Table of Contents Author Guidelines Submit a Manuscript
Bioinorganic Chemistry and Applications
Volume 2011, Article ID 173782, 13 pages
http://dx.doi.org/10.1155/2011/173782
Research Article

Dynamic Mechanical Response of Biomedical 316L Stainless Steel as Function of Strain Rate and Temperature

1Department of Mechanical Engineering, National Cheng Kung University, Tainan 701, Taiwan
2Department of Mechanical Engineering, National Kaohsiung University of Applied Sciences, Kaohsiung 807, Taiwan
3National Center for High-Performance Computing, Hsin-Shi Tainan 744, Taiwan

Received 30 June 2011; Revised 19 September 2011; Accepted 19 September 2011

Academic Editor: Concepción López

Copyright © 2011 Woei-Shyan Lee et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. E. Otero, A. Pardo, M. V. Utrilla, E. Saenz, and J. F. Alvarez, “Corrosion behaviour of AISI 304L and AISI 316L stainless steels prepared by powder metallurgy in the presence of sulphuric and phosphoric acid,” Corrosion Science, vol. 40, no. 8, pp. 1421–1434, 1998. View at Google Scholar
  2. R. A. Luna, J. G. Parr, and A. Hanson, “Stainless steel,” in Proceedings of the American Society for Microbiology (ASM '86), pp. 60–70, Metals Park, Ohio, USA, 1986.
  3. T. Kruml, J. Polák, and S. Degallaix, “Microstructure in 316LN stainless steel fatigued at low temperature,” Materials Science and Engineering A, vol. 293, no. 1-2, pp. 275–280, 2000. View at Publisher · View at Google Scholar · View at Scopus
  4. M. Gerland, R. Alain, B. Ait Saadi, and J. Mendez, “Low cycle fatigue behaviour in vacuum of a 316L-type austenitic stainless steel between 20 and 600C—part II: dislocation structure evolution and correlation with cyclic behaviour,” Materials Science and Engineering A, vol. 229, no. 1-2, pp. 68–86, 1997. View at Google Scholar · View at Scopus
  5. S. G. Hong and S. B. Lee, “The tensile and low cycle fatigue behaviour of cold worked 316L stainless steel: influence of dynamic strain aging,” International Journal of Fatigue, vol. 26, pp. 899–910, 2004. View at Google Scholar
  6. N. Maruyama, D. Mori, S. Hiromoto, K. Kanazawa, and M. Nakamura, “Fatigue strength of 316L-type stainless steel in simulated body fluids,” Corrosion Science, vol. 53, no. 6, pp. 2222–2227, 2011. View at Publisher · View at Google Scholar
  7. D. W. Kim, W. S. Ryu, J. H. Hong, and S. K. Choi, “Effect of nitrogen on high temperature low cycle fatigue behaviors in type 316L stainless steel,” Journal of Nuclear Materials, vol. 254, no. 2-3, pp. 226–233, 1998. View at Google Scholar · View at Scopus
  8. M. F. Abbod, C. M. Sellars, A. Tanaka, D. A. Linkens, and M. Mahfouf, “Effect of changing strain rate on flow stress during hot deformation of Type 316L stainless steel,” Materials Science and Engineering A, vol. 491, no. 1-2, pp. 290–296, 2008. View at Publisher · View at Google Scholar · View at Scopus
  9. L. E. Lindgren, K. Domkin, and S. Hansson, “Dislocations, vacancies and solute diffusion in physical based plasticity model for AISI 316L,” Mechanics of Materials, vol. 40, no. 11, pp. 907–919, 2008. View at Publisher · View at Google Scholar · View at Scopus
  10. M. N. A. Nasr, E. G. Ng, and M. A. Elbestawi, “Modelling the effects of tool-edge radius on residual stresses when orthogonal cutting AISI 316L,” International Journal of Machine Tools & Manufacture, vol. 47, no. 2, pp. 401–411, 2007. View at Publisher · View at Google Scholar · View at Scopus
  11. C. Herrera, R. L. Plaut, and A. F. Padilha, “Microstructural refinement during annealing of plastically deformed austenitic stainless steels,” Materials Science Forum, vol. 550, pp. 423–428, 2007. View at Publisher · View at Google Scholar · View at Scopus
  12. K. P. Staudhammer, L. E. Murr, and S. S. Hecker, “Nucleation and evolution of strain-induced martensitic (b.c.c.) embryos and substructure in stainless steel: a transmission electron microscope study,” Acta Metallurgica, vol. 31, no. 2, pp. 267–274, 1983. View at Google Scholar · View at Scopus
  13. S. P. Timothy and I. M. Hutchings, “Initiation and growth of microfractures along adiabatic shear bands in Ti-6Al-4V,” Materials Science and Technology, vol. 1, no. 7, pp. 526–530, 1985. View at Google Scholar · View at Scopus
  14. J. F. Molinari and M. Ortiz, “A study of solid-particle erosion of metallic targets,” Acta Metallurgica, vol. 27, no. 4, pp. 347–358, 2002. View at Publisher · View at Google Scholar · View at Scopus
  15. S. P. Timothy, “Structure of adiabatic shear bands in metals: a critical review,” Acta Metallurgica, vol. 35, no. 2, pp. 301–306, 1987. View at Google Scholar · View at Scopus
  16. W. S. Lee and C. F. Lin, “Adiabatic shear fracture of titanium alloy subjected to high strain and high temperature loadings,” Journal de Physique IV, vol. C3, pp. C3–C855, 1997. View at Google Scholar
  17. P. S. Follansbee and G. T. Gray, “An analysis of the low temperature, low and high strain-rate deformation of Ti-6Al-4V,” Metallurgical Transactions A, vol. 20, no. 5, pp. 863–874, 1989. View at Publisher · View at Google Scholar · View at Scopus
  18. M. A. Meyers, Y. J. Chen, F. D. S. Marquis, and D. S. Kim, “High-strain, high-strain-rate behavior of tantalum,” Metallurgical and Materials Transactions A, vol. 26, no. 10, pp. 2493–2501, 1995. View at Publisher · View at Google Scholar · View at Scopus
  19. W. G. Ferguson, A. Kumar, and J. E. Dorn, “Dislocation damping in aluminum at high strain rates,” Journal of Applied Physics, vol. 38, no. 4, pp. 1863–1869, 1967. View at Publisher · View at Google Scholar · View at Scopus
  20. A. Seeger, “Dislocations and mechanical properties of crystals,” Philosophical Magazine, vol. 46, pp. 1194–1217, 1955. View at Google Scholar
  21. W. S. Lee and C. F. Lin, “Comparative study of the impact response and microstructure of 304L stainless steel with and without prestrain,” Metallurgical and Materials Transactions A, vol. 33, no. 9, pp. 2801–2810, 2002. View at Google Scholar · View at Scopus
  22. J. L. Chiddister and L. E. Malvern, “Compression-impact testing of Aluminum at elevated temperatures,” Experimental Mechanics, vol. 3, no. 4, pp. 81–90, 1963. View at Publisher · View at Google Scholar · View at Scopus
  23. W. S. Lee and C. F. Lin, “Plastic deformation and fracture behaviour of Ti-6Al-4V alloy loaded with high strain rate under various temperatures,” Materials Science and Engineering A, vol. 241, no. 1-2, pp. 48–59, 1998. View at Google Scholar · View at Scopus
  24. W. S. Lee and T. H. Chen, “Dynamic mechanical response and microstructural evolution of high strength aluminum-scandium (Al-Sc) alloy,” Materials Transactions, vol. 47, no. 2, pp. 355–363, 2006. View at Publisher · View at Google Scholar · View at Scopus
  25. W. S. Lee, T. H. Chen, and H. H. Hwang, “Impact response and microstructural evolution of biomedical titanium alloy under various temperatures,” Metallurgical and Materials Transactions A, vol. 39, no. 6, pp. 1435–1448, 2008. View at Publisher · View at Google Scholar · View at Scopus
  26. W. S. Lee and T. H. Chen, “Effects of strain rate and temperature on dynamic mechanical behaviour and microstructural evolution in aluminium-scandium (Al-Sc) alloy,” Materials Science and Technology, vol. 24, no. 10, pp. 1271–1282, 2008. View at Publisher · View at Google Scholar · View at Scopus
  27. W. S. Lee and T. H. Chen, “Comparative study of dynamic impact properties and microstructures of weldable and unweldabe aluminum-scandium (Al-Sc) alloys,” Materials Science and Technology, vol. 25, pp. 1271–1282, 2009. View at Google Scholar
  28. W. S. Lee, T. H. Chen, C. F. Lin, and M. S. Chen, “Impact deformation behaviour and dislocation substructure of Al-Sc alloy,” Journal of Alloys and Compounds, vol. 493, no. 1-2, pp. 580–589, 2010. View at Publisher · View at Google Scholar · View at Scopus
  29. K. P. Staudhammer and L. E. Murr, “The effect of prior deformation on the residual microstructure of explosively deformed stainless steels,” Materials Science and Engineering, vol. 44, no. 1, pp. 97–113, 1980. View at Google Scholar · View at Scopus
  30. M. C. Mataya and V. E. Sackschewsky, “Effect of internal heating during hot compression on the stress-strain behavior of alloy 304L,” Metallurgical and Materials Transactions A, vol. 25, no. 12, pp. 2737–2752, 1994. View at Publisher · View at Google Scholar · View at Scopus
  31. R. Kapoor and S. Nemat-Nasser, “Determination of temperature rise during high strain rate deformation,” Mechanics of Materials, vol. 27, no. 1, pp. 1–12, 1998. View at Google Scholar · View at Scopus
  32. S. S. Ezz, Y. Q. Sun, and P. B. Hirsch, “Strain rate dependence of the flow stress and work hardening of γ′,” Materials Science and Engineering A, vol. 192-193, no. 1, pp. 45–52, 1995. View at Google Scholar · View at Scopus
  33. J. Harding, “Effect of temperature and strain rate on strength and ductility of four alloy steels,” Metals Technology, vol. 4, pp. 6–16, 1977. View at Google Scholar
  34. H. Conrad, “Thermally activated deformation of metals,” Journal of Metals, vol. 16, pp. 582–588, 1964. View at Google Scholar
  35. L. Shi and D. O. Northwood, “Mechanical behavior of an aisi type 310 stainless steel,” Acta Metallurgica et Materialia, vol. 43, no. 2, pp. 453–460, 1995. View at Publisher · View at Google Scholar · View at Scopus
  36. G. B. Gibbs, “Thermodynamic analysis of dislocation glide controlled by dispersed local obstacles,” Materials Science and Engineering, vol. 4, no. 6, pp. 313–328, 1969. View at Google Scholar · View at Scopus
  37. W. S. Lee and T. H. Chen, “Mechanical and microstructural response of aluminum-scandium (Al-Sc) alloy as a function of strain rate and temperature,” Materials Chemistry and Physics, vol. 113, no. 2-3, pp. 734–745, 2009. View at Publisher · View at Google Scholar · View at Scopus
  38. J. D. Campbell and W. G. Ferguson, “The temperature and strain-rate dependence of the shear strength of mild steel,” Philosophical Magazine, vol. 21, no. 169, pp. 63–82, 1970. View at Google Scholar · View at Scopus
  39. W. S. Lee and Y. C. Lin, “Strain rate and temperature dependence of dynamic shear properties of Al-Sc alloy,” Materials Science and Technology, vol. 22, no. 5, pp. 571–582, 2006. View at Publisher · View at Google Scholar · View at Scopus
  40. N. Fujita, S. Ryoji, T. Narushima, and C. Ouchi, “Austenitic grain growth behavior immediately after dynamic recrystallization in HSLA steels and austenitic stainless steel,” ISIJ International, vol. 48, no. 10, pp. 1419–1428, 2008. View at Publisher · View at Google Scholar · View at Scopus
  41. T. Sakai, “Dynamic recrystallization microstructures under hot working conditions,” Journal of Materials Processing Technology, vol. 53, no. 1-2, pp. 349–361, 1995. View at Google Scholar · View at Scopus