Table of Contents Author Guidelines Submit a Manuscript
BioMed Research International
Volume 2018, Article ID 2143906, 8 pages
https://doi.org/10.1155/2018/2143906
Research Article

Influence of Material Selection on the Marginal Accuracy of CAD/CAM-Fabricated Metal- and All-Ceramic Single Crown Copings

1Department of Prosthodontics, University Medical Center Goettingen, Robert-Koch-Str. 40, 37075 Goettingen, Germany
2Private Practice, Geleitstr. 68, 63456 Hanau, Germany

Correspondence should be addressed to Matthias Rödiger; ed.gdwg@gideorm

Received 4 December 2017; Accepted 14 February 2018; Published 22 March 2018

Academic Editor: Konstantinos Michalakis

Copyright © 2018 Matthias Rödiger et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

Linked References

  1. I. Sailer, N. A. Makarov, D. S. Thoma, M. Zwahlen, and B. E. Pjetursson, “All-ceramic or metal-ceramic tooth-supported fixed dental prostheses (FDPs)? A systematic review of the survival and complication rates. Part I: single crowns (SCs),” Dental Materials, vol. 31, no. 6, pp. 603–623, 2015. View at Publisher · View at Google Scholar · View at Scopus
  2. A. Aldegheishem, G. Ioannidis, W. Att, and H. Petridis, “Success and survival of various types of all-ceramic single crowns: A critical review and analysis of studies with a mean follow-up of 5 years or longer,” International Journal of Prosthodontics, vol. 30, no. 2, pp. 168–181, 2017. View at Publisher · View at Google Scholar · View at Scopus
  3. T. F. Alghazzawi, “Advancements in CAD/CAM technology: Options for practical implementation,” Journal of Prosthodontic Research, vol. 60, no. 2, pp. 72–84, 2016. View at Publisher · View at Google Scholar · View at Scopus
  4. R. Prasad and A. A. Al-Kheraif, “Three-dimensional accuracy of CAD/CAM titanium and ceramic superstructures for implant abutments using spiral scan microtomography,” International Journal of Prosthodontics, vol. 26, no. 5, pp. 451–457, 2013. View at Publisher · View at Google Scholar · View at Scopus
  5. T. A. Hamza, H. A. Ezzat, M. M. K. El-Hossary, H. A. E. M. Katamish, T. E. Shokry, and S. F. Rosenstiel, “Accuracy of ceramic restorations made with two CAD/CAM systems,” Journal of Prosthetic Dentistry, vol. 109, no. 2, pp. 83–87, 2013. View at Publisher · View at Google Scholar
  6. F. Martínez-Rus, A. Ferreiroa, M. Özcan, and G. Pradíes, “Marginal discrepancy of monolithic and veneered all-ceramic crowns on titanium and zirconia implant abutments before and after adhesive cementation: A scanning electron microscopy analysis,” The International Journal of Oral & Maxillofacial Implants, vol. 28, no. 2, pp. 480–487, 2013. View at Publisher · View at Google Scholar · View at Scopus
  7. G. M. de Araújo, D. G. B. de França, J. P. S. Neto, and G. A. S. Barbosa, “Passivity of conventional and CAD/ CAM fabricated implant frameworks,” Brazilian Dental Journal, vol. 26, no. 3, pp. 277–283, 2015. View at Publisher · View at Google Scholar · View at Scopus
  8. C. Keul, B. Stawarczyk, K.-J. Erdelt, F. Beuer, D. Edelhoff, and J.-F. Güth, “Fit of 4-unit FDPs made of zirconia and CoCr-alloy after chairside and labside digitalization - A laboratory study,” Dental Materials, vol. 30, no. 4, pp. 400–407, 2014. View at Publisher · View at Google Scholar · View at Scopus
  9. K. Ueda, F. Beuer, M. Stimmelmayr, K. Erdelt, C. Keul, and J.-F. Güth, “Fit of 4-unit FDPs from CoCr and zirconia after conventional and digital impressions,” Clinical Oral Investigations, vol. 20, no. 2, pp. 283–289, 2016. View at Publisher · View at Google Scholar · View at Scopus
  10. M. Contrepois, A. Soenen, M. Bartala, and O. Laviole, “Marginal adaptation of ceramic crowns: A systematic review,” Journal of Prosthetic Dentistry, vol. 110, no. 6, pp. 447–E10, 2013. View at Publisher · View at Google Scholar · View at Scopus
  11. N. A. Nawafleh, F. Mack, J. Evans, J. Mackay, and M. M. Hatamleh, “Accuracy and reliability of methods to measure marginal adaptation of crowns and FDPs: a literature review,” Journal of Prosthodontics, vol. 22, no. 5, pp. 419–428, 2013. View at Publisher · View at Google Scholar · View at Scopus
  12. P. Kosyfaki, M. Del Pilar Pinilla Martín, and J. R. Strub, “Relationship between crowns and the periodontium: A literature update,” Quintessence International, vol. 41, no. 2, pp. 109–122, 2010. View at Google Scholar · View at Scopus
  13. S. Rinke, D. Fornefett, N. Gersdorff, K. Lange, and M. Roediger, “Multifactorial analysis of the impact of different manufacturing processes on the marginal fit of zirconia copings,” Dental Materials, vol. 31, no. 4, pp. 601–609, 2012. View at Publisher · View at Google Scholar · View at Scopus
  14. J. R. Holmes, S. C. Bayne, G. A. Holland, and W. D. Sulik, “Considerations in measurement of marginal fit,” Journal of Prosthetic Dentistry, vol. 62, no. 4, pp. 405–408, 1989. View at Publisher · View at Google Scholar · View at Scopus
  15. J. W. McLean and J. A. von Fraunhofer, “The estimation of cement film thickness by an in vivo technique,” British Dental Journal, vol. 131, no. 3, pp. 107–111, 1971. View at Publisher · View at Google Scholar · View at Scopus
  16. P. Vigolo and F. Fonzi, “An in vitro evaluation of fit of zirconium-oxide-based ceramic four-unit fixed partial dentures, generated with three different CAD/CAM systems, before and after porcelain firing cycles and after glaze cycles,” Journal of Prosthodontics, vol. 17, no. 8, pp. 621–626, 2008. View at Publisher · View at Google Scholar · View at Scopus
  17. T. E. Shokry, M. Attia, I. Mosleh, M. Elhosary, T. Hamza, and C. Shen, “Effect of metal selection and porcelain firing on the marginal accuracy of titanium-based metal ceramic restorations,” Journal of Prosthetic Dentistry, vol. 103, no. 1, pp. 45–52, 2010. View at Publisher · View at Google Scholar · View at Scopus
  18. E. Gonzalo, M. J. Suárez, B. Serrano, and J. F. L. Lozano, “A comparison of the marginal vertical discrepancies of zirconium and metal ceramic posterior fixed dental prostheses before and after cementation,” The Journal of Prosthetic Dentistry, vol. 102, no. 6, pp. 378–384, 2009. View at Publisher · View at Google Scholar · View at Scopus
  19. G. A. Borges, J. S. Faria, P. Agarwal, A. M. Spohr, L. Correr-Sobrinho, and B. A. S. Miranzi, “In vitro marginal fit of three all-ceramic crown systems before and after cementation,” Operative Dentistry, vol. 37, no. 6, pp. 641–649, 2012. View at Publisher · View at Google Scholar · View at Scopus
  20. M. Groten, D. Axmann, L. Pröbster, and H. Weber, “Determination of the minimum number of marginal gap measurements required for practical in vitro testing,” Journal of Prosthetic Dentistry, vol. 83, no. 1, pp. 40–49, 2000. View at Publisher · View at Google Scholar · View at Scopus
  21. N. Lövgren, R. Roxner, S. Klemendz, and C. Larsson, “Effect of production method on surface roughness, marginal and internal fit, and retention of cobalt-chromium single crowns,” Journal of Prosthetic Dentistry, vol. 118, no. 1, pp. 95–101, 2017. View at Publisher · View at Google Scholar · View at Scopus
  22. S.-J. Ha and J.-H. Cho, “Comparison of the fit accuracy of zirconiabased prostheses generated by two CAD/CAM systems,” The Journal of Advanced Prosthodontics, vol. 8, no. 6, pp. 439–448, 2016. View at Publisher · View at Google Scholar · View at Scopus
  23. R. Roperto, H. Assaf, T. Soares-Porto, L. Lang, and S. Teich, “Are different generations of CAD/CAM milling machines capable to produce restorations with similar quality?” Journal of Clinical and Experimental Dentistry, vol. 18, no. 4, Article ID 52984, pp. 423–428, 2016. View at Publisher · View at Google Scholar · View at Scopus
  24. Z. Huang, L. Zhang, J. Zhu, Y. Zhao, and X. Zhang, “Clinical marginal and internal fit of crowns fabricated using different CAD/CAM technologies,” Journal of Prosthodontics, vol. 24, no. 4, pp. 291–295, 2015. View at Publisher · View at Google Scholar · View at Scopus
  25. R. Mounajjed, D. M. Layton, and B. Azar, “The marginal fit of E.max press and E.max CAD lithium disilicate restorations: A critical review,” Dental Materials, vol. 35, no. 6, pp. 835–844, 2016. View at Publisher · View at Google Scholar · View at Scopus
  26. P. Boitelle, B. Mawussi, L. Tapie, and O. Fromentin, “A systematic review of CAD/CAM fit restoration evaluations,” Journal of Oral Rehabilitation, vol. 41, no. 11, pp. 853–874, 2014. View at Publisher · View at Google Scholar · View at Scopus
  27. P. K. Brawek, S. Wolfart, L. Endres, A. Kirsten, and S. Reich, “The clinical accuracy of single crowns exclusively fabricated by digital workflow-the comparison of two systems,” Clinical Oral Investigations, vol. 17, no. 9, pp. 2119–2125, 2013. View at Publisher · View at Google Scholar · View at Scopus
  28. M. Borba, P. F. Cesar, J. A. Griggs, and Á. D. Bona, “Adaptation of all-ceramic fixed partial dentures,” Dental Materials, vol. 27, no. 11, pp. 1119–1126, 2011. View at Publisher · View at Google Scholar · View at Scopus
  29. M. C. Balkaya, A. Cinar, and S. Pamuk, “Influence of firing cycles on the margin distortion of 3 all-ceramic crown systems,” Journal of Prosthetic Dentistry, vol. 93, no. 4, pp. 346–355, 2005. View at Publisher · View at Google Scholar · View at Scopus
  30. A. F. Quintas, F. Oliveira, and M. A. Bottino, “Vertical marginal discrepancy of ceramic copings with different ceramic materials, finish lines, and luting agents: an in vitro evaluation,” Journal of Prosthetic Dentistry, vol. 92, no. 3, pp. 250–257, 2004. View at Publisher · View at Google Scholar · View at Scopus
  31. R. Chavali, A. H. Nejat, and N. C. Lawson, “Machinability of CAD-CAM materials,” Journal of Prosthetic Dentistry, vol. 118, no. 2, pp. 194–199, 2017. View at Publisher · View at Google Scholar · View at Scopus