Table of Contents Author Guidelines Submit a Manuscript
BioMed Research International
Volume 2014 (2014), Article ID 790572, 6 pages
http://dx.doi.org/10.1155/2014/790572
Research Article

Initial Sliding Wear Kinetics of Two Types of Glass Ionomer Cement: A Tribological Study

1UFR d’Odontologie, Université de Lyon, 11 rue Guillame Paradin, 69372 Lyon, France
2Service de Consultations et Traitements Dentaires, Hospices Civils de Lyon, 6-8 Place Deperet, 69365 Lyon, France
3Laboratoire des Multimatériaux et Interfaces, CNRS UMR 5615, Université de Lyon, 11 rue Guillaume Paradin, 69372 Lyon, France
4Laboratoire de Génie des Procédés et Matériaux, Ecole Centrale Paris, Chemin des Vignes, 92295 Châtenay-Malabry, France
5UFR d’Odontologie, Université Denis Diderot Paris 7, 5 rue Garancière, 75006 Paris, France

Received 27 February 2014; Revised 3 June 2014; Accepted 4 June 2014; Published 29 June 2014

Academic Editor: Salvatore Sauro

Copyright © 2014 Cyril Villat et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. S. D. Heintze, “How to qualify and validate wear simulation devices and methods,” Dental Materials, vol. 22, no. 8, pp. 712–734, 2006. View at Publisher · View at Google Scholar · View at Scopus
  2. P. V. Antunes and A. Ramalho, “Study of abrasive resistance of composites for dental restoration by ball-cratering,” Wear, vol. 255, no. 7-12, pp. 990–998, 2003. View at Publisher · View at Google Scholar · View at Scopus
  3. P. Lambrechts, E. Debels, K. van Landuyt, M. Peumans, and B. van Meerbeek, “How to simulate wear? Overview of existing methods,” Dental Materials, vol. 22, no. 8, pp. 693–701, 2006. View at Publisher · View at Google Scholar · View at Scopus
  4. M. Shabanian and L. C. Richards, “In vitro wear rates of materials under different loads and varying pH,” Journal of Prosthetic Dentistry, vol. 87, no. 6, pp. 650–656, 2002. View at Publisher · View at Google Scholar · View at Scopus
  5. R. DeLong, “Intra-oral restorative materials wear: rethinking the current approaches: How to measure wear,” Dental Materials, vol. 22, no. 8, pp. 702–711, 2006. View at Publisher · View at Google Scholar · View at Scopus
  6. S. D. Heintze, A. Cavalleri, M. Forjanic, G. Zellweger, and V. Rousson, “A comparison of three different methods for the quantification of the in vitro wear of dental materials,” Dental Materials, vol. 22, no. 11, pp. 1051–1062, 2006. View at Publisher · View at Google Scholar · View at Scopus
  7. D. Xie, W. A. Brantley, B. M. Culbertson, and G. Wang, “Mechanical properties and microstructures of glass-ionomer cements,” Dental Materials, vol. 16, no. 2, pp. 129–138, 2000. View at Publisher · View at Google Scholar · View at Scopus
  8. C. Zantner, A. M. Kielbassa, P. Martus, and K. Kunzelmann, “Sliding wear of 19 commercially available composites and compomers,” Dental Materials, vol. 20, no. 3, pp. 277–285, 2004. View at Publisher · View at Google Scholar · View at Scopus
  9. W. M. Palin, G. J. P. Fleming, F. J. T. Burke et al., “The frictional coefficients and associated wear resistance of novel low-shrink resin-based composites,” Dental Materials, vol. 21, no. 12, pp. 1111–1118, 2005. View at Publisher · View at Google Scholar · View at Scopus
  10. R. N. B. Van Duinen, C. J. Kleverlaan, A. J. De Gee, A. Werner, and A. J. Feilzer, “Early and long-term wear of ‘Fast-set’ conventional glass-ionomer cements,” Dental Materials, vol. 21, no. 8, pp. 716–720, 2005. View at Publisher · View at Google Scholar · View at Scopus
  11. S. D. Heintze, G. Zappini, and V. Rousson, “Wear of ten dental restorative materials in five wear simulators—results of a round robin test,” Dental Materials, vol. 21, no. 4, pp. 304–317, 2005. View at Publisher · View at Google Scholar · View at Scopus
  12. J. F. Archard, “Contact and rubbing of flat surfaces,” Journal of Applied Physics, vol. 24, no. 8, pp. 981–988, 1953. View at Publisher · View at Google Scholar · View at Scopus
  13. L. Mair and A. Joiner, “The measurement of degradation and wear of three glass ionomers following peroxide bleaching,” Journal of Dentistry, vol. 32, supplement 1, pp. 41–45, 2004. View at Publisher · View at Google Scholar · View at Scopus
  14. J. Ellakuria, R. Triana, N. Mínguez et al., “Effect of one-year water storage on the surface microhardness of resin-modified versus conventional glass-ionomer cements,” Dental Materials, vol. 19, no. 4, pp. 286–290, 2003. View at Publisher · View at Google Scholar · View at Scopus
  15. L. A. Denisova, R. G. Maev, I. Y. Poyurovskaya et al., “The use of acoustic microscopy to study the mechanical properties of glass-ionomer cement,” Dental Materials, vol. 20, no. 4, pp. 358–363, 2004. View at Publisher · View at Google Scholar · View at Scopus
  16. S. Saito, S. Tosaki, and K. Hirota, “Characteristics of glass-ionomer cements,” in Advances in Glass-Ionomer Cements, pp. 15–50, Quintessence Publishing, New York, NY, USA, 1999. View at Google Scholar
  17. W. Kanchanavasita, H. M. Anstice, and G. J. Pearson, “Long-term surface micro-hardness of resin-modified glass ionomers,” Journal of Dentistry, vol. 26, no. 8, pp. 707–712, 1998. View at Publisher · View at Google Scholar · View at Scopus
  18. A. U. J. Yap, X. Wang, X. Wu, and S. M. Chung, “Comparative hardness and modulus of tooth-colored restoratives: a depth-sensing microindentation study,” Biomaterials, vol. 25, no. 11, pp. 2179–2185, 2004. View at Publisher · View at Google Scholar · View at Scopus
  19. A. U. J. Yap, Y. S. Pek, and P. Cheang, “Physico-mechanical properties of a fast-set highly viscous GIC restorative,” Journal of Oral Rehabilitation, vol. 30, no. 1, pp. 1–8, 2003. View at Publisher · View at Google Scholar · View at Scopus
  20. N. H. Abu-Bakr, L. Han, A. Okamoto, and M. Iwaku, “Changes in the mechanical properties and surface texture of compomer immersed in various media,” Journal of Prosthetic Dentistry, vol. 84, no. 4, pp. 444–452, 2000. View at Publisher · View at Google Scholar · View at Scopus
  21. K. Okada, S. Tosaki, K. Hirota, and W. R. Hume, “Surface hardness change of restorative filling materials stored in saliva,” Dental Materials, vol. 17, no. 1, pp. 34–39, 2001. View at Publisher · View at Google Scholar · View at Scopus
  22. S. Gladys, B. Van Meerbeek, M. Braem, P. Lambrechts, and G. Vanherle, “Comparative physico-mechanical characterization of new hybrid restorative materials with conventional glass-ionomer and resin composite restorative materials,” Journal of Dental Research, vol. 76, no. 4, pp. 883–894, 1997. View at Publisher · View at Google Scholar · View at Scopus
  23. A. U. J. Yap, “Post-irradiation hardness of resin-modified glass ionomer cements and a polyacid-modified composite resin,” Journal of Materials Science: Materials in Medicine, vol. 8, no. 7, pp. 413–416, 1997. View at Publisher · View at Google Scholar · View at Scopus
  24. Y. Z. Bayindir and M. Yildiz, “Surface hardness properties of resin-modified glass lonomer cements and polyacid-modified composite resins,” Journal of Contemporary Dental Practice, vol. 5, no. 4, pp. 42–49, 2004. View at Google Scholar · View at Scopus
  25. D. J. Callaghan, A. Vaziri, and H. Nayeb-Hashemi, “Effect of fiber volume fraction and length on the wear characteristics of glass fiber-reinforced dental composites,” Dental Materials, vol. 22, no. 1, pp. 84–93, 2006. View at Publisher · View at Google Scholar · View at Scopus
  26. M. T. Siniawski, S. J. Harris, and Q. Wang, “A universal wear law for abrasion,” Wear, vol. 262, no. 7-8, pp. 883–888, 2007. View at Publisher · View at Google Scholar · View at Scopus
  27. A. Ravikirana and S. C. Lim, “A better approach to wear-rate representation in non-conformal contacts,” Wear, vol. 225–229, pp. 1309–1314, 1999. View at Publisher · View at Google Scholar · View at Scopus
  28. A. Ravikiran and S. Jahanmir, “Effect of contact pressure and load on wear of alumina,” Wear, vol. 251, no. 1–12, pp. 980–984, 2001. View at Google Scholar · View at Scopus
  29. A. Cruzado, M. Hartelt, R. Wäsche, M. A. Urchegui, and X. Gómez, “Fretting wear of thin steel wires. Part 1: influence of contact pressure,” Wear, vol. 268, no. 11-12, pp. 1409–1416, 2010. View at Publisher · View at Google Scholar · View at Scopus
  30. J. Jiang and R. D. Arnell, “On the running-in behaviour of diamond-like carbon coatings under the ball-on-disk contact geometry,” Wear, vol. 217, no. 2, pp. 190–199, 1998. View at Publisher · View at Google Scholar · View at Scopus
  31. J. Jiang, F. H. Stott, and M. M. Stack, “The role of triboparticulates in dry sliding wear,” Tribology International, vol. 31, no. 5, pp. 245–256, 1998. View at Publisher · View at Google Scholar · View at Scopus
  32. P. J. Blau, “On the nature of running-in,” Tribology International, vol. 38, no. 11-12, pp. 1007–1012, 2005. View at Publisher · View at Google Scholar · View at Scopus
  33. H. Kato, “Severe-mild wear transition by supply of oxide particles on sliding surface,” Wear, vol. 255, no. 1–6, pp. 426–429, 2003. View at Publisher · View at Google Scholar · View at Scopus
  34. H. Kloss and R. Wäsche, “Analytical approach for wear prediction of metallic and ceramic materials in tribological applications,” Wear, vol. 266, no. 3-4, pp. 476–481, 2009. View at Publisher · View at Google Scholar · View at Scopus
  35. P. Põdra and S. Andersson, “Simulating sliding wear with finite element method,” Tribology International, vol. 32, no. 2, pp. 71–81, 1999. View at Publisher · View at Google Scholar · View at Scopus