Table of Contents
Journal of Ceramics
Volume 2013 (2013), Article ID 430408, 6 pages
http://dx.doi.org/10.1155/2013/430408
Research Article

Influence of the Dopants on the Mechanical Properties of Alumina-Based Ceramics

Institute of Electrophysics UD RAS, Amundsen Street, 106, Yekaterinburg 620016, Russia

Received 29 September 2013; Revised 30 October 2013; Accepted 11 November 2013

Academic Editor: Young-Wook Kim

Copyright © 2013 Anton Sergeevich Kaygorodov et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. D. Sherman and D. Brandon, “Mechanical properties of hard materials and their relation to microstructure,” Advanced Engineering Materials, vol. 1, no. 3-4, pp. 161–181, 1999. View at Google Scholar · View at Scopus
  2. B. Kerkwijk, E. Mulder, and H. Verweij, “Zirconia-alumina ceramic composites with extremely high wear resistance,” Advanced Engineering Materials, vol. 1, no. 1, pp. 69–71, 1999. View at Google Scholar · View at Scopus
  3. A. I. Gusev and A. A. Rempel, Nanocrystalline Materials, Cambridge International Science Publishing, 2004.
  4. H. Awaji, T. Matsunaga, and S.-M. Choi, “Relation between strength, fracture toughness, and critical frontal process zone size in ceramics,” Materials Transactions, vol. 47, no. 6, pp. 1532–1539, 2006. View at Publisher · View at Google Scholar · View at Scopus
  5. A. A. Abramovich, O. V. Karban', V. V. Ivanov, and E. I. Salamatov, “Influence of the structure on the thermal conductivity of the Al2O3+ Fe nanocomposite,” Glass Physics and Chemistry, vol. 31, no. 5, pp. 709–711, 2005. View at Publisher · View at Google Scholar · View at Scopus
  6. M. Backhaus-Ricoult, V. Guérin, J. Deschamps, and B. Pellissier, “Increase in fracture toughness of monolithic ceramics by a partial reduction treatment,” Key Engineering Materials, vol. 132–136, pp. 516–519, 1997. View at Google Scholar · View at Scopus
  7. M. D. Snel, G. de With, F. Snijkers, J. Luyten, and A. Kodentsov, “Aqueous tape casting of reaction bonded aluminium oxide (RBAO),” Journal of the European Ceramic Society, vol. 27, no. 1, pp. 27–33, 2007. View at Publisher · View at Google Scholar · View at Scopus
  8. I.-W. Chen and X.-H. Wang, “Sintering dense nanocrystalline ceramics without final-stage grain growth,” Nature, vol. 404, no. 6774, pp. 168–171, 2000. View at Publisher · View at Google Scholar · View at Scopus
  9. V. V. Ivanov, S. N. Paranin, and V. R. Khrustov, “Nanostructured ceramics based on aluminum and zirconium oxides produced using magnetic pulsed pressing,” Physics of Metals and Metallography, vol. 94, no. 1, pp. S98–S106, 2002. View at Google Scholar · View at Scopus
  10. G. R. Anstis, P. Chantikul, B. R. Lawn, and D. B. Marshall, “A critical evaluation of indentation techniques for measuring fracture toughness: I, direct crack measurements,” Journal of American Ceramic Society, vol. 64, pp. 533–538, 1981. View at Google Scholar
  11. A. Franco and S. G. Roberts, “Controlled wet erosive wear of polycrystalline alumina,” Journal of the European Ceramic Society, vol. 16, no. 12, pp. 1365–1375, 1996. View at Publisher · View at Google Scholar · View at Scopus
  12. A. Kaygorodov and V. Khrustov, “The influence of Al2O3+Al powders stirring time on the quality of alumina-based ceramics,” Epitoanyag, vol. 62, pp. 116–118, 2010. View at Google Scholar
  13. R. W. Siegel, “Nanostructured materials -mind over matter-,” Nanostructured Materials, vol. 4, no. 1, pp. 121–138, 1994. View at Google Scholar · View at Scopus
  14. I. P. Shapiro, R. I. Todd, J. M. Titchmarsh, and S. G. Roberts, “An indentation model for erosive wear in Al2O3/SiC nanocomposites,” Journal of the European Ceramic Society, vol. 31, no. 1-2, pp. 85–95, 2011. View at Publisher · View at Google Scholar · View at Scopus