Table of Contents
Indian Journal of Materials Science
Volume 2015 (2015), Article ID 196178, 12 pages
http://dx.doi.org/10.1155/2015/196178
Research Article

Mechanical Characterization and Machinability Behavior of Annealed AISI D6 Cold Working Steel

Department of Mechanical Engineering, National Institute of Technology, Hamirpur 177005, India

Received 15 May 2015; Accepted 18 August 2015

Academic Editor: Jose L. Endrino

Copyright © 2015 Manoj Nayak et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. B. Podgornik, F. Majdic, V. Leskovsek, and J. Vizintin, “Improving tribological properties of tool steels through combination of deep-cryogenic treatment and plasma nitriding,” Wear, vol. 288, pp. 88–93, 2012. View at Publisher · View at Google Scholar · View at Scopus
  2. M. C. Shaw, Work Material Consideration, Metal Cutting Principles, Oxford University Press, Oxford, UK, 2nd edition, 2005.
  3. K. Amini, S. Nategh, and A. Shafyei, “Influence of different cryotreatments on tribological behavior of 80CrMo12 5 cold work tool steel,” Materials and Design, vol. 31, no. 10, pp. 4666–4675, 2010. View at Publisher · View at Google Scholar · View at Scopus
  4. R. N. Naravade, U. N. Gujar, and R. R. Kharde, “Optimization of cryogenic treatment on wear behaviour of AISI D6 tool steel by using DOE/RSM,” International Journal of Engineering and Advanced Technology, vol. 2, no. 2, pp. 239–244, 2012. View at Google Scholar
  5. J. D. Bressan, D. Kohls, and A. Tramontin, Fracture Toughness of AISI D6 Tool Steel As Received and with Heat Treatment, UDESCO, São Paulo, Brazil, 2013.
  6. J. P. Davim and L. Figueira, “Machinability evaluation in hard turning of cold work tool steel (D2) with ceramic tools using statistical techniques,” Materials and Design, vol. 28, no. 4, pp. 1186–1191, 2007. View at Publisher · View at Google Scholar · View at Scopus
  7. M. C. Cakir, C. Ensarioglu, and I. Demirayak, “Mathematical modeling of surface roughness for evaluating the effects of cutting parameters and coating material,” Journal of Materials Processing Technology, vol. 209, no. 1, pp. 102–109, 2009. View at Publisher · View at Google Scholar · View at Scopus
  8. B. Fnides, M. A. Yallese, T. Mabrouki, and J. F. Rigal, “Application of RSM for determining cutting force model in turning hardened AISI H11 hot work tool steel,” Indian Academy of Sciences, vol. 36, no. 1, pp. 109–203, 2011. View at Google Scholar
  9. K. Bouacha, M. A. Yallese, T. Mabrouki, and J.-F. Rigal, “Statistical analysis of surface roughness and cutting forces using response surface methodology in hard turning of AISI 52100 bearing steel with CBN tool,” International Journal of Refractory Metals and Hard Materials, vol. 28, no. 3, pp. 349–361, 2010. View at Publisher · View at Google Scholar · View at Scopus
  10. J. G. Lima, R. F. Ávila, A. M. Abrão, M. Faustino, and J. P. Davim, “Hard turning: AISI 4340 high strength low alloy steel and AISI D2 cold work tool steel,” Journal of Materials Processing Technology, vol. 169, no. 3, pp. 388–395, 2005. View at Publisher · View at Google Scholar · View at Scopus
  11. D. I. Lalwani, N. K. Mehta, and P. K. Jain, “Experimental investigations of cutting parameters influence on cutting forces and surface roughness in finish hard turning of MDN250 steel,” Journal of Materials Processing Technology, vol. 206, no. 1–3, pp. 167–179, 2008. View at Publisher · View at Google Scholar · View at Scopus
  12. A. Ebrahimi and M. M. Moshksar, “Evaluation of machinability in turning of microalloyed and quenched-tempered steels: tool wear, statistical analysis, chip morphology,” Journal of Materials Processing Technology, vol. 209, no. 2, pp. 910–921, 2009. View at Publisher · View at Google Scholar · View at Scopus
  13. ASM International, ASM Handbook Volume 9: Metallography and Microstructures, ASM International, Metals Park, Ohio, USA, 10th edition, 1990.
  14. ASM International, ASM Handbook Volume 1: Properties and Selection: Nonferrous Alloys and Special Purpose Materials, ASM International, Metals Park, Ohio, USA, 10th edition, 1990.
  15. Bureau of Indian Standard, “Methods for rockwell hardness test for metallic material,” IS 1586-2000, Bureau of Indian Standard, New Delhi, India, 1994. View at Google Scholar
  16. Bureau of Indian Standard, IS: 1501-2002 ‘Methods for Vicker Hardness Test for Metallic Material’, Bureau of Indian Standard (BIS), New Delhi, India, 3rd edition, 1997.
  17. Bureau of Indian Standard, “Metallic material, tensile testing at ambient temperature,” Tech. Rep. IS: 1608-2005, BIS, New Delhi, India, 1997, 3rd revision. View at Google Scholar
  18. Bureau of Indian Standard, “Method for charpy impact test (V-notch) on metallic material,” IS 1757-1988, Bureau of Indian Standard, New Delhi, India, 1989. View at Google Scholar
  19. D. C. Montogomery, Two-Level Factorial Design, Design and Analysis of Experiments, John Wiley & Sons, 7th edition, 2009.
  20. A. J. Makadia and J. I. Nanavati, “Optimisation of machining parameters for turning operations based on response surface methodology,” Measurement: Journal of the International Measurement Confederation, vol. 46, no. 4, pp. 1521–1529, 2013. View at Publisher · View at Google Scholar · View at Scopus
  21. I. Lazoglu, K. Buyukhatipoglu, H. Kratz, and F. Klocke, “Forces and temperatures in hard turning,” Machining Science and Technology, vol. 10, no. 2, pp. 157–179, 2006. View at Publisher · View at Google Scholar · View at Scopus