Table of Contents Author Guidelines Submit a Manuscript
Mathematical Problems in Engineering
Volume 2018, Article ID 3043712, 12 pages
https://doi.org/10.1155/2018/3043712
Research Article

Elastohydrodynamic Lubrication Characteristics of Spiral Bevel Gear Subjected to Shot Peening Treatment

1School of Mechanical Engineering, Tianjin Polytechnic University, Tianjin 300387, China
2The State Key Laboratory of Materials Processing and Die & Mould Technology, Huazhong University of Science and Technology, Wuhan 430074, China
3The State Key Laboratory of Mechanical Transmissions, Chongqing University, Chongqing 400044, China
4School of Mechanical Engineering & Automation, Beihang University, Beijing 100191, China

Correspondence should be addressed to Shuai Mo; moc.361@0102iauhsom

Received 23 January 2018; Revised 25 March 2018; Accepted 24 April 2018; Published 10 June 2018

Academic Editor: Fabrizio Greco

Copyright © 2018 Shuai Mo et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. L. Dimitrov, D. Michalopoulos, C. A. Apostolopoulos, and T. D. Neshkov, “Investigation of contact fatigue of high strength steel gears subjected to surface treatment,” Journal of Materials Engineering and Performance, vol. 18, no. 7, pp. 939–946, 2009. View at Publisher · View at Google Scholar · View at Scopus
  2. L. Guo, S. Zhou, L. Crocker, and A. Turnbull, “Initiation sites for cracks developed from pits in a shot-peened 12Cr martensitic stainless steel,” International Journal of Fatigue, vol. 98, pp. 195–202, 2017. View at Publisher · View at Google Scholar · View at Scopus
  3. S. Li and A. Anisetti, “A tribo-dynamic contact fatigue model for spur gear pairs,” International Journal of Fatigue, vol. 98, pp. 81–91, 2017. View at Publisher · View at Google Scholar · View at Scopus
  4. C. Zhou, Z. Xiao, S. Chen, and X. Han, “Normal and tangential oil film stiffness of modified spur gear with non-Newtonian elastohydrodynamic lubrication,” Tribology International, vol. 109, pp. 319–327, 2017. View at Publisher · View at Google Scholar · View at Scopus
  5. D. Gallitelli, V. Boyer, M. Gelineau et al., “Simulation of shot peening: from process parameters to residual stress fields in a structure,” Comptes Rendus (Doklady) de l'Academie des Sciences de l'URSS, vol. 344, no. 4-5, pp. 355–374, 2016. View at Publisher · View at Google Scholar · View at Scopus
  6. Y. Lv, L. Lei, and L. Sun, “Effect of microshot peened treatment on the fatigue behavior of laser-melted W6Mo5Cr4V2 steel gear,” International Journal of Fatigue, vol. 98, pp. 121–130, 2017. View at Publisher · View at Google Scholar · View at Scopus
  7. A. Terrin, C. Dengo, and G. Meneghetti, “Experimental analysis of contact fatigue damage in case hardened gears for off-highway axles,” Engineering Failure Analysis, vol. 76, pp. 10–26, 2017. View at Publisher · View at Google Scholar · View at Scopus
  8. W. Pu, J. Wang, R. Yang, and D. Zhu, “Mixed elastohydrodynamic lubrication with three-dimensional machined roughness in spiral bevel and hypoid gears,” Journal of Tribology, vol. 137, no. 4, Article ID 041503, pp. 1–11, 2015. View at Publisher · View at Google Scholar · View at Scopus
  9. C.-B. Tang, D.-X. Liu, B. Tang, X.-H. Zhang, L. Qin, and C.-S. Liu, “Influence of plasma molybdenizing and shot-peening on fretting damage behavior of titanium alloy,” Applied Surface Science, vol. 390, pp. 946–958, 2016. View at Publisher · View at Google Scholar · View at Scopus
  10. B. AlMangour and J.-M. Yang, “Improving the surface quality and mechanical properties by shot-peening of 17-4 stainless steel fabricated by additive manufacturing,” Materials and Corrosion, vol. 110, pp. 914–924, 2016. View at Publisher · View at Google Scholar · View at Scopus
  11. D. Trauth, J. Stanke, A. Shirobokov, P. Mattfeld, and F. Klocke, “Analysis of the fluid pressure, load capacity, and coefficient of friction of an elliptic machine hammer peened surface structure in hydrodynamic lubrication,” Production Engineering Research and Development, vol. 10, no. 6, pp. 539–550, 2016. View at Publisher · View at Google Scholar · View at Scopus
  12. V. V. Simon, “Optimal tooth modifications in face-hobbed spiral bevel gears to reduce the influence of misalignments on elastohydrodynamic lubrication,” Journal of Mechanical Design, vol. 136, no. 7, Article ID 071007, pp. 1–9, 2014. View at Publisher · View at Google Scholar · View at Scopus
  13. M. Shuai, Z. Yidu, and W. Qiong, “Research on multiple-split load sharing of two-stage star gearing system in consideration of displacement compatibility,” Mechanism and Machine Theory, vol. 88, pp. 1–15, 2015. View at Publisher · View at Google Scholar · View at Scopus
  14. M. Shuai and Z. Yidu, “Spiral bevel gear true tooth surface precise modeling and experiments studies based on machining adjustment parameters,” Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, vol. 229, no. 14, pp. 2524–2533, 2015. View at Publisher · View at Google Scholar · View at Scopus
  15. S. H. Yuan, H. L. Dong, and X. Y. Li, “Analysis of lubricating performance for involute gear based on dynamic loading theory,” Journal of Mechanical Design, vol. 134, no. 12, Article ID 121004, pp. 67–75, 2012. View at Publisher · View at Google Scholar · View at Scopus