Table of Contents Author Guidelines Submit a Manuscript
Mathematical Problems in Engineering
Volume 2017, Article ID 4278082, 6 pages
https://doi.org/10.1155/2017/4278082
Research Article

A Consistent Relationship between the Stress and Plastic Strain Components and Its Application in Deep Drawing Process

School of Mechanical Engineering, Tongji University, Shanghai 201804, China

Correspondence should be addressed to Yong Zhang; moc.kooltuo@yz_ulg

Received 9 November 2016; Accepted 15 December 2016; Published 11 January 2017

Academic Editor: Hakim Naceur

Copyright © 2017 Yong Zhang et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. Z. R. Wang, Fundamental of Plastic Working Mechanics, National Defence Industry Press, Beijing, China, 1989.
  2. Z. R. Wang, “A consistent relationship between the stress- and strain-components and its application for analyzing the plane-stress forming process,” Journal of Materials Processing Technology, vol. 55, no. 1, pp. 1–4, 1995. View at Publisher · View at Google Scholar · View at Scopus
  3. W. L. Hu, Z. B. He, and Y. Fang, “Uniform principle on stress, strain and yield locus for analysing metal forming processes: the contribution of Prof. Z.R. Wang,” Journal of Materials Processing Technology, vol. 151, no. 1–3, pp. 27–32, 2004. View at Publisher · View at Google Scholar · View at Scopus
  4. B. Liu, L. Lang, Y. Zeng, and J. Lin, “Forming characteristic of sheet hydroforming under the influence of through-thickness normal stress,” Journal of Materials Processing Technology, vol. 212, no. 9, pp. 1875–1884, 2012. View at Publisher · View at Google Scholar · View at Scopus
  5. F. Dunne and N. Petrinic, Introduction to Computational Plasticity, Oxford University Press, New York, NY, USA, 2005. View at MathSciNet
  6. H. Takuda, K. Mori, I. Masuda, Y. Abe, and M. Matsuo, “Finite element simulation of warm deep drawing of aluminium alloy sheet when accounting for heat conduction,” Journal of Materials Processing Technology, vol. 120, no. 1–3, pp. 412–418, 2002. View at Publisher · View at Google Scholar · View at Scopus
  7. K. Ghavam, R. Bagheriasl, and M. J. Worswick, “Analysis of nonisothermal deep drawing of aluminum alloy sheet with induced anisotropy and rate sensitivity at elevated temperatures,” Journal of Manufacturing Science and Engineering, Transactions of the ASME, vol. 136, no. 1, Article ID 011006, 2014. View at Publisher · View at Google Scholar · View at Scopus
  8. A. H. Boogaard, Thermally enhanced forming of aluminum sheet (modeling and experiments) [Ph.D. thesis], University of Twente, Enschede, The Netherlands, 2002.
  9. S. S. Panicker, H. G. Singh, S. K. Panda, and R. Dashwood, “Characterization of tensile properties, limiting strains, and deep drawing behavior of aa5854-h22 sheet at elevated temperature,” Journal of Materials Engineering and Performance, vol. 24, no. 11, pp. 4268–4282, 2015. View at Publisher · View at Google Scholar · View at Scopus
  10. S. Kaya, G. Spampinato, and T. Altan, “An experimental study on nonisothermal deep drawing process using aluminum and magnesium alloys,” Journal of Manufacturing Science and Engineering, vol. 130, no. 6, Article ID 061001, pp. 863–881, 2008. View at Publisher · View at Google Scholar · View at Scopus
  11. H. Laurent, J. Coër, P. Y. Manach, M. C. Oliveira, and L. F. Menezes, “Experimental and numerical studies on the warm deep drawing of an Al-Mg alloy,” International Journal of Mechanical Sciences, vol. 93, pp. 59–72, 2015. View at Publisher · View at Google Scholar · View at Scopus