A Review of Refractometric Sensors Based on Long Period Fibre Gratings

Rego, G.

doi:https://doi.org/10.1155/2013/913418

The Scientific World Journal

On this page

Abstract Introduction Conclusions References Copyright Related Articles

Review Article | Open Access

Volume 2013 | Article ID 913418 | https://doi.org/10.1155/2013/913418

A Review of Refractometric Sensors Based on Long Period Fibre Gratings

G. Rego^1,2

Academic Editor: C. Gao, I. Latka

Received20 Aug 2013

Accepted25 Sept 2013

Published18 Dec 2013

Abstract

In the last decade refractometric sensors have attracted an increasing interest by the scientific community due to their ability to perform ambient monitoring, to assess food quality and safety, and also to the fact that they enable the development of label free sensors in the biomedical area. These advances result, namely, from the use of long period fibre gratings in the turning points and/or with thin films in the transition region that allows resolutions of 10⁻⁶ to changes in the refractive index of the surrounding medium. Resolutions exceeding 10⁻⁸ can also be achieved when long period fibre gratings are combined with evanescent field based devices. This paper reviews the recent path towards the development of ultrahigh sensitive optical fibre refractometric sensors.

1. Introduction

According to recent designations such as smart cities, smart buildings, smart structures, smart grids, or smart clothes, one may conclude that we are living in the “Smart World Era.” Generally speaking, these environments require intelligent devices that incorporate sensors, communication systems, and data processing unities that are able to perform home automation, to monitor structural health of buildings and bridges, to increase the efficiency of energy production, and to manage an electric power grid or to localize patients and monitor their vital parameters. Further developments are expected with the so-called “Internet of Things” in which intelligence is extended to, virtually, all objects [1, 2].

At the same time the world faces the challenge caused by the destructive cycle of environmental pollution, global warming, climate changes, reduction of arable land, and water contamination, added to the demographic pressure and a huge ecological footprint that demands for another planet. Furthermore, the occidental society has a higher life expectancy and diseases, such as, Alzheimer, which are more frequent. Therefore, the future development requires special attention to these issues and the smart technology plays an important role in order to increase the efficiency of food production and to control its safety, to monitor the quality of air and water, and to localize and monitor the health of elder people [3].

In this context, sensors are fundamental devices independently of being the conventional electronic ones (that may constitute a wireless sensor network when, for instance, mobility is required) or optical fibre sensors used in applications where low dimensions, low weight, electromagnetic immunity, and material chemically inert and biocompatible are essential. Since the optical fibre can be, simultaneously, a waveguide and a sensor, it is straightforward to implement optical fibre sensor networks that enable multiplexing of sensors monitoring different physical parameters. As far as the measurement of temperature and strain is concerned, for instance, for health structure monitoring, the fibre Bragg gratings technology has already proved its excellence [4]. Distributed sensing based on the Brillouin effect is paving the way towards the development of temperature sensors, for instance, in the area of energy production. However, in applications such as environmental monitoring or food quality and safety, other approaches are needed. Refractometric sensors based on long period fibre gratings (LPFGs) have shown very promising results in this context [5]. Therefore, this paper reviews the recent achievements related to this technology.

The first section discusses the fabrication of long period fibre gratings in the turning points using the simple, flexible, and low cost electric arc technique. Based on the knowledge of the properties of these gratings a reflection configuration is also presented. The deposition of thin films over the grating, namely, when the film has a particular thickness and refractive index that enables the grating to work in the transition region increasing considerably the sensitivity to changes in the external refractive index, is discussed in Section 2. Section 3 present other configurations for refractometric sensing based on evanescent field that may combine different devices in order to reach ultimate resolutions, for instance, schemes comprising long period fibre gratings and surface plasmon resonances (SPR).

2. Properties of Arc-Induced Gratings

A long period fibre grating is a wavelength selective filter whose transmission spectra exhibit several resonances (Figure 1) resulting from coupling between the core mode and the different copropagating cladding modes at wavelengths that obey the resonance condition [6]: where represent the resonance wavelengths, the grating period, and and the effective refractive index of the core mode and the effective refractive index of the cladding modes, respectively.

Several techniques are available in order to produce LPFGs, among them, those based on UV, CO2, and femtosecond laser radiation, with the later being the most versatile one [6–9]. However, we focused our attention on the electric arc technique for being simple, flexible and having low cost [10]. The main drawback is the fact that so far it was not possible to write LPFGs with grating periods shorter than 200 μm [11]. Arc-induced gratings are fabricated by placing an uncoated fibre, under tension, between the electrodes of a splicing machine. The fibre is then submitted to an arc discharge with an electric current of 7 to 15 mA and a duration ranging from 200 ms up to 2 s. Afterwards the fibre is displaced by the grating period, typically, from 200 μm to 1 mm and the whole process of arc-discharge/fibre displacement is then repeated 20 to 50 times.

The reproducibility of the technique can be compromised by the degradation of the electrodes due to oxidation. However, the control of the position of the fibre in the arc discharge and the monitoring of the discharge parameters and of the ambient conditions would allow the technique to be used for mass production of gratings with precise and reproducible characteristics [12].

Figure 2 shows the setup used to inscribe the gratings where it can also be seen that the arc discharge is directional. It was demonstrated that, in this particular arrangement, the arc possesses a thermal gradient that is responsible for the main formation mechanism of these gratings in standard fibres, that is, microdeformations [12]. For the typical fabrication parameters used the fibre reaches a temperature of the order of 1400°C [13] which softens the fibre under tension and the arc thermal gradient induces the microdeformations responsible for the grating. Arc-induced gratings can stand temperatures as high as 1000°C for several days without significant deterioration in their spectrum [14]. It was also demonstrated that the resonance wavelengths are defined not only by the choice of the grating period but also by the fabrication parameters used [15]. Moreover, the fabrication parameters also modify the sensitivity of the resonances to changes of physical parameters such as temperature and strain. Thus, by changing the fabrication parameters during the inscription of a grating we obtained a set of two neighbour resonances showing different sensitivities that enabled to implement a sensor for the simultaneous measurement of temperature and strain requiring a single optical source [16]. It is interesting to note that in the case of the fibre codoped with B/Ge the main mechanism of grating formation is not microdeformations but a reversible densification of the core that leads to coupling to symmetric cladding modes in opposition to the asymmetric ones due to the former mechanism [17, 18]. However, by a proper choice of the fabrication parameters and by placing the fibre in a region of the arc with lower average temperature and grater thermal gradient (i.e., also an optimum point to increase the reproducibility of the technique) it is possible to fabricate simultaneously two superimposed gratings showing a dual set of resonances resulting from two different mechanisms: microdeformations and densification [19]. The resonances show different sensitivities to changes in physical parameters and the ones due to densification are erased as the temperatures rise towards 1000 °C. The development of sensors based on these properties will be discussed below.

The resonance wavelengths depend on the effective refractive index of the cladding modes which in turn depend on the refractive index of the external medium. Thus, LPFGs are intrinsically sensitive to changes in the surrounding medium and, therefore, can be used as refractive index sensors. Several techniques have been used in order to increase the gratings sensitivity to changes in the external refractive index that depends on the interaction of the cladding modes with the surrounding medium. For that purpose several approaches were implemented: gratings were written in fibres having a cladding refractive index closer to the one of the surrounding medium, written in etched or tapered fibres, by producing microtapered gratings or by bending the grating. In this context, interferometric configurations were also used. The resolutions obtained ranged from to [20–26].

3. LPFGS in the Turning Points

It is well known that the LPFGs sensitivity depends on the order of the cladding modes and reaches its maximum close to the so-called turning points [27]. In these regions the slope of the phase matching curves changes from positive to negative and beyond this turning point, and for each grating period, there are two resonance wavelengths for each cladding mode (Figure 3). This is due to the dependence on wavelength of the core and cladding effective refractive indices. For a particular grating period, the phase matching condition can be satisfied for more than one resonance wavelength (for the same cladding mode) since, as the wavelength increases, the effective refractive index of the cladding mode decreases faster than that of the core [28].

(a)

(b)

In the context of refractometric sensing, the dependence of the resonant wavelengths on changes in the refractive index of the surrounding medium can be understood by the following equations [27]: where , the general sensitivity factor, describes the waveguide dispersion and is expressed by where represents the slope of the dispersion curves. is expressed by and describes the dependence of the waveguide dispersion on the surrounding refractive index (). The term is the th root of the zero-order Bessel function and the other symbols have their common meaning. From (2) and (3) it can be concluded that the sensitivity increases with the slope of the dispersion curves (requires higher order cladding modes and/or working near the turning points). Note that for a particular mode the resonance wavelengths beyond the turning points show higher sensitivities (see also Figure 3). Equation (4) also shows that the sensitivity increases as the refractive index of the surrounding approaches that of the cladding. In this case the evanescent field extends further into the surrounding medium leading to a higher interaction. However, when the surrounding refractive index equals that of the cladding (it becomes an infinite medium), the resonances disappear. For refractive indices above that of the cladding the resonances reappear but at longer wavelengths [29]. In this case, the modes are guided by Fresnel reflection and not by total internal reflection (when , there is no critical angle) and loose part of the energy at each reflection at the interface being called lossy modes. As the refractive index increases the modes become more confined and the dips more pronounced. However, the resonance wavelengths are insensitive to changes in the surrounding refractive index because the phase of the partially reflected field at the surrounding-cladding interface does not change with the external index [30, 31].

In general, grating periods shorter than 200 μm are required in order to have access to this sensitive region (around the turning points), but this possibility was not yet demonstrated for arc-induced gratings. Presently we are developing a new power supply to produce a stable arc with reduced dimensions. At the same time, it is known that during an arc discharge the fibre reaches thermal equilibrium in less than half a second [32] and, therefore, a shorter arc duration will mitigate the effect of thermal diffusion. Thus, the combination of these two factors will allow us to fabricate arc-induced gratings in the turning points. Depending on the choice of the grating period around the turning point, the changes on the surrounding refractive index can be monitored by following either the wavelength shift or the intensity variation [27, 33] (see Figure 4). Recently, two sensors based on LPFGs in the turning points (intensity/wavelength) showed a resolution of [34, 35].

(a)

(b)

In the case of the wavelength measurement a -shifted LPFG in the turning points was used. It should be stressed that a proper choice of the grating period allows some tuning of the sensitivity for a particular refractive index range to be measured (see Figure 5). Further tuning can also be accomplished by etching the fibre cladding [36].

A drawback of using sensors based on LPFGs is the fact that they need access to both ends of the fibre. In a recent publication [37], the authors proposed the inscription of a -shifted LPFG [38, 39] by the deposition of a mirror at the end of the fibre at a distance of to the grating (Figure 6). In this way they implemented a sensor working in a reflection configuration for the simultaneous measurement of temperature and refractive index. The difference in the sensitivity obtained for both resonances is small due to the proximity of the resonance wavelengths. However the sensitivities can be increased considerably if one inscribes simultaneously two gratings, near the turning points, exhibiting a dual set of resonances with different symmetries in the B/Ge-doped fibre (Figure 7) [19]. In this way we end up with a sensor head having the advantage of working in reflection, plus the higher sensitivity of the turning points and the distinct sensitivities of the resonances belonging to two -shifted LPFGs of different symmetries. This configuration enables the simultaneous measurements of different parameters by using either the resonance wavelengths or the resonances of the bandpass filters. This ability is important to overcome the problem of cross-sensitivity to other parameters, such as temperature. Note that the separation between the symmetric and asymmetric resonance wavelengths can be increased by using shorter grating periods. This sensor head is currently under development (at this stage the gratings were not written in the turning points) and the results will be published elsewhere.

(a)

(b)

4. Thin Film-Coated LPFGs

Although the inscription of LPFGs in the turning points increases their sensitivity to changes in the surrounding refractive index, it is known that the sensitivity is higher as the refractive index of the surrounding approaches that of the cladding. This imposes a limitation to work with gases or water solutions. Furthermore, gratings are also insensitive to refractive indices above that of the cladding. Therefore, means to overcome those limitations were required. In 2002, Rees et al. [40] demonstrated that the deposition of a thin film over the grating, with a refractive index exceeding that of the cladding, changes the position of the resonances. As the film thickness increases, the average external refractive index also increases leading to a down shift of the resonances. A point is reached where the resonances disappear. This was attributed to the fact that the average index of the external medium equals that of the cladding. With further deposition the resonances reappear but at a higher wavelength followed by a down shift towards the values obtained for the case of a LPFG surrounded by an infinite medium. The deposition of a thin film over the grating slightly increased the sensitivity to changes in the refractive index of the surrounding medium lower than that of the cladding. On the other hand, it allowed the measurement of refractive index changes of the surrounding medium with a refractive index above that of the cladding [41]. For instance, the deposition of a 110 nm thin film with a refractive index of 1.57 allowed assessing the quality of fried oil with a refractive index of ~1.47 (Figure 8) [42].

Subsequent research [43–46] enabled a deeper interpretation of the transition region, that is, the region where the resonances of LPFGs coated with the Langmuir-Blodgett technique disappear. In fact, with the increase of the film thickness a cladding mode is allowed to be guided in the film leading to a rearrangement of the cladding modes in which a cladding mode order will replace the position of the cladding mode with the precedent order (e.g., LP₀₈ replaces LP₀₇; see Figure 9). This is a fast transition leading to the highest sensitivity.

(a)

(b)

(c)

The higher the film refractive index, the lower the thickness required to reach the transition region (see Figure 10). The thickness also decreases as the surrounding refractive index approaches that of the cladding [46]. Both facts as well as higher cladding modes order lead to faster transitions (higher sensitivity).

(a)

(b)

On the other hand the transition region occurs for lower values of the surrounding refractive index as the film thickness increases. This also contributes to a decrease of the sensitivity [47] (Figure 11). Therefore, a proper choice of the refractive index and thickness of the film would allow the implementation of sensors optimized for refractive indices lower than that of the cladding such as applications in air or water environments.

(a)

(b)

(c)

(d)

However in the optimum point, that is, a particular film thickness, the resonances almost disappear making it impossible to follow the resonance change. The reasons for that disappearing are the film loss and the fact that during the transition the modes also change from HE to EH before replacing the HE mode of lower order [48–52]. Note that for high loss films it is not always the lowest order cladding modes to be guided first by the film (Figure 12). The resonances below the one that is guided by the film behave differently from those above it. Figure 13 shows that, as the film thickness increases, other transitions will occur. Transitions are faster for higher order transitions [50].

(a)

(b)

Therefore care must be taken in order to stop the film deposition before the optimum point and to control the film loss by a proper choice of the deposition technique. In fact it is known that the dip-coating technique leads to films with lower loss but at the same time does not allow a good control of the thickness [5]. Figure 14 shows that, although the coupling strengths decrease in the transition region, the resonances are still visible [47]. Thus, the best option would be a combination of two techniques, first dip-coating to control loss and then electrostatic self-assembly to control the thickness [53].

The deposition of two thin films in which the first layer has a smaller refractive index than the second layer forms a tunnel effect that leads to a more pronounced two step transitions [54]. On the other hand, it is possible to use a first layer to increase the overall sensitivity and a second one being selective to a particular chemical or biologic component [55]. Thin films sensitive to specific components, such as, for pH measurement or for detection of Cl⁻, chloroform, hydrogen, methane, and ethanol, have also been used [44, 56–62]. In this case, the sensitivity of the film increases if its refractive index approaches that of the cladding [56]. Finally, the combination of LPFGs in the turning points with thin films in the transition region led to the implementation of a sensor with a resolution of the order of @1.35 [5]. LPFGs in the turning points coated with thin films have been used for detection of ammonia, E. coli, and glucose [63–65]. In the latter case the properties of the film, such as its permeability to the analyte, were taken into account in order to increase the sensitivity (Figure 15). Thus, instead of a simple adsorption to the surface that mainly increases the film thickness, there is diffusion into the film leading to an overall increase on its refractive index. It is expected that future research on these subjects will contribute to a further increase in the sensitivity of refractometric sensors.

(a)

(b)

5. LPFGs-Assisted SPR

The sensitivity of refractometric sensors depends strongly on the interaction between the evanescent field and the analyte. Therefore, it can be increased by reducing the fibre diameter. Tapering the fibre to dimensions of a few micrometers or even to nanometers scale leads to resolutions of 10⁻⁶–10⁻⁷ RIU [66–68]. The interaction can also be increased by introducing the analyte in the holes of a PCF fibre leading to similar resolutions [69–71]. Another remarkable approach is based on the coupling to whispering gallery modes (WGM) of a resonator [72]. The combination of nanotapers and microresonators led to the detection of a single virus [73].

It is well known that the refractometric sensors based on surface plasmon resonance (SPR) have demonstrated the highest sensitivity, although for bulk configurations where intensity or phase was measured [74–76]. In which concerns optical fibre based SPR, for which miniaturization is possible, the results obtained so far are similar to the ones demonstrated by other configurations based on LPFGs with thin films. The interaction of a mode guided by the fibre and the free electrons of a metallic film, deposited over the cladding, results in coupling to a surface plasmon wave that originates from a resonance dip in the transmission spectrum [77, 78]. For high sensitivity a single mode fibre is tapered in order to allow the interaction of the core mode with the thin film [79]. This approach has an added advantage of allowing the sensor to work in the 1.55 μm wavelength range (Figure 16). Alternatively, under certain constrains (grating period and length), LPFG-assisted SPR can be employed [80–82]. This approach does not compromise the fibre integrity but limits the use of the sensor to the visible or near-infrared range (Figure 17).

When the film consists of metallic nanoparticles, the incident radiation interacts with the conduction electrons confined to the nanoparticles and is absorbed and scattered giving rise to localized SPR (LSPR) [83–85]. The resonance wavelength is strongly dependent on the particles size, shape, composition, and the dielectric properties of the surrounding medium. Although SPR is more sensitive, the response of LSPR sensors is more linear and its sensitivity can be tuned since it depends on the dimensions of the nanoparticles. A thin film surrounded by two media of close refractive index gives rise to the so-called long range SPR (LR-SPR), that is, a strong interaction on both sides of the metallic film that leads to a higher sensitivity (despite the larger FWHM) and low loss (for films with thickness lower than 25 nm) [86, 87]. Moreover, it allows coupling assisted by LPFGs with periods of hundreds of micrometers at a resonance wavelength of 1550 nm [88]. Recently, it was found that the deposition of a high refractive index silicon coating (doped with phosphorus), with 5 to 10 nm thickness, over the metallic layer increases considerably the sensitivity of the SPR sensor besides protecting the silver film from oxidation [89, 90]. Thus SPR with silicon coatings has been applied to the measurement of urea and pH [91, 92]. These innovative configurations involving SPR and LPFGs can be further extended to other devices such as nanotapers and WGM pushing forward the sensors sensitivity [93]. Figure 18 shows the possible inscription of a LPFG to assist coupling to a WGM avoiding the requirement of using small curvature radius that may damage the sensor. Refractive index resolutions exceeding may be achieved by this configuration. Similar results are expected for optical fibre SPR based on phase measurements [94].

6. Conclusions

Sensors and, in particular, refractometric sensors have a key role in this smart era. Long period fibre gratings are intrinsically sensitive to the surrounding refractive index and have already demonstrated their potential for the implementation of this kind of sensors. The fabrication of highly sensitive sensors requires the inscription of LPFGs in the turning points. However, this procedure must be combined with the deposition of thin films over the grating, with the proper refractive index and thickness, in order to optimize the sensitivity to the measurement of refractive indices far from that of the cladding. Further increase in the sensitivity demands for the association of different techniques that lead to a higher interaction of the evanescent field with the parameter to be measured. Therefore, a reduction of the fibre cladding and/or a combination of LPFGs with SPR and/or WGMs may be the path for the development of ultrahigh sensitive refractometric sensors (exceeding resolutions of ). As a final remark, it should be stressed that to make commercial devices available, besides the high resolution and the multiparameter measurement (namely, refractive index and temperature) exhibited by some sensor configurations, minor product engineering is still required in order to prevent cross-sensitivity of the sensor head to other physical parameters, such as strain and bending.

Acknowledgment

The author would like to thank J. L. Santos for his valuable comments.

References

D. Liu and Q. Sun, “Fibre-optic internet of things (FIOTs),” in Proceedings of the 23rd Annual Meeting of the IEEE Photonics Society (PHOTINICS '10), pp. 226–227, Denver, Colo, USA, November 2010.
View at: Publisher Site | Google Scholar
Z. Zhang, Y. Li, H. Gong et al., “Recent progress in distributed optical fiber Raman photon sensors at China Jiliang University,” Photonic Sensors, vol. 2, no. 2, pp. 127–147, 2012.
View at: Publisher Site | Google Scholar
J. Ko, C. Lu, M. B. Srivastava, J. A. Stankovic, A. Terzis, and M. Welsh, “Wireless sensor networks for healthcare,” Proceedings of the IEEE, vol. 98, no. 11, pp. 1947–1960, 2010.
View at: Publisher Site | Google Scholar
J. M. López-Higuera, L. R. Cobo, A. Q. Incera, and A. Cobo, “Fiber optic sensors in structural health monitoring,” Journal of Lightwave Technology, vol. 29, no. 4, pp. 587–608, 2011.
View at: Publisher Site | Google Scholar
P. Pilla, C. Trono, F. Baldini, F. Chiavaioli, M. Giordano, and A. Cusano, “Giant sensitivity of long period gratings in transition mode near the dispersion turning point: an integrated design approach,” Optics Letters, vol. 37, pp. 4152–4154, 2012.
View at: Publisher Site | Google Scholar
A. M. Vengsarkar, P. J. Lemaire, J. B. Judkins, V. Bhatia, T. Erdogan, and J. E. Sipe, “Long-period fiber gratings as band-rejection filters,” Journal of Lightwave Technology, vol. 14, no. 1, pp. 58–64, 1996.
View at: Publisher Site | Google Scholar
Y. J. Rao, T. Zhu, Z. L. Ran, Y. P. Wang, J. Jiang, and A. Z. Hu, “Novel long-period fiber gratings written by high-frequency CO₂ laser pulses and applications in optical fiber communication,” Optics Communications, vol. 229, no. 1–6, pp. 209–221, 2004.
View at: Publisher Site | Google Scholar
T. Allsop, K. Kalli, K. Zhou et al., “Spectral characteristics and thermal evolution of long-period gratings in photonic crystal fibers fabricated with a near-IR radiation femtosecond laser using point-by-point inscription,” Journal of the Optical Society of America B, vol. 28, no. 9, pp. 2105–2114, 2011.
View at: Publisher Site | Google Scholar
S. J. Mihailov, “Fiber bragg grating sensors for harsh environments,” Sensors, vol. 12, no. 2, pp. 1898–1918, 2012.
View at: Publisher Site | Google Scholar
G. Rego, O. Okhotnikov, E. Dianov, and V. Sulimov, “High-temperature stability of long-period fiber gratings produced using an electric arc,” Journal of Lightwave Technology, vol. 19, no. 10, pp. 1574–1579, 2001.
View at: Publisher Site | Google Scholar
M. Smietana, W. J. Bock, P. Mikulic, and J. Chen, “Increasing sensitivity of arc-induced long-period gratings-pushing the fabrication technique toward its limits,” Measurement Science and Technology, vol. 22, no. 1, Article ID 015201, 2011.
View at: Publisher Site | Google Scholar
O. V. Ivanov and G. Rego, “Origin of coupling to antisymmetric modes in arc-induced long-period fiber gratings,” Optics Express, vol. 15, no. 21, pp. 13936–13941, 2007.
View at: Publisher Site | Google Scholar
G. Rego, L. Santos, B. Schroder, P. Marques, J. Santos, and H. Salgado, “In situ temperature measurement an optical fiber submitted to electric arc discharges,” IEEE Photonics Technology Letters, vol. 16, no. 9, pp. 2111–2113, 2004.
View at: Publisher Site | Google Scholar
G. Rego, P. Caldas, O. Ivanov, and J. L. Santos, “Investigation of the long-term stability of arc-induced gratings heat treated at high temperatures,” Optics Communications, vol. 284, no. 1, pp. 169–171, 2011.
View at: Publisher Site | Google Scholar
G. Rego, P. V. S. Marques, J. L. Santos, and H. M. Salgado, “Arc-induced long-period gratings,” Fiber and Integrated Optics, vol. 24, no. 3-4, pp. 245–259, 2005.
View at: Publisher Site | Google Scholar
G. Rego, R. Falate, O. Ivanov, and J. L. Santos, “Simultaneous temperature and strain measurements performed by a step-changed arc-induced long-period fiber grating,” Applied Optics, vol. 46, no. 9, pp. 1392–1396, 2007.
View at: Publisher Site | Google Scholar
C. Rego, O. Ivanov, and P. V. S. Marques, “Demonstration of coupling to symmetric and antisymmetric cladding modes in arc-induced long-period fiber gratings,” Optics Express, vol. 14, no. 21, pp. 9594–9599, 2006.
View at: Publisher Site | Google Scholar
V. Grubsky and J. Feinberg, “Rewritable densification gratings in boron-doped fibers,” Optics Letters, vol. 30, no. 11, pp. 1279–1281, 2005.
View at: Publisher Site | Google Scholar
G. Rego and O. V. Ivanov, “Two types of resonances in long-period gratings induced by arc discharges in boron/germanium co-doped fibers,” Optics Letters, vol. 32, no. 20, pp. 2984–2986, 2007.
View at: Publisher Site | Google Scholar
G. M. Rego, J. L. Santos, and H. M. Salgado, “Refractive index measurement with long-period gratings arc-induced in pure-silica-core fibres,” Optics Communications, vol. 259, no. 2, pp. 598–602, 2006.
View at: Publisher Site | Google Scholar
H. Dobb, K. Kalli, and D. J. Webb, “Measured sensitivity of arc-induced long-period grating sensors in photonic crystal fibre,” Optics Communications, vol. 260, no. 1, pp. 184–191, 2006.
View at: Publisher Site | Google Scholar
H. Tsuda and K. Urabe, “Characterization of long-period Ggrating refractive index sensors and their applications,” Sensors, vol. 9, pp. 4559–4571, 2009.
View at: Publisher Site | Google Scholar
A. Lim, W. B. Ji, and S. C. Tjin, “Improved refractive index sensitivity utilizing long-period gratings with periodic corrugations on cladding,” Sensors, vol. 2012, Article ID 483471, 5 pages, 2012.
View at: Publisher Site | Google Scholar
T. Allsop, F. Floreani, K. Jedrzejewski et al., “Refractive index sensing with long-period grating fabricated in biconical tapered fibre,” Electronics Letters, vol. 41, no. 8, pp. 471–472, 2005.
View at: Publisher Site | Google Scholar
P. Caldas, P. A. S. Jorge, F. M. Araújo et al., “Fiber modal Michelson interferometers with coherence addressing and heterodyne interrogation,” Optical Engineering, vol. 47, no. 4, Article ID 044401, 2008.
View at: Publisher Site | Google Scholar
P. Caldas, P. A. S. Jorge, F. M. Araújo, L. A. Ferreira, G. Rego, and J. L. Santos, “Geometrical effects on the refractive index sensitivity of Mach-Zehnder fibre modal interferometers based on long-period gratings,” Measurement Science and Technology, vol. 20, no. 7, Article ID 075201, 2009.
View at: Publisher Site | Google Scholar
X. Shu, L. Zhang, and I. Bennion, “Sensitivity characteristics of long-period fiber gratings,” Journal of Lightwave Technology, vol. 20, no. 2, pp. 255–266, 2002.
View at: Publisher Site | Google Scholar
V. Grubsky and J. Feinberg, “Long-period fiber gratings with variable coupling for real-time sensing applications,” Optics Letters, vol. 25, no. 4, pp. 203–205, 2000.
View at: Publisher Site | Google Scholar
D. B. Stegall and T. Erdogan, “Leaky cladding mode propagation in long-period fiber grating devices,” IEEE Photonics Technology Letters, vol. 11, no. 3, pp. 343–345, 1999.
View at: Publisher Site | Google Scholar
Y. Koyamada, “Numerical analysis of core-mode to radiation-mode coupling in long-period fiber gratings,” IEEE Photonics Technology Letters, vol. 13, no. 4, pp. 308–310, 2001.
View at: Publisher Site | Google Scholar
R. Hou, Z. Ghassemlooy, A. Hassan, C. Lu, and K. P. Dowker, “Modelling of long-period fibre grating response to refractive index higher than that of cladding,” Measurement Science and Technology, vol. 12, no. 10, pp. 1709–1713, 2001.
View at: Publisher Site | Google Scholar
G. Rego, L. M. N. B. F. Santos, and B. Schröder, “Estimation of the fiber temperature during an arc-discharge,” Microwave and Optical Technology Letters, vol. 50, no. 8, pp. 2020–2025, 2008.
View at: Publisher Site | Google Scholar
X. Lan, Q. Han, J. Huang et al., “High order mode long-period fiber grating refractive index sensor based on intensity measurement,” in Optical Components and Materials IX, vol. 8257 of Proceedings of SPIE, pp. 1–7, San Francisco, Calif, USA, January 2012.
View at: Publisher Site | Google Scholar
X. Lan, Q. Han, J. Huang et al., “Turn-around point long-period fiber grating fabricated by CO₂ laser for refractive index sensing,” Sensors and Actuators B, vol. 177, pp. 1149–1155, 2013.
View at: Publisher Site | Google Scholar
R. Garg, S. M. Tripathi, K. Thyagarajan, and W. J. Bock, “Long period fiber grating based temperature-compensated high performance sensor for bio-chemical sensing applications,” Sensors and Actuators B, vol. 176, pp. 1121–1127, 2013.
View at: Publisher Site | Google Scholar
X. Chen, K. Zhou, L. Zhang, and I. Bennion, “Dual-peak long-period fiber gratings with enhanced refractive index sensitivity by finely tailored mode dispersion that uses the light cladding etching technique,” Applied Optics, vol. 46, no. 4, pp. 451–455, 2007.
View at: Publisher Site | Google Scholar
J. Huang, X. Lan, A. Kaur, H. Wang, L. Yuan, and H. Xiao, “Reflection-based phase-shifted long period fiber grating for simultaneous measurement of temperature and refractive index,” Optical Engineering, vol. 52, Article ID 014404, 4 pages, 2013.
View at: Publisher Site | Google Scholar
H. Ke, K. S. Chiang, and J. H. Peng, “Analysis of phase-shifted long-period fiber gratings,” IEEE Photonics Technology Letters, vol. 10, no. 11, pp. 1596–1598, 1998.
View at: Publisher Site | Google Scholar
G. Humbert and A. Malki, “High performance bandpass filters based on electric arc-induced π-shifted long-period fibre gratings,” Electronics Letters, vol. 39, no. 21, pp. 1506–1507, 2003.
View at: Publisher Site | Google Scholar
N. D. Rees, S. W. James, R. P. Tatam, and G. J. Ashwell, “Optical fiber long-period gratings with Langmuir-Blodgett thin-film overlays,” Optics Letters, vol. 27, no. 9, pp. 686–688, 2002.
View at: Publisher Site | Google Scholar
I. M. Ishaq, A. Quintela, S. W. James, G. J. Ashwell, J. M. Lopez-Higuera, and R. P. Tatam, “Modification of the refractive index response of long period gratings using thin film overlays,” Sensors and Actuators B, vol. 107, no. 2, pp. 738–741, 2005.
View at: Publisher Site | Google Scholar
E. Simões, I. Abe, J. Oliveira, O. Frazão, P. Caldas, and J. L. Pinto, “Characterization of optical fiber long period grating refractometer with nanocoating,” Sensors and Actuators B, vol. 153, no. 2, pp. 335–339, 2011.
View at: Publisher Site | Google Scholar
J. Yang, L. Yang, C.-Q. Xu, and Y. Li, “Optimization of cladding-structure-modified long-period-grating refractive-index sensors,” Journal of Lightwave Technology, vol. 25, no. 1, pp. 372–380, 2007.
View at: Publisher Site | Google Scholar
A. Cusano, A. Iadicicco, P. Pilla et al., “Coated long-period fiber gratings as high-sensitivity optochemical sensors,” Journal of Lightwave Technology, vol. 24, no. 4, pp. 1776–1786, 2006.
View at: Publisher Site | Google Scholar
S. W. James, C. S. Cheung, and R. P. Tatam, “Experimental observations on the response of 1st and 2nd order fibre optic long period grating coupling bands to the deposition of nanostructured coatings,” Optics Express, vol. 15, no. 20, pp. 13096–13107, 2007.
View at: Publisher Site | Google Scholar
I. D. Villar, I. R. Matías, F. J. Arregui, and P. Lalanne, “Optimization of sensitivity in long period fiber gratings with overlay deposition,” Optics Express, vol. 13, no. 1, pp. 56–69, 2005.
View at: Publisher Site | Google Scholar
A. Cusano, A. Iadicicco, P. Pilla et al., “Mode transition in high refractive index coated long period gratings,” Optics Express, vol. 14, no. 1, pp. 19–34, 2006.
View at: Publisher Site | Google Scholar
I. D. Villar, I. R. Matias, and F. J. Arregui, “Influence on cladding mode distribution of overlay deposition on long-period fiber gratings,” Journal of the Optical Society of America A, vol. 23, no. 3, pp. 651–658, 2006.
View at: Publisher Site | Google Scholar
I. D. Villar, I. R. Matias, and F. J. Arregui, “Influence on cladding mode distribution of overlay deposition on long-period fiber gratings: errata,” Journal of the Optical Society of America A, vol. 23, no. 11, Article ID 2969, 2006.
View at: Publisher Site | Google Scholar
I. D. Villar, J. M. Corres, M. Achaerandio, F. J. Arregui, and I. R. Matias, “Spectral evolution with incremental nanocoating of long period fiber gratings,” Optics Express, vol. 14, no. 25, pp. 11972–11981, 2006.
View at: Publisher Site | Google Scholar
I. D. Villar, M. Achaerandio, I. R. Matías, and F. J. Arregui, “Deposition of overlays by electrostatic self-assembly in long-period fiber gratings,” Optics Letters, vol. 30, no. 7, pp. 720–722, 2005.
View at: Publisher Site | Google Scholar
I. D. Villar, I. R. Matias, F. J. Arregui, and M. Achaerandio, “Nanodeposition of materials with complex refractive index in long-period fiber gratings,” Journal of Lightwave Technology, vol. 23, no. 12, pp. 4192–4199, 2005.
View at: Publisher Site | Google Scholar
Z. Wang, J. R. Heflin, R. H. Stolen, and S. Ramachandran, “Highly sensitive optical response of optical fiber long period gratings to nanometer-thick ionic self-assembled multilayers,” Applied Physics Letters, vol. 86, no. 22, Article ID 223104, 3 pages, 2005.
View at: Publisher Site | Google Scholar
I. D. Villar, I. R. Matías, and F. J. Arregui, “Deposition of coatings on long-period fiber gratings: tunnel effect analogy,” Optical and Quantum Electronics, vol. 38, no. 8, pp. 655–665, 2006.
View at: Publisher Site | Google Scholar
I. D. Villar, I. R. Matias, and F. J. Arregui, “Enhancement of sensitivity in long-period fiber gratings with deposition of low-refractive-index materials,” Optics Letters, vol. 30, no. 18, pp. 2363–2365, 2005.
View at: Publisher Site | Google Scholar
I. D. Villar, I. R. Matias, and F. J. Arregui, “Long-period fiber gratings with overlay of variable refractive index,” IEEE Photonics Technology Letters, vol. 17, no. 9, pp. 1893–1895, 2005.
View at: Publisher Site | Google Scholar
J.-L. Tang and J.-N. Wang, “Measurement of chloride-ion concentration with long-period grating technology,” Smart Materials and Structures, vol. 16, no. 3, pp. 665–672, 2007.
View at: Publisher Site | Google Scholar
J. M. Corres, I. R. Matias, I. D. Villar, and F. J. Arregui, “Design of pH sensors in long-period fiber gratings using polymeric nanocoatings,” IEEE Sensors Journal, vol. 38, pp. 455–463, 2007.
View at: Google Scholar
R. M. Carter, R. R. J. Maier, P. Biswas et al., “Increased sensitivity of long period grating hydrogen sensors through coupling to higher order cladding modes,” in 22nd International Conference on Optical Fiber Sensors, vol. 8421 of Proceedings of SPIE, pp. 1–4, Beijing, China, October 2012.
View at: Publisher Site | Google Scholar
X. T. Wei, T. Wei, H. Xiao, and Y. S. Lin, “Terbium doped strontium cerate enabled long period fiber gratings for high temperature sensing of hydrogen,” Sensors and Actuators B, vol. 152, no. 2, pp. 214–219, 2011.
View at: Publisher Site | Google Scholar
M. Konstantaki, A. Klini, D. Anglos, and S. Pissadakis, “An ethanol vapor detection probe based on a ZnO nanorod coated optical fiber long period grating,” Optics Express, vol. 20, no. 8, pp. 8472–8484, 2012.
View at: Publisher Site | Google Scholar
G. Zhu, X. Li, C. Tao, J. Huang, and J. Yang, “Optical fiber methane sensor based on SAN film containing cryptophane-E-(OEt)₆,” Chinese Optics Letters, vol. 10, no. 10, Article ID 100601, 2012.
View at: Google Scholar
S. Korposh, R. Selyanchyn, W. Yasukochi, S. W. Lee, S. W. James, and R. P. Tatam, “Optical fibre long period grating with a nanoporous coating formed from silica nanoparticles for ammonia sensing in water,” Materials Chemistry and Physics, vol. 133, no. 2-3, pp. 784–792, 2012.
View at: Publisher Site | Google Scholar
S. M. Tripathi, W. J. Bock, P. Mikulic et al., “Long period grating based biosensor for the detection of escherichia coli bacteria,” Biosensors and Bioelectronics, vol. 35, no. 1, pp. 308–312, 2012.
View at: Publisher Site | Google Scholar
R. Z. Yang, W. F. Dong, X. Meng et al., “Nanoporous TiO₂-polyion thin-film-coated long period grating sensors for the direct measurement of low-molecular-weight analytes,” Langmuir, vol. 28, pp. 8814–8821, 2012.
View at: Publisher Site | Google Scholar
M. I. Zibaii, O. Frazão, H. Latifi, and P. A. S. Jorge, “Controlling the sensitivity of refractive index measurement using a tapered fiber loop mirror,” IEEE Photonics Technology Letters, vol. 23, no. 17, pp. 1219–1221, 2011.
View at: Publisher Site | Google Scholar
C. Li, S.-J. Qiu, Y. Chen, F. Xu, and Y.-Q. Lu, “Ultra-sensitive refractive index sensor with slightly tapered photonic crystal fiber,” IEEE Photonics Technology Letters, vol. 24, no. 19, pp. 1771–1773, 2012.
View at: Publisher Site | Google Scholar
G. Brambilla, “Optical fibre nanotaper sensors,” Optical Fiber Technology, vol. 16, no. 6, pp. 331–342, 2010.
View at: Publisher Site | Google Scholar
D. K. C. Wu, B. T. Kuhlmey, and B. J. Eggleton, “Ultrasensitive photonic crystal fiber refractive index sensor,” Optics Letters, vol. 34, no. 3, pp. 322–324, 2009.
View at: Publisher Site | Google Scholar
Z. He, Y. Zhu, and H. Du, “Long-period gratings inscribed in air- and water-filled photonic crystal fiber for refractometric sensing of aqueous solution,” Applied Physics Letters, vol. 92, no. 4, Article ID 044105, 3 pages, 2008.
View at: Publisher Site | Google Scholar
J. Kanka, “Long-period gratings in photonic crystal fibers operating near the phase-matching turning point for evanescent chemical and biochemical sensing,” in Fiber Optic Sensors and Applications, vol. 8370 of Proceedings of SPIE, pp. 1–11, Bellingham, Wash, USA, 2012.
View at: Publisher Site | Google Scholar
N. M. Hanumegowda, C. J. Stica, B. C. Patel, I. White, and X. Fan, “Refractometric sensors based on microsphere resonators,” Applied Physics Letters, vol. 87, no. 20, Article ID 201107, 3 pages, 2005.
View at: Publisher Site | Google Scholar
F. Vollmer, S. Arnold, and D. Keng, “Single virus detection from the reactive shift of a whispering-gallery mode,” Proceedings of the National Academy of Sciences of the United States of America, vol. 105, no. 52, pp. 20701–20704, 2008.
View at: Publisher Site | Google Scholar
S. Roh, T. Chung, and B. Lee, “Overview of the characteristics of micro- and nano-structured surface plasmon resonance sensors,” Sensors, vol. 11, no. 2, pp. 1565–1588, 2011.
View at: Publisher Site | Google Scholar
S. Zeng, X. Yu, W.-C. Law et al., “Size dependence of Au NP-enhanced surface plasmon resonance based on differential phase measurement,” Sensors and Actuators B, vol. 176, pp. 1128–1133, 2013.
View at: Publisher Site | Google Scholar
Y. H. Huang, H. P. Ho, S. Y. Wu, and S. K. Kong, “Detecting phase shifts in surface plasmon resonance: a review,” Advances in Optical Technologies, vol. 2012, Article ID 471957, 12 pages, 2012.
View at: Publisher Site | Google Scholar
B. Lee, S. Roh, and J. Park, “Current status of micro- and nano-structured optical fiber sensors,” Optical Fiber Technology, vol. 15, no. 3, pp. 209–221, 2009.
View at: Publisher Site | Google Scholar
B. D. Gupta and R. K. Verma, “Surface plasmon resonance-based fiber optic sensors: principle, probe designs, and some applications,” Journal of Sensors, vol. 2009, Article ID 979761, 12 pages, 2009.
View at: Publisher Site | Google Scholar
N. Díaz-Herrera, A. González-Cano, D. Viegas, J. L. Santos, and M. C. Navarrete, “Refractive index sensing of aqueous media based on plasmonic resonance in tapered optical fibres operating in the 1.5 μm region,” Sensors and Actuators B, vol. 146, no. 1, pp. 195–198, 2010.
View at: Publisher Site | Google Scholar
Y.-J. He, Y.-L. Lo, and J.-F. Huang, “Optical-fiber surface-plasmon-resonance sensor employing long-period fiber gratings in multiplexing,” Journal of the Optical Society of America B, vol. 23, no. 5, pp. 801–811, 2006.
View at: Publisher Site | Google Scholar
Y. C. Lu, W.-P. Huang, and S.-S. Jian, “Influence of mode loss on the feasibility of grating-assisted optical fiber surface plasmon resonance refractive index sensors,” Journal of Lightwave Technology, vol. 27, no. 21, pp. 4804–4808, 2009.
View at: Publisher Site | Google Scholar
T. Schuster, R. Herschel, N. Neumann, and C. G. Schaffer, “Miniaturized long-period fiber grating assisted surface plasmon resonance sensor,” Journal of Lightwave Technology, vol. 30, no. 8, Article ID 6007032, pp. 1003–1008, 2012.
View at: Publisher Site | Google Scholar
K. A. Willets and R. P. Van Duyne, “Localized surface plasmon resonance spectroscopy and sensing,” Annual Review of Physical Chemistry, vol. 58, pp. 267–297, 2007.
View at: Publisher Site | Google Scholar
H.-Y. Lin, C.-H. Huang, G.-L. Cheng, N.-K. Chen, and H.-C. Chui, “Tapered optical fiber sensor based on localized surface plasmon resonance,” Optics Express, vol. 20, no. 19, pp. 21693–21701, 2012.
View at: Publisher Site | Google Scholar
J. Cao, E. K. Galbraith, T. Sun, and K. T. V. Grattan, “Cross-comparison of surface plasmon resonance-based optical fiber sensors with different coating structures,” IEEE Sensors Council, vol. 12, no. 7, pp. 2355–2361, 2012.
View at: Publisher Site | Google Scholar
R. Rajan, A. K. Sharma, and B. D. Gupta, “Fibre optic sensor based on long-range surface plasmon resonance: a theoretical analysis,” Journal of Optics A, vol. 9, no. 7, pp. 682–687, 2007.
View at: Publisher Site | Google Scholar
M. Vala, S. Etheridge, J. A. Roach, and J. Homola, “Long-range surface plasmons for sensitive detection of bacterial analytes,” Sensors and Actuators B, vol. 139, no. 1, pp. 59–63, 2009.
View at: Publisher Site | Google Scholar
Q. Liu and K. S. Chiang, “Refractive-index sensor based on long-range surface plasmon mode excitation with long-period waveguide grating,” Optics Express, vol. 17, no. 10, pp. 7933–7942, 2009.
View at: Publisher Site | Google Scholar
P. Bhatia and B. D. Gupta, “Surface-plasmon-resonance-based fiber-optic refractive index sensor: sensitivity enhancement,” Applied Optics, vol. 50, no. 14, pp. 2032–2036, 2011.
View at: Publisher Site | Google Scholar
P. Bhatia and B. D. Gupta, “Surface plasmon resonance based fiber optic refractive index sensor utilizing silicon layer: effect of doping,” Optics Communications, vol. 286, pp. 171–175, 2013.
View at: Publisher Site | Google Scholar
P. Bhatia and B. D. Gupta, “Fabrication and characterization of a surface plasmon resonance based fiber optic urea sensor for biomedical applications,” Sensors and Actuators B, vol. 161, no. 1, pp. 434–438, 2012.
View at: Publisher Site | Google Scholar
S. Singh and B. D. Gupta, “Fabrication and characterization of a highly sensitive surface plasmon resonance based fiber optic pH sensor utilizing high index layer and smart hydrogel,” Sensors and Actuators B, vol. 173, pp. 268–273, 2012.
View at: Publisher Site | Google Scholar
Y. N. Kulchin, O. B. Vitrik, A. V. Dyshlyuk, and Z. Zhou, “Novel fiber optic refractometric method for liquid and gaseous media,” Pacific Science Review, vol. 14, pp. 23–27, 2012.
View at: Google Scholar
H. Moayyed, I. T. Leite, L. Coelho, J. L. Santos, and D. Viegas, “Analysis of phase interrogation in SPR-based sensing supported by tapered optical fibres,” in 5th European Workshop on Optical Fibre Sensors (EWOFS '13), vol. 8794 of Proceedings of SPIE, pp. 1–5, Krakow, Poland, 2013.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2013 G. Rego. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

2976

Downloads

1785

Citations