Table of Contents
ISRN Dentistry
Volume 2011, Article ID 810565, 7 pages
http://dx.doi.org/10.5402/2011/810565
Research Article

Effect of Margin Design and Processing Steps on Marginal Adaptation of Captek Restorations

Department of Restorative Dentistry, New Jersey Dental School, UMDNJ 110 Bergen Street, Newark, NJ 07103, USA

Received 18 April 2011; Accepted 9 May 2011

Academic Editors: G. Sjogren and C. G. Widmer

Copyright © 2011 Amy Shih et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. R. R. Seghi, S. F. Rosenstiel, and P. Bauer, “Abrasion of human enamel by different dental ceramics in vitro,” Journal of Dental Research, vol. 70, no. 3, pp. 221–225, 1991. View at Google Scholar · View at Scopus
  2. I. Shoher and A. Whiteman, “CaptekTM : a new capillary casting technology for ceramo-metal restorations,” Quintessence International, vol. 18, pp. 9–20, 1995. View at Google Scholar
  3. C. Zappala, I. Shoher, and P. Battaini, “Microstructural aspects of the CaptekTM alloy for porcelain-fused-to-metal restorations,” Journal of Esthetic Dentistry, vol. 8, no. 4, pp. 151–156, 1996. View at Google Scholar · View at Scopus
  4. J. J. Tuccillo and J. P. Nielsen, “Shear stress measurements at a dental porcelain-gold bond interface,” Journal of Dental Research, vol. 51, no. 2, pp. 626–633, 1972. View at Google Scholar · View at Scopus
  5. B. R. Lang, D. Gemalmaz, and N. A. Hasan, “Marginal fit changes during porcelain firing cycles,” The Journal of Prosthetic Dentistry, vol. 73, no. 1, pp. 49–54, 1995. View at Google Scholar · View at Scopus
  6. K. J. Anusavice and J. E. Carroll, “Effect of incompatibility stress on the fit of metal-ceramic crowns,” Journal of Dental Research, vol. 66, no. 8, pp. 1341–1345, 1987. View at Google Scholar · View at Scopus
  7. I. Shoher, “Vital tooth esthetics in Captek restorations,” Dental clinics of North America, vol. 42, no. 4, pp. 713–718, 1998. View at Google Scholar · View at Scopus
  8. R. Vasani, I. Kawashima, G. J. Ziebert et al., “Metal-ceramic interface evaluation of a gold-infiltrated alloy,” Journal of Prosthodontics, vol. 18, no. 7, pp. 560–565, 2009. View at Publisher · View at Google Scholar · View at PubMed · View at Scopus
  9. J. M. Goodson, I. Shoher, S. Imber et al., “Reduced dental plaque accumulation on composite gold alloy margins,” Journal of Periodontal Research, vol. 36, no. 4, pp. 252–259, 2001. View at Google Scholar · View at Scopus
  10. N. Juntavee, An investigation of the mechanical properties of a new ceramo-metal restoration (Captek), Doctor of Science Dissertation, Boston University, Boston, Mass,USA, 1995.
  11. N. Juntavee, D. Nathanson, and R. Giordano, A Research Report on Captek, International Association of Dental Research, 1995.
  12. T. V. Marghalani and D. Nathanson, “Marginal accuracy of sintered fixed partial dentures,” in Proceedings of the IADR Conference, Brisbane, Australia, 2006, abstract # 599.
  13. N. A. Wilson, S. A. Whitehead, I. A. Mjör et al., “Reasons for the placement and replacement of crowns in general dental practice,” Primary Dental Care, vol. 10, no. 2, pp. 53–59, 2003. View at Google Scholar · View at Scopus
  14. D. A. Felton, B. E. Kanoy, S. C. Bayne et al., “Effect of in vivo crown margin discrepancies on periodontal health,” The Journal of Prosthetic Dentistry, vol. 65, no. 3, pp. 357–364, 1991. View at Google Scholar · View at Scopus
  15. H. T. Shillingburg, S. Hobo, and D. W. Fisher, “Preparation design and margin distortion in porcelain-fused-to-metal restorations,” Journal of Prosthetic Dentistry, vol. 89, no. 6, pp. 527–532, 2003. View at Publisher · View at Google Scholar · View at Scopus
  16. J. R. Holmes, S. C. Bayne, G. A. Holland et al., “Considerations in measurement of marginal fit,” The Journal of Prosthetic Dentistry, vol. 62, no. 4, pp. 405–408, 1989. View at Google Scholar · View at Scopus
  17. G. J. Christensen, “Marginal fit of gold inlay castings,” The Journal of Prosthetic Dentistry, vol. 16, no. 2, pp. 297–305, 1966. View at Google Scholar · View at Scopus
  18. J. W. McLean and J. A. Von Fraunhofer, “The estimation of cement film thickness by an in vivo technique,” British Dental Journal, vol. 131, no. 3, pp. 107–111, 1971. View at Publisher · View at Google Scholar · View at Scopus
  19. H. W. Dedmon, “Ability to evaluate nonvisible margins with an explorer,” Operative dentistry, vol. 10, no. 1, pp. 6–11, 1985. View at Google Scholar · View at Scopus
  20. R. R. Faucher and J. I. Nicholls, “Distortion related to margin design in porcelain-fused-to-metal restorations,” The Journal of Prosthetic Dentistry, vol. 43, no. 2, pp. 149–155, 1980. View at Google Scholar · View at Scopus
  21. J. D. Preston, “Rational approach to tooth preparation for ceramo-metal restorations,” Dental Clinics of North America, vol. 21, no. 4, pp. 683–698, 1977. View at Google Scholar · View at Scopus
  22. P. H. DeHoff and K. J. Anusavice, “Effect of metal design on marginal distortion of metal-ceramic crowns,” Journal of Dental Research, vol. 63, no. 11, pp. 1327–1331, 1984. View at Google Scholar · View at Scopus
  23. H. Hamaguchi, A. Cacciatore, and V. M. Tueller, “Marginal distortion of the porcelain-bonded-to-metal complete crown: an SEM study,” The Journal of Prosthetic Dentistry, vol. 47, no. 2, pp. 146–153, 1982. View at Google Scholar · View at Scopus