Table of Contents
Journal of Composites
Volume 2013 (2013), Article ID 970954, 7 pages
http://dx.doi.org/10.1155/2013/970954
Research Article

Experimental and Modeling Study of the Turning Process of PA 6/Nano Calcium Carbonate Composite

1Department of Mechanical Engineering, University of Tabriz, Tabriz, Tabriz 51666-16471, Iran
2Department of Mechanical Engineering, Amirkabir University of Technology, 424 Hafez Avenue, Tehran 15875-4413, Iran

Received 19 January 2013; Revised 13 May 2013; Accepted 14 May 2013

Academic Editor: Zhiping Luo

Copyright © 2013 Mehdi Haghi et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. S. N. Bhattacharya, M. R. Kamal, and R. K. Gupta, Polymeric Nanocomposites: Theory and Practice, Hanser Gardner, 2008.
  2. S. C. Tjong, Y. Z. Meng, and Y. Xu, “Structure and properties of polyamide-6/vermiculite nanocomposites prepared by direct melt compounding,” Journal of Polymer Science B, vol. 40, no. 24, pp. 2860–2870, 2002. View at Publisher · View at Google Scholar · View at Scopus
  3. M. Alexandre and P. Dubois, “Polymer-layered silicate nanocomposites: preparation, properties and uses of a new class of materials,” Materials Science and Engineering, vol. 28, no. 1, pp. 1–63, 2000. View at Publisher · View at Google Scholar · View at Scopus
  4. F. Z. Fang and Y. C. Liu, “On minimum exit-burr in micro cutting,” Journal of Micromechanics and Microengineering, vol. 4, pp. 984–988, 2004. View at Google Scholar
  5. W. Wang, S. H. Kweon, and S. H. Yang, “A study on roughness of the micro-end-milled surface produced by a miniatured machine tool,” Journal of Materials Processing Technology, vol. 162-163, pp. 702–708, 2005. View at Publisher · View at Google Scholar
  6. F. Mata, P. Reis, and J. P. Davim, “Physical cutting model of polyamide composites (PA66 GF30),” Materials Science Forum, vol. 514–516, no. 1, pp. 643–647, 2006. View at Google Scholar · View at Scopus
  7. J. P. Davim and F. Mata, “A comparative evaluation of the turning of reinforced and unreinforced polyamide,” International Journal of Advanced Manufacturing Technology, vol. 33, pp. 911–914, 2007. View at Google Scholar
  8. V. G. Dhokia, S. Kumar, P. Vichare, S. T. Newman, and R. D. Allen, “Surface roughness prediction model for CNC machining of polypropylene,” Proceedings of the Institution of Mechanical Engineers B, vol. 222, no. 2, pp. 137–153, 2008. View at Publisher · View at Google Scholar · View at Scopus
  9. V. G. Dhokia, S. Kumar, P. Vichare, and S. T. Newman, “An intelligent approach for the prediction of surface roughness in ball-end machining of polypropylene,” Robotics and Computer-Integrated Manufacturing, vol. 24, no. 6, pp. 835–842, 2008. View at Publisher · View at Google Scholar · View at Scopus
  10. J. P. Davim, L. R. Silva, A. Festas, and A. M. Abrão, “Machinability study on precision turning of PA66 polyamide with and without glass fiber reinforcing,” Materials and Design, vol. 30, no. 2, pp. 228–234, 2009. View at Publisher · View at Google Scholar · View at Scopus
  11. M. R. Razfar, R. Farshbaf Zinati, and M. Haghshenas, “Optimum surface roughness prediction in face milling by using neural network and harmony search algorithm,” International Journal of Advanced Manufacturing Technology, vol. 52, no. 5–8, pp. 487–495, 2011. View at Publisher · View at Google Scholar · View at Scopus
  12. R. F. Zinati and M. R. Razfar, “Constrained optimum surface roughness prediction in turning of X20Cr13 by coupling novel modified harmony search-based neural network and modified harmony search algorithm,” The International Journal of Advanced Manufacturing Technology, vol. 58, no. 1–4, pp. 93–107, 2012. View at Publisher · View at Google Scholar
  13. M. Farahnakian, M. R. Razfar, M. Moghri, and M. Asadnia, “The selection of milling parameters by the PSO-based neural network modeling method,” The International Journal of Advanced Manufacturing Technology, vol. 57, no. 1–4, pp. 49–60, 2011. View at Publisher · View at Google Scholar
  14. E. J. A. Armarego and R. H. Brown, The Machining of Metals, Prentice-Hall, Upper Saddle River, NJ, USA, 1967.
  15. M. P. Groover, Fundamentals of Modern Manufacturing, Materials, Processes, and Systems, John Wiley & Sons, New York, Ny, USA, 2007.