Table of Contents Author Guidelines Submit a Manuscript
Advances in Power Electronics
Volume 2011 (2011), Article ID 832737, 10 pages
http://dx.doi.org/10.1155/2011/832737
Research Article

The Influence of Controller Parameters on the Quality of the Train Converter Current

Dipartimento di Energia, Politecnico di Milano, Piazza Leonardo da Vinci 32, 20133 Milano, Italy

Received 15 November 2010; Revised 25 March 2011; Accepted 31 March 2011

Academic Editor: C. M. Liaw

Copyright © 2011 M. Brenna et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. European Technical Specification for Interoperability (TSI) of the Railway Lines, 2008.
  2. M. Brenna, F. Foiadelli, G. C. Lazaroiu, and D. Zaninelli, “Four quadrant converter analysis for high speed trains,” in Proceedings of the 12th International Conference on Harmonics and Quality of Power, Cascais, Portugal, 2006.
  3. S. Ostlund, “Reduction of transformer rated power and line current harmonics in a primary switched converter system for traction applications,” in Proceedings of the 5th European Conference on Power Electronics and Applications (EPE '93), vol. 7, pp. 112–119, Brighton, UK, september 1993.
  4. S. Burdett, J. Allan, B. Mellitt, and J. Taufiq, “A power factor and harmonic comparison of AC railway power electronic traction converter circuits,” in Proceedings of the 5th European Conference on Power Electronics and Applications (EPE '93), pp. 235–240, Brighton, UK, 1993.
  5. W. Runge, “Control of line harmonics due to four-quadrant-converter in AC tractive stock by means of filter and transformer,” in Proceedings of the 7th European Conference on Power Electronics and Applications (EPE '97), pp. 3.459–3.464, Trondheim, Norway, 1997.
  6. G. W. Chang, H. W. Lin, and S. K. Chen, “Modeling characteristics of harmonic currents generated by high-speed railway traction drive converters,” IEEE Transactions on Power Delivery, vol. 19, no. 2, pp. 766–773, 2004. View at Publisher · View at Google Scholar · View at Scopus
  7. C. Bachle, H. P. Bauer, and T. Seger, “Requirements on the control of a three-level four quadrant power converter in a traction application,” in Proceedings of the 3rd European Conference on Power Electronics and Applications (EPE '89), vol. 2, pp. 577–582, Aachen, Germany, 1989.
  8. J. Carter, C. J. Goodman, and H. Zelaya, “Analysis of the single-phase four-quadrant PWM converter resulting in steady-state and small-signal dynamic models,” IEE Proceedings Electric Power Applications, vol. 144, no. 4, pp. 241–247, 1997. View at Publisher · View at Google Scholar
  9. D. Casadei, J. Clare, L. Empringham et al., “Large-signal model for the stability analysis of matrix converters,” IEEE Transactions on Industrial Electronics, vol. 54, no. 2, pp. 939–950, 2007. View at Publisher · View at Google Scholar · View at Scopus
  10. M. Brenna, G. C. Lazaroiu, G. Superti-Furga, and E. Tironi, “Bidirectional front end converter for DG with disturbance insensitivity and islanding-detection capability,” IEEE Transactions on Power Delivery, vol. 23, no. 2, pp. 907–914, 2008. View at Publisher · View at Google Scholar · View at Scopus
  11. M. S. Carmeli, F. Castelli Dezza, and G. Superti Furga, “Smart modulation: a new approach to power converter control,” in Proceedings of the 9th European Conference on Power Electronics and Applications (EPE '01), Graz, Austria, August 2001.