Research on the Sparse Representation for Gearbox Compound Fault Features Using Wavelet Bases

Luo, Chunyan; Shen, Changqing; Fan, Wei; Cai, Gaigai; Huang, Weiguo; Zhu, Zhongkui

doi:https://doi.org/10.1155/2015/560171

Shock and Vibration

On this page

Abstract Introduction Conclusions Acknowledgments References Copyright Related Articles

Special Issue

Fault Diagnosis and Prognosis of Critical Components

View this Special Issue

Research Article | Open Access

Volume 2015 | Article ID 560171 | https://doi.org/10.1155/2015/560171

Research on the Sparse Representation for Gearbox Compound Fault Features Using Wavelet Bases

Chunyan Luo,¹Changqing Shen,²Wei Fan,¹Gaigai Cai,¹Weiguo Huang,¹and Zhongkui Zhu¹

Academic Editor: Dong Wang

Received29 Jun 2015

Accepted12 Aug 2015

Published07 Dec 2015

Abstract

The research on gearbox fault diagnosis has been gaining increasing attention in recent years, especially on single fault diagnosis. In engineering practices, there is always more than one fault in the gearbox, which is demonstrated as compound fault. Hence, it is equally important for gearbox compound fault diagnosis. Both bearing and gear faults in the gearbox tend to result in different kinds of transient impulse responses in the captured signal and thus it is necessary to propose a potential approach for compound fault diagnosis. Sparse representation is one of the effective methods for feature extraction from strong background noise. Therefore, sparse representation under wavelet bases for compound fault features extraction is developed in this paper. With the proposed method, the different transient features of both bearing and gear can be separated and extracted. Both the simulated study and the practical application in the gearbox with compound fault verify the effectiveness of the proposed method.

1. Introduction

As a fundamental mechanical component for transmitting power, gearbox has been widely used in modern industry. Because of its complicated structure, hostile working conditions, and other reasons, gearbox is usually easily damaged and breaks down. Therefore, it is of great significance to develop proper condition monitoring and fault diagnosis method for gearbox in order to prevent the unexpected machine fault during operation and even casualties [1].

When a fault is occurring in a bearing or a gear, both of which are vital components for gearbox, periodic transient impulses appear in its generated vibration signals. Researches have shown that the transients in the captured signal always comprise the important information of fault feature from the defective component [2]. Therefore, gearbox fault feature extraction can be transformed into extracting the transients in the generated signal.

During the past two decades, various advanced signal processing methods have been proposed for effective fault feature extraction in rotary machines. Time-frequency analysis [3, 4], whose analysis of a signal is performed in both time and frequency domains, is developed for nonstationary signal processing. As a typical method of time-frequency analysis, Wigner-Ville Distribution (WVD) has proven its effectiveness in mechanical fault diagnosis [5, 6]. Wavelet transforms, which decompose an original signal into different scales with varying frequency bandwidths [7, 8], are also used to extract fault-related information of rotary machines [9, 10]. Empirical mode decomposition (EMD) [11], a self-adaptive signal processing technique, decomposes the nonlinear and nonstationary signal into a set of intrinsic mode functions (IMF). It has also been introduced to fault diagnosis of rotary machines [12, 13].

However, methods mentioned above are mostly used on the occasion that there is single fault in the machinery. A number of engineering practices have shown that there is usually more than one fault in a gearbox, which is demonstrated as compound fault [14]. When different faults exit simultaneously, vibration signal excited by several faults always contains different transient impulse responses, which makes it quite complex and difficult to identify each fault from the observed signal in terms of traditional methods. Hence, some novel techniques for compound fault diagnosis have been developed gradually. The blind source separation (BSS) technique [15] can separate several original signals that cannot be observed directly from the superposed signals and has been used in extracting machinery faults features from different rotary components [16, 17]. However, the analyzed compound signals in BSS are usually derived from different channels through several transducers, which may bring some inconvenience in installing transducers during engineering application. Morphological component analysis (MCA) [18] was also developed for compound signal decomposition based on the morphological diversity of each component [19, 20]. However, MCA requests that the vibrations generated by each faulty component are totally irrelevant, which may lower the separation quality. Additionally, some intelligent methods based on models are proposed in recent years for compound faults signals separation [21, 22], but due to its difficulty in acquiring the appropriate data, these intelligent methods have not been widely promoted.

Meanwhile, there has been a growing interest in the study of sparse representation of signals recently [23, 24]. With an overcomplete dictionary which contains prototype signal-atoms, signals can be described as a sparse linear combination of these atoms [25, 26]. Till now, sparse representation has already been used in single fault feature extraction, and its excellent extraction property has been proven [27, 28]. According to the characteristics of gear fault vibration signal, Cai et al. [27] proposed the sparsity-enabled signal decomposition using tunable -factor wavelet transform and successfully extracted the fault feature of gear. In [28], Fan et al. constructed a sparse dictionary corresponding to the signal characteristic and combined Majorization-Minimization (MM) algorithm to extract the gear transient impulse responses sparsely.

Based on the engineering practical requirement, further research on the gearbox compound fault diagnosis should be conducted. On the basis of failure ratio investigation among the components in gearbox, the main failure components tend to be bearing and gear. However, there are few methods for extracting gearbox compound fault features of both bearing and gear faults. Hence, it is of much importance to pay attention to gearbox compound fault diagnosis when both bearing and gear faults occur. Due to its excellent self-adaptability, concise expression, and other merits, sparse representation is introduced in this paper for separating and extracting the gearbox compound fault features. Once there are both bearing and gear faults in a gearbox, there will always be two different kinds of transient impulse responses in the sampled signal. Considering the diversity in waveforms of each fault, different optimal wavelet bases thus can be constructed by correlation filtering [29, 30]. Then the constrained optimization algorithm with obtained special basis is incorporated to get a series of sparse coefficients which represent the specific fault. After representing the fault in sparse coefficients with the suitable constrained optimization algorithm one by one, the impulse time and the period parameter of each fault in the gearbox can be detected from the sparse coefficients properly.

The rest of this paper is outlined as follows. In Section 2, the basic theoretical background concerning the proposed method is introduced. A simulated study is given to verify the effectiveness of the proposed method in Section 3. In Section 4, the proposed method is applied to the gearbox compound fault features extraction to further verify its effectiveness. At last, Section 5 gives the conclusions.

2. Theoretical Framework

2.1. Sparse Representation Theory

Signal sparse representation is to represent the signal with as fewer nonzero values as possible in an overcomplete dictionary, in order to simplify the procedure of signal processing. The following part gives a concrete description on sparse representation theory.

Assume that a set contains elements and linearly independent vectors with ; thus, the set is an overcomplete dictionary or basis. Each column of the matrix is a signal called an atom. Considering the signal sampled from the transducer contains noise, the observed signal can be modeled aswhere is the observed noisy signal, is the true signal without noise, and is the noise. The true signal can be represented sparsely with the overcomplete basis and also can be described as a linear combination of certain atoms of . Therefore, the representation of can be expressed as , where is the vector of representation coefficients which also represents the transient. The occurrence of an impulse in the cyclic signal generates a value in the sparse coefficient vector accordingly. Therefore, when the cyclic impulses occur in the signal, cyclic values occur in the sparse coefficient vector correspondingly, and other values in the sparse coefficient vector will be zeros theoretically. Thus, the representation coefficient vector has sparsity, and then the cyclic transient components as well as the impulse time of the signal can be extracted from the sparse coefficients. As a result, the estimation modal in (1) turns intowhere is an matrix, with ; is a length- vector. The more similar the basis and the signal are, the sparser the vector will be. Based on the sparse representation theory, to obtain the sparse representation of signal under overcomplete basis , the optimization function can be constructed aswhere is the -norm of vector , counting the nonzero values of vector . It is well known that the problem in (3) of estimating is a nondeterministic polynomial (NP) problem, which is difficult to make out. Usually, problem (3) is transformed intowhere is the -norm of vector , defined as .

2.2. Optimization Algorithm for Sparse Representation

At present, sparse algorithms including greedy pursuit algorithms and convex relaxation algorithms have been proposed to resolve the problem in (4). Greedy algorithms mainly contain Matching Pursuit (MP) algorithm [31] and Orthogonal Matching Pursuit (OMP) [32] which is developed by MP algorithm and so forth. Basis Pursuit (BP) algorithm, as one of the convex relaxation algorithms, is proposed by Chen et al. in [33]. It is different from the greedy methods by replacing the -norm by -norm to transform the combinatorial optimization problem into convex optimization problem. BPD algorithm, developed based on BP algorithm, having the advantage of eliminating noise inference, is introduced to solve the problem in (4):where is the -norm of vector , defined as , and is the regularization parameter. After the minimization of objective function in (5), a sparse representation vector can be obtained. To minimize , an iterative algorithm must be introduced. The traditional gradient descent methods always converge slowly, such as iterative shrinkage/thresholding algorithm (ISTA) [34] and fast IST algorithm (FISTA) [35]. In order to improve the speed of convergence, Afonso et al. proposed a novel technique named the split augmented Lagrangian shrinkage algorithm (SALSA) [36], which is faster than the earlier methods. The algorithm updates the vector during each iteration so as to minimize the objective function until the optimal solution is gained.

Considering the unconstrained optimization problem in which the objective function is the sum of two functions, (5) can be written aswhere , . Then variable splitting is introduced to create a new variable denoted by , to serve as the augment of , under the constraint that . This leads to the constrained problem:which is obviously equivalent to the unconstrained problem in (6). Then, use the following definitions: , , , . With these definitions, (7) can be transformed intoThe augmented Lagrangian function for this problem is defined aswhere is a vector of Lagrange multipliers and is the penalty parameter. The augmented Lagrangian method (ALM) is used to minimize the objective function , and the following results can be obtained:where is the iteration counter. Considering the concrete forms of the function , matrix and the vector , novel results can be written asEquation (11) is a strictly convex quadratic function to be minimized, which leads to the solution directly, and the soft threshold facilitates the minimization of (12), after which the iteration procedure of SALSA can be listed as

By running the iterative numerical algorithm SALSA, the optimal sparse solution can be found eventually. With the sparse solution , which means most elements of the vector are closer to zero, the reconstructed can be represented as . In the sparse vector , there are successive periodic nonzero coefficients which present the transient responses in the original signal. Thus, the fault period can be calculated from the envelope spectrum analysis of the reconstructed signal, after which the fault feature is eventually extracted.

2.3. Selection of the Optimal Wavelet Bases by Correlation Filtering

After choosing SALSA as the sparse optimization algorithm, the selection of wavelet bases turns out to be another key work. In order to represent the original signal as sparse as possible, the basis should be as relevant to the signal as possible. Considering the characteristics of vibration signal of the faulty bearing, the Laplace wavelet, which is in shape similar to the signal transients caused by bearing localized fault, is selected to construct the wavelet basis during the extraction of bearing fault feature. The Laplace wavelet is defined aswhere the parameter vector determines the wavelet properties. These parameters denote frequency , damping ratio , and time index , respectively. The parameter is used to normalize the wavelet function.

The parameters , , and belong to the subsets of , and respectively. With different parameters, the Laplace wavelet dictionary can be constructed as

With the constructed Laplace wavelet basis, correlation filtering is introduced to identify the optimal set of parameters . Correlation is used to determine the similarity between the wavelet basis and the original signal and measured by inner product operation. The correlation function is defined to calculate the correlation degree between the basis and the original signal :where is the angle between and . The smaller the angle is, the more similar the basis and the original signal will be. Therefore, the optimal wavelet atom with optimal parameters can be obtained by maximizing the correlation function at each time value from the constructed Laplace wavelet dictionary. Peaks of for a given time value can be represented asand the time index parameter can be calculated by maximizing the coefficient . With correlation filtering, the optimal parameters can be found effectively; then the optimal wavelet atom with these parameters can be constructed.

Meanwhile, the Morlet wavelet, which is in shape similar to the vibration signal transients caused by gear localized fault, is used to construct the wavelet basis during the extraction of gear fault feature. The Morlet wavelet is defined aswhere the parameter vector also determines the wavelet properties. These parameters denote frequency , damping ratio , and time index , respectively, and the optimal set of the characteristic parameters also can be found by correlation filtering. The parameter is used to normalize the wavelet function.

2.4. Separation and Extraction for Gearbox Compound Fault

However, the sequence of the compound fault features extraction should be determined first. The influence of propagation path of signals in the gearbox is taken into consideration to handle the problem. The vibration signals, generated from the gearbox, always contain not only the normal vibrations but also the fault vibrations. In theory, these signals transmit arbitrarily in the gearbox, but as a whole there is an overall propagation path of signals: gear-spline-shaft-bearing-casing [37]. When there are faults in both gear and bearing, the signal sampled by the sensor always contains different kinds of transient impulse responses. Because the sensor is placed on the casing, which is closer to the bearing according to the propagation path of the fault vibration signal as shown in Figure 1, the energy of bearing fault feature is thus higher than that of gear fault feature in the captured compound signal. As a result, the feature of bearing with higher energy is extracted first in order to reduce the interference during the extraction of gear fault feature.

Since the choice for bases and has been made, by incorporating them into the algorithm SALSA during the extraction procedure of each fault feature, two sparse vectors and can be obtained one by one. That is, due to the characteristics of the vibration signal of the defective bearing, the Laplace wavelet basis, which is matched with the original compound fault signal by correlation filtering, is firstly incorporated into the iterative algorithm SALSA. Then, a sparse vector , which represents the bearing fault feature sparsely, and the reconstructed signal of bearing fault can be obtained. After the sparse representation of bearing fault feature, the amplitude of each transient impulse is represented by the sparse vector . In order to estimate the real amplitude of the bearing fault transients, a constrained optimization strategy is proposed to estimate the amplitude of the single fault component by introducing the parameter . The spectrum of the residual fault signal is denoted by where is the original signal, is the reconstructed signal of bearing, is the peak frequency of , and is a positive parameter. When is minimized eventually subjected to its constraints, it indicates that the bearing fault component in the residual fault signal has been removed to the largest extent. By solving problem in (20), an optimal value is acquired, and the estimated bearing fault signal can be obtained by the function .

Then, after removing the bearing fault signal, the residual signal should only contain gear fault transient responses and underground noise. To extract the fault feature of gear, Morlet wavelet basis, matched with the obtained residual signal by correlation filtering, is incorporated into the iterative algorithm SALSA. After that, the second sparse vector representing the gear transients is generated. Similarly, the reconstructed signal of gear can be gained by . Similar to the bearing fault feature extraction, it is also necessary to estimate the real gear fault signal by solving another constrained optimization problem:where the spectrum of the residual fault signal is denoted by , is the residual signal after removing the bearing fault component, and is the preliminary reconstructed fault signal of gear. After solving problem in (21), another optimal value is acquired naturally. The estimated gear fault signal thus can be obtained by the function .

To summarize, the procedure of the proposed method in this paper to separate and extract gearbox compound fault features using wavelet bases is presented in Figure 2.

3. Simulated Study

To verify the effectiveness of the proposed method, a simulated compound fault signal processing is performed for different features extraction. Considering the characteristics of the compound fault vibration signal in a gearbox, the signal is constructed aswhere is a period cyclic impulse responses signal to simulate the bearing fault in Figure 3(a). The values of parameters are given. The frequency is Hz, the damping ratio is , the time index is s, the cyclic period is s, and the normalized parameter is . is also a period cyclic signal to simulate the vibration signal of faulty gear in Figure 3(b). Concrete values of the parameters are listed: Hz, , s, s, and . The signal is white Gaussian noise, which is weighted by . The sampling frequency is 25.6 KHz and the sampling number is 5000. Figure 3(c) gives the waveforms of the noisy compound signal.

(a)

(b)

(c)

To separate and extract each fault feature from the noisy compound signal, the proposed sparse representation under wavelet bases is applied. According to the procedure in Figure 2, the first step is to obtain the optimal Laplace wavelet basis matched with the original noisy signal by correlation filtering, which is shown in Figure 4(a). Then incorporate the matched Laplace wavelet basis into the iterative processes of the algorithm SALSA, after which the sparse coefficients representing the transient feature of the faulty bearing can be obtained, as shown in Figure 4(b). The reconstructed signal of bearing is shown in Figure 4(c), and Figure 4(d) gives the envelope spectrum analysis of reconstructed signal. In Figure 4(b), there are successive periodic nonzero values in the sparse vector, which represent the bearing fault transient in the original signal. In Figure 4(d), the fault characteristic frequency of bearing is obtained as 141.1 Hz, almost consistent with the theoretical value ( Hz). Figure 4(e) shows the estimated bearing fault signal with .

(a)

(b)

(c)

(d)

(e)

Remove the estimated bearing fault signal from the original noisy compound signal; we can get a residual signal as shown in Figure 5. Similar to the bearing, the first step is to obtain the optimal Morlet wavelet basis matched with the residual signal by correlation filtering, which is illustrated in Figure 6(a). Then, incorporate the Morlet wavelet basis into the iterative processes of SALSA, sparse coefficients representing the gear fault feature can be obtained in Figure 6(b), and Figure 6(c) gives the reconstructed signal of defective gear. The envelope spectrum analysis of the reconstructed signal is given in Figure 6(d), where we can get the fault characteristic frequency as 20.9 Hz, nearly equal to the simulated value ( Hz). At last, Figure 6(e) shows the estimated gear fault signal with .

(a)

(b)

(c)

(d)

(e)

By analyzing the results of the simulated study, we can conclude that there are both bearing and gear faults in the simulated compound fault signal. The effectiveness of the proposed method has been proven preliminarily.

Taking the noise inference into consideration, the noise intensity is increased gradually in order to analyze the robustness of the proposed method. Figures 7–10 show the extraction results when is selected as 0.4, 0.5, and 0.6, respectively. As shown in these figures, bearing and gear faults can still be separated and extracted from the compound signal accurately. Based on these above analyses, it can be concluded that the proposed method has the capability to suppress the noise inference until the noise intensity is increased to a higher value.

(a)

(b)

(c)

(d)

(e)

(a)

(b)

(c)

(d)

(e)

(a)

(b)

(c)

(d)

(e)

4. Application to Gearbox Compound Fault Features Extraction

To further verify the effectiveness of the proposed method in practical engineering application, defective gearbox data is analyzed. The research object is a single stage transmission gearbox in a test-bed, as illustrated in Figure 10. The faulty gear is a helical gear, whose working parameters are listed in Table 1. The bearing model in the experiment is 30625, taper roller bearing, and its geometric parameters are listed in Table 2. Based on the known parameters, the theoretical fault frequency of the bearing outer race can be calculated as 176.18 Hz.

Aimed at getting gearbox compound fault data, a crack width of 0.4 mm is set in the outer race of the bearing using the linear cutting technique to simulate the localized fault of a bearing, and half a tooth is cut in the driving gear by electric sparkle technique to simulate the localized defection of a gear as shown in Figure 11. Additionally, to reduce the influence of propagation path, the sensor is placed on the bearing end cover close to the faulty bearing. During the experiment, the rotating speed of the motor is 1496 r/min, and the sampling frequency is set at 25.6 KHz.

The measured vibration signal with compound fault is shown in Figure 12(a). From Figure 12(a), the characteristics of each fault cannot be identified clearly. Therefore, the proposed method in this paper is employed to extract different transient features from the noisy signal. Figure 12(b) gives its frequency spectrum. Figure 12(c) is the envelope spectrum analysis of the original signal. In Figure 12(c), there exist different frequency components. Thus, the location of the fault cannot be identified exactly in the gearbox.

(a)

(b)

(c)

According to the procedure of the proposed method in this paper, the first step is to obtain the optimal Laplace wavelet basis matched with the original measured signal by correlation filtering. Figure 13(a) gives the result of matched Laplace wavelet basis. Then, the matched Laplace wavelet basis is incorporated into the iterative algorithm SALSA. Figure 13(b) shows the sparse coefficients of bearing. In Figure 13(b), there are successive nonzeros in the sparse vector, which represent the transient of bearing outer race fault. Figure 13(c) is the reconstructed signal of faulty bearing. Figure 13(d) gives the envelope spectrum analysis of the reconstructed signal, where we can conclude that the feature frequency of the bearing outer race is 174.1 Hz, and it is consistent with the theoretical value 176.18 Hz. Hence, it indicates that there exists a localized fault in the outer race of bearing indeed. Finally, Figure 13(e) shows the estimated bearing fault signal with .

(a)

(b)

(c)

(d)

(e)

After removing the estimated bearing fault signal from the original signal, we can obtain the residual signal in Figure 14. Then the next steps of the proposed method are conducted and the extraction results of the defective gear fault feature are shown in Figure 15. Figure 15(a) gives the optimal matched Morlet wavelet basis. Figure 15(b) gives the sparse coefficients. In Figure 15(b), there are successive nonzeros in the sparse vector, which represent the transients of gear fault. Figure 15(c) shows the reconstructed signal of the defective gear. Figure 15(d) is the envelope spectrum analysis of the reconstructed signal, from which the feature frequency can be obtained as 25.6 Hz, nearly consistent with the theoretical value 24.67 Hz. Therefore, it indicates that there is a localized fault in the gear indeed. Finally, Figure 15(e) shows the estimated gear fault signal with .

(a)

(b)

(c)

(d)

(e)

5. Conclusions

This paper proposes a novel method to represent the gearbox compound fault features sparsely using different wavelet bases so as to separate the different faulty components from the compound signal. Based on the sparse representation theory, the proposed method introduces the numerical iterative algorithm SALSA under Laplace wavelet basis and Morlet wavelet basis, respectively, to solve the BPD problem, after which two sparse vectors can be obtained one by one. One vector represents the transient feature of faulty bearing and the other represents the transient feature of defective gear. As a result, the proposed method converts the gearbox compound fault features into a series of sparse coefficients, which facilitates gearbox fault diagnosis. Both the simulated study and the application to the sampled gearbox compound fault data verify that the proposed method can separate and extract the compound fault features of the gearbox effectively.

Conflict of Interests

The authors declare that there is no conflict of interests regarding the publication of this paper.

Acknowledgments

This work was supported by the National Natural Science Foundation of China (no. 51375322 and no. 51405321), the National Natural Science Foundation of Jiangsu Province (no. BK20140339), and the Natural Science Foundation of the Jiangsu Higher Education Institutions of China (no. 4KJB460023). The authors also would like to appreciate three anonymous reviewers for their constructive comments and suggestions for improving this paper.

References

X. Wei and H. Pan, “Review of the gearbox fault diagnosis technology,” Journal of Test and Measurement Technology, vol. 20, no. 4, pp. 368–376, 2006.
View at: Google Scholar
D. Wang, P. W. Tse, and Y. L. Tse, “A morphogram with the optimal selection of parameters used in morphological analysis for enhancing the ability in bearing fault diagnosis,” Measurement Science and Technology, vol. 23, no. 6, Article ID 065001, 2012.
View at: Publisher Site | Google Scholar
S. Wang, X. Chen, G. Cai, B. Chen, X. Li, and Z. He, “Matching demodulation transform and synchrosqueezing in time-frequency analysis,” IEEE Transactions on Signal Processing, vol. 62, no. 1, pp. 69–84, 2014.
View at: Publisher Site | Google Scholar | MathSciNet
L. Xiang, G. Tang, and A. Hu, “Vibration signal's time-frequency analysis and comparison for a rotating machinery,” Journal of Vibration and Shock, vol. 29, no. 2, pp. 42–45, 2010.
View at: Google Scholar
S. Rajagopalan, J. A. Restrepo, J. M. Aller, T. G. Habetler, and R. G. Harley, “Wigner-Ville distributions for detection of rotor faults in brushless DC (BLDC) motors operating under non-stationary conditions,” in Proceedings of the 5th IEEE International Symposium on Diagnostics for Electric Machines, Power Electronics and Drives (SDEMPED '05), pp. 1–7, IEEE, Vienna, Austria, September 2005.
View at: Publisher Site | Google Scholar
M. Amirmazlaghani and H. Amindavar, “Statistical modeling and denoising Wigner-Ville distribution,” Digital Signal Processing, vol. 23, no. 2, pp. 506–513, 2013.
View at: Publisher Site | Google Scholar
R. Yan, R. X. Gao, and X. Chen, “Wavelets for fault diagnosis of rotary machines: a review with applications,” Signal Processing, vol. 96, pp. 1–15, 2014.
View at: Publisher Site | Google Scholar
C. Shen, D. Wang, F. Kong, and P. W. Tse, “Fault diagnosis of rotating machinery based on the statistical parameters of wavelet packet paving and a generic support vector regressive classifier,” Measurement, vol. 46, no. 4, pp. 1551–1564, 2013.
View at: Publisher Site | Google Scholar
D. Wang, C. Shen, and P. W. Tse, “A novel adaptive wavelet stripping algorithm for extracting the transients caused by bearing localized faults,” Journal of Sound and Vibration, vol. 332, no. 25, pp. 6871–6890, 2013.
View at: Publisher Site | Google Scholar
W. J. Wang and P. D. McFadden, “Application of wavelets to gear box vibration signals for fault detection,” Journal of Sound and Vibration, vol. 192, no. 5, pp. 927–939, 1996.
View at: Publisher Site | Google Scholar
N. E. Huang, Z. Shen, S. R. Long et al., “The empirical mode decomposition and the Hilbert spectrum for nonlinear and non-stationary time series analysis,” Proceedings of the Royal Society of London Series A: Mathematical, Physical and Engineering Sciences, vol. 454, no. 1971, pp. 903–995, 1998.
View at: Publisher Site | Google Scholar | MathSciNet
Y. Lei, J. Lin, Z. He, and M. J. Zuo, “A review on empirical mode decomposition in fault diagnosis of rotating machinery,” Mechanical Systems and Signal Processing, vol. 35, no. 1-2, pp. 108–126, 2013.
View at: Publisher Site | Google Scholar
L. Zhao, W. Yu, and R. Yan, “Rolling bearing fault diagnosis based on CEEMD and time series modeling,” Mathematical Problems in Engineering, vol. 2014, Article ID 101867, 13 pages, 2014.
View at: Publisher Site | Google Scholar
A. Ming, F. Chu, and W. Zhang, “Compound fault features separation of rolling element bearing based on the wavelet decomposition and spectrum auto-correlation,” Journal of Mechanical Engineering, vol. 49, no. 3, pp. 80–87, 2013.
View at: Publisher Site | Google Scholar
M. Zibulevsky and B. Pearlmutter, “Blind source separation by sparse decomposition in a signal dictionary,” Neural Computation, vol. 13, no. 4, pp. 863–862, 2001.
View at: Publisher Site | Google Scholar
Z. Li, X. Yan, Z. Tian, C. Yuan, Z. Peng, and L. Li, “Blind vibration component separation and nonlinear feature extraction applied to the nonstationary vibration signals for the gearbox multi-fault diagnosis,” Measurement, vol. 46, no. 1, pp. 259–271, 2013.
View at: Publisher Site | Google Scholar
P. W. Tse, J. Y. Zhang, and X. J. Wang, “Blind source separation and blind equalization algorithms for mechanical signal separation and identification,” Journal of Vibration and Control, vol. 12, no. 4, pp. 395–423, 2006.
View at: Publisher Site | Google Scholar
J. L. Starck, Y. Moudden, J. Bobin, M. Elad, and D. L. Donoho, “Morphological component analysis,” in Wavelets XI, vol. 5914 of Proceedings of SPIE, pp. 1–15, San Diego, Calif, USA, July 2005.
View at: Publisher Site | Google Scholar
J. Yang, H.-Q. Zheng, Z.-Z. Guan, and Y.-G. Wang, “Compound fault diagnosis for gearbox based on kernel morphological component analysis,” Journal of Vibration and Shock, vol. 31, no. 10, pp. 97–101, 2012.
View at: Google Scholar
H. Li, H.-Q. Zheng, and L.-W. Tang, “Bearing multi-fault diagnosis based on improved morphological component analysis,” Journal of Vibration and Shock, vol. 31, no. 12, pp. 135–140, 2012.
View at: Google Scholar
V. Purushotham, S. Narayanan, and S. A. N. Prasad, “Multi-fault diagnosis of rolling bearing elements using wavelet analysis and hidden Markov model based fault recognition,” NDT & E International, vol. 38, no. 8, pp. 654–664, 2005.
View at: Publisher Site | Google Scholar
D. Wang, K. Tsui, P. W. Tse, and M. J. Zuo, “Principal components of superhigh-dimensional statistical features and support vector machine for improving identification accuracies of different gear crack levels under different working conditions,” Shock and Vibration, vol. 2015, Article ID 420168, 14 pages, 2015.
View at: Publisher Site | Google Scholar
I. Selesnick, “Introduction to sparsity in signal processing,” Connexions, 2012, http://cnx.org/contents/79bacf0d-b81d-4253-987a-f017996e4858@3/Introduction-to-Sparsity-in-Si.
View at: Google Scholar
K. Huang and S. Aviyente, “Sparse representation for signal classification,” Advances in Neural Information Processing Systems, vol. 19, pp. 609–616, 2006.
View at: Google Scholar
T. Poggio and F. Girosi, “A sparse representation for function approximation,” Neural Computation, vol. 10, no. 6, pp. 1445–1454, 1998.
View at: Publisher Site | Google Scholar
K. Kreutz-Delgado, J. F. Murray, B. D. Rao, K. Engan, T.-W. Lee, and T. J. Sejnowski, “Dictionary learning algorithms for sparse representation,” Neural Computation, vol. 15, no. 2, pp. 349–396, 2003.
View at: Publisher Site | Google Scholar | Zentralblatt MATH
G. Cai, X. Chen, and Z. He, “Sparsity-enabled signal decomposition using tunable Q-factor wavelet transform for fault feature extraction of gearbox,” Mechanical Systems and Signal Processing, vol. 41, no. 1-2, pp. 34–53, 2013.
View at: Publisher Site | Google Scholar
W. Fan, G. Cai, W. Huang, L. Shang, and Z. Zhu, “Sparse representation of transients based on wavelet basis and majorization-minimization algorithm for machinery fault diagnosis,” Mathematical Problems in Engineering, vol. 2014, Article ID 696051, 11 pages, 2014.
View at: Publisher Site | Google Scholar
S. Wang, J. Xu, and Z. Zhu, “LSM-based transient parameter identification and its application in feature extraction of bearing fault,” Journal of Mechanical Engineering, vol. 48, no. 7, pp. 68–76, 2012.
View at: Publisher Site | Google Scholar
S.-B. Wang, Z.-K. Zhu, and A.-Z. Wang, “Gearbox fault feature detection based on adaptive parameter identification with Morlet wavelet,” in Proceedings of the 8th International Conference on Wavelet Analysis and Pattern Recognition (ICWAPR '10), pp. 409–414, IEEE, Qingdao, China, July 2010.
View at: Publisher Site | Google Scholar
S. G. Mallat and Z. Zhang, “Matching pursuits with time-frequency dictionaries,” IEEE Transactions on Signal Processing, vol. 41, no. 12, pp. 3397–3415, 1993.
View at: Publisher Site | Google Scholar | Zentralblatt MATH
Y. C. Pati, R. Rezaiifar, and P. S. Krishnaprasad, “Orthogonal matching pursuit: recursive function approximation with applications to wavelet decomposition,” in Proceedings of the 27th Asilomar Conference on Signals, Systems & Computers, pp. 40–44, November 1993.
View at: Google Scholar
S. S. Chen, D. L. Donoho, and M. A. Saunders, “Atomic decomposition by basis pursuit,” SIAM Journal on Scientific Computing, vol. 20, no. 1, pp. 33–61, 1998.
View at: Publisher Site | Google Scholar | MathSciNet
I. Daubechies, M. Defrise, and C. De Mol, “An iterative thresholding algorithm for linear inverse problems with a sparsity constraint,” Communications on Pure and Applied Mathematics, vol. 57, no. 11, pp. 1413–1457, 2004.
View at: Publisher Site | Google Scholar | MathSciNet
A. Beck and M. Teboulle, “A fast iterative shrinkage-thresholding algorithm for linear inverse problems,” SIAM Journal on Imaging Sciences, vol. 2, no. 1, pp. 183–202, 2009.
View at: Publisher Site | Google Scholar | Zentralblatt MATH | MathSciNet
M. V. Afonso, J. M. Bioucas-Dias, and M. A. Figueiredo, “Fast image recovery using variable splitting and constrained optimization,” IEEE Transactions on Image Processing, vol. 19, no. 9, pp. 2345–2356, 2010.
View at: Publisher Site | Google Scholar | MathSciNet
W. Li, Vibration source detection system of gearbox based on vibration signal propagation path [Ph.D. thesis], Hangzhou Dianzi University, 2013.

Copyright

Copyright © 2015 Chunyan Luo et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

1022

Downloads

1314

Citations