waihuanxi Road, Guangzhou Higher Education Mega Center, Mail Box B65, Guangdong 510006, China
2HSBC Software Development (Guangdong) Limited, Guangzhou, Guangdong, China

Received 8 May 2014; Accepted 17 June 2014

Academic Editor: Yoshinori Hayafuji

Copyright © 2015 Yaohua Deng et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. D. Yao-Hua, H. Wei, L. Qing-Fu, and W. Li-Ming, “Regression calculation model of flexible material processing deformation based on distributed sensors measurement,” Advances in Information Sciences and Service Sciences, vol. 3, no. 11, pp. 208–212, 2011. View at Publisher · View at Google Scholar · View at Scopus
  2. D. Yaohua and L. Guixiong, “ATS-FNN-based modeling and simulation for compensation prediction of FWP machining deformation,” Journal of South China University o f Technology (Natural Science Edition), vol. 40, no. 3, pp. 146–151, 2012. View at Google Scholar
  3. Z. Mei, Y. Wang, and Y. Fan, “Researching and simulating deformation of aircraft structure part in NC machining,” Acta Aeronautica et Astronautica Sinica, vol. 26, no. 2, pp. 234–239, 2005. View at Google Scholar · View at Scopus
  4. W. Yunqiao, M. Zhongyi, and F. Yuqing, “Research on deformation in NC machining of aerospace thin-walled structure part,” Machinery Manufacturing Engineer, vol. 1, pp. 31–33, 2005. View at Google Scholar
  5. Z. Wang, N. He, K. Wu et al., “Analysis and control approach for machining deflection of thin-walled workpiece,” China Mechanical Engineering, vol. 13, no. 2, pp. 114–117, 2002. View at Google Scholar · View at Scopus
  6. W. Kai, H. Ning, and L. Wenhe, “Selection of cutting parameters in high speed milling of thin-walled structure components based on the machining errors control,” Mechanical Science and Technology, vol. 24, no. 7, pp. 788–791, 2005. View at Google Scholar
  7. Y. Deng, S. Chen, and J. Chen, “Deformation-compensated modeling of flexible material processing based on T-S fuzzy neural network and fuzzy clustering,” Journal of Vibroengineering, vol. 16, no. 3, pp. 1455–1463, 2014. View at Google Scholar
  8. C. Li, Y. Zhang, and J. Xu, “Numerical simulation of draping and buckling of woven fabric,” Journal of Tianjin University Science and Technology, vol. 40, no. 1, pp. 46–50, 2007. View at Google Scholar · View at Scopus
  9. S. F. Chen, J. L. Hu, and J. G. Teng, “A finite-volume method for contact drape simulation of woven fabrics and garments,” Finite Elements in Analysis and Design, vol. 37, no. 6-7, pp. 513–531, 2001. View at Publisher · View at Google Scholar · View at Zentralblatt MATH · View at Scopus
  10. A. Demiroz, “Prediction of large deformation behavior of fabric using Galerkin finite element method,” Textile Research Journal, vol. 75, no. 9, pp. 662–669, 2005. View at Publisher · View at Google Scholar · View at Scopus
  11. S. Pengcheng and H. Peixiang, “The developments of spline finite element method in computational mechanics,” Advances in Mechanics, vol. 30, no. 2, pp. 191–199, 2000. View at Google Scholar
  12. S. Gao and C. Zhou, “Research on differentiation of the cubic spline interpolation,” Science Technology and Engineering, vol. 8, no. 11, pp. 2948–2950, 2009. View at Google Scholar
  13. Y. Deng, Q. Lu, J. Chen, S. Chen, L. Wu, and L. Tang, “Study on the extraction method of deformation influence factors of flexible material processing based on information entropy,” Advances in Mechanical Engineering, vol. 2014, Article ID 547947, 8 pages, 2014. View at Publisher · View at Google Scholar