Table of Contents
Indian Journal of Materials Science
Volume 2016 (2016), Article ID 9380583, 8 pages
http://dx.doi.org/10.1155/2016/9380583
Research Article

Detecting Safety Zone Drill Process Parameters for Uncoated HSS Twist Drill in Machining GFRP Composites by Integrating Wear Rate and Wear Transition Mapping

1Department of Mechanical and Manufacturing Engineering, Manipal Institute of Technology, Manipal University, Manipal 576104, India
2Department of Humanities and Management, Manipal Institute of Technology, Manipal University, Manipal 576104, India

Received 4 March 2016; Revised 18 May 2016; Accepted 13 June 2016

Academic Editor: Pradeep Lancy Menezes

Copyright © 2016 Sathish Rao Udupi and Lewlyn Lester Raj Rodrigues. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. S. Gowri and F. H. Samuel, “Effect of alloying elements on the solidification characteristics and microstructure of Al–Si–Cu–Mg–Fe 380 alloy,” Metallurgical and Materials Transactions A, vol. 25, no. 2, pp. 437–448, 1994. View at Publisher · View at Google Scholar · View at Scopus
  2. H. R. Leep, E. D. Halbleib, and Z. Jiang, “Surface quality of holes drilled into aluminium 390,” International Journal of Production Research, vol. 29, no. 2, pp. 391–400, 1991. View at Publisher · View at Google Scholar · View at Scopus
  3. H. R. Leep and T. W. Eldridge, “Effects of cutting conditions on drilling of aluminum 380,” Journal of Materials Engineering and Performance, vol. 1, no. 6, pp. 797–800, 1992. View at Publisher · View at Google Scholar · View at Scopus
  4. M. Zhang, H. Zhou, T. Liang, and Y. B. Liu, “Intermetallic compounds in die casting aluminum alloys,” Special Casting or Nonferrous Alloys, vol. 1, pp. 117–119, 1999. View at Google Scholar
  5. M. Z. Zhang, Y. B. Liu, and H. Zhou, “Wear mechanism maps of uncoated HSS tools drilling die-cast aluminum alloy,” Tribology International, vol. 34, no. 11, pp. 727–731, 2001. View at Publisher · View at Google Scholar · View at Scopus
  6. J. Wang, Y. B. Liu, J. An, and L. M. Wang, “Wear mechanism map of uncoated HSS tools during drilling die-cast magnesium alloy,” Wear, vol. 265, no. 5-6, pp. 685–691, 2008. View at Publisher · View at Google Scholar · View at Scopus
  7. S. C. Lim and M. F. Ashby, “Wear-mechanism maps,” Acta Metallurgica, vol. 35, no. 1, pp. 1–24, 1987. View at Publisher · View at Google Scholar · View at Scopus
  8. M. F. Ashby and S. C. Lim, “Wear-mechanism maps,” Scripta Metallurgica et Materiala, vol. 24, no. 5, pp. 805–810, 1990. View at Publisher · View at Google Scholar · View at Scopus
  9. Z. Cao, LuLu, D. Sun, and Y. B. Liu, “Methodology and development of wear maps research,” Tribology International, vol. 17, pp. 187–192, 1997. View at Google Scholar
  10. Y. B. Liu, R. Asthana, and P. A. Rohatgi, “A map for wear mechanisms in aluminium alloys,” Journal of Materials Science, vol. 26, no. 1, pp. 99–102, 1991. View at Publisher · View at Google Scholar · View at Scopus
  11. S. C. Lim, S. H. Lee, Y. B. Liu, and K. H. W. Seah, “Wear maps for uncoated high-speed steel cutting tools,” Wear, vol. 170, no. 1, pp. 137–144, 1993. View at Publisher · View at Google Scholar · View at Scopus
  12. S. H. Lee, S. C. Lim, Y. B. Liu, and K. H. W. Seah, “Wear mechanism of cutting tools: uncoated high-speed-steel cutting tools,” Journal of Institute of Engineers, vol. 34, pp. 29–34, 1994. View at Google Scholar
  13. S. H. Lee, S. C. Lim, Y. B. Liu, and K. H. W. Seah, “Wear mechanism of cutting tools: uncoated carbide cutting tools,” Journal of Institute of Engineers, vol. 34, pp. 35–40, 1994. View at Google Scholar
  14. M. Roy, “Use of wear mechanism map to engineer surfaces for enhanced wear resistance,” Transactions of the Indian Institute of Metals, vol. 62, no. 3, pp. 197–208, 2009. View at Publisher · View at Google Scholar · View at Scopus
  15. S. Hernandez, Tribodays 2013, Luleå University of Technology, Luleå, Sweden, 2013.
  16. V. Srinivasan, K. V. Maheshkumar, R. Karthikeyan, and K. Palanikumar, “Application of probablistic neural network for the development of wear mechanism map for glass fiber reinforced plastics,” Journal of Reinforced Plastics and Composites, vol. 26, no. 18, pp. 1893–1906, 2007. View at Publisher · View at Google Scholar · View at Scopus