Table of Contents
Journal of Structures
Volume 2014 (2014), Article ID 387680, 7 pages
http://dx.doi.org/10.1155/2014/387680
Research Article

Stress-Strain Compression of AA6082-T6 Aluminum Alloy at Room Temperature

Department of Mechanical Engineering, Pontifical Catholic University of Minas Gerais, 30535-901 Belo Horizonte, MG, Brazil

Received 16 June 2014; Revised 15 October 2014; Accepted 28 October 2014; Published 13 November 2014

Academic Editor: Hanxing Zhu

Copyright © 2014 Alexandre da Silva Scari et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. O. S. Hopperstad, M. Langseth, and T. Tryland, “Ultimate strength of aluminium alloy outstands in compression: experiments and simplified analysis,” Thin-Walled Structures, vol. 34, no. 4, pp. 279–294, 1999. View at Publisher · View at Google Scholar · View at Scopus
  2. E. Andrews, W. Sanders, and L. J. Gibson, “Compressive and tensile behaviour of aluminum foams,” Materials Science and Engineering A, vol. 270, no. 2, pp. 113–124, 1999. View at Publisher · View at Google Scholar · View at Scopus
  3. G. Gioux, T. M. McCormack, and L. J. Gibson, “Failure of aluminum foams under multiaxial loads,” International Journal of Mechanical Sciences, vol. 42, no. 6, pp. 1097–1117, 2000. View at Publisher · View at Google Scholar · View at Scopus
  4. J. B. Ferguson, M. Tabandeh-Khorshid, P. K. Rohatgi, K. Cho, and C.-S. Kim, “Predicting tensile and compressive mechanical properties of bimodal nano-aluminum alloys,” Scripta Materialia, vol. 72-73, pp. 13–16, 2014. View at Publisher · View at Google Scholar · View at Scopus
  5. F. Pled, W. Yan, and C. Wen, “Crushing modes of aluminium tubes under axial compression,” in Proceedings of the 5th Australasian Congress on Applied Mechanics, December 2007.
  6. H. N. Han and K.-H. Kim, “A ductile fracture criterion in sheet metal forming process,” Journal of Materials Processing Technology, vol. 142, no. 1, pp. 231–238, 2003. View at Publisher · View at Google Scholar · View at Scopus
  7. J. Luo, M. Q. Li, and D. W. Ma, “The deformation behavior and processing maps in the isothermal compression of 7A09 aluminum alloy,” Materials Science and Engineering A, vol. 532, pp. 548–557, 2012. View at Publisher · View at Google Scholar · View at Scopus
  8. D. W. A. Rees, “Plane strain compression of aluminium alloy sheets,” Materials & Design, vol. 39, pp. 495–503, 2012. View at Publisher · View at Google Scholar · View at Scopus
  9. B. Wu, M. Q. Li, and D. W. Ma, “The flow behavior and constitutive equations in isothermal compression of 7050 aluminum alloy,” Materials Science and Engineering A, vol. 542, pp. 79–87, 2012. View at Publisher · View at Google Scholar · View at Scopus
  10. T. Kyačkaj, R. Kočiško, J. Tiža et al., “Application of workability test to SPD processing,” Archives of Metallurgy and Materials, vol. 58, no. 2, pp. 407–412, 2013. View at Publisher · View at Google Scholar · View at Scopus
  11. A. Stefanik, H. Dyja, and S. Mróz, “Determination of the critical value of normalized Cocroft-Latham criterion during multi slight rolling based on tensile test,” Archives of Metallurgy and Materials, vol. 56, no. 2, pp. 543–550, 2011. View at Publisher · View at Google Scholar · View at Scopus
  12. Y.-F. Xia, G.-Z. Quan, and J. Zhou, “Effects of temperature and strain rate on critical damage value of AZ80 magnesium alloy,” Transactions of Nonferrous Metals Society of China, vol. 20, no. 2, pp. s580–s583, 2010. View at Publisher · View at Google Scholar · View at Scopus
  13. S. Alexandrov and Y.-R. Jeng, “An efficient method for the identification of the modified Cockroft-Latham fracture criterion at elevated temperature,” Archive of Applied Mechanics, vol. 83, no. 12, pp. 1801–1804, 2013. View at Publisher · View at Google Scholar · View at Zentralblatt MATH · View at Scopus
  14. G.-Z. Quan, G.-C. Luo, A. Mao, J.-T. Liang, and D.-S. Wu, “Evaluation of varying ductile fracture criteria for 42CrMo steel by compressions at different temperatures and strain rates,” The Scientific World Journal, vol. 2014, Article ID 579328, 10 pages, 2014. View at Publisher · View at Google Scholar · View at Scopus
  15. J. Landre, A. Pertence, P. R. Cetlin, J. M. C. Rodrigues, and P. A. F. Martins, “On the utilisation of ductile fracture criteria in cold forging,” Finite Elements in Analysis and Design, vol. 39, no. 3, pp. 175–186, 2003. View at Publisher · View at Google Scholar · View at Scopus
  16. M. Meyers and K. Chawla, Mechanical Behavior of Materials, Cambridge University Press, New York, NY, USA, 2nd edition, 2009.
  17. ASTM, “Standard test methods of compression testing of metallic materials at room temperature,” ASTM E9-09, 2009. View at Google Scholar
  18. N. E. Dowling, Mechanical Behavior of Materials, Pearson Prentice Hall, Upper Saddle River, NJ, USA, 3rd edition, 2007.
  19. “Material property data—MATWEB. Mechanical properties of AA6082 T6 aluminum alloy,” http://www.matweb.com/search/DataSheet.aspx?MatGUID=fad29be6e64d4e95a241690f1f6e1eb7.
  20. W. F. Hosford, Mechanical Behavior of Materials, Cambridge University Press, New York, NY, USA, 2005.