Table of Contents
Indian Journal of Materials Science
Volume 2015 (2015), Article ID 413593, 6 pages
http://dx.doi.org/10.1155/2015/413593
Research Article

Simulation of Ni-Based Super-Alloy and Optimizing of Its Mechanical Properties in a Near-Shaped Turbine Blade Part

School of Materials and Metallurgy Engineering, Iran University of Science and Technology, Tehran, Iran

Received 29 January 2015; Accepted 19 March 2015

Academic Editor: Kwo Young

Copyright © 2015 Mohammd Reza Alizadeh. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. K. S. Ho and W. S. Hwang, “Effects of casting and process designs on shrinkage porosity nozzle segments investment casting of Rene 77 Alloy,” AFS Transaction, pp. 1–15, 2002. View at Google Scholar
  2. M. Dumaillet and G. M. Wilson, “Comparison of flow modification trough foundry filters using both water. Modeling and simulation software,” AFS Transactions, vol. 110, pp. 1–12, 2002. View at Google Scholar
  3. A. K. M. B. Rashid and J. Campbell, “Oxide defects in a vacuum investment-cast nickel-based turbine blade,” AFS Transaction, pp. 158–167, 2004. View at Google Scholar
  4. R. E. Swift, J. H. Jackson, and L. W. Eastwood, “A study of principles of gating,” AFS Transactions, vol. 57, pp. 76–107, 1949. View at Google Scholar
  5. J. Campbell, Castings, Butterworth-Heinemann, 1991.
  6. J. Runyoro, S. M. A. Boutorabi, and J. Campbell, “Critical velocities for film-forming casting alloy,” AFS Transactions, vol. 100, pp. 225–234, 1992. View at Google Scholar
  7. S. L. Fry, “Preliminary investigation of metal pouring by cine radiography,” AFS Transactions, vol. 85, pp. 227–236, 1945. View at Google Scholar
  8. A. Onyszko, K. Kubiak, and J. Sieniawski, “Turbine blades of the single crystal nickel based CMSX-6 superalloy,” Journal of Achievement in Material and Manufacturing Engineering, vol. 32, pp. 66–69, 2009. View at Google Scholar
  9. X. Xue, S. F. Hansen, and P. N. Hansen, “Water analog study of effect of gating designs on inclusion and mold filling control,” AFS Transactions, vol. 101, pp. 199–209, 1993. View at Google Scholar
  10. P. Ingerslev and S. T. Anderson, “Flow analysis of mold filling using high speed motion picture of metal, water modeling and numerical calculation,” ISIJ International, vol. 86, no. 16, pp. 623–632, 1987. View at Google Scholar
  11. K. C. Mills, Y. M. Youssef, Z. Li, and Y. Su, “Calculation of thermophysical properties of Ni-based superalloys,” ISIJ International, vol. 46, no. 5, pp. 623–632, 2006. View at Publisher · View at Google Scholar · View at Scopus
  12. L. Pavlak, “Effect of filling conditions on the quality of cast aluminum cylinder heads,” Metalurgija, vol. 14, pp. 31–39, 2004. View at Google Scholar
  13. D. Z. Li, J. Campbell, and Y. Y. Li, “Filling system for investment cast Ni-base turbine blades,” Journal of Materials Processing Technology, vol. 148, no. 3, pp. 310–316, 2004. View at Publisher · View at Google Scholar · View at Scopus
  14. M. Barkhudarov and K. Williams, “Simulation of ‘surface turbulence’ fluid phenomena during mold filling,” in Proceedings of the AFS 99th Casting Congress on Flow Science, pp. 212–220, Kansas City, Mo, USA, April 1995.
  15. M. Cox, M. Wickins, J. P. Kuang, R. A. Harding, and J. Campbel, “Effect of top and bottom filling on reliability of investment castings in Al, Fe, and Ni-based alloys,” Materials Science and Technology, vol. 16, no. 11-12, pp. 1445–1452, 2000. View at Publisher · View at Google Scholar · View at Scopus
  16. H. Nieswaag and H. J. Deen, “Experiments on mould flow in thin wall casting,” in Proceedings of the 57th Word Foundry Congress, Osaka, Japan, 1990.
  17. S. H. Jony and S. H. Hwang, “Measurement of flow pattern for mold filling of castings,” AFS Transactions, vol. 99, pp. 69–75, 1991. View at Google Scholar