Enhanced Performance by Time-Frequency-Phase Feature for EEG-Based BCI Systems

Xu, Baolei; Fu, Yunfa; Shi, Gang; Yin, Xuxian; Wang, Zhidong; Li, Hongyi; Jiang, Changhao

doi:https://doi.org/10.1155/2014/420561

The Scientific World Journal

On this page

Abstract Introduction Results Conclusions Acknowledgments References Copyright Related Articles

Special Issue

Novel Computational Tools in Biosignal Processing

View this Special Issue

Research Article | Open Access

Volume 2014 | Article ID 420561 | https://doi.org/10.1155/2014/420561

Enhanced Performance by Time-Frequency-Phase Feature for EEG-Based BCI Systems

Baolei Xu,^1,2Yunfa Fu,³Gang Shi,¹Xuxian Yin,^1,2Zhidong Wang,^1,4Hongyi Li,^1,5and Changhao Jiang⁶

Academic Editor: Hak-Keung Lam

Received29 Mar 2014

Revised18 May 2014

Accepted02 Jun 2014

Published17 Jun 2014

Abstract

We introduce a new motor parameter imagery paradigm using clench speed and clench force motor imagery. The time-frequency-phase features are extracted from mu rhythm and beta rhythms, and the features are optimized using three process methods: no-scaled feature using “MIFS” feature selection criterion, scaled feature using “MIFS” feature selection criterion, and scaled feature using “mRMR” feature selection criterion. Support vector machines (SVMs) and extreme learning machines (ELMs) are compared for classification between clench speed and clench force motor imagery using the optimized feature. Our results show that no significant difference in the classification rate between SVMs and ELMs is found. The scaled feature combinations can get higher classification accuracy than the no-scaled feature combinations at significant level of 0.01, and the “mRMR” feature selection criterion can get higher classification rate than the “MIFS” feature selection criterion at significant level of 0.01. The time-frequency-phase feature can improve the classification rate by about 20% more than the time-frequency feature, and the best classification rate between clench speed motor imagery and clench force motor imagery is 92%. In conclusion, the motor parameter imagery paradigm has the potential to increase the direct control commands for BCI control and the time-frequency-phase feature has the ability to improve BCI classification accuracy.

1. Introduction

Brain computer interface (BCI) is an emerging technology in the last decades due to its ability to enable people to control devices using thought directly, such as computer cursors, robotic limbs, and prosthetic devices [1–3]. Furthermore, researchers have shown that the brain-to-brain interface (BBI) makes it possible for a human volunteer to control a rat’s tail movement according to his/her intention [4].

Many cognitive tasks can modulate brain activities, such as motor imagery, mental calculation, and mental singing [5]. Brain activities caused by external stimulations can also be used for BCI, including steady state visual evoked potentials (SSVEP) [6] and P300 [7]. Among these approaches, motor imagery is widely used due to its convenience and no external stimulations [8]. Studies have shown that motor imagery presents similar brain activities as real movement [9].

The modulated brain signals for BCI control can be acquired by both invasive and noninvasive methods [10]. The mostly used noninvasive brain signal is electroencephalography (EEG) due to its high sampling frequency and low cost. The functional near-infrared spectroscopy (fNIRS) is another noninvasive approach to acquire cognitive related brain signals [11]. Also, EEG can be acquired with fNIRS simultaneously to obtain enhanced performance because the two approaches acquire cognitive related brain signals through both electrophysiology and hemodynamic aspect [12].

Before being used to control a device, the brain signals must be decoded first [13, 14]. Most researchers use time, spatial, and frequency features for mental decoding [15–19], but little attention is focused on phase feature. Lachaux et al. researched phase synchrony in brain signals using a statistical measure of phase locking value (PLV) for the first time in 1999 [20]. Gysels and Celka investigated phase synchronization for recognition of mental tasks for BCI in 2004, and their results showed that phase feature is useful for spontaneous EEG classification during mental tasks [21]. Li and Zhang compared PLV with phase interval value (PIV) for classification of motor imagery for BCI applications in 2009 and found that PIV performed better than PLV [22]. Some researchers also apply empirical mode decomposition (EMD) and multivariate extensions of empirical mode decomposition (MEMD) to obtain phase information for BCI and get good results [23]. However, MEMD is time consuming in situations of large channel number and high sampling frequency.

In this paper, we investigate the classification accuracy of different combinations of time-frequency feature and time-frequency-phase feature for motor parameter imagery classification using support vector machines (SVMs) and extreme learning machines (ELMs). Two feature selection criteria are also compared in the paper: the mutual information feature selection (MIFS) criterion and the max-relevance min-redundancy (mRMR) criterion. The Hilbert transform is applied on the mu and beta band EEG signal to get instantaneous phase (IP), as well as instantaneous amplitude (IA) and instantaneous frequency (IF). The band power (BP) feature is compared with these three features and their combinations. Our results show that IP performs best at a classification accuracy of 0.83 when used independently among these four feature types. The classification rate can be improved to 0.92 when the four feature types are used simultaneously. The performances of SVMs and ELMs are similar to each other, and the “mRMR” feature selection criterion performs better than the “MIFS” criterion.

The paper is constructed as follows. In Section 2, we will describe the experiment design in this research. Then, the data analysis methods are presented in Section 3. The results of data analysis are presented in Section 4. Finally, we will discuss the results of this research and make some conclusions in Section 5.

2. Experiment Design

2.1. Experiment Paradigm

Traditional BCI paradigms use motor imagery of different limbs to modulate brain signals and can generally obtain at most 4 or 5 direct control commands [24, 25]. In our research, we adopt the motor parameters imagery paradigm (Figure 1). Three levels of clench speed motor imagery of the right hand and three levels of clench force motor imagery of the right hand are used in the experiment. Subjects exercise right hand clench movement at the speeds of 0.5 Hz, 1 Hz, and 2 Hz according to a metronome. The maximum clench force (MF) of every subject is measured, and then subjects practice to clench their right hand at the levels of 20%, 50%, and 80% MF. During the experiment, subjects are required to recall the feeling of real movements. In this paper, we only investigate the possibility of discrimination of clench speed motor imagery from clench force motor imagery. The reason for using three levels for clench speed and clench force motor imagery is to eliminate the effects of different task intensities. The advantage of our paradigm is the potential ability to provide more direct control commands for BCI applications.

We acquired EEG and fNIRS signals simultaneously. The analysis results of fNIRS signal have been presented in paper [26], and, in this paper, we only analyze the EEG signals. The analysis of enhanced BCI performance of EEG-fNIRS combined feature will be discussed in the future.

Taken into the consideration of time lag in fNIRS response to motor imagery [27], the duration of a single trial is much longer than traditional EEG paradigms. In our experiment, a single trial comprises four parts: 10-second base line period, 2-second cue period, 10-second task period, and 10~12-second rest period. Subjects are told not to blink their eyes during the motor imagery period. Every subject takes part in 3 sessions, and each session consists of 60 trials. To avoid subject fatigue, the trial number in a session is much less than traditional EEG paradigms. So we adopt the 5-fold cross-validation approach to reduce the effects of small trial number.

Six right handed healthy subjects (three males and three females, average age: 26.8 years) participate in the experiment. Three of them are trained three times before the experiment, and the others take part in no training course. All the subjects give written informed consent to participate in the experiment. Also, the experiment is approved by the Ethical Committee of the Shenyang Institute of Automation (SIA), Chinese Academy of Sciences (CAS).

2.2. Data Acquisition

21 Ag/AgCl electrodes above the primary motor cortex and the supplementary motor cortex are used in the experiment, as shown in Figure 2. A1 is used as the reference, and Fpz is used as the ground. Neuroscan synamps2 is used to acquire EEG signals from all the channels at a sampling frequency of 1000 Hz. The electrode impedance is reduced to 5 K Ohms before the experiment. The Electrooculogram (EOG) is also recorded to ensure that no EOG artifacts exist during the motor imagery task period.

3. Data Analysis Methods

The original EEG data are low-passed at a cutoff frequency of 125 Hz and then down sampled to 250 Hz to decrease the computation cost. Then, the frequencies from 5 Hz to 45 Hz are extracted for the following analysis. To improve the spatial resolution of the EEG data, a small Laplacian filter [28] is used as in where is the th channel, is the surrounding channel set of , is the size of , and is the th channel in .

As former researches show that mu rhythm and beta rhythm are effective for BCI control, the signals of 8–12 Hz and 18–25 Hz are extracted, respectively, for further analysis [29].

3.1. Hilbert Transform

Two methods can be used to get the phase information of a signal. The first one is the Hilbert transform method, and the other one is the complex wavelet convolution method [20]. Researches show that the results of the two methods are comparable [30]. We adopt the Hilbert transform method in the research.

The Hilbert transform of a signal can be gotten by convolution with the function , where is the Cauchy principal value. The analytic signal of can be gotten by (2). Consider where is the imaginary unit, is the instantaneous amplitude (IA), and is the instantaneous phase (IP). The value range of is . The instantaneous frequency (IF) can be gotten by . To get the correct instantaneous frequency, must be unwrapped by adding multiples of when absolute jumps of more than happen between consecutive elements.

3.2. Feature Extraction

Four feature types are researched in the paper: the power, the instantaneous amplitude (IA), the instantaneous phase (IP), and the instantaneous frequency (IF). The latter three features can be gotten from Hilbert transform.

To decrease the feature dimensions and improve the classification stability, the original features are averaged using an 0.5 s moving window with the step width of 0.125 s. Four window length and step width combinations are tested (0.5 s–0.125 s, 0.5 s–0.2 s, 1 s–0.125 s, and 1 s–0.2 s), and we find that the 0.5 s–0.125 s combination performs the best of all. The 0.5 s window length is reasonable taken into the consideration of the varied nature of EEG signals, and the 0.125 s step width is enough for fluent BCI device control. The averaged feature points between the time range of of all the channels are combined into a vector, and the different feature vector types are normalized and merged into a single vector according to the feature type combination situations.

In our research, we compared four different feature types and four different feature combination types. The four combination types are power-phase combination, amplitude-phase combination, amplitude-phase-frequency combination, and power-amplitude-phase-frequency combination.

3.3. Normalization

Due to the value range of the four feature types differing significantly from each other, normalization is essential to eliminate the degradation of the classifier performance and get better classification accuracy using the merged feature. In our paper, the feature vector of different types is normalized to the range using (4), and the normalized feature vectors are merged into a single vector for the following feature optimization and classification:

3.4. Feature Optimization

The original feature space may contain much redundant information, which may reduce the classification accuracy significantly. Feature optimization is the key to improve the discriminative performance of a classifier. Principle component analysis (PCA) is one type of feature optimization techniques that project the original feature space to another one [31]. The disadvantage of PCA is that the converted feature space is hard to understand. Feature selection is another type of feature optimization methods. This method selects a subset of features from the original feature space according to some criteria. Depending on whether the classifier is included in the selection process, feature selection methods can be grouped into “wrapper” methods and “filter” methods [32]. Generally speaking, the “wrapper” methods take the classifier’s classification accuracy as the feature selection criterion, thus getting better classification rate. However, its generalization ability is poor and its computational burden is much harder. In our research, we choose the “filter” method and compare two information based feature selection criteria: the mutual information feature selection (MIFS) criterion [33] and the max-relevance min-redundancy (mRMR) feature selection criterion [34].

The MIFS criterion uses the following equation to score the potentially usefulness of a feature or feature subset: where is the mutual information [35] between feature and class label , which is used to ensure feature relevance; is the mutual information between feature and features already selected in the currently selected feature set , which is used as a penalty to enforce low correlations. The value of depends on the independence level between and . A zero value means a full belief of the independence relations, and a one value means a full belief of the dependence relations.

The mRMR criterion uses the following equation to score the potentially usefulness of a feature or feature subset: The difference between MIFS criterion and mRMR criterion is that the value of MIFS is set by experience, while the value of mRMR is set inversely proportional to the size of the current feature set. The comparison between MIFS and mRMR can be found in [32, 36].

3.5. Support Vector Machines

Support vector machines (SVMs) have been used in the classification applications extensively due to their surprising classification ability [37]. Although it is originally proposed for binary classification, it can also be applied in multiclass classification problems through approaches of one-against-all (OAA) and one-against-one (OAO) methods [38]. SVMs can also be extended to solve regression problems by the introduction of the epsilon-insensitive loss function [39, 40]. By mapping the input samples (vectors) into a higher dimensional feature space using a kernel function [41] and by selecting the samples (the support vectors) that can produce the largest margin between two classes, SVMs demonstrate amazing results for both linear classification problems and nonlinear classification problems.

The decision function of SVMs has the following form: where is the training sample, is the sample’s target class label, is the weight vector used as a normal vector to determine the classification hyperplane, is a bias to adjust the location of the hyperplane for better classification results, and is the kernel function to map the sample into higher feature space. In our research, the linear kernel is used because it requires less parameters to optimize and can achieve much higher classification results compared with other kernels when their parameters are not optimized.

The distance between two different classes in the feature space is , so SVMs determine the classifier parameters by solving the following optimization problem: where is the training error and is a user-defined constant parameter used to provide a tradeoff between the separating margin and the training error. The optimization problem can be solved by Lagrange methods [37].

3.6. Extreme Learning Machines

Extreme learning machines (ELMs) are types of single-hidden layer feedforward neural networks (SLFNs) [42], which can be used for both regression and multiclass classification [43]. Unlike other feedforward neural networks that use gradient-based learning algorithms to tune all the network parameters iteratively, ELMs choose the input weights randomly and determine the output weights of SLFNs using an analytical approach. The advantages of ELMs contain extremely fast learning speed, the smallest training error, and better generalization performance. Huang et al. have rigorously proved that the input weights and hidden layer biases of SLFNs with infinitely differentiable activation functions can be randomly assigned [44].

For a training set , standard SLFNs with activation function and a hidden node number are mathematically modeled as where is the input weight vector that connects the input nodes and the th hidden node, is the output weight vector that connects the th hidden node and the output nodes, and is the bias of the th hidden node.

Equation (9) can be written in a compact format as where

When the input weight and the bias are given, the hidden layer output matrix can be calculated, and then the output weight can be calculated using the following equation: where is the Moore-Penrose generalized inverse of matrix [45].

3.7. Common Spatial Patterns

To validate the advantage of our method, we also classify clench speed and clench force motor imageries using the method of common spatial patterns (CSP). CSP is first applied to discriminate movement-related patterns by Müller-Gerking et al. in 1999 [46], and it has become a very popular method with many variants for motor imagery classification [47–49]. This method performs a weighting of the electrodes to maximize the difference between two different motor tasks, and the channel variance of the filtered signal is used for the classification in the following steps. The details of the algorithm can be found in [18].

In our research, the original EEG data are down sampled to 250 Hz first and then filtered in an 8–30 Hz band. No Laplacian filter is used to avoid zero eigenvalue when calculating the CSP model. Only two most important CSP patterns are used to get channel variance features; then SVMs and ELMs are used to classify these features, respectively.

4. Results

The topographies of the four different feature types are shown in Figure 3. While topographies of power feature and IA feature show little difference between clench force motor imagery and clench speed motor imagery, the topographies of IP and IF feature show significant difference between the two motor imagery tasks, which means that phase feature and its derivative contain some different information compared to the amplitude feature and power feature for motor parameters imagery.

(a)

(b)

(c)

(d)

The classification results of SVMs and ELMs using three different feature extraction methods (no-scaled with MIFS feature selection criterion, scaled with MIFS feature selection criterion, and scaled with mRMR feature selection criterion) and eight different feature types/combinations are shown in Table 1 and Figure 5. No significant difference between the classification rates between SVMs and ELMs for all the conditions can be found at the confidence level of 0.01 using -test.

Generally speaking, the scaled features have higher classification accuracy than the no-scaled features, and the mRMR feature selection criterion has higher classification accuracy than the MIFS feature selection criterion, as shown in Figures 4 and 6 and Tables 2 and 3. The feature numbers selected in the best feature subset using MIFS and mRMR are and for SVMs and and for ELMs. The classification accuracy of power feature and IA feature shows no significant difference. For the results using mRMR feature selection criterion and SVMs classifier, the IP feature and IF feature both have higher classification accuracy than power and IA feature at the confidence level of 0.01; both “IA-IP-IF” and “power-IA-IP-IF” feature combinations have higher classification accuracy than the other 6 features or feature combinations at a confidence level of 0.01. No significant difference between these two combinations is found.

(a)

(b)

(a)

(b)

(c)

(a)

(b)

The best classification rate between clench speed motor imagery and clench force motor imagery is 92% when “power-IA-IP-IF” combination feature and SVMs classifier are used. For comparison, the classification accuracies using CSP are and using ELMs and SVMs, respectively. This result demonstrates not only that using motor parameters imagery for BCI applications is possible but also that the time-frequency-phase method outperforms traditional CSP method.

5. Discussions and Conclusions

In this paper, we present the usefulness of phase information for BCI applications, which has been researched by few researchers before. We also demonstrate a new motor parameter imagery paradigm using clench speed and clench force as imagery tasks, and the results show that this paradigm has the potential ability to provide more direct control commands for BCI systems.

Two popular classification methods are compared in the paper using 5-fold cross validation, and no significant difference in the results is found between them. We only use the linear kernel for SVMs in this paper, and other kernels with parameter optimization may get better results. However, both kernel mapping and parameter optimization process require much computation cost. On the other hand, ELMs calculation is much simpler and faster, and no optimization process is needed, which is convenient for more applications.

We compare four different feature types (power, instantaneous amplitude [IA], instantaneous phase [IP], and instantaneous frequency [IF]) and four different feature combinations (power-IP, IA-IP, IA-IP-IF, and power-IA-IP-IF). The IA, IP, and IF features are calculated by Hilbert transform. We should notice that the IF feature is the derivative of the IP feature.

Three feature optimization processes are compared in this research: no-scaled feature using MIFS feature selection criterion, scaled feature using MIFS feature selection criterion, and scaled feature using mRMR feature selection criterion. Generally speaking, scaled feature combinations have higher classification accuracy than no-scaled feature combinations at a significant level of 0.01, which means that normalization is essential when merging two or more features together. The comparison of classification accuracy between MIFS feature selection criterion and mRMR feature selection criterion in Figure 4 demonstrates that the original feature space contains much redundant and irrelevant information for classification, and the mRMR criterion can choose the best feature subset more efficiently. The comparison of these two feature selection criteria can also be found in [32, 36]. The numbers selected in the best feature subset vary between different subjects and different sessions due to the variability of EEG signals, which means that the best feature indices should be adjusted every time for online applications.

When the four feature types are used independently, the IP feature and the IF feature both have higher classification accuracy than the power feature and the IA feature, but no significant difference is found between the results of IP and IF feature. When features are used in combinations, “IA-IP-IF” and “power-IA-IP-IF” feature combinations get the highest classification rate compared to the other 6 features/feature combinations. No significant difference is found between these two feature combinations, which means that the “IA-IP-IF” feature combination is enough for BCI applications.

In our research, all the features are extracted during the time range of , so our feature space contains feature of time domain. The four feature types are extracted from the mu rhythm and the beta rhythm, so the feature space contains feature of frequency domain. The IP feature and the IF feature are phase domain. So the “IA-IP-IF” and “power-IA-IP-IF” feature combinations are features of time-frequency-phase domain. Our results show that the usage of time-frequency-phase feature can improve the classification accuracy by about 20% and 15% compared to the time-frequency feature and the CSP method, respectively, which is very useful for improving BCI accuracy. Amplitude and phase are two important characteristics to describe a signal precisely. So, the time-frequency-phase feature can extract more information embedded in the motor imagery related EEG signals than the time-frequency features. Also, our results show that the classification between clench speed motor imagery and clench force motor imagery is possible, and the motor parameters imagery paradigm has the potential to increase the direct control commands for BCI applications.

In the future, we will analyze the EEG feature and the fNIRS feature simultaneously and investigate whether the multimodality method can improve the classification accuracy for BCI systems.

Conflict of Interests

The authors declare that there is no conflict of interests regarding the publication of this paper.

Acknowledgments

This work is supported by the National High Technology Research and Development Program of China (863 Program) under Grant no. 2012AA02A605 and the National Natural Science Foundation of China (NNSFC) under Grant nos. 61203368 and 61102014.

References

V. Gilja, P. Nuyujukian, C. A. Chestek et al., “A high-performance neural prosthesis enabled by control algorithm design,” Nature Neuroscience, vol. 15, no. 12, pp. 1752–1757, 2012.
View at: Publisher Site | Google Scholar
J. L. Collinger, B. Wodlinger, J. E. Downey et al., “High-performance neuroprosthetic control by an individual with tetraplegia,” The Lancet, vol. 381, no. 9866, pp. 557–564, 2013.
View at: Publisher Site | Google Scholar
I. Wickelgren, “Neuroprosthetics—brain-computer interface adds a new dimension,” Science, vol. 306, no. 5703, pp. 1878–1879, 2004.
View at: Google Scholar
S.-S. Yoo, H. Kim, E. Filandrianos, S. J. Taghados, and S. Park, “Non-Invasive Brain-to-Brain Interface (BBI): establishing functional links between two brains,” Plos ONE, vol. 8, no. 4, Article ID e60410, 2013.
View at: Publisher Site | Google Scholar
Q. Wang and O. Sourina, “Real-time mental arithmetic task recognition from EEG signals,” IEEE Transactions on Neural Systems and Rehabilitation Engineering, vol. 21, no. 2, pp. 225–232, 2013.
View at: Publisher Site | Google Scholar
Y. S. Zhang, P. Xu, Y. L. Huang, K. W. Cheng, and D. Z. Yao, “SSVEP response is related to functional brain network topology entrained by the flickering stimulus,” Plos ONE, vol. 8, no. 9, Article ID e72654, 2013.
View at: Google Scholar
Y. Shahriari and A. Erfanian, “Improving the performance of P300-based brain-computer interface through subspace-based filtering,” Neurocomputing, vol. 121, pp. 434–441, 2013.
View at: Publisher Site | Google Scholar
E. Thomas, J. Fruitet, and M. Clerc, “Combining ERD and ERS features to create a system-paced BCI,” Journal of Neuroscience Methods, vol. 216, no. 2, pp. 96–103, 2013.
View at: Publisher Site | Google Scholar
M. L. Stavrinou, L. Moraru, L. Cimponeriu, S. Della Penna, and A. Bezerianos, “Evaluation of cortical connectivity during real and imagined rhythmic finger tapping,” Brain Topography, vol. 19, no. 3, pp. 137–145, 2007.
View at: Publisher Site | Google Scholar
L. R. Hochberg and J. P. Donoghue, “Sensors for brain-computer interfaces: options for turning thought into action,” IEEE Engineering in Medicine and Biology Magazine, vol. 25, no. 5, pp. 32–38, 2006.
View at: Google Scholar
R. Sitaram, H. Zhang, C. Guan et al., “Temporal classification of multichannel near-infrared spectroscopy signals of motor imagery for developing a brain-computer interface,” NeuroImage, vol. 34, no. 4, pp. 1416–1427, 2007.
View at: Publisher Site | Google Scholar
S. Fazli, J. Mehnert, J. Steinbrink et al., “Enhanced performance by a hybrid NIRS-EEG brain computer interface,” NeuroImage, vol. 59, no. 1, pp. 519–529, 2012.
View at: Publisher Site | Google Scholar
S. Sanei, S. Ferdowsi, K. Nazarpour, and A. Cichocki, “Advances in electroencephalography signal processing,” IEEE Signal Processing Magazine, vol. 30, no. 1, pp. 170–176, 2013.
View at: Google Scholar
D. J. Krusienski, M. Grosse-Wentrup, F. Galán et al., “Critical issues in state-of-the-art brain-computer interface signal processing,” Journal of Neural Engineering, vol. 8, no. 2, Article ID 025002, 2011.
View at: Publisher Site | Google Scholar
H. Higashi and T. Tanaka, “Common spatio-time-frequency patterns for motor imagery-based brain machine interfaces,” Computational Intelligence and Neuroscience, 2013.
View at: Publisher Site | Google Scholar
K. C. Veluvolu, Y. Wang, and S. S. Kavuri, “Adaptive estimation of EEG-rhythms for optimal band identification in BCI,” Journal of Neuroscience Methods, vol. 203, no. 1, pp. 163–172, 2012.
View at: Publisher Site | Google Scholar
Y. Wang, K. C. Veluvolu, J.-H. Cho, and M. Defoort, “Adaptive estimation of EEG for subject-specific reactive band identification and improved ERD detection,” Neuroscience Letters, vol. 528, no. 2, pp. 137–142, 2012.
View at: Publisher Site | Google Scholar
H. Ramoser, J. Müller-Gerking, and G. Pfurtscheller, “Optimal spatial filtering of single trial EEG during imagined hand movement,” IEEE Transactions on Rehabilitation Engineering, vol. 8, no. 4, pp. 441–446, 2000.
View at: Publisher Site | Google Scholar
K. K. Ang, Z. Y. Chin, H. Zhang, and C. Guan, “Mutual information-based selection of optimal spatial-temporal patterns for single-trial EEG-based BCIs,” Pattern Recognition, vol. 45, no. 6, pp. 2137–2144, 2012.
View at: Publisher Site | Google Scholar
J.-P. Lachaux, E. Rodriguez, J. Martinerie, and F. J. Varela, “Measuring phase synchrony in brain signals,” Human Brain Mapping, vol. 8, no. 4, pp. 194–208, 1999.
View at: Google Scholar
E. Gysels and P. Celka, “Phase synchronization for the recognition of mental tasks in a brain-computer interface,” IEEE Transactions on Neural Systems and Rehabilitation Engineering, vol. 12, no. 4, pp. 406–415, 2004.
View at: Publisher Site | Google Scholar
J. Li and L. Zhang, “Phase interval value analysis for the motor imagery task in BCI,” Journal of Circuits, Systems and Computers, vol. 18, no. 8, pp. 1441–1452, 2009.
View at: Publisher Site | Google Scholar
C. Park, D. Looney, N. Ur Rehman, A. Ahrabian, and D. P. Mandic, “Classification of motor imagery BCI using multivariate empirical mode decomposition,” IEEE Transactions on Neural Systems and Rehabilitation Engineering, vol. 21, no. 1, pp. 10–22, 2013.
View at: Publisher Site | Google Scholar
E. V. C. Friedrich, R. Scherer, and C. Neuper, “Long-term evaluation of a 4-class imagery-based brain-computer interface,” Clinical Neurophysiology, vol. 124, no. 5, pp. 916–927, 2013.
View at: Publisher Site | Google Scholar
B. Obermaier, C. Neuper, C. Guger, and G. Pfurtscheller, “Information transfer rate in a five-classes brain-computer interface,” IEEE Transactions on Neural Systems and Rehabilitation Engineering, vol. 9, no. 3, pp. 283–288, 2001.
View at: Publisher Site | Google Scholar
B. Xu, Y. Fu, G. Shi, X. Yin, Z. Wang, and H. Li, “Improving classification accuracy by feature discretization and optimization for fNIRS based BCI systems,” Journal of Biomimetics Biomaterials and Tissue Engineering, vol. 19, no. 1, Article ID 1000119, 2014.
View at: Google Scholar
F. Matthews, B. A. Pearlmutter, T. E. Ward, C. Soraghan, and C. Markham, “Hemodynamics for brain-computer interfaces,” IEEE Signal Processing Magazine, vol. 25, no. 1, pp. 87–94, 2008.
View at: Publisher Site | Google Scholar
D. J. McFarland, L. M. McCane, S. V. David, and J. R. Wolpaw, “Spatial filter selection for EEG-based communication,” Electroencephalography and Clinical Neurophysiology, vol. 103, no. 3, pp. 386–394, 1997.
View at: Publisher Site | Google Scholar
D. J. McFarland, L. A. Miner, T. M. Vaughan, and J. R. Wolpaw, “Mu and beta rhythm topographies during motor imagery and actual movements,” Brain Topography, vol. 12, no. 3, pp. 177–186, 2000.
View at: Google Scholar
M. Le van Quyen, J. Foucher, J.-P. Lachaux et al., “Comparison of Hilbert transform and wavelet methods for the analysis of neuronal synchrony,” Journal of Neuroscience Methods, vol. 111, no. 2, pp. 83–98, 2001.
View at: Publisher Site | Google Scholar
X. Yu, P. Chum, and K. B. Sim, “Analysis the effect of PCA for feature reduction in non-stationary EEG based motor imagery of BCI system,” Optik, vol. 125, no. 3, pp. 1498–1502, 2014.
View at: Google Scholar
G. Brown, A. Pocock, M.-J. Zhao, and M. Luján, “Conditional likelihood maximisation: a unifying framework for information theoretic feature selection,” Journal of Machine Learning Research, vol. 13, pp. 27–66, 2012.
View at: Google Scholar
R. Battiti, “Using mutual information for selecting features in supervised neural net learning,” IEEE Transactions on Neural Networks, vol. 5, no. 4, pp. 537–550, 1994.
View at: Publisher Site | Google Scholar
H. Peng, F. Long, and C. Ding, “Feature selection based on mutual information: criteria of max-dependency, max-relevance, and min-redundancy,” IEEE Transactions on Pattern Analysis and Machine Intelligence, vol. 27, no. 8, pp. 1226–1238, 2005.
View at: Publisher Site | Google Scholar
C. E. Shannon, “A mathematical theory of communication,” Bell Systems Technical Journal, vol. 27, no. 3, pp. 379–423, 1948.
View at: Google Scholar
P. A. Estévez, M. Tesmer, C. A. Perez, and J. M. Zurada, “Normalized mutual information feature selection,” IEEE Transactions on Neural Networks, vol. 20, no. 2, pp. 189–201, 2009.
View at: Publisher Site | Google Scholar
C. Cortes and V. Vapnik, “Support-vector networks,” Machine Learning, vol. 20, no. 3, pp. 273–297, 1995.
View at: Publisher Site | Google Scholar
C.-W. Hsu and C.-J. Lin, “A comparison of methods for multiclass support vector machines,” IEEE Transactions on Neural Networks, vol. 13, no. 2, pp. 415–425, 2002.
View at: Publisher Site | Google Scholar
H. Drucker, C. J. C. Burges, L. Kaufman, A. Smola, and V. Vapnik, “Support vector regression machines,” in Advances in Neural Information Processing Systems, vol. 9, MIT Press, Cambridge, Mass, USA, 1997.
View at: Google Scholar
A. J. Smola and B. Schölkopf, “A tutorial on support vector regression,” Statistics and Computing, vol. 14, no. 3, pp. 199–222, 2004.
View at: Publisher Site | Google Scholar
K.-R. Müller, S. Mika, G. Rätsch, K. Tsuda, and B. Schölkopf, “An introduction to kernel-based learning algorithms,” IEEE Transactions on Neural Networks, vol. 12, no. 2, pp. 181–201, 2001.
View at: Publisher Site | Google Scholar
G.-B. Huang, Q.-Y. Zhu, and C.-K. Siew, “Extreme learning machine: a new learning scheme of feedforward neural networks,” in Proceedings of the IEEE International Joint Conference on Neural Networks, pp. 985–990, New York, NY, USA, July 2004.
View at: Publisher Site | Google Scholar
G.-B. Huang, H. Zhou, X. Ding, and R. Zhang, “Extreme learning machine for regression and multiclass classification,” IEEE Transactions on Systems, Man, and Cybernetics B: Cybernetics, vol. 42, no. 2, pp. 513–529, 2012.
View at: Publisher Site | Google Scholar
G.-B. Huang, Q.-Y. Zhu, and C.-K. Siew, “Extreme learning machine: theory and applications,” Neurocomputing, vol. 70, no. 1–3, pp. 489–501, 2006.
View at: Publisher Site | Google Scholar
C. R. Rao and S. K. Mitra, “Generalized inverse of a matrix and its applications,” in Proceedings of the 6th Berkeley Symposium on Mathematical Statistics and Probability, vol. 1, University of California Press, Berkeley, Calif, USA, 1972.
View at: Google Scholar
J. Müller-Gerking, G. Pfurtscheller, and H. Flyvbjerg, “Designing optimal spatial filters for single-trial EEG classification in a movement task,” Clinical Neurophysiology, vol. 110, no. 5, pp. 787–798, 1999.
View at: Publisher Site | Google Scholar
W. Samek, C. Vidaurre, K.-R. Müller, and M. Kawanabe, “Stationary common spatial patterns for brain-computer interfacing,” Journal of Neural Engineering, vol. 9, no. 2, Article ID 026013, 2012.
View at: Publisher Site | Google Scholar
H. Higashi and T. Tanaka, “Simultaneous design of FIR filter banks and spatial patterns for EEG signal classification,” IEEE Transactions on Biomedical Engineering, vol. 60, no. 4, pp. 1100–1110, 2013.
View at: Publisher Site | Google Scholar
J. Meng, G. Huang, D. Zhang, and X. Zhu, “Optimizing spatial spectral patterns jointly with channel configuration for brain-computer interface,” Neurocomputing, vol. 104, pp. 115–126, 2013.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2014 Baolei Xu et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

1744

Downloads

1125

Citations