A Numerical Simulation of Cell Separation by Simplified Asymmetric Pinched Flow Fractionation

Ma, Jing-Tao; Xu, Yuan-Qing; Tang, Xiao-Ying

doi:https://doi.org/10.1155/2016/2564584

Computational and Mathematical Methods in Medicine

On this page

Abstract Introduction Methods Results and Discussion Conclusion Acknowledgments References Copyright Related Articles

Special Issue

Computational Methods and Models in Circulatory and Reproductive Systems

View this Special Issue

Research Article | Open Access

Volume 2016 | Article ID 2564584 | https://doi.org/10.1155/2016/2564584

A Numerical Simulation of Cell Separation by Simplified Asymmetric Pinched Flow Fractionation

Jing-Tao Ma,^1,2Yuan-Qing Xu ,^1,3and Xiao-Ying Tang^1,3

Academic Editor: Yi Sui

Received15 Apr 2016

Accepted11 Jul 2016

Published15 Aug 2016

Abstract

As a typical microfluidic cell sorting technique, the size-dependent cell sorting has attracted much interest in recent years. In this paper, a size-dependent cell sorting scheme is presented based on a controllable asymmetric pinched flow by employing an immersed boundary-lattice Boltzmann method (IB-LBM). The geometry of channels consists of 2 upstream branches, 1 transitional channel, and 4 downstream branches (D-branches). Simulations are conducted by varying inlet flow ratio, the cell size, and the ratio of flux of outlet 4 to the total flux. It is found that, after being randomly released in one upstream branch, the cells are aligned in a line close to one sidewall of the transitional channel due to the hydrodynamic forces of the asymmetric pinched flow. Cells with different sizes can be fed into different downstream D-branches just by regulating the flux of one D-branch. A principle governing D-branch choice of a cell is obtained, with which a series of numerical cases are performed to sort the cell mixture involving two, three, or four classes of diameters. Results show that, for each case, an adaptive regulating flux can be determined to sort the cell mixture effectively.

1. Introduction

Sorting various categories of particles from the mixture to achieve pure sample is of great importance in biological and medical engineering. With the rapid development of micro total analysis systems, small sample volume, high throughput sample processing, high efficiency, and precise particle fractionation are several representative requirements to guide the design of sorting scheme [1]. And correspondingly, a host of particle sorting techniques have been developed in these years: for example, the fluorescence-activated cell sorting [2–4], magnetic-activated cell sorting [5–7], dielectrophoresis sorting [8, 9], and size-dependent sorting [10–12]. The last one has received a remarkable attention attributing to its promising advantages of low cost, high efficiency, and being label-free. There are four typical size-dependent sorting methods that are generally reported, the deterministic lateral displacement [10, 13], the pinched flow fractionation (PFF) [14–16], the cross-flow filtering [17], and the inertial focusing sorting [18]. PFF is relatively simple because there is no extra and specific microstructure needed in the channel, and it has been used to sort polymer beads [14], microparticles [19], and emulsion droplets [20] and for blood cells [21] in recent years. In these above researches, an asymmetric pinched flow fractionation scheme (AsPFF) proposed experimentally first by Takagi et al. [19] is reported to perform a continuous separation and collection for 1.5~5 μm particles; it bettered the traditional PFF remarkably, while there are still some aspects that could be improved, for example, to perform a hydrodynamic analysis and further develop an active and controllable cell or particle sorter.

In the present study, a numerical AsPFF cell sorter model is established with an immersed boundary-lattice Boltzmann method (IB-LBM), where the channel structure, the flow, the multiple sizes of cells, and their interactions are considered. Based on the model, cells with a prescribed size can be manipulated to enter a desired D-branch simply by regulating the flux of one D-branch (or the pressure of one outlet). The numerical results demonstrate that the numerical cell sorter is effective to perform an active and controllable cell sorting, which suggests an improved scheme of AsPFF and is valuable for guiding the experimental design of cell sorter on microfluidic chips.

2. Models and Methods

2.1. Mathematical Models

In the numerical model, the fluid motion is solved by LBM with D2Q9 lattice model. The discrete lattice Boltzmann equation of a single relaxation time model is [26–28]where is the distribution function for particles of velocity at position and time , is the time step, is the equilibrium distribution function, is the nondimensional relaxation time, and is the body force term. In the two-dimensional nine-speed (D2Q9) model [29], are given as follows:where is the lattice spacing. In (1), and are calculated by [26, 30]where are the weights defined by , for to , and for to , is the velocity of the fluid, is the speed of sound defined by , and is the body force acting on the fluid. The relaxation time related to the kinematic viscosity of the fluid is in terms of

Once the particle density distribution is known, the macroscopical quantities, including the fluid density, velocity, and pressure, are then computed from

Although the lattice Boltzmann method is original from a microscopic description of the fluid behavior, the macroscopic continuity (6) and momentum equations (7) can be recovered from it through the Chapman-Enskog multiscale analysis [31]. Then the LBM maybe can be viewed as a way of solving the macroscopic Navier-Stokes equations:

For the IB-LBM frame, the fluid motion is first solved by LBM; then the position of immersed boundary can be updated within one-time step of through [32]where is the position of the cell membrane at time . is the membrane velocity and is the fluid velocity. is the lattice side length; is the nearby area of the membrane defined by the Delta function [33–35]:where

In (9) and (10), denotes the total dimension of the model. The fluid-structure-interaction is enforced by the following equation [27, 32, 33, 36]:where is Lagrangian force acting on the ambient fluid by the cell membrane. In the present study, the cell model is proposed aswhere is the tensile force, is the bending force, is the normal force on the membrane which controls the cell incompressibility, and is the membrane-wall extrusion acting on the cell. The four force components are [33, 37–39]where , , , and are the constant coefficients for the corresponding force components. In (15), is the evolving cell area, is the reference cell area, and is unit normal vector pointing to fluid. In (16), is the position of the vessel wall, and is the cut-off distance of the effective scope in the membrane-wall interaction.

2.2. Physical Model and Simulation Setup

The geometry model of for cell sorting is illustrated in Figure 1, which consists of 2 upstream branches (U-branches), 1 transitional channel, and 4 downstream branches (D-branches). The U-branches and D-branches branches are labeled with the numbers, as well as the corresponding inlets and outlets. The two U-branches are perpendicular and symmetrical about the center line of the transitional channel. The transitional channel connects the U-branches and a circular buffer area which assembles the entrances of the four D-branches. The D-branches 1 and 4 are straight, while 2 and 3 are folded for the convenience to conduct the boundary condition of outlets; 1 and 4 are also symmetrical about the center line of the transitional channel, as well as 2 and 3. The entire length and width of device are 458 μm and 400 μm, respectively. The width of inlet 1 and inlet 2 is 70.71 μm. The width of pinched segment is 30 μm. The width of outlet 1, outlet 4, and unfolded part of outlets 2 and 3 is 26 μm. The width of folded part of outlets 2 and 3 is 23 μm. is defined as [19], where is the flux of a D-branch, is the pressure difference between the buffer center and the outlet, and is the flow resistance produced by the microchannel. In order to allocate the flow averagely for all the D-branches under the same pressure boundary conditions, s in all D-branches should be equal. A way to make be equal is described as two steps. First, set the pressure of all outlet to be the same. Second, change the length of the folded part of D-branches 2 and 3 until the stable flows of all outlets are equal. When sorting different size of cells, set the pressure of outlets 1, 2, and 3 to be the same, while the pressure of outlet 4 is regulatable, and the flows of D-branches can be reallocated by altering the outlet pressure. To quantify the the capacity of the reallocation of flow by regulating the flow of outlet 4, we define , where bigger means bigger flow through outlet 4 and smaller flow through 1, 2, and 3. In addition, since the flow resistance in each D-branch is the same, the flow is in proportion to ; that is, regulation of flow can be simply realized by regulating the pressure difference; this means that also can be defined as .

3. Results and Discussion

3.1. Validation

The method and model are validated carefully here by performing a simulation of flow past a stationary circular cylinder. This simulation is carried out by employing IB-LBM model. The computational domain is shown in Figure 2. The length and width of the computational domain are 1000 and 800, respectively. The center point of cylinder is located at and and the diameter of cylinder . The cylinder is discretized into a series of points, and the spacing between two adjacent points is 0.6. The cylinder is handled by utilizing immersed boundary method (IB), and the feedback-force principle is adopted to compute the force density on the cylinder, which is described as [22, 40]where denotes the interaction force between the fluid and the immersed boundary (cylinder), and are large negative free constants, is the fluid velocity obtained by interpolation at the IB, and is the velocity of the cylinder expressed by . Here, equals 0 because cylinder is stationary. In this case, the ratio of length of the recirculation zone and cylinder diameter , the drag force coefficient (18), the lift force coefficient (19), and the Strouhal number are calculated at Reynolds numbers 40 and 100:

The results are shown in Table 1. As shown in Table 1, the present results show close agreements with the general results reported by other literatures. This means the IB-LBM model adopted in present paper is accurate enough.

3.2. Determination of the Inlet Flow Ratio

In order to actualize the pinched flow to sort cells, it is necessary to establish an appropriate pinched segment in the transitional channel, which is able to lead all cells to move along with the lower sidewall of the transitional channel. There are three aspects for establishing the pinched segment. First, the width of the transitional channel is better to set as 1.3~1.5 times as the largest diameter of the cells, since it has been proved that a wider can reduce the fraction effect of pinched flow [14]. Second, the length of the transitional channel is suggested to set as 2 times as ; a too long transitional channel may result in central tendency of the flexible cells, which is unfavourable to control the cells to move along with the lower sidewall. Finally, the inlet flow ratio is also important to achieve the effective cell sorting. To get a proper , a set of numerical cases are performed by setting , and 10, where 20 cells with 8 μm diameter (the smallest size) are initialized and randomly placed in the U-branch 2 to test the function of the pinched flow. The cell center positions at the end of the transitional channel are recorded and shown in Figure 3.

As shown in Figure 3, the cell center positions when leaving the pinched segment drop with the increase of , and finally they reach a relatively steady state when . Although and seem to be much better, this means much higher shear stress, which may do damage to the cells. Therefore, is the choice for the present study.

3.3. Effect of and Cell Size on D-Branch Choice

In our consideration, specific, multiple classes of cells with different sizes can be sorted if every class enters a D-branch. In this section, the parameter and the cell size are regulated to manipulate a specific-diameter cell to enter one D-branch, and a series of numerical cases are performed to exhibit the relation of , the cell size, and the choice of D-branch. To set up the numerical model, is regulated from 0.1 to 0.9 with an increment of 0.1. Cells with the same initial diameter are released into U-branch 2. For each case of , four sizes of cell diameter are chosen as 8 μm, 16 μm, 20 μm, and 24 μm to make clear which D-branch a specific diameter of cells prefers to enter. In order to eliminate the possible effect of the initial position of the cell to the D-branch choice, in each case, three randomly placed cells are released into the U-branch, and all the D-branch choices are taken into account.

A D-branch choice for a rigid circular particle can be predicted by the following experimental equations [19]:where is the width of pinched segment as marked in Figure 1, is the outflow ratio at outlet 4, is the total number of outlets, and is the particle diameter. According to the above two equations, the particle will enter the th () D-branch if ranges in the scope which can be described with (20) or (21), where (20) is for , or 3, and (21) is only for .

The predicted and numerical results of the choice of D-branch which is related to the cell diameter and are exhibited in Figure 4. In these results, 11 numerical results out of 68 are found not to be consistent to the predicted results, which generally occur at the transition where the cell has approximate probability to enter two neighbouring D-branches. A most possible reason to result in the 11 differences is the predicted results are for rigid particles while cells are flexible.

According to the results, by regulating , the 8 μm and 16 μm cells can be sent into any one of all four D-branches, and some snapshots of the D-branch choice of 16 μm cell are displayed in Figure 5. By contrast, the 20 μm and 24 μm cells can select one of three D-branches labeled 2, 3, and 4, and the 20 μm cell snapshots are shown in Figure 6. The results indicate that, by simply regulating the flux of one D-branch, cells with the diameters ranging from 8 to 24 μm can be manipulated to enter different D-branches, which gives us an inspiration to sort cells with different sizes if they enter different D-branches at a given .

(a)

(b)

(c)

(d)

(a)

(b)

(c)

(d)

3.4. Size-Dependent Cell Sorting

As discussed in Section 3.3, cells with different diameters can be manipulated to choose a desired D-branch at a proper ; this gives us a potential scheme for sorting cell mixture with different sizes if the cell-cell interaction is not present; that is, all cells in mixture are discrete. In this section, a continuous size-dependent cell sorting is proposed based on the regulation of . According to Figure 4, it is clear which D-branch a certain cell will enter at a specific ; therefore, two sizes of cells are sorted once they enter different D-branches. For example, at , the 8 μm cell can be sorted from the 20 or 24 μm cell since 8 μm will enter D-branch 1 while the latter two will enter D-branch 2, and the same result will happen if the 8 μm cell is replaced by 16 μm cell. Some corresponding snapshots are shown as in Figures 7(a) and 7(b). By this means, at , it can be predicted that three sizes of cell can be sorted, they are 8, 16, and 20 μm cells or 8, 16, and 24 μm cells. Two snapshots of the two cases are displayed as in Figures 7(c) and 7(d), respectively. Especially at , the 8, 16, 20, and 24 μm are predicted to enter four different D-branches, and the numerical experiment result validates this actually as exhibited in Figure 7(e).

(a)

(b)

(c)

(d)

(e)

4. Summary and Conclusion

A size-dependent cell sorting model with an asymmetric pinched flow is investigated numerically by immersed boundary-lattice Boltzmann method. In the model, three aspects are summarized as the following. First, the geometry of the channels is designed specially according to the effective cell sorting, where the size of the transitional channel for controlling the pinched segment is discussed in detail. Second, the parameters and are defined, respectively, for the flux ratio of the two inlets and the flux proportion of outlet 4 in all outlets. is considered as a proper value to prepare for the cell sorting, based on which the regulation of can manipulate cells with different diameters to enter different D-branches. Finally, four sizes of cells are taken into account to exhibit the capacity of cell sorting, and the relations of the regulation flux, the cell size, and the choice of D-branch are analyzed systematically. The simulation results indicate that cells with different diameters can be successfully sorted into different D-branches, this evinces that the model we established is effective, which can provide a directive reference for the design of microfluidic chip for sorting multiple sizes of cells or particles.

Competing Interests

The authors declare that they have no competing interests.

Acknowledgments

This work is supported by the National Natural Science Foundation of China (no. 81301291) and the Beijing Higher Education Young Elite Teacher Project (no. YETP1208).

References

J. Autebert, B. Coudert, F.-C. Bidard et al., “Microfluidic: an innovative tool for efficient cell sorting,” Methods, vol. 57, no. 3, pp. 297–307, 2012.
View at: Publisher Site | Google Scholar
S. H. Cho, C. H. Chen, F. S. Tsai, J. M. Godin, and Y.-H. Lo, “Human mammalian cell sorting using a highly integrated micro-fabricated fluorescence-activated cell sorter (μFACS),” Lab on a Chip, vol. 10, no. 12, pp. 1567–1573, 2010.
View at: Publisher Site | Google Scholar
V. E. Gallardo and M. Behra, “Fluorescent activated cell sorting (FACS) combined with gene expression microarrays for transcription enrichment profiling of zebrafish lateral line cells,” Methods, vol. 62, no. 3, pp. 226–231, 2013.
View at: Publisher Site | Google Scholar
I. Van Brussel, R. Ammi, M. Rombouts et al., “Fluorescent activated cell sorting: an effective approach to study dendritic cell subsets in human atherosclerotic plaques,” Journal of Immunological Methods, vol. 417, pp. 76–85, 2015.
View at: Publisher Site | Google Scholar
H. Lee, A. M. Purdon, and R. M. Westervelt, “Manipulation of biological cells using a microelectromagnet matrix,” Applied Physics Letters, vol. 85, no. 6, pp. 1063–1065, 2004.
View at: Publisher Site | Google Scholar
K. Schriebl, G. Satianegara, A. Hwang et al., “Selective removal of undifferentiated human embryonic stem cells using magnetic activated cell sorting followed by a cytotoxic antibody,” Tissue Engineering Part A, vol. 18, no. 9-10, pp. 899–909, 2012.
View at: Publisher Site | Google Scholar
G. Welzel, D. Seitz, and S. Schuster, “Magnetic-activated cell sorting (MACS) can be used as a large-scale method for establishing zebrafish neuronal cell cultures,” Scientific Reports, vol. 5, article 7959, 2015.
View at: Publisher Site | Google Scholar
A. Valero, T. Braschler, N. Demierre, and P. Renaud, “A miniaturized continuous dielectrophoretic cell sorter and its applications,” Biomicrofluidics, vol. 4, no. 2, Article ID 022807, 2010.
View at: Publisher Site | Google Scholar
H. J. Song, J. M. Rosano, Y. Wang et al., “Continuous-flow sorting of stem cells and differentiation products based on dielectrophoresis,” Lab on a Chip, vol. 15, no. 5, pp. 1320–1328, 2015.
View at: Publisher Site | Google Scholar
J. V. Green, M. Radisic, and S. K. Murthy, “Deterministic lateral displacement as a means to enrich large cells for tissue engineering,” Analytical Chemistry, vol. 81, no. 21, pp. 9178–9182, 2009.
View at: Publisher Site | Google Scholar
J. Sun, C. Liu, M. Li et al., “Size-based hydrodynamic rare tumor cell separation in curved microfluidic channels,” Biomicrofluidics, vol. 7, no. 1, Article ID 011802, 2013.
View at: Publisher Site | Google Scholar
S. Song, M. S. Kim, J. Lee, and S. Choi, “A continuous-flow microfluidic syringe filter for size-based cell sorting,” Lab on a Chip, vol. 15, no. 5, pp. 1250–1254, 2015.
View at: Publisher Site | Google Scholar
J. McGrath, M. Jimenez, and H. Bridle, “Deterministic lateral displacement for particle separation: a review,” Lab on a Chip-Miniaturisation for Chemistry and Biology, vol. 14, no. 21, pp. 4139–4158, 2014.
View at: Publisher Site | Google Scholar
M. Yamada, M. Nakashima, and M. Seki, “Pinched flow fractionation: continuous size separation of particles utilizing a laminar flow profile in a pinched microchannel,” Analytical Chemistry, vol. 76, no. 18, pp. 5465–5471, 2004.
View at: Publisher Site | Google Scholar
A. L. Vig and A. Kristensen, “Separation enhancement in pinched flow fractionation,” Applied Physics Letters, vol. 93, no. 20, Article ID 203507, 2008.
View at: Publisher Site | Google Scholar
C. Cupelli, T. Borchardt, T. Steiner, N. Paust, R. Zengerle, and M. Santer, “Leukocyte enrichment based on a modified pinched flow fractionation approach,” Microfluidics and Nanofluidics, vol. 14, no. 3-4, pp. 551–563, 2013.
View at: Publisher Site | Google Scholar
Q. Wei, Y.-Q. Xu, F.-B. Tian, T.-X. Gao, X.-Y. Tang, and W.-H. Zu, “IB-LBM simulation on blood cell sorting with a micro-fence structure,” Bio-Medical Materials and Engineering, vol. 24, no. 1, pp. 475–481, 2014.
View at: Publisher Site | Google Scholar
X. Wang and I. Papautsky, “Size-based microfluidic multimodal microparticle sorter,” Lab on a Chip, vol. 15, no. 5, pp. 1350–1359, 2015.
View at: Publisher Site | Google Scholar
J. Takagi, M. Yamada, M. Yasuda, and M. Seki, “Continuous particle separation in a microchannel having asymmetrically arranged multiple branches,” Lab on a Chip, vol. 5, no. 7, pp. 778–784, 2005.
View at: Publisher Site | Google Scholar
H. Maenaka, M. Yamada, M. Yasuda, and M. Seki, “Continuous and size-dependent sorting of emulsion droplets using hydrodynamics in pinched microchannels,” Langmuir, vol. 24, no. 8, pp. 4405–4410, 2008.
View at: Publisher Site | Google Scholar
J. T. Ma, Y. Q. Xu, F. B. Tian, and X. Y. Tang, “IB-LBM study on cell sorting by pinched flow fractionation,” Bio-Medical Materials and Engineering, vol. 24, no. 6, pp. 2547–2554, 2014.
View at: Publisher Site | Google Scholar
D. V. Le, B. C. Khoo, and K. M. Lim, “An implicit-forcing immersed boundary method for simulating viscous flows in irregular domains,” Computer Methods in Applied Mechanics and Engineering, vol. 197, no. 25–28, pp. 2119–2130, 2008.
View at: Publisher Site | Google Scholar | MathSciNet
J. Wu and C. Shu, “Implicit velocity correction-based immersed boundary-lattice Boltzmann method and its applications,” Journal of Computational Physics, vol. 228, no. 6, pp. 1963–1979, 2009.
View at: Publisher Site | Google Scholar
Z. Wang, J. Fan, and K. Cen, “Immersed boundary method for the simulation of 2D viscous flow based on vorticity-velocity formulations,” Journal of Computational Physics, vol. 228, no. 5, pp. 1504–1520, 2009.
View at: Publisher Site | Google Scholar
S. K. Kang and Y. A. Hassan, “A comparative study of direct-forcing immersed boundary-lattice Boltzmann methods for stationary complex boundaries,” International Journal for Numerical Methods in Fluids, vol. 66, no. 9, pp. 1132–1158, 2011.
View at: Publisher Site | Google Scholar
Z. Guo, C. G. Zheng, and B. C. Shi, “Discrete lattice effects on the forcing term in the lattice Boltzmann method,” Physical Review E, vol. 65, no. 4, Article ID 046308, 6 pages, 2002.
View at: Publisher Site | Google Scholar
F.-B. Tian, H. Luo, L. Zhu, J. C. Liao, and X.-Y. Lu, “An efficient immersed boundary-lattice Boltzmann method for the hydrodynamic interaction of elastic filaments,” Journal of Computational Physics, vol. 230, no. 19, pp. 7266–7283, 2011.
View at: Publisher Site | Google Scholar | Zentralblatt MATH | MathSciNet
H.-B. Deng, Y.-Q. Xu, D.-D. Chen, H. Dai, J. Wu, and F.-B. Tian, “On numerical modeling of animal swimming and flight,” Computational Mechanics, vol. 52, no. 6, pp. 1221–1242, 2013.
View at: Publisher Site | Google Scholar | Zentralblatt MATH | MathSciNet
Y. H. Qian, D. Humieres, and P. Lallemand, “Lattice BGK models for NavierStokes equation,” Europhysics Letters, vol. 17, article 479, 1992.
View at: Google Scholar
D.-K. Sun, D. Jiang, N. Xiang, K. Chen, and Z.-H. Ni, “An immersed boundary-lattice boltzmann simulation of particle hydrodynamic focusing in a straight microchannel,” Chinese Physics Letters, vol. 30, no. 7, Article ID 074702, 2013.
View at: Publisher Site | Google Scholar
S. Chapman and T. G. Cowling, The Mathematical Theory of Non-Uniform Gases: An Account of the Kinetic Theory of Viscosity, Thermal Conduction and Diffusion in Gases, Cambridge University Press, 1991.
C. S. Peskin, “The immersed boundary method,” Acta Numerica, vol. 11, pp. 479–517, 2002.
View at: Publisher Site | Google Scholar | MathSciNet
Y.-Q. Xu, F.-B. Tian, and Y.-L. Deng, “An efficient red blood cell model in the frame of IB-LBM and its application,” International Journal of Biomathematics, vol. 6, no. 1, Article ID 1250061, 2013.
View at: Publisher Site | Google Scholar | MathSciNet
Y. Q. Xu, X. Y. Tang, F. B. Tian, Y. H. Peng, Y. Xu, and Y. J. Zeng, “IB-LBM simulation of the haemocyte dynamics in a stenotic capillary,” Computer Methods in Biomechanics and Biomedical Engineering, vol. 17, no. 9, pp. 978–985, 2014.
View at: Publisher Site | Google Scholar
X. Yang, X. Zhang, Z. Li, and G.-W. He, “A smoothing technique for discrete delta functions with application to immersed boundary method in moving boundary simulations,” Journal of Computational Physics, vol. 228, no. 20, pp. 7821–7836, 2009.
View at: Publisher Site | Google Scholar | Zentralblatt MATH | MathSciNet
Y. Cheng and H. Zhang, “Immersed boundary method and lattice Boltzmann method coupled FSI simulation of mitral leaflet flow,” Computers & Fluids, vol. 39, no. 5, pp. 871–881, 2010.
View at: Publisher Site | Google Scholar | MathSciNet
Y. Q. Xu, F. B. Tian, H. J. Li, and Y. L. Deng, “Red blood cell partitioning and blood flux redistribution in microvascular bifurcation,” Theoretical and Applied Mechanics Letters, vol. 2, no. 2, Article ID 024001, 2012.
View at: Publisher Site | Google Scholar
F.-B. Tian, “Role of mass on the stability of flag/flags in uniform flow,” Applied Physics Letters, vol. 103, no. 3, Article ID 034101, 2013.
View at: Publisher Site | Google Scholar
F.-B. Tian, H. X. Luo, L. D. Zhu, and X.-Y. Lu, “Coupling modes of three filaments in side-by-side arrangement,” Physics of Fluids, vol. 23, no. 11, Article ID 111903, 2011.
View at: Publisher Site | Google Scholar
W.-X. Huang and H. J. Sung, “An immersed boundary method for fluid-flexible structure interaction,” Computer Methods in Applied Mechanics and Engineering, vol. 198, no. 33–36, pp. 2650–2661, 2009.
View at: Publisher Site | Google Scholar

Copyright

Copyright © 2016 Jing-Tao Ma et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

PDF Download Citation

Download other formats

Order printed copies

Views

1802

Downloads

1411

Citations