Table of Contents Author Guidelines Submit a Manuscript
BioMed Research International
Volume 2017, Article ID 7376261, 9 pages
https://doi.org/10.1155/2017/7376261
Research Article

In Vitro Evaluation of Manual Torque Values Applied to Implant-Abutment Complex by Different Clinicians and Abutment Screw Loosening

1Private Practice, Istanbul, Turkey
2Department of Prosthodontics, Faculty of Dentistry, Istanbul University, Istanbul, Turkey
3Department of Dentomaxillofacial Radiology, Faculty of Dentistry, Istanbul University, Istanbul, Turkey
4Department of Statistics, Yıldız Technical University, Istanbul, Turkey
5Department of Mechanical Engineering, Faculty of Mechanical Engineering, Istanbul Technical University, Istanbul, Turkey
6Department of Oral and Maxillofacial Surgery, Faculty of Dentistry, Istanbul University, Istanbul, Turkey

Correspondence should be addressed to Onur Dincer Kose; moc.liamtoh@recnidruno.td

Received 2 November 2016; Revised 18 December 2016; Accepted 16 March 2017; Published 3 April 2017

Academic Editor: Konstantinos Michalakis

Copyright © 2017 Onur Dincer Kose et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. C. Y. Ha, Y. J. Lim, M. J. Kim, and J. H. Choi, “The influence of abutment angulation on screw loosening of the implants in the anterior maxilla,” The International Journal of Oral & Maxillofacial Implants, vol. 26, no. 1, pp. 45–55, 2011. View at Google Scholar
  2. S. Ünver, M. Bankoğlu Güngör, and S. Karakoca Nemli, “Dental implantlarda protetik komplikasyonlar,” ADO Klinik Bilimler Dergisi, vol. 6, no. 1, pp. 1109–1118, 2012. View at Google Scholar
  3. H. Siadat, S. Pirmoazen, E. Beyabanaki, and M. Alikhasi, “Does abutment collar length affect abutment screw loosening after cyclic loading?” Journal of Oral Implantology, vol. 41, pp. 346–351, 2015. View at Publisher · View at Google Scholar · View at Scopus
  4. K. L. Guzaitis, K. L. Knoernschild, and M. A. G. Viana, “Effect of repeated screw joint closing and opening cycles on implant prosthetic screw reverse torque and implant and screw thread morphology,” Journal of Prosthetic Dentistry, vol. 106, no. 3, pp. 159–169, 2011. View at Publisher · View at Google Scholar · View at Scopus
  5. A. Khraisat, A. Hashimoto, S. Nomura, and O. Miyakawa, “Effect of lateral cyclic loading on abutment screw loosening of an external hexagon implant system,” Journal of Prosthetic Dentistry, vol. 91, no. 4, pp. 326–334, 2004. View at Publisher · View at Google Scholar · View at Scopus
  6. D. Xia, H. Lin, S. Yuan, W. Bai, and G. Zheng, “Dynamic fatigue performance of implant-abutment assemblies with different tightening torque values,” Bio-Medical Materials and Engineering, vol. 24, no. 6, pp. 2143–2149, 2014. View at Publisher · View at Google Scholar · View at Scopus
  7. C. E. Misch, Dental İmplant Protezler, Nobel Tıp Kitabevleri, 2009.
  8. B. E. Pjetursson, U. Brägger, N. P. Lang, and M. Zwahlen, “Comparison of survival and complication rates of tooth-supported fixed dental prostheses (FDPs) and implant-supported FDPs and single crowns (SCs),” Clinical Oral Implants Research, vol. 18, no. 3, pp. 97–113, 2007. View at Publisher · View at Google Scholar · View at Scopus
  9. R. E. Jung, B. E. Pjetursson, R. Glauser, A. Zembic, M. Zwahlen, and N. P. Lang, “A systematic review of the 5-year survival and complication rates of implant-supported single crowns,” Clinical Oral Implants Research, vol. 19, no. 2, pp. 119–130, 2008. View at Publisher · View at Google Scholar · View at Scopus
  10. H.-M. Shin, J.-B. Huh, M.-J. Yun, Y.-C. Jeon, B. M. Chang, and C.-M. Jeong, “Influence of the implant-abutment connection design and diameter on the screw joint stability,” Journal of Advanced Prosthodontics, vol. 6, no. 2, pp. 126–132, 2014. View at Publisher · View at Google Scholar · View at Scopus
  11. J. H. Bickford, Introduction to the Design and Behavior of Bolted Joints, CRC Press, Boca Raton, Fla, USA, 2008.
  12. M. S. Schwarz, “Mechanical complications of dental implants,” Clinical Oral Implants Research, vol. 11, supplement 1, pp. 156–158, 2000. View at Publisher · View at Google Scholar · View at Scopus
  13. K. L. Goheen, S. G. Vermilyea, J. Vossoughi, and J. R. Agar, “Torque generated by handheld screwdrivers and mechanical torquing devices for osseointegrated implants,” The International Journal of Oral & Maxillofacial Implants, vol. 9, no. 2, pp. 149–155, 1994. View at Google Scholar · View at Scopus
  14. P. Bousquet, I. C. Bennasar, P. Tramini, M. Jacquemot, and F. Cuisinier, “Tightening of healing abutments: influence of torque on bacterial proliferation risk, an in vitro investigation,” Biomedizinische Technik, vol. 59, no. 6, pp. 495–500, 2014. View at Publisher · View at Google Scholar · View at Scopus
  15. M. Gross, D. Kozak, B. Z. Laufer, and E. I. Weiss, “Manual closing torque in five implant abutment systems: an in vitro comparative study,” The Journal of Prosthetic Dentistry, vol. 81, no. 5, pp. 574–578, 1999. View at Publisher · View at Google Scholar · View at Scopus
  16. L. Steinebrunner, S. Wolfart, K. Ludwig, and M. Kern, “Implant-abutment interface design affects fatigue and fracture strength of implants,” Clinical Oral Implants Research, vol. 19, no. 12, pp. 1276–1284, 2008. View at Publisher · View at Google Scholar · View at Scopus
  17. A. Balfour and G. R. O'Brien, “Comparative study of antirotational single tooth abutments,” The Journal of Prosthetic Dentistry, vol. 73, no. 1, pp. 36–43, 1995. View at Publisher · View at Google Scholar · View at Scopus
  18. L. Steinebrunner, S. Wolfart, K. Bössmann, and M. Kern, “In vitro evaluation of bacterial leakage along the implant-abutment interface of different implant systems,” International Journal of Oral and Maxillofacial Implants, vol. 20, no. 6, pp. 875–881, 2005. View at Google Scholar · View at Scopus
  19. T. Tsuge and Y. Hagiwara, “Influence of lateral-oblique cyclic loading on abutment screw loosening of internal and external hexagon implants,” Dental Materials Journal, vol. 28, no. 4, pp. 373–381, 2009. View at Publisher · View at Google Scholar · View at Scopus
  20. P. P. Binon and M. J. McHugh, “The effect of eliminating implant/abutment rotational misfit on screw joint stability,” International Journal of Prosthodontics, vol. 9, no. 6, pp. 511–519, 1996. View at Google Scholar · View at Scopus
  21. D. G. Gratton, S. A. Aquilino, and C. M. Stanford, “Micromotion and dynamic fatigue properties of the dental implant-abutment interface,” Journal of Prosthetic Dentistry, vol. 85, no. 1, pp. 47–52, 2001. View at Publisher · View at Google Scholar · View at Scopus
  22. P. C. P. Feitosa, A. P. B. de Lima, L. R. Silva-Concílio, W. C. Brandt, and A. C. Claro Neves, “Stability of external and internal implant connections after a fatigue test,” European Journal of Dentistry, vol. 7, no. 3, pp. 267–271, 2013. View at Publisher · View at Google Scholar · View at Scopus
  23. S. K. Kim, J. Y. Koak, S. J. Heo, T. D. Taylor, S. Ryoo, and S. Y. Lee, “Screw loosening with interchangeable abutments in internally connected implants after cyclic loading,” The International Journal of Oral & Maxillofacial Implants, vol. 27, no. 1, pp. 42–47, 2012. View at Google Scholar · View at Scopus
  24. C. E. Quek, K. B. Tan, and J. I. Nicholls, “Load fatigue performance of a single-tooth implant abutment system: effect of diameter,” International Journal of Oral and Maxillofacial Implants, vol. 21, no. 6, pp. 929–936, 2006. View at Google Scholar · View at Scopus