Table of Contents Author Guidelines Submit a Manuscript
Scanning
Volume 2017 (2017), Article ID 2189614, 4 pages
https://doi.org/10.1155/2017/2189614
Research Article

Characterization of Surface Modification of 347 Stainless Steel upon Shot Peening

1School of Metallurgy and Materials Engineering, Chongqing University of Science & Technology, Chongqing 401331, China
2The Center of Material Analysis and Testing, Chongqing University of Science & Technology, Chongqing 401331, China
3School of Nano & Advanced Materials Engineering, Changwon National University, Changwon 51140, Republic of Korea

Correspondence should be addressed to Kejian Li; moc.liamg@nnaijekil

Received 24 July 2017; Revised 8 October 2017; Accepted 24 October 2017; Published 12 December 2017

Academic Editor: Guosong Wu

Copyright © 2017 Kejian Li et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. J. Swaminathan, R. Singh, M. K. Gunjan, and B. Mahato, “Sensitization induced stress corrosion failure of AISI 347 stainless steel fractionator furnace tubes,” Engineering Failure Analysis, vol. 18, no. 8, pp. 2211–2221, 2011. View at Publisher · View at Google Scholar · View at Scopus
  2. A. Momeni and S. M. Abbasi, “Repetitive thermomechanical processing towards ultra-fine grain structure in 301, 304 and 304L stainless steels,” Journal of Materials Science & Technology, vol. 27, pp. 338–343, 2011. View at Publisher · View at Google Scholar
  3. H. Huang, Z. B. W, J. Lu, and K. Lu, “Fatigue behaviors of AISI 316L stainless steel with a gradient nanostructured surface layer,” Acta Materialia, vol. 87, pp. 150–160, 2015. View at Publisher · View at Google Scholar
  4. I. S. Cho, Y. He, K. Li et al., “Very high cycle fatigue behavior of SAE52100 bearing steel by ultrasonic nanocrystalline surface modification,” Journal of Nanoscience and Nanotechnology, vol. 14, no. 11, pp. 8264–8269, 2014. View at Publisher · View at Google Scholar · View at Scopus
  5. J. Hu, Y. N. Shi, X. Sauvage, G. Sha, and K. Lu, “Grain boundary stability governs hardening and softening in extremely fine nanograined metals,” Science, vol. 355, no. 6331, pp. 1292–1296, 2017. View at Publisher · View at Google Scholar · View at Scopus
  6. K. Lu, “Making strong nanomaterials ductile with gradients: microstructures that increase metal crystallite size from nanoscale with surface depth are both strong and ductile,” Science, vol. 345, no. 6203, pp. 1455-1456, 2014. View at Publisher · View at Google Scholar · View at Scopus
  7. X. Li, Y. Wei, L. Lu, K. Lu, and H. Gao, “Dislocation nucleation governed softening and maximum strength in nano-twinned metals,” Nature, vol. 464, no. 7290, pp. 877–880, 2010. View at Publisher · View at Google Scholar · View at Scopus
  8. C. Fang, K. Li, H. Ma et al., “Microstructural evolution of TP347H after post weld heat treatment and aging,” Science of Advanced Materials, vol. 8, no. 12, pp. 2260–2263, 2016. View at Publisher · View at Google Scholar · View at Scopus
  9. Y. Akiniwa, H. Kimura, and T. Sasaki, “Effect of residual stresses on fatigue strength of severely surface deformed steels by shot peening,” Powder Diffraction, vol. 24, no. 1, pp. S37–S40, 2009. View at Publisher · View at Google Scholar · View at Scopus
  10. C. Kuebel, A. Kobler, and H. Hahn, “In-situ Straining Analysis by TEM orientation mapping (EBSD-like TEM) - Direct imaging of deformation processes in nanocrystalline metals,” Microscopy and Microanalysis, vol. 18, pp. 724-725, 2012. View at Google Scholar
  11. H. Hwang and Y. Park, “Effects of heat treatment on the phase ratio and corrosion resistance of duplex stainless steel,” Materials Transactions, vol. 50, pp. 1548–1552, 2009. View at Publisher · View at Google Scholar