Table of Contents
Journal of Composites
Volume 2015 (2015), Article ID 971596, 9 pages
http://dx.doi.org/10.1155/2015/971596
Research Article

Experimental Investigations into Abrasive Waterjet Machining of Carbon Fiber Reinforced Plastic

1Marathwada Institute of Technology, Aurangabad 431028, India
2Dr. Babasaheb Ambedkar Technological University, Lonere 402103, India
3Defence Institute of Advanced Technology, Pune 411025, India

Received 2 June 2015; Revised 18 August 2015; Accepted 6 September 2015

Academic Editor: Nikhil Gupta

Copyright © 2015 Prasad D. Unde et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. D. K. Shanmugam, F. L. Chen, E. Siores, and M. Brandt, “Comparative study of jetting machining technologies over laser machining technology for cutting composite materials,” Composite Structures, vol. 57, no. 1–4, pp. 289–296, 2002. View at Publisher · View at Google Scholar · View at Scopus
  2. D. Babu Rao, D. Baskey, and R. S. Rawat, “Water jet cutter: an efficient tool for composite product development,” in Proceedings of the National Conference on Scientific Achievements of SC & ST Scientists & Technologists, pp. 104–107, Bangalore, India, April 2009.
  3. P. A. Carraro, L. Maragoni, and M. Quaresimin, “Influence of manufacturing induced defects on damage initiation and propagation in carbon/epoxy NCF laminates,” Advanced Manufacturing: Polymer & Composites Science, vol. 1, no. 1, pp. 44–53, 2015. View at Publisher · View at Google Scholar
  4. V. Mutavgjic, Z. Jurkovic, M. Franulovic, and M. Sekulic, “Experimental investigation of surface roughness obtained by abrasive water jet machining,” in Proceedings of the 15th International Research/Expert Conference Trends in the Development of Machinery and Associated Technology (TMT '11), pp. 73–76, Prague, Czech Republic, September 2011.
  5. D. K. Shanmugam, T. Nguyen, and J. Wang, “A study of delamination on graphite/epoxy composites in abrasive waterjet machining,” Composites A: Applied Science and Manufacturing, vol. 39, no. 6, pp. 923–929, 2008. View at Publisher · View at Google Scholar · View at Scopus
  6. T. U. Siddiqui, M. Shukla, and P. B. Tambe, “Comparative investigation of abrasive waterjet cut kerf quality characteristics for aramid, glass and carbon fiber reinforced composites used in transport aircraft applications,” in Proceedings of the American WJTA Conference and Expo, pp. 53–68, Houston, Tex, USA, August 2009.
  7. M. A. Azmir and A. K. Ahsan, “Investigation on glass/epoxy composite surfaces machined by abrasive water jet machining,” Journal of Materials Processing Technology, vol. 198, no. 1–3, pp. 122–128, 2008. View at Publisher · View at Google Scholar · View at Scopus
  8. S. Libuse, L. Imrich, K. Jana, and S. Oldrich, Waterjet Cutting and Surface Quality Nonconventional Technologies Review, Romanian Association of Nonconventional Technologies, Bucharest, Romania, 2013.
  9. M. Ramulu and D. Arola, “Water jet and abrasive water jet cutting of unidirectional graphite/epoxy composite,” Composites, vol. 24, no. 4, pp. 299–308, 1993. View at Publisher · View at Google Scholar · View at Scopus
  10. H. Ho-Cheng, “A failure analysis of water jet drilling in composite laminates,” International Journal of Machine Tools and Manufacture, vol. 30, no. 3, pp. 423–429, 1990. View at Publisher · View at Google Scholar · View at Scopus
  11. B. Chandra and J. Singh, “A study of effect of process parameters of abrasive jet machining,” International Journal of Engineering Science and Technology, vol. 3, pp. 504–513, 2011. View at Google Scholar
  12. J. Wang, “A machinability study of polymer matrix composites using abrasive waterjet cutting technology,” Journal of Materials Processing Technology, vol. 94, no. 1, pp. 30–35, 1999. View at Publisher · View at Google Scholar · View at Scopus
  13. A. Stoić, M. Duspara, B. Kosec, M. Stoić, and I. Samardžić, “Application of water jet for cutting polymer materials,” Metalurgija, vol. 52, no. 2, pp. 255–258, 2013. View at Google Scholar · View at Scopus
  14. M. Hagino and T. Inoue, “Effect of carbon fiber orientation and helix angle on CFRP cutting characteristics by end-milling,” International Journal of Automation Technology, vol. 7, no. 3, pp. 292–299, 2013. View at Google Scholar · View at Scopus
  15. J. François Chatelain, “Effect of ply orientation on roughness for the trimming process of CFRP laminates,” World Academy of Science, Engineering and Technology, vol. 6, pp. 988–994, 2012. View at Google Scholar
  16. N. G. Patil, A. Asem, R. S. Pawade, D. G. Thakur, and P. K. Brahmankar, “Comparative study of high speed machining of Inconel 718 in dry condition and by using compressed cold carbon dioxide gas as coolant,” Procedia CIRP, vol. 24, pp. 86–91, 2014. View at Publisher · View at Google Scholar
  17. R. H. Myers, D. C. Montgomery, and C. M. Anderson-Cook, Response Surface Methodology: Process And Product Optimization Using Designed Experiments, John Wiley & Sons, New York, NY, USA, 1996. View at MathSciNet
  18. M. A. Azmir and A. K. Ahsan, “A study of abrasive water jet machining process on glass/epoxy composite laminate,” Journal of Materials Processing Technology, vol. 209, no. 20, pp. 6168–6173, 2009. View at Publisher · View at Google Scholar · View at Scopus
  19. D. F. Liu, Y. J. Tang, and W. L. Cong, “A review of mechanical drilling for composite laminates,” Composite Structures, vol. 94, no. 4, pp. 1265–1279, 2012. View at Publisher · View at Google Scholar · View at Scopus
  20. M. M. Korat and G. D. Acharya, “A review on current research and development in abrasive waterjet machining,” International Journal of Engineering Research and Applications, vol. 4, no. 1, pp. 423–432, 2014. View at Google Scholar